Estruturas cerâmicas a base de zircônia e alumina utilizadas na confecção de infra - estruturas para coroas e pontes fixas

The continuous advances in ceramic systems for crowns and bridges infrastructure getting researchers and manufacturers looking for a material that has good mechanical properties and aesthetic. The purpose of this study was to verify in which composition and sintering temperature the ceramic system for infrastructure composed of alumina and zirconia would have the best mechanical properties. With this objective we made in UFRN laboratories 45 test bodies in the form of rectangular bars with the following dimensions: 30mm x 8mm x 3mm, where we separated by the sintering temperature: 1200°C, 1300ºC and 1400ºC, and by comp osition: 33% Zirconia + 67% Alumina; 50% Zirconia + 50% Alumina and 25% Zirconia + 75% Alumina, these test bodies were not infiltrated with glass. Also, were made nine test bodies by a technical from a laboratory with a commercial ceramic system: in the Ceram Zircônia (Vita - Zahnfabrik) with the following dimensions: 20mm x 10mm x 0.5mm, these test bodies following all recommendations of the manufacturer and were infiltrated with glass. Were realized optical and electronic microscopy analyses, hardness testing, resistance to bending in three points, porosity and bulk density. After analysis of the results we verified that with the increasing of sintering temperature, increased the value of resistance to bending, but with the same temperature there was no significant difference between the different compositions, samples made with the commercial ceramic that were infiltrated, presented a resistance to bending six times greater than the samples sintered to 1400°C and which have not been infiltra ted. There was no significant difference between the values of apparent porosity for the samples made in UFRN laboratories, but the samples of commercial ceramic obtained 0% in porosity apparent value. In tests of Rockwell Hardness there is an increase in the value of Hardness, with the increase of sintering temperature for the samples not infiltrated. Samples infiltrated showed similar values as the samples sintered in 1400°C. There was no significant difference between the values of apparent density among samples manufactured in UFRN laboratories and samples made with a commercial ceramic

Atrás das grades: redes sociais, habitus e interação social no sistema carcerário do RN

Esta tesis trata de discutir y entender los diversos tipos de redes sociales y formas de interacción social presentes en el sistema penitenciario de Rio Grande do Norte. Nuestro problema se basa en un incremento significativo en las tasas de encarcelamiento y la prisión en Brasil y el mundo en los últimos diez años. Asimismo, la aparición del crimen organizado ya, en cierta medida, el control de las prisiones brasileñas, como el Comando Vermelho (CV) y el Primeiro Comando da Capital (PCC), una consecuencia directa de las terribles condiciones de las prisiones de Brasil y aumento de la violencia y el crimen en nuestro país. Para resolver el problema, se optó por utilizar las categorías de análisis de Michel Foucault (prisión y la disciplina), Pierre Bourdieu (habitus y campo), Ervirng Goffman (institución total, de interacción, de fachada y de equipo) y Mark Granovetter, Ricardo Abramovay e João Peixoto, entre otros, la nueva sociología económica (Redes, nodos y lazos) como principal apoyo. También construyó una revisión histórica de la cárcel en Brasil y Rio Grande do Norte hasta llegar al objeto. Esto, en términos de investigación cualitativa, se sumergió en el mundo de las prisiones Dr. Francisco Nogueira Fernandes, conocido como Penitenciario de Alcaçuz, ubicado en el municipio de Nísia Bosque, Rio Grande do Norte. Penitenciaría del Estado de origen, las casas de Alcaçuz seiscientos cuarenta y tres reclusos, divididos en cinco pabellones, un total de ciento cuarenta y siete células. Mediante la observación sistemática y la entrevista cualitativa s semi-estructurada como las principales fuentes de recopilación de datos, hemos tratado de explicar el universo que acabamos de analizar por las Ciencias Sociales. Nos dimos cuenta de que, para cumplir con la escena nacional, regaliz viola de manera flagrante lo que se denomina en la Constitución de 1988 y LEP (Ley de Ejecución Penal), sin tener en cuenta los derechos de los individuos a una porción de una oración con un mínimo de dignidad. Se ha demostrado que las personas que permean el universo proviene de un ambiente de la prisión, la sociabilidad violenta, sedo también tienen un habitus precario. La prisión, espacio disciplinario y un tipo específico de interacción social marcada por el control, contribuye a la profundización de habitus, pero que muestra que no es también como un espacio cerrado en absoluto, sino un lugar donde penetran las redes y dinámicas muy social. Al mismo tiempo, se encontró que más de la presencia de "grupos organizados" es el espacio en las cárceles para la interacción social y las redes sociales que pasan dentro y fuera de su espacio

