Análise do custo-benefício de sistemas de cobertas em edificações comerciais para o clima de Natal/RN visando eficiência energética

This research consists in studying the influence of the various type of construction systems of roofs with their energy efficiency as well as on the cost benefit for the commercial buildings on the temperatures condition of the city of Natal/RN. The main goal of this research is to analyze the cost benefit of the construction systems of roofs available on the market, taking into consideration the energy efficiency of the commercial buildings artificially air conditioned in order to be used by the projectors and to be adequated to the temperatures condition of the city of Natal/RN. The method of valuation of the cost benefit of roof systems consists in six steps: Features and simulation of the reference building; Analyze of sensitivity; Analyzes, features and simulation of alternatives of roof construction systems; Analyze of the cost of implementation; Analyze of the benefits of the alternatives comparing to the base case; And finally the analyze of the cost benefit. The model type chosen as reference was stores with pre molded buildings and system of roof with fiber ciment and ceiling . The thermal results showed the influence of the roof system on the energy efficiency of the building. The Final results of the simulations of the alternatives comes to a conclusion that the absortance is the variable that presents the best cost benefit relation and the reduction on the thermal transmittance still has limitations because of the high cost

Obtenção e caracterização de dióxido de estanho nanoestruturado pelo método de síntese contínua por combustão em solução

Continuous Synthesis by Solution Combustion was employed in this work aiming to obtain tin dioxide nanostructured. Basically, a precursor solution is prepared and then be atomized and sprayed into the flame, where its combustion occurs, leading to the formation of particles. This is a recent technique that shows an enormous potential in oxides deposition, mainly by the low cost of equipment and precursors employed. The tin dioxide (SnO2) nanostructured has been widely used in various applications, especially as gas sensors and varistors. In the case of sensors based on semiconducting ceramics, where surface reactions are responsible for the detection of gases, the importance of surface area and particle size is even greater. The preference for a nanostructured material is based on its significant increase in surface area compared to conventional microcrystalline powders and small particle size, which may benefit certain properties such as high electrical conductivity, high thermal stability, mechanical and chemical. In this work, were employed as precursor solution tin chloride dehydrate diluted in anhydrous ethyl alcohol. Were utilized molar ratio chloride/solvent of 0,75 with the purpose of investigate its influence in the microstructure of produced powder. The solution precursor flux was 3 mL/min. Analysis with X-ray diffraction appointed that a solution precursor with molar ratio chloride/solvent of 0,75 leads to crystalline powder with single phase and all peaks are attributed to phase SnO2. Parameters as distance from the flame with atomizer distance from the capture system with the pilot, molar ratio and solution flux doesn t affect the presence of tin dioxide in the produced powder. In the characterization of the obtained powder techniques were used as thermogravimetric (TGA) and thermodiferential analysis (DTA), particle size by laser diffraction (GDL), crystallographic analysis by X-ray diffraction (XRD), morphology by scanning electron microscopy (SEM), transmission electron microscopy (TEM), specific surface area (BET) and electrical conductivity analysis. The techniques used revealed that the SnO2 exhibits behavior of a semiconductor material, and a potentially promising material for application as varistor and sensor systems for gas

A Fruticultura Irrigada de pequenos produtores no Baixo-Açu: Uma análise da eficiência de custo

This work has as an objective analyze the efficiency of producers costs of the irrigation Project Baixo-Açu , and identify the determining factors of this efficiency. To achieve these targets it was estimated, in a first stage, a frontier of costs by the method, non parametric of Data Envelopment Analysis-DEA, and measured the stakes of efficiency producers. On the second stage, it was utilized the Tobit regression pattern, estimating an inefficiency function of costs, and were indentified the associated factors of resources waste. Among the results found it was noticed the existence of a high waste of resources, that represent more than 54% of effective cost. Among the factors with the highest wastes are: energy, herbicides, defensives and chemical fertilizers. In a general way, the producers presented low efficiency level and, only, two, of seventy-five researched, achieved the frontier of costs minimization. These results reveal, in a certain way, that the producers in irrigated fruit growing in the project Baixo-Açu don t seek to minimize the production costs. It was still noticed, that the reduction of resources waste, and this way the inefficiency of costs, is associated with the agriculturalist education, his experience in agriculture, his access to the technical assistance and credit

Custo social de oportunidade na trajetória de acesso ao ensino superior: o caso dos ingressantes na UFRN nos vestibulares de 2006 a 2010

