Avaliação da influência do nacl em pastas de cimento portland para cimentação de poços de petróleo em zonas evaporíticas

One of the major current challenges for oilwell companies is the extraction of oil from evaporitic zones, also known as pre-salt basins. Deep reservoirs are found under thick salt layers formed from the evaporation of sea water. Salt layers seal the flow of oil from underneath rock formations, which store hydrocarbons and increase the probability of success in oil and gas exploration. Oilwells are cemented using Portland-based slurries to promote mechanical stability and zonal isolation. For pre-salt oilwells, NaCl must be added to saturate the cement slurries, however, the presence of salt in the composition of slurries affects their overall behavior. Therefore, the objective of the present study was to evaluate the effect of the addition of 5 to 25% NaCl on selected properties of Portland-based slurries. A series of tests were carried out to assess the rheological behavior, thickening time, free water and ultrassonic compressive strength. In addition, the slurries were also characterized by thermal analysis, X ray diffraction and scanning electron microscopy. The results showed that the addition of NaCl affected the thickening time of the slurries. NaCl contents up to 10% shortened the thickening time of the slurries. On the other hand, concentrations in excess of 20% not only extended the thickening time, but also reduced the strength of hardened slurries. The addition of NaCl resulted in the formation of a different crystalline phase called Friedel´s salt, where free chlorine is bonded to tricalcium aluminate

Obtenção de polímeros de LCC para aplicação como antioxidante de biodiesel de soja

Biodiesel is a fuel obtained from vegetable oils, such as soy, castorbean, among others. The monoester of fatty acid of these oils have chains with mono, di and tri double connections. The presence of these insaturations are susceptible to oxidization. Antioxidants are substances able to prevent oxidization from oils, fats, fat foods, as well as esters of Alquila( biodiesel). The objective of this work is to summarize a new antioxidant from the Cashew Nut Shell Liquid (CNSL) using the electrolysis technique. A current of 2 amperes was used in a single cell of only one group and two eletrodos of stainless steel 304 in a solution of methanol, together with the eletrolits: acetic acid, sodium chloride and sodium hydroxide, for two hours of agitation. The electrolysis products are characterized by the techniques of cromatography in a thin layer, spectroscopy of infrared and gravimetric analysis. The material was submitted to tests of oxidative stability made by the techniques of spectropy of impendancy and Rancimat (EN 14112). The analyses of characterization suggest that the polimerization of the electrolytic material ocurred. The application results of these materials as antioxidants of soy biodiesel showed that the order of the oxidative stability was obtained by both techniques used

Influência da adição do NaCl e KCl em sistemas de pastas contendo sílica para poços de petróleo em zonas evaporíticas e carbonáticas

One of the major challenges faced nowadays by oil companies is the exploration of pre-salt basins. Thick salt layers were formed in remote ages as a consequence of the evaporation of sea water containing high concentrations of NaCl and KCl. Deep reservoirs can be found below salt formations that prevent the outflow of oil, thus improving the success in oil prospection. The slurries used in the cement operations of salt layers must be adequate to the properties of those specific formations. At the same time, their resulting properties are highly affected by the contamination of salt in the fresh state. It is t herefore important to address the effects of the presence of salt in the cement slurries in order to assure that the well sheath is able to fulfill its main role to provide zonal isolation and mechanical stability. In this scenario, the objective of the present thesis work was to evaluate the effect of the presence of NaCl and KCl premixed with cement and 40% silica flour on the behavior of cement slurries. Their effect in the presence of CO2 was also investigated. The rheological behavior of slurries containing NaCl and KCl was evaluated along with their mechanical strength. Thermal and microstructural tests were also carried out. The results revealed that the presence of NaCl and KCl affected the pozzolanic activity of silica flour, reducing the strength of the hardened slurries containing salt. Friedel´s salt was formed as a result of the bonding between free Cl- and tricalcium aluminate. The presence of CO2 also contributed to the degradation of the slurries as a result of a process of carbonation/bicarbonataion

Influência da substituição de areia natural por pó de pedra no comportamento mecânico, microestrutural e eletroquímico de concretos