Desenvolvimento de métodos construtivos e de novos materiais empregados na confecção de cartuchos de próteses de membros inferiores

The manufacture of prostheses for lower limb amputees (transfemural and transtibial) requires the preparation of a cartridge with appropriate and custom fit to the profile of each patient. The traditional process to the patients, mainly in public hospitals in Brazil, begins with the completion of a form where types of equipment, plugins, measures, levels of amputation etc. are identified. Currently, such work is carried out manually using a common metric tape and caliper of wood to take the measures of the stump, featuring a very rudimentary, and with a high degree of uncertainty geometry of the final product. To address this problem, it was necessary to act in two simultaneously and correlated directions. Originally, it was developed an integrated tool for viewing 3D CAD for transfemoral types of prostheses and transtibial called OrtoCAD I. At the same time, it was necessary to design and build a reader Mechanical equipment (sort of three-dimensional scanner simplified) able to obtain, automatically and with accuracy, the geometric information of either of the stump or the healthy leg. The methodology includes the application of concepts of reverse engineering to computationally generate the representation of the stump and/or the reverse image of the healthy member. The materials used in the manufacturing of prostheses nor always obey to a technical scientific criteria, because, if by one way it meets the criteria of resistance, by the other, it brings serious problems mainly due to excess of weight. This causes to the user various disorders due to lack of conformity. That problem was addressed with the creation of a hybrid composite material for the manufacture of cartridges of prostheses. Using the Reader Fitter and OrtoCAD, the new composite material, which aggregates the mechanical properties of strength and rigidity on important parameters such as low weight and low cost, it can be defined in its better way. Besides, it brings a reduction of up steps in the current processes of manufacturing or even the feasibility of using new processes, in the industries, in order to obtain the prostheses. In this sense, the hybridization of the composite with the combination of natural and synthetic fibers can be a viable solution to the challenges offered above

A engenharia simultânea e o perfil da indústria de confecção da grande Natal/RN utilizando as ferramentas CAD/PDM e ERP

This work presents the research carried through in the industrial segment of confection of clothes of the Great Natal whose objective is to show the profile, enterprise and technological management as also the use of simultaneous engineering in the development of products. The research approaches two studies. The first one presents the current picture of the companies, synthesized through twelve variable. As, through fifteen variable it shows to the level of use of Simultaneous Engineering in the Development of Products and its amplitude in relation to the Integrated Management using tools CAD, PDM and ERP (Computer Aided Design, Product Management Date, Enterprise Resource Planning). The integration of these systems acts aiming the reduction of the cost and the development time of products. The reached results indicate that simultaneous engineering is a competitive advantage and becomes possible: to reduce the life cycle of the product, to rationalize the resources, to incorporate one high standard of the quality to the process and product as well as to personalize the product to take care of the global market. It is important to note that this work also is considered to contribute for the better understanding of the real companies situation of confection located at the Great Natal and its role in the economy of the State of the Rio Grande do Norte

Por trás das grades :reflexões sobre a experiência do ser apenado na situação de privação de liberdade

