Caracterização de compósitos Nb-20%cu obtidos por moagem de alta energia e sinterizados por fase líquida

In this work, was studied the formation of a composite of the refractory metal niobium with copper, through the process of high-energy milling and liquid phase sintering. The HEM can be used to synthesize composite powders with high homogeneity and fine size particle distribution. It may also produce the solid solubility in immiscible systems such as Nb-Cu, or extend the solubility of systems with limited solubility. Therefore, in the immiscible system Cu-Nb, the high-energy milling was successfully used to obtain the composite powder particles. Initially, the formation of composite particles during the HEM and the effect of preparation technique on the microstructure of the material was evaluated. Four loads of Nb and Cu powders containing 20%wt Cu were synthesized by MAE in a planetary type ball mill under different periods of grinding. The influence of grinding time on the metal particles is evaluated during the process by the withdrawal of samples at intermediate times of milling. After compaction under different forces, the samples were sintered in a vacuum furnace. The liquid phase sintering of these samples prepared by HEM produced a homogeneous and fine grained. The composite particles forming the sintered samples are the addition of a hard phase (Nb) with a high melting point, and a ductile phase (Cu) with low melting point and high thermal and electrical conductivities. Based on these properties, the Nb-Cu system is a potential material for many applications, such as electrical contacts, welding electrodes, coils for generating high magnetic fields, heat sinks and microwave absorbers, which are coupled to electronic devices. The characterization techniques used in this study, were laser granulometry, used to evaluate the homogeneity and particle size, and the X-ray diffraction, in the phase identification and to analyze the crystalline structure of the powders during milling. The morphology and dispersion of the phases in the composite powder particles, as well the microstructures of the sintered samples, were observed by scanning electron microscopy (SEM). Subsequently, the sintered samples are evaluated for density and densification. And finally, they were characterized by techniques of measuring the electrical conductivity and microhardness, whose properties are analyzed as a function of the parameters for obtaining the composite

Desenvolvimento e validação de método analítico para determinação de teor de ácido gálico e catequina no fitoterápico sanativo® por cromatografia líquida de alta eficiência

The herbal medicine Sanativo® is produced by the Pernambucano Laboratory since 1888 with indications of healing and hemostasis. It is composed of a fluid extract about Piptadenia colubrina, Schinus terebinthifolius, Cereus peruvianus and Physalis angulata. Among the plants in their composition, S. terebinthifolius and P. colubrina have in common phenolic compounds which are assigned most of its pharmacological effects. The tannins, gallic acid and catechin were selected as markers for quality control. The aim of this study was the development and validation of analytical method by HPLC/UV/DAD for the separation and simultaneous quantification of gallic acid (GAC) and catechin (CTQ) in Sanativo®. The chromatographic system was to stationary phase, C-18 RP column, 4,6 x 150 mm (5 mm) under a temperature of 35 ° C, detection at 270 and 210 nm. The mobile phase consisted of 0.05% trifluoroacetic acid and methanol in the proportions 88:12 (v/v), a flow rate of 1 ml/min. The analytical method presented a retention factor of 0.30 and 1.36, tail factor of 1.8 and 1.63 for gallic acid and catechin, respectively, resolution of 18.2, and theoretical plates above 2000. The method validation parameters met the requirements of Resolution n º 899 of May 29, 2003, ANVISA. The correlation coefficient of linear regression analysis for GAC and CTQ from the standard solution was 0.9958 and 0.9973 and when performed from the Sanativo® 0.9973 and 0.9936, the matrix does not interfere in the range 70 to 110 %. The limits of detection and quantification for GAC and CQT were 3.25 and 0.863, and 9.57 and 2.55 mg/mL, respectively. The markers, GAC and CQT, showed repetibility (coefficient of variation of 0.94 % and 2.36 %) and satisfactory recovery (100.02 ± 1.11 % and 101.32 ± 1.36 %). The method has been characterized selective and robust quantification of GAC and CTQ in the Sanativo® and was considered validated

Avaliação citológica em base líquida de fármacos moduladores estrogênicos

Hormone therapy is an important tool in the treatment of breast cancer and tamoxifen represents one of the most important drugs used in this type of treatment. Recently other drugs based on the inhibition of aromatase had been developed, this enzyme is responsible for the synthesis of estrogenic esteroids from the androgenic ones. The objective of this study would be the development of a quantitative cytological model of murine estral analysis that allowed the characterization of different hormone drugs effect over vaginal epithelium. The technique of monochromatic staining with Evans blue (C.I. 23860) showed to be efficient in the qualitative and quantitative classification of the cycle. It had been observed differences in the cytological standard of animals submitted to the studied drugs; tamoxifen presented a widening of phases of lesser maturation (diestrais), while anastrozole and exemestane increased the duration of the phases of larger maturation (estrais). The data were analysed through a cubical non linear regression (spline) which allowed a better characterization of the drugs, suggesting a proper cytological profile to the antagonism of the estrogen receptor (tamoxifen), aromatase competition (anastrozole) and inhibition of the enzyme (exemestane)

