Influência da vermiculita expandida na resistência à compressão e reologia de pastas cimentantes de poços de petróleo

Several problems related to the loss of hydraulic seal in oilwells, causing gas migration and/or contamination of the production zone by water, have been reported. The loss of the hydraulic seal is a consequence of cracks which can be occasioned either by the invasion of gas during the wait on cement or by the expansion of the casing causing the fracture of the cement sheath. In case of the pressure of the formation is higher than the pressure in the annulus, gas can migrate into the slurry and form microannulus, which are channels where gas migrates after the cement is set. Cracks can be also occasioned by the fracture of the cement sheath when it does not withstand the thermal and dynamic loads. In reservoirs where the oil is heavy, steam water injection operation is required in order to get the oil flowing. This operation increases the temperature of the casing, and then it expands and causes the fracture of the cement sheath in the annulus. When the failures on the cement are detected, remedial cementing is required, which raise costs caused by the interventions. Once the use of cement in the construction civil sector is older than its use in the petroleum sector, it is common to bring technologies and solutions from the civil construction and apply them on the petroleum area. In this context, vermiculite, a mineral-clay widely encountered in Brazil, has been used, on its exfoliated form, in the civil construction, especially on the manufacture of lights and fireproof concretes with excellent thermal and acoustical properties. It has already been reported in scientific journals, studies of the addition of exfoliated vermiculite in Portland cements revealing good properties related to oilwell cementing operations. Thus, this study aimed to study the rheological behavior, thickening time, stability and compressive strength of the slurries made of Portland cement and exfoliated vermiculite in 5 different compositions, at room temperature and heated. The results showed that the compressive strength decreased with the addition of exfoliated vermiculite, however the values are still allowed for oiwell cementing operations. The thickening time of the slurry with no exfoliated vermiculite was 120 min and the thickening time of the slurry with 12 % of exfoliated vermiculite was 98 min. The stability and the rheological behavior of the slurries revealed that the exfoliated vermiculite absorbed water and therefore increased the viscosity of the slurries, even though increasing the factor cement-water. The stability experiment carried out at 133 ºF showed that, there was neither sedimentation nor reduction of the volume of the cement for the slurry with 12 % of exfoliated vermiculite. Thus, the addition of exfoliated vermiculite accelerates the set time of the cement and gives it a small shrinkage during the wait on cement, which are important to prevent gas migration

Compressão de Imagens Usando a Função de Peano e a Transformada Wavelet 1D

In this work, spoke about the importance of image compression for the industry, it is known that processing and image storage is always a challenge in petrobrás to optimize the storage time and store a maximum number of images and data. We present an interactive system for processing and storing images in the wavelet domain and an interface for digital image processing. The proposal is based on the Peano function and wavelet transform in 1D. The storage system aims to optimize the computational space, both for storage and for transmission of images. Being necessary to the application of the Peano function to linearize the images and the 1D wavelet transform to decompose it. These applications allow you to extract relevant information for the storage of an image with a lower computational cost and with a very small margin of error when comparing the images, original and processed, ie, there is little loss of quality when applying the processing system presented . The results obtained from the information extracted from the images are displayed in a graphical interface. It is through the graphical user interface that the user uses the files to view and analyze the results of the programs directly on the computer screen without the worry of dealing with the source code. The graphical user interface, programs for image processing via Peano Function and Wavelet Transform 1D, were developed in Java language, allowing a direct exchange of information between them and the user

Estudo de concretos de diferentes resistências à compressão submetidos a altas temperaturas sem e com incorporação de fibras de politereftalato de etileno (PET)