This research has resulted of investigations appeared from our work experience as psychologist in a prison of the state Rio Grande do Norte. It deals with the meeting with prisoner in the search for the rescue of the human being dignity, discovering the being that finds annulled by backwards of the prison. The current debate on the prisoners in Brazil has as focus the creation of efficient strategies in the combat to the criminal acts, not being worried in understanding the historical and social conditions in the context in which such acts develop. Our objective was to reach an understanding of the experience of the prisoner in the situation of freedom deprivation in Natal (RN) city. Its significant social relevance meets in emphasized thematic which intends to be revealing of the not-said one of these citizens. The epistemological space and the vision of adopted human being support in the humanist ideas of the Centered Approach in the Person and construct self, central nucleus of the personality theory proposal by Carl Rogers. We opt to the phenomenological method as way of access to the singularity of the experience of each one of the participants, supporting us in the strategy of the narrative as expression of the lived world. The results had pointed that the investigated experience is through suffering, that is, the way to be in the world of prisoner in the situation of freedom deprivation is felt by him/her as difficult to support. This reality is had by him/her as difficult to control, having a negative emotional repercussion for the self, leading the citizen to the alienation of his/her existential flow in these circumstances. The reflections produced in this work take us to consider that the punishment practices on behalf of a normalization of the behavior, linked to the recovery idea, do not meet to the intention of the arrests, that come demonstrating to the inefficacy of the objectives shown in the law as well as the loss of the human being dignity

Confecção e caracterização físico-química de filmes compósitos autossustentáveis NaAlg-TiO2-WO3

A new self-sustainable film was prepared through the sol-gel modified method, previously employed in our research group; sodium alginate was used as the polymer matrix, along with plasticizer glycerol, doped with titanium dioxide (TiO2) and tungsten trioxide (WO3). By varying WO3 concentration (0,8, 1,6, 2,4 and 3,2 μmol) and keeping TiO2 concentration constant (059 mmol), it was possible to study the contribution of these oxides on the obtained films morphological and electrical properties. Self-sustainable films have analyzed by Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XDR), Scanning Electron Microscope (SEM), Energy Dispersive X-ray Spectroscopy (EDS) and Electrochemical Impedance Spectroscopy (EIS). By the IR specters, it was possible identify the TiO2, and posteriorly WO3, addition has provided dislocation of alginate characteristics bands to smaller vibrations frequencies indicating an electrostatic interaction between the oxides and the polymer matrix. Diffractograms show predominance of the amorphous phase in the films. SEM, along with EDX, analysis revealed self-sustainable films showed surface with no cracks and relative dispersion of the oxides throughout the polymer matrix. From Impedance analysis, it was observe increasing WO3 concentration to 2,4 μmol provided a reduction of films resistive properties and consequent improvement of conductive properties

Análise de tensões integrada a sistema de engenharia reversa para projeto e confecção de próteses

This work consists of the conception, developing and implementation of a Computational Routine CAE which has algorithms suitable for the tension and deformation analysis. The system was integrated to an academic software named as OrtoCAD. The expansion algorithms for the interface CAE genereated by this work were developed in FORTRAN with the objective of increase the applications of two former works of PPGEM-UFRN: project and fabrication of a Electromechanincal reader and Software OrtoCAD. The software OrtoCAD is an interface that, orinally, includes the visualization of prothetic cartridges from the data obtained from a electromechanical reader (LEM). The LEM is basically a tridimensional scanner based on reverse engineering. First, the geometry of a residual limb (i.e., the remaining part of an amputee leg wherein the prothesis is fixed) is obtained from the data generated by LEM by the use of Reverse Engineering concepts. The proposed core FEA uses the Shell's Theory where a 2D surface is generated from a 3D piece form OrtoCAD. The shell's analysis program uses the well-known Finite Elements Method to describe the geometry and the behavior of the material. The program is based square-based Lagragean elements of nine nodes and displacement field of higher order to a better description of the tension field in the thickness. As a result, the new FEA routine provide excellent advantages by providing new features to OrtoCAD: independency of high cost commercial softwares; new routines were added to the OrtoCAD library for more realistic problems by using criteria of fault engineering of composites materials; enhanced the performance of the FEA analysis by using a specific grid element for a higher number of nodes; and finally, it has the advantage of open-source project and offering customized intrinsic versatility and wide possibilities of editing and/or optimization that may be necessary in the future

A injunção em livros didáticos de língua portuguesa do 4º e 5º anos do ensino fundamental