The construction industry is one of the largest consumers of natural raw materials, and concrete is considered today the most used material wide. This accentuated consumption of natural resources has generated concern with the preservation of the environment, and has motivated various studies related to the use of resid ues, which can partially or entirely substitute, with satisfactory performance, some materials such as the aggregate, and in so doing, decrease the impact on the environment caused by the produced residues. Research has been done to better understand and improve the microstructure of concrete, as well as to understand the mechanism of corrosion in reinforced steel. In this context, this work was developed aiming at discovering the influence of the substitution of natural sand by artificial sand, with rega rd to mechanical resistance, microstructure, and durability. To obtain the electrochemical parameters, an adaptation was made to the galvanostatic electrochemical method to study the corrosion in reinforced steel. Concretes of categories 20 MPa and 40 MPa were produced, containing natural sand, and concretes of the same categories were produced with artificial sand substituting the natural sand, and with the addition of sodium nitrate and sodium chloride. Due to the use of rock dust reject (artificial sand), an evaluation was made of its environmental risk. The results indicate that the concretes of category 20 MPa present a better performance than the concrete made with natural sand, thus making it a viable substitute. For the category 40 MPa, the better performance is from the concrete containing natural sand. The adaptation of the galvanostatic electrochemical technique to the study of the corrosion of reinforced steel within concrete proved to be valid for obtaining electrochemical parameters with a high degree of reliability, considering the number of degrees of freedom

Avaliação de efeitos de um extrato aquoso de cinnamomum zeylanicum L. na marcação de constituintes sanguíneos com tecnécio-99m e na morfologia das hemácias de ratos wistar

Radiobiocomplexes are used to obtain images in nuclear medicine and employed in basic research. Blood constituents labeled with technetium-99m (99mTc) have also been employed as radiobiocomplexes and used also experimental model for evaluation of the biological effects of natural or synthetic drugs. The analysis of the morphology and the morphometrics parameters (perimeter/área ratio) can be used to evaluate the effects of drugs upon the structure of the membrane of red blood cells. Cinnamomum zeylanicum (cinnamon) is a spice used as herbal medicine to treat diseases. The aim of this study was to evaluate the effect of in vitro and in vivo treatment with an aqueous cinnamon extract on the labeling of blood constituents with 99mTc and on the morphology of red blood cells from Wistar rats. In the in vitro treatment, isolated blood sample from animals were incubated with cinnamon extract. In the in vivo treatment, blood samples were also withdrawn from animals treated with cinnamon extract. In both cases, the radiolabeling of blood constituents was done. The morphological analysis of red blood cells was also done. As control, blood or animals treated with NaCl 0.9%. The data obtained on the labeling of blood constituents with 99mTc experiments indicated that the in vitro treatment with cinnamon extract was capable to decrease signiicantly (p<0.05) the percentage of radioactivity in cellular compartments and on the fixation of cellular and plasma proteins. These effects were not observed on the in vivo treatment. The results obtained for the morphology of red blood cells suggest that the in vitro and in vivo treatments did not alter the morphology and the perimeter/area ratio. The in vitro treatment with aqueous cinnamon extract could affect the membrane structures related with the oxidation status of the stannous ion pertechnetate ion, altering the labeling of blood constituentes with 99mTc. This study was a multidisciplinary experimental research. It was developed with the contribution of the different Departments and Services of the Hospital Universitário Pedro Ernesto of the Universidade do Estado do Rio de Janeiro

Degradação fotoquímica de hidrocarbonetos da gasolina em efluentes aquosos

Photo-oxidation processes of toxic organic compounds have been widely studied. This work seeks the application of the photo-Fenton process for the degradation of hydrocarbons in water. The gasoline found in the refinery, without additives and alcohol, was used as the model pollutant. The effects of the concentration of the following substances have been properly evaluated: hydrogen peroxide (100-200 mM), iron ions (0.5-1 mM) and sodium chloride (200 2000 ppm). The experiments were accomplished in reactor with UV lamp and in a falling film solar reactor. The photo-oxidation process was monitored by measurements of the absorption spectra, total organic carbon (TOC) and chemical oxygen demand (COD). Experimental results demonstrated that the photo-Fenton process is feasible for the treatment of wastewaters containing aliphatic hydrocarbons, inclusive in the presence of salts. These conditions are similar to the water produced by the petroleum fields, generated in the extraction and production of petroleum. A neural network model of process correlated well the observed data for the photooxidation process of hydrocarbons