The reinforced concrete structures are largely used in buildings worldwide. Upon the occurrence of fire in buildings, there is a consensus among researchers that the concrete has a high resistance to fire, due mainly to its low thermal conductivity. However, this does not mean that this material is not affected by exposure to high temperatures. Reduction of the compressive strength, modulus of elasticity, discoloration and cracking, are some of the effects caused by thermal exposure. In the case of concretes with higher resistance occurs even desplacamentos explosives, exposing the reinforcement to fire and contributing to reducing the support capacity of the structural element. Considering the above, this study aims to examine how the compressive strength and porosity of concrete are affected when subjected to high temperatures. Were evaluated concrete of different resistances, and even was the verified if addition fibers of polyethylene terephthalate (PET) in concrete can be used as an alternative to preventing spalling. The results indicated that explosive spalling affect not only high strength concrete whose values of this study ranged from 70 to 88 MPa, as well as conventional concrete of medium strength (52 MPa) and the temperature range to which the concrete begins to suffer significant changes in their resistance is between 400 º C and 600 º C, showing to 600 º C a porosity up to 188% greater than the room temperature

Algoritmo SOM com estrutura hierárquica e dinâmica aplicado a compressão de imagens

ln this work the implementation of the SOM (Self Organizing Maps) algorithm or Kohonen neural network is presented in the form of hierarchical structures, applied to the compression of images. The main objective of this approach is to develop an Hierarchical SOM algorithm with static structure and another one with dynamic structure to generate codebooks (books of codes) in the process of the image Vector Quantization (VQ), reducing the time of processing and obtaining a good rate of compression of images with a minimum degradation of the quality in relation to the original image. Both self-organizing neural networks developed here, were denominated HSOM, for static case, and DHSOM, for the dynamic case. ln the first form, the hierarchical structure is previously defined and in the later this structure grows in an automatic way in agreement with heuristic rules that explore the data of the training group without use of external parameters. For the network, the heuristic mIes determine the dynamics of growth, the pruning of ramifications criteria, the flexibility and the size of children maps. The LBO (Linde-Buzo-Oray) algorithm or K-means, one ofthe more used algorithms to develop codebook for Vector Quantization, was used together with the algorithm of Kohonen in its basic form, that is, not hierarchical, as a reference to compare the performance of the algorithms here proposed. A performance analysis between the two hierarchical structures is also accomplished in this work. The efficiency of the proposed processing is verified by the reduction in the complexity computational compared to the traditional algorithms, as well as, through the quantitative analysis of the images reconstructed in function of the parameters: (PSNR) peak signal-to-noise ratio and (MSE) medium squared error

Compressão auto-adaptativa de imagens coloridas

Image compress consists in represent by small amount of data, without loss a visual quality. Data compression is important when large images are used, for example satellite image. Full color digital images typically use 24 bits to specify the color of each pixel of the Images with 8 bits for each of the primary components, red, green and blue (RGB). Compress an image with three or more bands (multispectral) is fundamental to reduce the transmission time, process time and record time. Because many applications need images, that compression image data is important: medical image, satellite image, sensor etc. In this work a new compression color images method is proposed. This method is based in measure of information of each band. This technique is called by Self-Adaptive Compression (S.A.C.) and each band of image is compressed with a different threshold, for preserve information with better result. SAC do a large compression in large redundancy bands, that is, lower information and soft compression to bands with bigger amount of information. Two image transforms are used in this technique: Discrete Cosine Transform (DCT) and Principal Component Analysis (PCA). Primary step is convert data to new bands without relationship, with PCA. Later Apply DCT in each band. Data Loss is doing when a threshold discarding any coefficients. This threshold is calculated with two elements: PCA result and a parameter user. Parameters user define a compression tax. The system produce three different thresholds, one to each band of image, that is proportional of amount information. For image reconstruction is realized DCT and PCA inverse. SAC was compared with JPEG (Joint Photographic Experts Group) standard and YIQ compression and better results are obtain, in MSE (Mean Square Root). Tests shown that SAC has better quality in hard compressions. With two advantages: (a) like is adaptive is sensible to image type, that is, presents good results to divers images kinds (synthetic, landscapes, people etc., and, (b) it need only one parameters user, that is, just letter human intervention is required

Compressão Seletiva de Imagens Coloridas com Detecção Automática de Regiões de Interesse