This investigation aims at identifying, describing, analyzing and interpreting how textbooks on Portuguese Language approach, beginning with the linguistic material, the effects of sense in texts that predominately employ injunctives. The corpus of this study is comprised of six collections of textbooks on Portuguese Language, which are part of the National Program Guide for Textbooks (PNLD) from 2010, adopted by the public schools in the city of Natal and the object of study for the Read/Tell Project of the Educational Observatory of the Federal University of Rio Grande do Norte (UFRN). Textbooks from the 4th and 5th grades, Elementary School, were analyzed – 12 copies total. For the analysis, we selected 16 writing proposals of injunctive texts. Our study is based on theoretical discussions by Adam (2001a, 2001b) with regard to the genre of: inciting to action. In addition, we consider the work of Koch and Fávero (1987), Koch and Elias (2009), Marcuschi (2003, 2008) Pery-Woodly (2001), Rodrigues (2013), Travaglia (1992, 2007) and Rosa (2007). With respect to discussions on textbooks, we refer to Choppin (2004, 2009), Batista (2003, 2009), Rojo e Batista (2005), and with regard to Portuguese Language textbooks specifically, we consider Soares (1998, 2001, 2004) and Bunzen and Rojo (2005). The proposals for writing in injunctive texts, in the collections analyzed, are tips/recommendations, instructions on making toys and/or games, travel itineraries and cooking recipes, such that 69% of them appear in the 4 th grade textbooks and only 31% appear in the 5th grade textbooks. With respect to the linguistic elements responsible for the construction of directive speech acts and the effects on sense produced by them, the data shows that 50% of the writing proposals do not exploit linguistic categories that implicate the effects on sense using injunctives, or rather, there is no work done dealing with linguistic analysis, while 33% mention the imperative mode and 17% investigate infinitive verbs. In this dissertation, the textual plans of incitation to act genres were studied and in them the linguistic materiality that vehicles injunction. This study might contribute to the improvement of Portuguese language teaching in what concerns the articulation of grammatical studies to textual sequences/types, mainly in the case of Portuguese language textbooks for the 4th and 5th grades of Elementary School.

Utilização do titâneo na confecção de estruturas metálicas em prótese parcial removível

Due to properties such as excellent biocompatibility, high resistance to corrosion and low specific weight, titanium has been considered a material of great interest for Dentistry. It has been widely used in implants and orthognathic surgeries. Recently, titanium has been seen as a feasible alternative for the fabrication of removable partial denture frameworks, either in pure titanium (99.75%) or in titanium alloy forms (Ti-6Al-4V; Ti-6A1-7Nb). Based on a review of the literature, this work studied the use of titanium for the fabrication of removable partial denture frameworks, focusing on its advantages and disadvantages as well as its characteristics. It was concluded that the use of titanium is a convenient option for partially edentulous arches rehabilitation with quite satisfactory and promising clinical results. However, the need for highly-equipped laboratories increases the cost, preventing its large scale use.

Utilização do titâneo na confecção de estruturas metálicas em prótese parcial removível

Due to properties such as excellent biocompatibility, high resistance to corrosion and low specific weight, titanium has been considered a material of great interest for Dentistry. It has been widely used in implants and orthognathic surgeries. Recently, titanium has been seen as a feasible alternative for the fabrication of removable partial denture frameworks, either in pure titanium (99.75%) or in titanium alloy forms (Ti-6Al-4V; Ti-6A1-7Nb). Based on a review of the literature, this work studied the use of titanium for the fabrication of removable partial denture frameworks, focusing on its advantages and disadvantages as well as its characteristics. It was concluded that the use of titanium is a convenient option for partially edentulous arches rehabilitation with quite satisfactory and promising clinical results. However, the need for highly-equipped laboratories increases the cost, preventing its large scale use.