Estudo da reidratação do feijão verde (Vigna unguiculata L. Walp) desidratado por micro-ondas com e sem pré-tratamento osmótico

The green bean has organoleptic and nutritional characteristics that make it an important food source in tropical regions such as the Northeast of Brazil. It is a cheap source of protein and important for nutrition of rural population contributing significantly in subsistence farming of the families from Brazil s northeast. It is consumed in entire region and together with the dry meat and other products composes the menu of typical restaurants, being characterized as an important product for economy of Northeast. The green bean is consumed freshly harvested and has short cycle, being characterized as a very perishable food, which hampers your market. The drying method is an alternative to increase the lifetime and provide a reduction volume of this product making easier your transportation and storage. However is necessary to search ways of drying which keep the product quality not only from the nutritional standpoint but also organoleptic. Some characteristics may change with the drying process such as the coloring, the rehydration capacity and the grains cooking time. The decrease of drying time or of exposure of the grains to high temperature minimizes the effects related with the product quality loss. Among the techniques used to reduce the drying time and improve some characteristics of the product, stands out the osmotic dehydration, widely used in combined processes such as the pretreatment in drying food. Currently the use of the microwaves has been considered an alternative for drying food. The microwave energy generates heat inside of materials processed and the heating is practically instantaneous, resulting in shorter processing times and product quality higher to that obtained by conventional methods. Considering the importance of the green beans for the Northeast region, the wastefulness of production due to seasonality of the crop and your high perishability, the proposal of this thesis is the study of drying grain by microwaves with and without osmotic pretreatment, focusing on the search of conditions of processes which favor the rehydration of the product preserving your organoleptic characteristics. Based on the analysis of the results of osmotic dehydration and dielectric properties was defined the operating condition to be used in pretreatment of the green bean, with osmotic concentration in saline solution containing 12,5% of sodium chloride, at 40°C for 20 minutes. The drying of green bean by microwave was performed with and without osmotic pretreatment on the optimized condition. The osmotic predehydration favored the additional drying, reducing the process time. The rehydration of dehydrated green bean with and without osmotic pretreatment was accomplished in different temperature conditions and immersion time according to a factorial design 22, with 3 repetitions at the central point. According to results the better condition was obtained with the osmotically pretreated bean and rehydrated at a temperature of 60°C for 90 minutes. Sensory analysis was performed comparing the sample of the green bean in natura and rehydrated in optimized conditions, with and without osmotic pretreatment. All samples showed a good acceptance rate regarding the analyzed attributes (appearance, texture, color, odor and taste), with all values above 70%. Is possible conclude that the drying of green bean by microwave with osmotic pretreatment is feasible both in respect to technical aspects and rehydration rates and sensory quality of the product