Modelagem de equações estruturais na análise de dados de serviços em comunicações móveis

In recent decades, changes have been occurring in the telecommunications industry, allied to competition driven by the policies of privatization and concessions, have fomented the world market irrefutably causing the emergence of a new reality. The reflections in Brazil have become evident due to the appearance of significant growth rates, getting in 2012 to provide a net operating income of 128 billion dollars, placing the country among the five major powers in the world in mobile communications. In this context, an issue of increasing importance to the financial health of companies is their ability to retain their customers, as well as turn them into loyal customers. The appearance of infidelity from customer operators has been generating monthly rates shutdowns about two to four percent per month accounting for business management one of its biggest challenges, since capturing a new customer has meant an expenditure greater than five times to retention. For this purpose, models have been developed by means of structural equation modeling to identify the relationships between the various determinants of customer loyalty in the context of services. The original contribution of this thesis is to develop a model for loyalty from the identification of relationships between determinants of satisfaction (latent variables) and the inclusion of attributes that determine the perceptions of service quality for the mobile communications industry, such as quality, satisfaction, value, trust, expectation and loyalty. It is a qualitative research which will be conducted with customers of operators through simple random sampling technique, using structured questionnaires. As a result, the proposed model and statistical evaluations should enable operators to conclude that customer loyalty is directly influenced by technical and operational quality of the services offered, as well as provide a satisfaction index for the mobile communication segment

Controle de posição de uma plataforma plana para captação de radiação solar

This study aims at the design, development and performance evaluation of a flat platform to capture incident solar radiation. The design and implementation of a fuzzy system for the efficient control of the solar tracking movement of the platform are also presented

Detecção de metamidofós em solos por métodos ecotoxicológico e cromatografia líquida acoplada à espectrometria de massas sequencial (LC-MS/MS)

Soil contamination by pesticides is an environmental problem that needs to be monitored and avoided. However, the lack of fast, accurate and low cost analytical methods for discovering residual pesticide in complex matrices, such as soil, is a problem still unresolved. This problem needs to be solved before we are able to assess the quality of environmental samples. The intensive use of pesticides has increased since the 60s, because the dependence of their use, causing biological imbalances and promoting resistance and recurrence of high populations of pests and pathogens (upwelling). This has contributed to the appearance of new pests that were previously under natural control. To develop analytical methods that are able to quantify residues pesticide in complex environment. It is still a challenge for many laboratories. The integration of two analytical methods one ecotoxicological and another chemical demonstrates the potential for environmental analysis of methamidophos. The aim of this study was to evaluate an ecotoxicological method as "screening" analytical methamidophos in the soil and perform analytical confirmation in the samples of the concentration of the analyte by chemical method LC-MS/MS In this work we tested two soils: a clayey and sandy, both in contact with the kinetic methamidophos model followed pseudo-second order. The clay soil showed higher absorption of methamidophos and followed the Freundlich model, while the sandy, the Langmuir model. The chemical method was validated LC-MS/MS satisfactory, showing all parameters of linearity, range, precision, accuracy, and sensitivity adequate. In chronic ecotoxicological tests with C. dubia, the NOEC was 4.93 and 3.24 for ng L-1 of methamidophos to elutriate assays of sandy and clay soils, respectively. The method for ecotoxicological levels was more sensitive than LC-MS/MS detection of methamidophos, loamy and sandy soils. However, decreasing the concentration of the standard for analytical methamidophos and adjusting for the validation conditions chemical acquires a limit of quantification (LOQ) in ng L-1, consistent with the provisions of ecotoxicological test. The methods described should be used as an analytical tool for methamidophos in soil, and the ecotoxicological analysis can be used as a "screening" and LC-MS/MS as confirmatory analysis of the analyte molecule, confirming the objectives of this work

Estudo de um compósito Nb-15%pCu obtidos por moagem de alta energia e sinterizados por fase líquida

There is great difficulty in forming a composite refractory metal niobium with copper. This is due to the fact that Nb-Cu system is almost mutually immiscible and may be neglected solubility between them. These properties hinder or prevent obtaining homogeneous and high-density structures, conventionally prepared. This study aims to analyze the use of high-energy milling process (MAE) to implement these natural difficulties, with regard to the densification of the sintered bodies. The MAE and the press were used in the preparation of powders, to obtain a fine and homogeneous distribution of the grain size. Four loads Nb and Cu powders containing 15% by weight of Cu were then milled for MAE in a planetary type ball mill under various milling times and speeds. The results obtained by MAE were analyzed by scanning electron microscopy (SEM), according to the parameters of time and grinding speed. The samples were compacted under pressure of 200 MPa, were then sintered in liquid phase in a vacuum furnace at temperatures of 1100 ° C / 60 min and 1200 ° C / 60 min. Then it was used to characterize diffraction of X-rays to identify the phases. The microstructures of the sintered samples were observed and evaluated using scanning electron microscopy (SEM). Vickers Microhardness tests were performed, obtaining higher values for the sintered bodies in the largest of the post milling times and the larger grinding speeds. It was found that the liquid phase sintering of the samples that were processed by MAE produced at the end of a homogeneous and densified structure in 77,4% relative to the value of the theoretical density of the composite

