Avaliacao de polimorfismos nos genes XPD e XRCC3 em carcinomas orais de celulas escamosas

Oral squamous cell carcinoma (OSCC) is an important cause of morbidity and mortality worldwide despite recent advances in treatment. There are several studies aiming to find markers that may improve the assessment of this disease prognosis. Studies about genetic polymorphisms have gained prominence due to their influence on individual susceptibility to cancer development. The aim of this study was to evaluate the association between the frequency of polymorphisms XPD Lys751Gln and XRCC3 Thr241Met and clinicopathological features of OSCC cases, including age, sex, presence or absence of metastases, and histological grading of malignancy according to Bryne (1998). Sample consisted of 54 cases of OSCC and 40 cases of inflammatory fibrous hyperplasia (IFH). OSCC cases were classified as low or high grade. DNA samples were previously extracted from paraffin blocks. Genotypes for each case were determined through PCR-RFLP (polymerase chain reaction - restriction fragment length polymorphism). Results were analyzed by Fisher s exact test and Chi-square test and the odds ratio was calculated considering p < 0.05 to indicate statistical significance. For XPD, Lys/Gln genotype was more common in IFHs (n=28; 70%) than in OSCCs (n=24; 44.4%) (OR: 0.3; p<0.05). Frequency of Gln allele was higher in high-grade lesions when compared to low grade lesions (0.48 and 0.21, respectively) (OR: 3.4; p<0.05). For XRCC3, Met allele was more common in OSCC than in IFH (0.49 and 0.35, respectively) (OR: 2.6; p<0.05). Met/Met genotype was associated with presence of metastases (OR: 8.1; p<0.05). There was no statistically significant association between the genotypes and the age or sex of patients. In the present sample, the higher frequency of XPD Gln allele in IFH reveals a possible protective role of this variant against the development of OSCC. However, its association with high-grade lesions indicates that this allele could influence the tumor progression after the neoplasia development. The presence of XRCC3 Met allele, in turn, seems to contribute to the development of OSCC and metastases

Estudo da correlação das características clínico-patológicas do câncer colorretal com a expressão imunohistoquímica de proteínas da progressão tumoral

Except the non-melanoma skin tumors, colorectal cancer is the second most common in the Southeastern Region of Brazil, the third most common in the Southern and Central Regions. It is also the forth most common in the Northern Region and it is the fifth one in the Northeastern. To assess pathological and clinical variables of colorectal Cancer is crucial to know the possible conclusions for the survival of patients and point out the characteristics in the progress of tumor, such as the profile of tumor invasion and its angiogenesis. This work focuses on analyzing clinically and pathologically some settings in colorectal cancer patients (CRC) in the city of Natal and its countryside through those variables as parameters of prognosis and determine the level of protein expression, for instance: E-cadherin (E-cad), beta- -catenin (β-cat), galectin-3 (gal-3), matrix metalloproteinases (MMP) 2 and 9 and vascular-endothelial growth factor alpha (α VEGF) in the tumor tissues. A retrospective study was done in colorectal cancer cases in the regions of Rio Grande do Norte state from 1995 to 2005, specifically in Natal city/RN/Brazil. The pathological and clinical variables, such as: age, gender, ethnicity, lifestyle, family history, the location of the primary tumor, level of differentiation, TDM staging, modified Dukes’, treatment and survival were analyzed. The pathological and clinical data were collected from medical records through a specific form and were filed on Excel. A total of 534 patients were selected from the Pathology Department file in this institution, however, 176 patients were excluded. 358 patients were included for Epidemiological analysis and its clinical and pathological correlations were selected. 180 patients were also selected for histological and immunohistochemical studies. The tumor progression of these selected proteins mentioned before were analyzed. The Paraffin blocks of these samples were treated by Microarray Tissue technique and its blades subjected to immunohistochemistry to test the intensity of these proteins in tumor tissues. The results of this analysis were correlated with clinicopathologic variables of patients. Statistical analysis using the chi-frame Pearson test and analysis of midlife by Kaplan-Meier curve was also utilized. P values < 0.05 were considered statistically significant. The average age of our sample was 58.8 years and 51.7 % were female. Alcohol consumption has increased by 1.71 time the risk of death by CCR (p = 0.034) and tobacco consumption increased 2.7 times the chance of developing tumors of high TNM stage (p = 0.001). Cancer patients had a family history of 3,833 times the chance of developing the CCR (p = 0.002). The expression of MMP-2 showed a significant association with tumors of high TNM stage (p <0.046) and mortality (p = 0.041). The α VEGF expression had statistically significant correlation with high TNM stage (p <0.009), degree of cell indifferentiation (p <0.025) and mortality (p <0.035). Expressions of E-cadherin and beta-catetina demonstrated tumor linked to high TNM stage (p = 0.0001) and Dukes› modified (p = 0.05), lesions in the rectum (p = 0.03 and p = 0.007, respectively), smoking (p = 0.05) and indifferentiation (p = 0.001). The expression of Gal-3 showed statistical significance with high TNM stage of patients (p = 0.01), smokers (p = 0.01), alcohol drinking (p = 0.03), indifferentiation (p = 0.0001) and mortality (p = 0.0001). Based on the results, therefore, we could realize that lifestyle and family history had correlation in the CCR prognosis, as well as MMP-2 expression, MMP-9, VEGF alpha, E-cadherin, Beta-catenin and Galectin-3 were important prognostic markers in tumor progression in colorectal cancer.