Qualidade fisiológica de sementes de genótipos de algodoeiro sob estresse salino

The germination of cotton seeds and the seedlings emergency are generally delayed and reduced by the salinity. Although the cotton is considered a tolerant culture, it can suffer substantial reductions in regarding its growth and production when exposed to salinity condition. The aims of this study went evaluate the effect of the saline stress in the germination phase to four cotton genotypes (BRS Rubi, BRS Safira, BRS 201 and CNPA 187 8H), using different osmotic potentials generated with increment of sodium chloride (NaCl). The saline stress was simulated using NaCl aqueous solutions in the potentials: 0.0 (Control); -0.2; -0.4; -0.6; -0.8 and -1.0 MPa. The treatments were monitored by means of tests for analysis of seeds, germination, first counting, speed germination index, length of shoot, radicle length, dry weigth of embrionic axis and shoot/radicle ratio. The tests for germination, first counting and index of germination speed were accomplished using 50 seeds for repetition and for the study of length of shoot, radicle length, dry weigth of embrionic axis and shoot/radicle ratio were used 20 seeds by repetition. For both tests four repetitions were accomplished by genotype for each one of the potentials. The seeds of each repetition were involved in papers Germitest humidified with NaCl solution corresponding to the potential. The repetitions of both tests were maintained in a germinator with saturated humidity. The analysis were initiate four days after the induction of the saline stress. The evaluations of the first three variables analyzed were accomplished daily; the seeds were remove and counted when its germinated. For the length tests just the repetitions corresponding to the potential of NaCl 0,0 MPa were analysis 4 days after the beginning of the induction of the saline stress. The analysis of the repetitions of the potentials -0,2 and -0,4 and of the potentials -0,6, -0,8 and -1,0 MPa they were accomplished with 12 and 20 days, respectively. For accomplishment of the analisis of this test the shoot of the 20 plantules of each repetition was separate from the radicle and both parts were measured. The statistical analyses were performed using the GENMOD and GLM procedures of the SAS. For the variable germination, the cultivates CNPA 187 8H and BRS Safira stood out for the potential -0.8 MPa, with averages of 89% and 81%, respectively. The test of speed germination index to cultivate BRS Safira presented the largest averages for the two higher saline potentials. It was observed that the increase of the saline potential reduces the germination percentage and speed germination index. For each day of evaluation it was verified that the increase of the saline potential causes a reduction of the length both of the shoot and of the radicle. The radicle tends to grow more than the shoot until the potential -0,4 MPa

Estudo das ligas titânio-zircônio resultantes do processo de fundição plasma-skull para aplicações como biomateriais

The aim of this work was to study a series of 11 different compositions of Ti-Zr binary alloys resistance to aggressive environment, i. e., their ability to keep their surface properties and mass when exposed to them as a way to evaluate their performance as biomaterials. The first stage was devoted to the fabrication of tablets from these alloys by Plasma-Skull casting method using a Discovery Plasma machine from EDG Equipamentos, Brazil. In a second stage, the chemical composition of each produced tablet was verified. In a third stage, the specimen were submitted to: as-cast microstructure analysis via optical and scanning electron microscopy (OM and SEM), x-ray dispersive system (EDS) chemical analysis via SEM, Vickers hardness tests for mechanical evaluation and corrosion resistence tests in a 0.9% NaCl solution to simulate exposition to human saliva monitored by open circuit potential and polarization curves. From the obtained results, it was possible to infer that specimens A1 (94,07 wt% Ti and 5,93% wt% Zr), A4 (77,81 wt % Ti and 22,19 wt % Zr) and A8 (27,83 wt% Ti and 72,17 wt% Zr), presented best performance regarding to corrosion resistance, homogeneity and hardness which are necessary issues for biomaterials to be applied as orthopedic and odontological prosthesis

Análise bromatológica de carnes antes e após o processamento para obtenção de charque