There has been an increasing tendency on the use of selective image compression, since several applications make use of digital images and the loss of information in certain regions is not allowed in some cases. However, there are applications in which these images are captured and stored automatically making it impossible to the user to select the regions of interest to be compressed in a lossless manner. A possible solution for this matter would be the automatic selection of these regions, a very difficult problem to solve in general cases. Nevertheless, it is possible to use intelligent techniques to detect these regions in specific cases. This work proposes a selective color image compression method in which regions of interest, previously chosen, are compressed in a lossless manner. This method uses the wavelet transform to decorrelate the pixels of the image, competitive neural network to make a vectorial quantization, mathematical morphology, and Huffman adaptive coding. There are two options for automatic detection in addition to the manual one: a method of texture segmentation, in which the highest frequency texture is selected to be the region of interest, and a new face detection method where the region of the face will be lossless compressed. The results show that both can be successfully used with the compression method, giving the map of the region of interest as an input

Capacidade de absorção de energia de tubos de compósitos submetidos à compressão

Structures capable of absorbing large amounts of energy are of great interest, particularly for the automotive and aviation industries, to reduce tbe impact on passengers in the case of a collision. The energy absorption properties of composite materials structures can be tailored, thus making these structures an appealing option a substitute of more traditional structures in applications where energy absorption is crucial. ln this research, the influence of some parameters, which affect the energy absorption capacity of composite material tubes, was investigated. The tubes were fabricated by hand lay-up, using orthophthalic polyester resin and a plain weave E-glass fabric Test specimens were prepared and tested under compression load. The ínfluence of the following parameters on the specific energy absorption capacity of the tubes was studied: fiber configuration (0/90º or ± 45°), tube cross-section (circular or square), and processing conditions (with or without vacuum). The results indicated that circular cross-section tubes with fibers oriented at 0/90º presented the highest level of specific energy absorbed. Further, specimens from tubes fabricated under vacuum displayed higher energy absorption capacity, when compared with specimens from tubes fabricated without vacuum. Thus, it can be concluded that the fabrication process with vacuum produce composite structures with better energy absorption capacity

Análise teórico-experimental do coeficiente de perfomance (COP) de um sistema de refrigeração por jato-compressão

The use of waste heat of energy conversion equipment to produce a cooling effect, consists currently in a very interesting way of efficiency improvement of energy systems. The present research has as intention the theoretical and experimental study of a new intermittent refrigeration system ejector cycle characteristics, with use of waste heat. Initially, was doing a bibliographical survey about the vapor ejector refrigeration system technology. In the following stage was doing a simulation of the corresponding thermodynamic cycle, with preliminarily intention to evaluate the performance of the system for different refrigerants fluids. On the basis of the results of the simulation were selected the refrigerant fluid and developed an experimental group of benches of the refrigeration system considered, where pressure and temperature sensory had been inserted in strategical points of the refrigeration archetype and connected to a computerized data acquisition system for measure the refrigerant fluid properties in the thermodynamic cycle. The test results obtained show good agreement with the literature

Efeitos imediatos da eletroestimulação nervosa transcutânea e crioterapia na espasticidade e na atividade eletromiográfica de sujeitos hemiparéticos