Avaliação da conformidade de blocos cerâmicos para alvenaria de vedação produzidas na Região Integrada de Desenvolvimento da Grande Teresina

This research presents an outlook of the industries of red ceramic in the region next to the city of Teresina and an analysis of the ceramic products producted in this pole. The microregion investigated possesses 13 boroughs where were identified 32 ceramic in operation, being that 24 are located in Teresina, the ceramic region more important of Piauí, 1 is located in the city of Miguel Leão and 7 is located in Timon city that belongs to the state of Maranhão. The majority of ceramics are pulverized in these two cities, Teresina and Timon , responsible by a largely production independent of distance between fabric and consumer market. Furthermore, there is an artisanal production realized in other boroughs, mainly manual conformation bricks, where are producted diverse types of handicraft and ceramics utilitarian. The objective of this research is to evalue the conformity of ceramic blocks for brick of obstruction made by red ceramic industry of microregion at studying, verifying their pontentialities and adequacy in terms of production. In this research universe made a search of ceramic industries related to the Foundation CEPRO (Foundation Center of Research Social and Economic of Piauí). For the analysis of the ceramic products , were colected 60 crude bricks sample in three industries for their characterization, and 39 burned bricks sample for the Evaluation of Conformity. The results of the characterization made reached a accetptable standard in all formulations and temperature studied. The burned samples were applied to the geometric, physical and mechanical assays according to the ABNT standards (Brazilian Association of Technical Standards). The results of the physical assays showed that all the samples are at the same band recommended by standard. However, through the geometric assays just two industries did not present results according to the standard, due to lack of control in their process such as in their equipments. Taking into account the mechanical properties, only one industry investigated was not according to the standard

Estudo numérico do comportamento de muros de arrimo em alvenaria estrutural de blocos vazados

Usually masonry structures has low tension strength, hence the design to flexural efforts can results in high reinforcement ratio, specification of high unit and prism strength, structural members with larger section dimensions and modification in structural arrangement to be possible to use masonry members. The main objective of this study is to evaluate the stiffness, the efforts distribution and the effect of horizontal elements (girders) and vertical elements (counterforts) distribution on the behavior of masonry blocks retaining walls. For this purpose, numerical modeling was performed on typical retaining wall arrangements by varying the amount and placement of horizontal and vertical elements, beyond includes elements simulating the reactions of the soil supporting the foundation of the wall. The numerical modeling also include the macro modeling strategy in which the units, mortar and grout are discretized by a standard volume that represents the masonry elastic behavior. Also, numerical model results were compared with those ones of simplified models usually adopted in bending design of masonry elements. The results show horizontal displacements, principal and shear stresses distribution, and bending moments diagrams. From the analysis it was concluded that quantity and manner of distribution of the girders are both important factors to the panel flexural behavior, the inclusion of the foundation changed significantly the behavior of the wall, especially the horizontal displacements, and has been proposed a new way of considering the flanges section of the counterforts

Redes neurais artificiais no ambiente de redes industriais foundation fieldbus usando blocos funcionais padrões