The process of salting and drying in the sun is used to preserve meat since the beginning of civilization. There is evidence that this preservation technique has arisen in Egypt, between 4,000 and 5,000 years ago. In our country, according to literature, was the first industrial product that gave the appearance of beef jerky, beef being produced, where about 70% to 75% of the muscle is composed of water, where it will be around 45% as a final product, according to the law in his article RIISPOA No. 432 provides that the jerky should contain no more than this amount of moisture in the muscular portion, or more than 15% of total ash with tolerance of up to 5% variation . Besides this parameter, proteins, lipids, ash, and minerals were analyzed in samples before and after the manufacturing process to know the content of these nutrients. Since these are considered important in product quality, thus the concentration in these samples, respectively, in the flesh Front (CD and CHD) before and after the manufacturing process for humidity were respectively 75.28% and 47.38% , the protein was 14.17 and 22.20 g / 100 g sample, 6.360 and 4.251 of lipids g/100g of the sample, and the ashes 0.974 9.144 g/100g sample, minerals like calcium and 4.074 30 , 06 ppm, sódio0, 055 and 5.401 g / L, sodium chloride, 0.139 and 13.74 g / L, potassium 237.5 and 166.8 ppm, 1.721 and 3.295 ppm iron, 0.143 and 0.135 ppm phosphorus, zinc and 4.690 6.905 ppm; magnésio14, 63 e13, 75 ppm manganese .017 e0, 007ppm, copper 0.057 and 0.039 ppm in the case of needle-type meat (CPA and CHPA), 68.04% and 44.17%, protein 13 , 72, and 24.42 g/100g of sample, 1.137 in the ash and 12.68 g / 100g of sample, and the minerals calcium 17.11 and 12.89 ppm; sódio0, 123 and 4.871 g / L, sodium chloride 0.312 and 12.39 g / L, potassium 305.3 and 182.1 ppm; ferro1, 817 and 1.513 ppm, 0.273 and 0.139 ppm phosphorus, zinc 6.305 and 4.783 ppm, 27.95 and 15.85 ppm magnesium, manganese and 0.025 0.011 ppm, 0.057 and 0.143 ppm copper and chromium 0.014 and 0.068 ppm

Interações entre a carboximetilcelulose, carbonato de cálcio e bentonita: repercussões sobre as propriedades dos fluidos de perfuração aquosos

The role of carboxymethylcellulose (CMC) in association to calcium carbonate particles (CaCO3) in most water-based drilling fluids is to reduce the fluid loss to the surrounding formation. Another essential function is to provide rheological properties capable of maintaining in suspension the cuttings during drilling operation. Therefore, it is absolutely essential to correlate the polymer chemical structure (degree of substitution, molecular weight and distribution of substituent) with the physical-chemical properties of CaCO3, in order to obtain the better result at lower cost. Another important aspect refers to the clay hydration inhibitive properties of carboxymethylcellulose (CMC) in drilling fluids systems. The clay swelling promotes an undesirable damage that reduces the formation permeability and causes serious problems during the drilling operation. In this context, this thesis consists of two main parts. The first part refers to understanding of interactions CMC-CaCO3, as well as the corresponding effects on the fluid properties. The second part is related to understanding of mechanisms by which CMC adsorption occurs onto the clay surface, where, certainly, polymer chemical structure, ionic strength, molecular weight and its solvency in the medium are responsible to affect intrinsically the clay layers stabilization. Three samples of carboximetilcellulose with different molecular weight and degree of substitution (CMC A (9 x 104 gmol DS 0.7), CMC B (2.5 x 105 gmol DS 0.7) e CMC C (2.5 x 105 gmol DS 1.2)) and three samples of calcite with different average particle diameter and particle size distribution were used. The increase of CMC degree of substitution contributed to increase of polymer charge density and therefore, reduced its stability in brine, promoting the aggregation with the increase of filtrate volume. On the other hand, the increase of molecular weight promoted an increase of rheological properties with reduction of filtrate volume. Both effects are directly associated to hydrodynamic volume of polymer molecule in the medium. The granulometry of CaCO3 particles influenced not only the rheological properties, due to adsorption of polymers, but also the filtration properties. It was observed that the lower filtrate volume was obtained by using a CaCO3 sample of a low average size particle with wide dispersion in size. With regards to inhibition of clay swelling, the CMC performance was compared to other products often used (sodium chloride (NaCl), potassium chloride (KCl) and quaternary amine-based commercial inhibitor). The low molecular weight CMC (9 x 104 g/mol) showed slightly lower swelling degree compared to the high molecular weight (2.5 x 105 g/mol) along to 180 minutes. In parallel, it can be visualized by Scanning Electron Microscopy (SEM) that the high molecular weight CMC (2.5 x 105 g/mol e DS 0.7) promoted a reduction in pores formation and size of clay compared to low molecular weight CMC (9.0 x 104 g/mol e DS 0.7), after 1000 minutes in aqueous medium. This behavior was attributed to dynamic of interactions between clay and the hydrodynamic volume of CMC along the time, which is result of strong contribution of electrostatic interactions and hydrogen bounds between carboxylate groups and hydroxyls located along the polymer backbone and ionic and polar groups of clay surface. CMC adsorbs on clay surface promoting the skin formation , which is responsible to minimize the migration of water to porous medium. With the increase of degree of substitution, it was observed an increase of pores onto clay, suggesting that the higher charge density on polymer is responsible to decrease its flexibility and adsorption onto clay surface. The joint evaluation of these results indicate that high molecular weight is responsible to better results on control of rheological, filtration and clay swelling properties, however, the contrary effect is observed with the increase of degree of substitution. On its turn, the calcite presents better results of rheological and filtration properties with the decrease of average viii particle diameter and increase of particle size distribution. According to all properties evaluated, it has been obvious the interaction of CMC with the minerals (CaCO3 and clay) in the aqueous medium