Access is a problem of higher education in Brazil that has existed since the formalization of this has occurred since the installation of the Portuguese court in Brazil in 1808. Only 10% of young people between 18 and 24 years of age attending this level of education in 2000, arriving in 2010 just 15%, far from that determined the National Education Plan in 2001, triple that percentage by the year 2010. In addition, a majority of seats of public HEIs is populated by students from the private network, especially in high-demand courses. In this context, this study aims to identify the costs related to the trajectories of students who were successful in the vestibular UFRN editions from 2006 to 2010. Presents an overview of higher education in Brazil, a brief history of vestibular, as well as new forms of access, and some of the policies to expand such access, highlighting the argument Inclusion UFRN. Focusing on the theme of the paper presents the concepts of opportunity costs and social. After collecting data through a questionnaire and consultation of databases COMPERVE was developed to search for a descriptive and analytical, with the participation of 3,995 students, of whom 1642 (41.1%) had completed secondary education in schools public, and 2,078 (52%) in private schools. The profile indicates that 90% are single, about 50% are 21 years of age, are white and female. In the course of preparation for college entrance exams, 80% chose the course during or after completion of the last year of high school, and almost 70% said they had started preparing at that time. Findings related to the costs involved with this preparation indicate that, in most cases there were school fees and disbursements and workshops, and the purchase of books and other materials, with parents primarily responsible for this cost, the amount disbursed each month was up $ 300 for 64% of respondents and only 7% of them exceeded $ 1,000, the major non-financial costs were characterized by the following resignations: job opportunities (24%) or temporary work (20%) courses of languages (26%), leisure activities (48%), leisure travel (43%), and parties and / or shows (54%). Of social investments by the government, stand out in the tax waiver scholarships for study in private institutions, grant exemption from the registration fee of vestibular, the preparatory courses UFRN, and seminars by COMPERVE / UFRN with networks of high school. From the junction of the opportunity costs (private costs) and social costs (public costs), a new concept: the social opportunity cost, which measures the combined efforts of families and government to finance the opportunity to access higher education of an individual. This concept can and should be incorporated as a strategic vector for the sake of democratic university, which reflects the social model that is sought

Custo-efetividade da terapia compressiva no processo de cicatrização de úlceras venosas

Analytical study of therapeutic nonrandomized intervention type, intra-group controlled, with the aim of analyzing the cost-effectiveness of compression therapy with manipulated Unna boot in relation to conventional therapy in the healing of venous ulcers (VU) of patients treated in ambulatory clinic. The study population was composed by patients with VU treated by angiologists in Surgical Clinic Ambulatory of the Onofre Lopes University Hospital (HUOL) with a sample of 18 patients. It obtained the assent of the HUOL Ethics in Research Committee (Protocol 276/09). Data collection was performed over a period of four months by the own master's student and 34 nursing students, through the application of the research instrument in the admission of patients to the study and in the ten subsequent evaluations, performed at the time of changing Unna boot, weekly, for a maximum period of 10 weeks. The data were analyzed with SPSS 15.0 software, using descriptive and inferential statistics, and presented as tables, charts and graphs. Among those surveyed, prevailed: females, mean age 57.6 years, low education and income levels, most retired, unemployed or off work, with the standing position more than six hours per day and up to eight hours daily of domestic or occupational activities. In health status profile of respondents there were predominantly sleep, rest and inadequate elevation of the lower limbs, no smoking and/or alcohol use, presence of hypertension and no use of drugs. Most presented the first VU for over 10 years, recurrences, present VU for more than five years, involvement of left leg, in malleolar and / or distal leg region, mild edema, hyperpigmentation, lipodermatosclerosis, telangiectasies, reticular and varicose veins, mild pain, serous exudate in moderate quantity, small lesions (up to 50cm2), with predominance of granulation tissue and / or epithelialization and demarcated, elevated and irregular borders, with crusts and macerated. Most patients reported that in the 10 weeks prior to admission, made bandages at home and / or Basic Health Unit and / or ambulatory, with nursing aides or technicians, daily, and on weekends or holidays, performed by patients themselves, using healing ointment on the lesion, being observed granulation / epithelialization and increase in VU prevalent in the 10 weeks of traditional treatment. After follow up with manipulated Unna boot, was observed a decrease of lesions in all study patients, with complete healing in 27.8% of those between 1 and 5 weeks of treatment, with satisfactory evolution of the lesions, pain and ankle and calf circumferences, and unsatisfactory development of the borders of ulcers, edema, sleep, rest and elevation of the lower limbs, especially in more chronic patients. Furthermore, patients who achieved total healing and exhibited the greatest percentage reduction of lesions had a higher number of wound healing factors (ρ = 0.01 and ρ = 0.027, respectively). The manipulated Unna boot showed better results in those patients with shorter duration of injury, leading them to a satisfactory outcome within a short period of treatment. After the cost-effectiveness analysis, we conclude that the manipulated Unna boot is more effective than conventional therapy in the healing process of VU and is more cost-effective in patients with shorter lesions (ρ = 0.001), shorter treatment (ρ = 0.000) and greater number of wound healing factors (ρ = 0.005).