Industrial automation networks is in focus and is gradually replacing older architectures of systems used in automation world. Among existing automation networks, most prominent standard is the Foundation Fieldbus (FF). This particular standard was chosen for the development of this work thanks to its complete application layer specification and its user interface, organized as function blocks and that allows interoperability among different vendors' devices. Nowadays, one of most seeked solutions on industrial automation are the indirect measurements, that consist in infering a value from measures of other sensors. This can be made through implementation of the so-called software sensors. One of the most used tools in this project and in sensor implementation are artificial neural networks. The absence of a standard solution to implement neural networks in FF environment makes impossible the development of a field-indirect-measurement project, besides other projects involving neural networks, unless a closed proprietary solution is used, which dos not guarantee interoperability among network devices, specially if those are from different vendors. In order to keep the interoperability, this work's goal is develop a solution that implements artificial neural networks in Foundation Fieldbus industrial network environment, based on standard function blocks. Along the work, some results of the solution's implementation are also presented

Estratégia de escalonamento de controladores PID baseado em regras Fuzzy para redes industriais foundation fieldbus usando blocos padrões

The main objective of work is to show procedures to implement intelligent control strategies. This strategies are based on fuzzy scheduling of PID controllers, by using only standard function blocks of this technology. Then, the standardization of Foundation Fieldbus is kept. It was developed an environment to do the necessary tests, it validates the propose. This environment is hybrid, it has a real module (the fieldbus) and a simulated module (the process), although the control signals and measurement are real. Then, it is possible to develop controllers projects. In this work, a fuzzy supervisor was developed to schedule a network of PID controller for a non-linear plant. Analyzing its performance results to the control and regulation problem

Análise da Conformidade e Caracterização da Matéria- Prima Empregada na Fabricação de Blocos Cerâmicos na Região Metropolitana de Salvador

The potential market of the metropolitan area of Salvador accounts for the estimated consumption of roughly 800 million horizontally perforated extruded clay bricks a year. The growing demand of consumers along with the competitiveness of the structural ceramic sector has driven forward a number of recent efforts and investments towards improving the quality of structural ceramics. In this scenario, the present study focused on sampling and evaluating the conformity of 8-hole horizontally perforated extruded clay bricks manufactured by different plants (A, B and C) in the metropolitan area of Salvador. In addition, representative clay and sandy-clay materials were collected from each plant and characterized by conventional physical, chemical and mineralogical techniques. Finally, experimental compositions designated as A, B and C, according to the source, were prepared by mixing different contents of the raw materials collected in the plants, fired at different temperatures and characterized. The results revealed a series of non conformities regarding ABNT guidelines. The characterization of raw materials revealed the presence of kaolinite and ilite in concentrations ranging from 64 to 90 wt.% along with free quartz (10 - 25%). The sandy-clay samples consisted basically of kaolinite. All raw materials depicted low contents of organics, amorphous constituents, alkaline oxides and feldspar. An analysis of the firing behavior of all different ceramic compositions revealed that the linear contraction of composition A was rather significant considering the temperature range evaluated, and it justifies the significant dimensional non conformity that was shown by bricks made with the ceramic A

Estudo e caracterização de matérias-primas para o desenvolvimento de blocos sílico-calcários

The types of products manufactured calcium silicate blocks are very diversified in its characteristics. They include accessory bricks, blocks, products in dense material, with or without reinforcements of hardware, great units in cellular material, and thermal insulating products. The elements calcium silicate are of great use in the prefabricated construction, being formed for dense masses and hardened by autoclaving. This work has for objective develop formulations that make possible the obtaining of calcium silicate blocks with characteristics that correspond the specifications technical, in the State of the Rio Grande of the North, in finality of obtaining technical viability for use in the civil construction. The work studied the availability raw materials from convenient for the production of calcium silicate blocks, and the effect of variations of the productive process on the developed products. The studied raw materials were: the quartz sand from the city of São Gonçalo do Amarante/RN, and two lime, a hydrated lime and a pure lime from the city of Governador Dix-Sept Rosado/RN. The raw materials collected were submitted a testes to particle size distribution, fluorescence of X rays, diffraction of X rays. Then were produced 8 formulations and made body-of-test by uniaxial pressing at 36 MPa, and cured for 7 hours at about 18 kgf/cm2 pressing and temperature of approximately 180 °C. The cure technological properties evaluated were: lineal shrinkage, apparent density, apparent porosity, water absorption, modulus of rupture flexural (3 points), resistance compression, phase analysis (XRD) and micromorphological analysis (SEM). From the results presented the technological properties, was possible say that utilization of hydrated lime becomes more viable its utilization in mass limestone silica, for manufacture of calcium silicate blocks