Viabilidade da cultura Cnidoscolus quercifolius POHL para produção de Biodiesel no semiárido nordestino

The northeastern semiarid is a region that presents a serious picture stagnation or slowness of the economic growth, beyond the presence of social pointers below of the averages national and regional. The half-dryness conditions become the improper region for many agricultural cultures, what it affects the local populations directly, as well as the economy that is based mainly on agriculture. Cnidoscolus quercifolius Pohl, popularly know as favelone is a native species of the semiarid region that withholds great potential for the development of the region in virtue of its multiple uses. Being an oleaginous, its production in familiar farmings makes with that biodiesel either for the misery an important alternative eradication for the possibility of occupation of enormous contingents of people. The present study it aims at to evaluate the germination of the faveleira without thorns under conditions of water and saline stresses, main stresses which the vegetal species of the semiarid one are submitted; beyond verifying the acceptance of the species for agriculturists of a cooperative in the city of Apodi/RN. The methodology used for germination corresponds to using treatments with polyethylene glycol and sodium chloride to assess water and salt stress respectively, being held in rolo. O system approach used for the verification of acceptance of faveleira was the use of interview with farmers cooperative in the study area determined. In this direction it was verified that the faveleira is a resistant species the conditions of drought and salinity of the ground, factor of great relevance, since one is about a species with high added value, making possible the development for the semiarid region. It was verified that the agriculturists are favorable the introduction of the faveleira and reveal receptive the idea to cultivate a species with potential for production of biodiesel

Estudo sobre tratamento térmico e mudança superficial da diatomita de Punaú/RN para o desenvolvimento de um auxiliar de filtração

The diatomite is a natural material that has numerous applications due to changes in their physical and chemical properties after processing. It is currently used in the industry as a sound insulator , filter aid and industrial load . The filter material shall be inert chemical composition , which will diatomite confers a high commercial value and performance not found in other particulate materials , for this application. The diatomite surface undergoes changes after thermal treatment at high temperatures , from 800ºC , with properties that enable its application in the food , beverage , pharmaceutical , cosmetic and textiles . In this work , we developed a study on thermal treatment on natural diatomite to adapt their properties to the application as a filter aid . The heat treatments were performed in an open oven at temperatures of 800ºC , 1000ºC and 1200ºC for a time of 24 hours. Reagents were added in the constitution of the samples analyzed. The reagents used were sodium carbonate (Na2CO3 ) and sodium chloride (NaCl) . The samples were characterized by x - ray diffraction , x -ray fluorescence , scanning electron microscopy , analysis and particle size distribution , specific surface area by the BET method , and pore volume by BJH method. The results showed a reduction in porosity of the material as well as a significant increase in specific surface area after heat treatment and the reactants in the ratio of 3 wt%. The diatomaceous earth , after heat treatment , undergone changes in its coloration , varying in white, cream and beige , which directly interferes with the speed of filtration materials process. All results obtained before and after heat treatment of the material with the values obtained for samples already used industrially , Brazilian and American industry , which were characterized using the same test methods performed with the samples in the study were compared and showed promising efficiency when material studied in the region of Punaú - RN , after processing , reagent addition and heat treatment, as an element in the composition of filter .