Cerebrovascular accident (CVA) is a term used to characterize an ischemic or hemorrhagic vascular injury, which has got as main clinic manifestations, the motor and reflex function disturbance. In the first stage there is flaccidity and loss of voluntary movements that afterwards is substituted by mass patterns and spasticity. The spasticity brings with itself functional deficits and can generate negative impacts in various motor patterns. The aim of this research was to investigate the hyperreflexia and identify the immediate effects of transcutaneous nervous stimulation (TENS) and cryotherapy in the spasticity and electromyographic activity of hemiparetic subjects. The study is characterized as an almost experimental type, in which were selected, to compose the sample, 16 patients of both sex with CVA sequel. These individuals were evaluated by collecting the amplitude peak to peak and H reflex latency, Motor response (M response) in solear muscle and the electromyography (EMG) of the injured and healthy legs anterior tibial muscles. In the injured limb the evaluations occurred in different days for cryotherapy, TENS and control, in two moments, before and after the interventions. The healthy limb was evaluated one single time to serve as baseline, for comparison with the injured limb. It was used an statistic analysis, the t paired student test to identify the H reflex differences, latency and EMG of the injured and healthy limbs and to compare the results before and after the recourses application. The ANOVA for related samples was used to identify the differences among the recourses used. It was attributed for the statistic tests a significance level of 5%. The amplitude peak to peak of normalized maximum H reflex through the maximum motor response (Hmax/Mmax), showed itself significantly increased in the injured limb (p=0.0245). The H reflex latency was presented reduced in the injured limb (p=0, 0375). The electromyographic activity was showed decreased in the injured limb (p< 0.0001). After the TENS there was a Hmáx/Mmáx ratio decrease (0.60±0.16 versus 0.49.±0.18; P = 0.0006). Nonetheless, Just after the cryotherapy application there was an increase of Hmáx/Mmáx ratio (0.58 ± 0,15 to 0.77 ± 0.13, P=0,0007) and increase of signal latency (30.41 ± 1.87 versus 33.24 ± 2.19; P=0.0001). The electromyographic activity wasn t altered significantly by any resource. It was met statistic significant differences when the Hmáx/Mmáx P<0.0001) ratio and H reflex latency (P<0.0001) were compared between the post TENS, cryotherapy and control. One can conclude that the TENS can be used to spasticity immediate reduction, and that the cryotherapy can increase the hyperreflexia state in spastic patients. Nonetheless, the spasticity decrease or increase didn t provoke lectromyographic activity change in the muscle that is opponent to the spastic one

Avaliação da eficiência da técnica de obturação pela compressão hidrùlica vertical após instrumentação automatizada

The purpose of this study was to evaluate through radiographic and microscopic analysis the efficiency of the filling techniques by vertical hidraulic compression after the root canal mechanical instrumentation in vitro as well to evaluate the marginal apical leakage through macroscopic and microscopic analysis. Thirty human mandibular molars were used , they were divided on three groups, these were subdivided on six subgroups with five specimens each, come down to 106 root canals filled. Initially, the teeth were instrumented with Profile system series 29 and filled with two ways: single accessory cone or single cone associated with gutta-percha secundary cone, with Fill Canal sealer or Sealer 26. Completed the filling, the teeth were coated with araldit and finger -nail polish except for the apical 2 mm and dried for 3 hours, thep radiographs were taken of the teeth in orto and disto-radiai directions. Next, the coronal seal was carried out with composite resin photopolymerized and with their process of making impermeable. Teeth of positive controls were used without araldit and finger-nail polish whereas the negative controls were used with total coat of araldit and finger-nail polish. The specimens were placed in 2% Methylene Blue dye for 24 hours and thermocycled for 7 days. Afterwards, sections were made of each tooth at mesial and distal roat, after this the teeth were radiographed at buccolíngual direction for a macroscopic analysis and at buccolingual and mesiodistal directions for assessment of the marginal apical leakage. Cross sections were made 3 mm to 3mm since the tooth apice. The sections obtained for each group were observed with a stereomicroscope to evaluate the quality of the root canal filling and the marginal apical leakage. The results showed that: In the four techniques the marginal dye leakage was present in the apical third; in all groups the quality of the root canal filling in the radiography was better at mesial root canal and the single cone technique showed inefficient when only a single distal root canal was present. In the radiographic evaluation the best quality of the root canal filling was observed in the 1A group (single accessory cone + FiIl Canal), as in the mesial root as in the distal root wich Shcwed twe root canals: when the distaI root had only one canal. the best result was showed by 28 group (single accessory cone associated with secundary cone + Fill Canal) In the macroscopic analysis of longitudinal !eaKage (outside surface). less leakage was showed as In the mesial root as in the distal root in the negative control group (3) followed 2A group (single accessory cone + Sealer 26). When the microscopic analysis of tranversal leakage of both roots (inside surface) was carried out. the groups that showed less dye leakage were the negative control (38) followed the 28 group (single acessory cone associated with secundary cone + Sealer 26). The homogeneity o filling was best noted in the 1 A group (.single accessoty cone + Fill Canal). The groups that showed less dye penetration in the tranversal leakage (total area) were negative control (3B) and 2B