Plataforma Robótica de Baixíssimo Custo para Robótica Educacional

Robots are present each time more on several areas of our society, however they are still considered expensive equipments that are restricted to few people. This work con- sists on the development of control techniques and architectures that make possible the construction and programming of low cost robots with low programming and building complexity. One key aspect of the proposed architecture is the use of audio interfaces to control actuators and read sensors, thus allowing the usage of any device that can produce sounds as a control unit of a robot. The work also includes the development of web ba- sed programming environments that allow the usage of computers or mobile phones as control units of the robot, which can be remotely programmed and controlled. The work also includes possible applications of such low cost robotic platform, including mainly its educational usage, which was experimentally validated by teachers and students of seve- ral graduation courses. We also present an analysis of data obtained from interviews done with the students before and after the use of our platform, which confirms its acceptance as a teaching support tool

Uma proposta de metodologia para o ensino de Física usando robótica de baixíssimo custo

This paper presents methodology based on Lev Vigotsky`s social interactionist theory through investigative activities, which integrates the teaching of physics to robotics, directed to students of the Physics degree course, seeking to provide further training for future teachers. The method is organized through educational robotics workshops that addresses concepts of physics through the use of low-cost educational robots along with several activities. The methodology has been presented and discussed and put into practice afterwards in workshops so that these future teachers may be able to take robotics to their classroom. Students from the last and penultimate semester of the Physics degree course of the Federal Institute of Education, Science and Technology of Rio Grande do Norte, Caicó campus participated in this project

Controle de posição de uma plataforma plana para captação de radiação solar

This study aims at the design, development and performance evaluation of a flat platform to capture incident solar radiation. The design and implementation of a fuzzy system for the efficient control of the solar tracking movement of the platform are also presented

Viabilidades térmica, econômica e de materiais de um sistema solar de aquecimento de água a baixo custo para fins residenciais

An solar alternative system for water heating is presented. Is composed for one low cost alternative collector and alternative thermal reservoir for hot water storing. The collector of the system has box confectioned in composite material and use absorption coils formed for PVC tubes. The box of hot water storage was confectioned from a plastic polyethylene drum used for storage of water and garbage, coated for a cylinder confectioned in fiber glass. The principle of functioning of the system is the same of the conventionally. Its regimen of work is the thermosiphon for a volume of 250 liters water. The main characteristic of the system in considered study is its low cost, allowing a bigger socialization of the use of solar energy. It will be demonstrated the viabilities thermal, economic and of materials of the system of considered heating, and its competitiveness in relation to the available collectors commercially. Relative aspects will be boarded also the susceptibility the thermal degradation and for UV for the PVC tubes. It will be shown that such system of alternative heating, that has as main characteristic its low cost, presents viabilities thermal, economic and of materials

Estudo da Potencialidade da produção de tijolos de adobe misturado com outros materiais: uma alternativa de baixo custo para a construção civil

The production of the red pottery brick, made traditionally with clay, is a technique that is already stabled. However, in spite of the little complexity that involves the conventional process of these bricks production, it are exposed to many problems that begin in the fase of exploration of the mines, the problems get worse because of the lack of the clay's characterization, and they continue through the steps of the dough preparation, conformation of the products, the drying and the burning process. The wastefulness is shown and so is the low quality of the material produced. Among other factors, the high use of energy in the burning makes the cost of this material inaccessible to the low income consumer. Besides this, the destruction of the environment around the mines and the use of native vegetation to produce wood - the most used fuel in the pottery industry - make serious environmental damage. The production technique of a new type of simple brick (adobe), that has low cost and no environmental damage, can be the viable altemative to lower the cost of this part of the civil construction, and, consequently, in the building of cheaper houses. In this paper, the results of the mechanical resistance of the adobe brick are shown, using in its composition, clay, natural vegetable fibers, cement and plaster in a process that is completely handcrafted and manual. It is intented to make clear that are possible alternatives to be put in practice, with the simple process, using "raw earth" that has been used in the construction of houses in thousands of years, trying to solve these severe problems. Analysis and tests were performed to find results that could prove the possibility of the utilization of this kind of material. Other studies are in progress, and the new researches are necessary to enrich this work, but it stays the certainty that there is potential to produce bricks from adobe, as an alternative that has low cost to civil construction

Construção, calibração e análise de desempenho de um piranômetro de baixo custo, baseado no modelo Kimball-Hobbs