As relações da tríplice hélice nas fundações de apoio brasileiras: uma avaliação da dinâmica de captação de recursos para projetos de inovação

Foundations support constitute one of the types of legal entities of private law forged with the purpose of supporting research projects, education and extension and institutional, scientific and technological development of Brazil. Observed as links of the relationship between company, university, and government, foundations supporting emerge in the Brazilian scene from the principle to establish an economic platform of development based on three pillars: science, technology and innovation – ST&I. In applied terms, these ones operate as tools of debureaucratisation making the management between public entities more agile, especially in the academic management in accordance with the approach of Triple Helix. From the exposed, the present study has as purpose understanding how the relation of Triple Helix intervenes in the fund-raising process of Brazilian foundations support. To understand the relations submitted, it was used the interaction models University-Company-Government recommended by Sábato and Botana (1968), the approach of the Triple Helix proposed by Etzkowitz and Leydesdorff (2000), as well as the perspective of the national innovation systems discussed by Freeman (1987, 1995), Nelson (1990, 1993) and Lundvall (1992). The research object of this study consists of 26 state foundations that support research associated with the National Council of the State Foundations of Supporting Research - CONFAP, as well as the 102 foundations in support of IES associated with the National Council of Foundations of Support for Institutions of Higher Education and Scientific and Technological Research – CONFIES, totaling 128 entities. As a research strategy, this study is considered as an applied research with a quantitative approach. Primary research data were collected using the e-mail Survey procedure. Seventy-five observations were collected, which corresponds to 58.59% of the research universe. It is considering the use of the bootstrap method in order to validate the use of the sample in the analysis of results. For data analysis, it was used descriptive statistics and multivariate data analysis techniques: the cluster analysis; the canonical correlation and the binary logistic regression. From the obtained canonical roots, the results indicated that the dependency relationship between the variables of relations (with the actors of the Triple Helix) and the financial resources invested in innovation projects is low, assuming the null hypothesis of this study, that the relations of the Triple Helix do not have interfered positively or negatively in raising funds for investments in innovation projects. On the other hand, the results obtained with the cluster analysis indicate that entities which have greater quantitative and financial amounts of projects are mostly large foundations (over 100 employees), which support up to five IES, publish management reports and use in their capital structure, greater financing of the public department. Finally, it is pertinent to note that the power of the classification of the logistic model obtained in this study showed high predictive capacity (80.0%) providing to the academic community replication in environments of similar analysis.

Caracterização de compósitos Nb-20%cu obtidos por moagem de alta energia e sinterizados por fase líquida

In this work, was studied the formation of a composite of the refractory metal niobium with copper, through the process of high-energy milling and liquid phase sintering. The HEM can be used to synthesize composite powders with high homogeneity and fine size particle distribution. It may also produce the solid solubility in immiscible systems such as Nb-Cu, or extend the solubility of systems with limited solubility. Therefore, in the immiscible system Cu-Nb, the high-energy milling was successfully used to obtain the composite powder particles. Initially, the formation of composite particles during the HEM and the effect of preparation technique on the microstructure of the material was evaluated. Four loads of Nb and Cu powders containing 20%wt Cu were synthesized by MAE in a planetary type ball mill under different periods of grinding. The influence of grinding time on the metal particles is evaluated during the process by the withdrawal of samples at intermediate times of milling. After compaction under different forces, the samples were sintered in a vacuum furnace. The liquid phase sintering of these samples prepared by HEM produced a homogeneous and fine grained. The composite particles forming the sintered samples are the addition of a hard phase (Nb) with a high melting point, and a ductile phase (Cu) with low melting point and high thermal and electrical conductivities. Based on these properties, the Nb-Cu system is a potential material for many applications, such as electrical contacts, welding electrodes, coils for generating high magnetic fields, heat sinks and microwave absorbers, which are coupled to electronic devices. The characterization techniques used in this study, were laser granulometry, used to evaluate the homogeneity and particle size, and the X-ray diffraction, in the phase identification and to analyze the crystalline structure of the powders during milling. The morphology and dispersion of the phases in the composite powder particles, as well the microstructures of the sintered samples, were observed by scanning electron microscopy (SEM). Subsequently, the sintered samples are evaluated for density and densification. And finally, they were characterized by techniques of measuring the electrical conductivity and microhardness, whose properties are analyzed as a function of the parameters for obtaining the composite