Investigando a compressão da percepção de distância em ambientes virtuais através da comparação entre dispositivos de visualização

The correct distance perception is important for executing various interactive tasks such as navigation, selection and manipulation. It is known, however, that, in general, there is a significant distance perception compression in virtual environments, mainly when using Head-Mounted Displays - HMDs. This perceived distance compression may bring various problems to the applications and even affect in a negative way the utility of those applications that depends on the correct judgment of distances. The scientific community, so far, have not been able to determine the causes of the distance perception compression in virtual environments. For this reason, it was the objective of this work to investigate, through experiments with users, the influence of both the field-of-view - FoV - and the distance estimation methods on this perceived compression. For that, an experimental comparison between the my3D device and a HMD, using 32 participants, seeking to find information on the causes of the compressed perception, was executed. The results showed that the my3D has inferior capabilities when compared to the HMD, resulting in worst estimations, on average, in both the tested estimation methods. The causes of that are believed to be the incorrect stimulus of the peripheral vision of the user, the smaller FoV and the smaller immersion sense, as described by the participants of the experiment.

Análise de desempenho de algoritmos de compressão de dados com perda para aplicações industriais

The great amount of data generated as the result of the automation and process supervision in industry implies in two problems: a big demand of storage in discs and the difficulty in streaming this data through a telecommunications link. The lossy data compression algorithms were born in the 90’s with the goal of solving these problems and, by consequence, industries started to use those algorithms in industrial supervision systems to compress data in real time. These algorithms were projected to eliminate redundant and undesired information in a efficient and simple way. However, those algorithms parameters must be set for each process variable, becoming impracticable to configure this parameters for each variable in case of systems that monitor thousands of them. In that context, this paper propose the algorithm Adaptive Swinging Door Trending that consists in a adaptation of the Swinging Door Trending, as this main parameters are adjusted dynamically by the analysis of the signal tendencies in real time. It’s also proposed a comparative analysis of performance in lossy data compression algorithms applied on time series process variables and dynamometer cards. The algorithms used to compare were the piecewise linear and the transforms.

“Oi, meu nome é Ana” - um estudo fenomenológico-existencial da experiência de mulheres com anorexia nervosa

This research deals with anorexia nervosa through the look of those who lived this experience. Eating Disorders have been presented as psychopathology increasingly recurrent in contemporary, being almost doubled incidence in the last 20 years, reaching mainly teenagers and bringing consequences and implications of various kinds. The literature points to the relevance of the current ideal of beauty, in which thinness is overvalued. In this case, the study’s objective was to understand, from an existential-phenomenological perspective, anorexia experience. Thus, when assessing the experience, seeking to understand the possible directions that the non-eating is for the person who lives such an experience. The study, of Heidegger's existential-phenomenological inspiration, used semi-structured interviews as a means of access to the experience. Female two people were interviewed, at the age of 17 and 30, began with a starter question ("How was, or how is, your anorexia experience?"), which allowed the interviewee to talk about their experience. For the selection of the study participant was publicized among health professionals, as well as in social networks and blogs, in which the research objectives and approaches have been made explicit. The field diary was also used as a methodological resource, seeking a greater approximation of the experiences of the interviewees and the researcher. The interviews were interpreted in the by Heidegger's hermeneutics. The meanings unveiled in the narratives revealed issues beyond the physical and pathological issue, being involved family, wishes, friends, experiences, life projects. The corporal, as thought by Martin Heidegger, became very present in the statements of the interviewees, as it is part of existence. Among the Heidegger´s ideas, emphasizes care, inhospitality, live, boredom, openness to possibilities and factuality, that might be discussed from interviewees' discourse, engendering reflections about their senses, in their lives.