In this work a pyrometer using the classic model of Kimball-Hobbs was developed, tested and calibrated. The solar radiation is verified through the temperature difference between the sensible elements covered by absorbing (black) and reflecting (white) pigmentations of the incoming radiation. The photoacoustic technique was used to optimize the choice of the pigments. Methodologies associated with linearity, thermo-variation, sensibility, response time and distance are also presented. To correctly classify the results, the international standard ISO 9060 as well as indicative parameters of World Meteorological Organization (WMO) are used. In addition a system of data acquisition of two channels with 12 bits, constructed during the this time, was used to measure the global solar radiation on the ground by the pyrometer and also by another pyrometer certified in the case of Keep & zonen. The results statistically show, through the hypothesis test presented here, that both equipments find population average with 95% of correctness

Projeto, construção e análise de desempenho de um forno solar alternativo tipo caixa a baixo custo

An alternative box-type solar oven constructed from the scrap iron of a gas conventional cook is presented, which functions principles are the effect greenhouse and the concentration. The oven of the conventional cook is the baking enclosure where the absorber (pot) of the solar oven is located, being re-covered for a glass blade for the generation of the greenhouse effect isolated lateral and having deep its and for a composite the plaster base and EPS. Segments of plain mirrors had been placed in the laterals of the oven for the concentration of the radiation and a reflecting parabola was introduced in the baking enclosure for the exploitation of the incident reflected radiation in the interior of the oven. The oven is mobile to allow one better aiming of exactly in relation to the apparent movement of the sun. The thermal economic and of materials viabilities of the stove in study will be demonstrate The average internal temperature of the absorber was around 150°C and the internal temperature around 120°C. Will demonstrate that its low cost and good thermal performance represents basic characteristics for the viability of large use of such archetype, mainly for cooking the decreases and averages temperatures. One will reveal that the archetype in study is competitive with the box-type solar cooker conceived in the whole world

Estudo térmico de um sistema solar de aquecimento de água residencial para duas configurações de superfície absorvedora

It presents a solar collector to be used in a system for heating water for bathing, whose main characteristics are its low cost and easy manufacturing and assembly. The absorbing surface of the collector is formed by an aluminum plate with eight flaps where they lodge PVC pipes. The catchment area of solar radiation corresponds to 1.3 meters. The collector box was made of wood, is covered by transparent glass and thermal insulation of tire chips and expanded polystyrene (EPS). Absorber tubes were connected in parallel through the use of PVC fittings and fixed to the plate by the use of metal poles and rivets. The entire absorber received paint flat black for better absorption of sunlight. The system worked on a thermosiphon assembly and absorber of the collector has been tested in two configurations: with the tubes facing up, directly exposed to the impact of sunlight and facing down, exchanging heat with the plate by conduction. It was determined the most efficient configuration for the correct purpose. The solar collector was connected to a thermal reservoir, also alternative, low-cost forming the system of solar water heating. We evaluated thermal parameters that proved the viability of the heating system studied

Construção e análise de desempenho de um forno/fogão solar tipo caixa construído a partir de uma sucata de pneu

An alternative box-type solar cooker built starting from the scrap of a tire and a scrap of old office chair is presented, which principles functions are the effect greenhouse and the concentration. The tire served as structure for making of is the baking enclosure where the absorber (roasting pan 20x30cm) of the solar is located, being re-covered for a glass blade for the generation of the greenhouse effect isolated lateral and having deep its and for a composite the plaster base and EPS. Segments of plain mirrors had been placed in the laterals of the oven/cook for the concentration of the radiation and a reflecting parable was introduced in the baking enclosure for the exploitation of the incident reflected radiation inside of the oven/cook. The oven/cook is mobile to allow one better aiming of exactly in relation to the apparent movement of the sun. The thermal economic and of materials viabilities of the stove/cook in study will be demonstrate. The average internal temperature of the absorber was around 152,3°C and the internal temperature around 110°C. Will demonstrate that toits low cost and good thermal performance, represents basic characteristics for the viability of large use of such archetype, mainly for cooking the decreases and averages temperatures. One will reveal that the archetype in study is competitive with the box-type solar cooker conceived in the whole world

Análise do desempenho térmico de um sistema de aquecimento solar de baixo custo

It presents a solar collector to be used in a system for heating water for bathing, whose main characteristics are low cost and easy manufacturing and assembly. The system operates under natural convection or thermosiphon. The absorbing surface of the collector is formed by twelve PVC pipes of 25 mm outside diameter connected in parallel via connections in T of the same material. The tubes were covered with absorbing fins made with recycled aluminum cans. We studied eight settings between absorber plate, thermal insulating EPS boards and thermal reservoirs 150 and 200 liters. It was determined the most efficient configuration for the correct purpose. We evaluated thermal parameters that proved the viability of the heating system studied