Caracterização físico-química e química do fruto do juazeiro (Ziziphus joazeiro Mart) e avaliação da sua conservação por fermentação láctica

Considering the plant biodiversity in the Brazilian Northeast, whose components can be inserted into sustainable production systems, the jujube (Ziziphus joazeiro Mart.) emerges as to recovery of its fruit. The present study has as objective to characterize the fruit of the jujube under the physical, physicochemical and chemical approach and assess its conservation by spontaneous lactic fermentation under the influence of chloride, sodium, calcium and potassium. According to the legislation, vegetable acidified by fermentation that is subjected to lactic acid fermentation in order to achieve a final product pH less than or equal to 4.5. The results of the physical, chemical and physico-chemistry of ripe fruit jujube showed the potential of this species for agro-processing. The yield of edible portion (91.83%), soluble solids content (18,98º Brix), titratable acidity (0.14% citric acid), pH (5.30) and its composition, divided in moisture (79.01%), protein (2.01%), lipids (0.52%), carbohydrate (17.59%), fiber, ash (0.76%) and its minerals were consistent with the characteristic profile fruits, thus favoring the development of spontaneous lactic fermentation. The minimum pH and titratable acidity observed maximum in the fermentation process under the influence of mixtures of salts (NaCl and KCl NaCl2) values ranged from 3.4 to 3.7 and from 0.54 to 0.95 (% lactic acid), respectively. The profile of the lactic fermentation of fruit of jujube in brine, fermented microbiological quality and the result of analysis of primary sensory prepared preserved, the application of endorsed by the consumer sensory evaluation, more particularly, derived from fermented fruit preserved in the presence of chloride sodium, in accordance with the traditional techniques of lactic fermentation of vegetables. The results of sensory evaluation conducted with 100 consumers (tasters) revealed an acceptance rate equal to 78% of the preserve. Despite restrictions on the sensory acceptability of fermented under the influence of salts (KCl and CaCl2) substitutes sodium chloride, preserved these perspectives presented to balance the optimization of mixtures, health product safety and consumer awareness towards prefer a more healthy product with reduced sodium content.

Contribuição da poliacrilamida parcialmente hidrolisada em associação com a bentonita em fluidos de perfuração aquosos

In this study, we investigated the effect of addition of partially hydrolyzed polyacrylamide (HPAM) and bentonite in the physicochemical properties of acquous drilling fluids. Two formulations were evaluated: F1 formulation, which was used as reference, containing carboxymethylcellulose (CMC), magnesium oxide (MgO), calcite (calcium carbonate - CaCO3 ), xanthan gum, sodium chloride (NaCl) and triazine (bactericidal); and F2, containig HPAM steady of CMC and bentonite in substituition of calcite. The prepared fluids were characterized by rheological properties, lubricity and fluid loss. Calcite was characterized by granulometry and thermal gravimetric analysis (TGA). The formulation F2 presented filtration control at 93◦C 34 mL while F1 had total filtration. The lubricity coefficient was 0.1623 for F2 and 0.2542 for F1, causing reduction in torque of 25% for F1 and 52 % for F2, compared to water. In the temperature of 49 ◦C and shear rate of 1022 s −1 , the apparent viscosities were 25, 5 and 48 cP for F1 and F2 formulation, respectively, showing greater thermal resistance to F2. With the confirmation of higher thermal stability of F2, factorial design was conducted in order to determine the HPAM and of bentonite concentrations that resulted in the better performance of the fluids. The statistical design response surfaces indicated the best concentrations of HPAM (4.3g/L) and bentonite (28.5 g/L) to achieve improved properties of the fluids (apparent viscosity, plastic viscosity, yield point and fluid loss) with 95% confidence, as well as the correlations between these factors (HPAM and bentonite concentrations). The thermal aging tests indicated that the formulations containing HPAM and bentonite may be used to the maximum temperature until 150 ◦C. The analyze of the filter cake formed after filtration of fluids by X-ray diffraction showed specific interactions between the bentonite and HPAM, explaining the greater thermal stability of F2 compared to the fluid F1, that supports maximum temperature of 93 ◦C.