Protocolo clínico para confecção de próteses removíveis

Este protocolo objetiva esclarecer dúvidas existentes a respeito dos passos necessários para a reabilitação com próteses totais e parciais removíveis convencionais. Essas alternativas de tratamento são modalidades terapêuticas consagradas na literatura e podem devolver função mastigatória, estética, fonação e conforto ao paciente quando confeccionadas de maneira satisfatória. Elas representam também uma ótima opção para aqueles pacientes que não podem se submeter ao tratamento com implantes, por apresentarem limitações biológicas ou financeiras. A abordagem do protocolo clínico está dividida em duas partes. A primeira parte ilustra a reabilitação com próteses totais convencionais e a segunda, a reabilitação com próteses parciais removíveis convencionais em arcos inferiores com extremidade livre bilateral. Por meio da demonstração do passo a passo com fotos, dicas clínicas e resumos sistemáticos do conteúdo teórico contido nesse material, o aluno de Odontologia e o cirurgião-dentista poderão conhecer os passos necessários para executar estes tipos de reabilitações, desde o momento clínico de diagnóstico até o de controle e manutenção. Esperamos que essa obra desperte o interesse dos cirurgiões-dentistas por executar esses tipos de próteses e que os ajude a desenvolverem práticas e habilidades que melhorem o desempenho clínico dessas alternativas de tratamento.

Protocolo clínico para confecção de próteses removíveis

Este protocolo objetiva esclarecer dúvidas existentes a respeito dos passos necessários para a reabilitação com próteses totais e parciais removíveis convencionais. Essas alternativas de tratamento são modalidades terapêuticas consagradas na literatura e podem devolver função mastigatória, estética, fonação e conforto ao paciente quando confeccionadas de maneira satisfatória. Elas representam também uma ótima opção para aqueles pacientes que não podem se submeter ao tratamento com implantes, por apresentarem limitações biológicas ou financeiras. A abordagem do protocolo clínico está dividida em duas partes. A primeira parte ilustra a reabilitação com próteses totais convencionais e a segunda, a reabilitação com próteses parciais removíveis convencionais em arcos inferiores com extremidade livre bilateral. Por meio da demonstração do passo a passo com fotos, dicas clínicas e resumos sistemáticos do conteúdo teórico contido nesse material, o aluno de Odontologia e o cirurgião-dentista poderão conhecer os passos necessários para executar estes tipos de reabilitações, desde o momento clínico de diagnóstico até o de controle e manutenção. Esperamos que essa obra desperte o interesse dos cirurgiões-dentistas por executar esses tipos de próteses e que os ajude a desenvolverem práticas e habilidades que melhorem o desempenho clínico dessas alternativas de tratamento.

Estruturas cerâmicas a base de zircônia e alumina utilizadas na confecção de infra - estruturas para coroas e pontes fixas

The continuous advances in ceramic systems for crowns and bridges infrastructure getting researchers and manufacturers looking for a material that has good mechanical properties and aesthetic. The purpose of this study was to verify in which composition and sintering temperature the ceramic system for infrastructure composed of alumina and zirconia would have the best mechanical properties. With this objective we made in UFRN laboratories 45 test bodies in the form of rectangular bars with the following dimensions: 30mm x 8mm x 3mm, where we separated by the sintering temperature: 1200°C, 1300ºC and 1400ºC, and by comp osition: 33% Zirconia + 67% Alumina; 50% Zirconia + 50% Alumina and 25% Zirconia + 75% Alumina, these test bodies were not infiltrated with glass. Also, were made nine test bodies by a technical from a laboratory with a commercial ceramic system: in the Ceram Zircônia (Vita - Zahnfabrik) with the following dimensions: 20mm x 10mm x 0.5mm, these test bodies following all recommendations of the manufacturer and were infiltrated with glass. Were realized optical and electronic microscopy analyses, hardness testing, resistance to bending in three points, porosity and bulk density. After analysis of the results we verified that with the increasing of sintering temperature, increased the value of resistance to bending, but with the same temperature there was no significant difference between the different compositions, samples made with the commercial ceramic that were infiltrated, presented a resistance to bending six times greater than the samples sintered to 1400°C and which have not been infiltra ted. There was no significant difference between the values of apparent porosity for the samples made in UFRN laboratories, but the samples of commercial ceramic obtained 0% in porosity apparent value. In tests of Rockwell Hardness there is an increase in the value of Hardness, with the increase of sintering temperature for the samples not infiltrated. Samples infiltrated showed similar values as the samples sintered in 1400°C. There was no significant difference between the values of apparent density among samples manufactured in UFRN laboratories and samples made with a commercial ceramic