“Oi, meu nome é Ana” - um estudo fenomenológico-existencial da experiência de mulheres com anorexia nervosa

This research deals with anorexia nervosa through the look of those who lived this experience. Eating Disorders have been presented as psychopathology increasingly recurrent in contemporary, being almost doubled incidence in the last 20 years, reaching mainly teenagers and bringing consequences and implications of various kinds. The literature points to the relevance of the current ideal of beauty, in which thinness is overvalued. In this case, the study’s objective was to understand, from an existential-phenomenological perspective, anorexia experience. Thus, when assessing the experience, seeking to understand the possible directions that the non-eating is for the person who lives such an experience. The study, of Heidegger's existential-phenomenological inspiration, used semi-structured interviews as a means of access to the experience. Female two people were interviewed, at the age of 17 and 30, began with a starter question ("How was, or how is, your anorexia experience?"), which allowed the interviewee to talk about their experience. For the selection of the study participant was publicized among health professionals, as well as in social networks and blogs, in which the research objectives and approaches have been made explicit. The field diary was also used as a methodological resource, seeking a greater approximation of the experiences of the interviewees and the researcher. The interviews were interpreted in the by Heidegger's hermeneutics. The meanings unveiled in the narratives revealed issues beyond the physical and pathological issue, being involved family, wishes, friends, experiences, life projects. The corporal, as thought by Martin Heidegger, became very present in the statements of the interviewees, as it is part of existence. Among the Heidegger´s ideas, emphasizes care, inhospitality, live, boredom, openness to possibilities and factuality, that might be discussed from interviewees' discourse, engendering reflections about their senses, in their lives.

Influência da vermiculita expandida na resistência à compressão e reologia de pastas cimentantes de poços de petróleo

Several problems related to the loss of hydraulic seal in oilwells, causing gas migration and/or contamination of the production zone by water, have been reported. The loss of the hydraulic seal is a consequence of cracks which can be occasioned either by the invasion of gas during the wait on cement or by the expansion of the casing causing the fracture of the cement sheath. In case of the pressure of the formation is higher than the pressure in the annulus, gas can migrate into the slurry and form microannulus, which are channels where gas migrates after the cement is set. Cracks can be also occasioned by the fracture of the cement sheath when it does not withstand the thermal and dynamic loads. In reservoirs where the oil is heavy, steam water injection operation is required in order to get the oil flowing. This operation increases the temperature of the casing, and then it expands and causes the fracture of the cement sheath in the annulus. When the failures on the cement are detected, remedial cementing is required, which raise costs caused by the interventions. Once the use of cement in the construction civil sector is older than its use in the petroleum sector, it is common to bring technologies and solutions from the civil construction and apply them on the petroleum area. In this context, vermiculite, a mineral-clay widely encountered in Brazil, has been used, on its exfoliated form, in the civil construction, especially on the manufacture of lights and fireproof concretes with excellent thermal and acoustical properties. It has already been reported in scientific journals, studies of the addition of exfoliated vermiculite in Portland cements revealing good properties related to oilwell cementing operations. Thus, this study aimed to study the rheological behavior, thickening time, stability and compressive strength of the slurries made of Portland cement and exfoliated vermiculite in 5 different compositions, at room temperature and heated. The results showed that the compressive strength decreased with the addition of exfoliated vermiculite, however the values are still allowed for oiwell cementing operations. The thickening time of the slurry with no exfoliated vermiculite was 120 min and the thickening time of the slurry with 12 % of exfoliated vermiculite was 98 min. The stability and the rheological behavior of the slurries revealed that the exfoliated vermiculite absorbed water and therefore increased the viscosity of the slurries, even though increasing the factor cement-water. The stability experiment carried out at 133 ºF showed that, there was neither sedimentation nor reduction of the volume of the cement for the slurry with 12 % of exfoliated vermiculite. Thus, the addition of exfoliated vermiculite accelerates the set time of the cement and gives it a small shrinkage during the wait on cement, which are important to prevent gas migration