Estudo térmico e de materiais na construção de casas populares com blocos confeccionados a partir de um composto a base de cimento, gesso, eps e raspa de pneu

We built an experimental house on an UFRN´s land using blocks made by a composite consisting of cement, plaster, EPS, crushed rubber and sand. Several blocks were made from various compositions and we made preliminary tests of mechanical and thermal resistance, choosing the most appropriate proportion. PET bottles were used inside the block to provide thermal resistance. In this work, a second function was given to the bottles: to serve as a docking between the blocks, because the ends of the cylinders came out of each block on top as well as at the bottom, with the bottom cut, allowing to fit of the extremities of the upper cylinder of a block in the lower holes of the other one, which were formed by the cutting already mentioned. Minimum compression tests were performed according to ABNT standards for walls closing blocks (fence). With that house built, we did studies of thermal performance in order to ascertain conditions of comfort, checking external and internal temperatures in the walls and in the ambient, among other variables, such as wind speed and relative humidity. The resulting blocks provided adequate thermal insulation to the environment, where the walls presented differences up to 11.7 ºC between the outer and inner faces, getting the maximum temperature inside the house around 31 °C, within the so-called thermal comfort zone for warm climates. At the end of the experiments it was evident the effectiveness of that construction in order to provide thermal comfort in the internal environment of the house, as well as we could confirm the viability of building houses from recyclable materials, reducing the constructive costs, becoming a suitable alternative for low- incoming families. Moreover, besides the low cost, the proposal represents an alternative use of various recyclable materials, therefore considered an ecological solution

Compósito para fabricação de blocos para construção de casas: estudos térmico e de materiais

We present two models of blocks made of composite material obtained from the use of cement, plaster, EPS crushed, shredded tire, mud, sand and water, for the construction of popular housing. Were made metal molds for the manufacture of blocks to be used in the construction of a residence for low-income families. Performed tests of compressive strength of the composite for various formulations that met the specific standard for blocks used in construction. To study the thermal conductivity of the composite for further study of thermal comfort generated in a residence built with the proposed composite. We also determined the mass-specific and water absorption for each formulation studied. Using a home already built with another composite material, made up the closing of a window with the building blocks and found the thermal insulation, measuring external and internal temperatures of the blocks. The blocks had made good thermal insulation of the environment, resulting in differences of up to 12.6°C between the outer and inner faces. It will be shown the feasibility of using composite for the end proposed and chosen the most appropriate wording

Avaliação da temperatura de cristalização da parafina em sistemas: parafina, solvente e tensoativo

The formation of paraffin deposits is common in the petroleum industry during production, transport and treatment stages. It happens due to modifications in the thermodynamic variables that alter the solubility of alkanes fractions present in petroleum. The deposition of paraffin can provoke significant and growing petroleum losses, arriving to block the flow, hindering to the production. This process is associated with the phases equilibrium L-S and the stages and nucleation, growth and agglomeration the crystals. That process is function of petroleum intrinsic characteristics and temperature and pressure variations, during production. Several preventive and corrective methods are used to control the paraffin crystallization, such as: use of chemical inhibitors, hot solvents injection, use of termochemistry reactions, and mechanical removal. But for offshore exploration this expensive problem needs more investigation. Many studies have been carried through Wax Appearance Temperature (WAT) of paraffin; therefore the formed crystals are responsible for the modification of the reologics properties of the oil, causing a lot off operational problems. From the determination of the WAT of a system it is possible to affirm if oil presents or not trend to the formation of organic deposits, making possible to foresee and to prevent problems of wax crystallization. The solvent n-paraffin has been widely used as fluid of perforation, raising the production costs when it is used in the removal paraffin deposits, needing an operational substitute. This study aims to determine the WAT of paraffin and the interference off additives in its reduction, being developed system paraffin/solvent/surfactant that propitiates the wax solubilization. Crystallization temperatures in varied paraffin concentrations and different solvents were established in the first stage of the experiments. In the second stage, using the methodology of variation of the photoelectric signal had been determined the temperature of crystallization of the systems and evaluated the interferences of additives to reduction of the WAT. The experimental results are expressed in function of the variations of the photoelectric signals during controlled cooling, innovating and validating this new methodology to determine WAT, relatively simple with relation the other applied that involve specific equipments and of high cost. Through the curves you differentiate of the results had been also identified to the critical stages of growth and agglomeration of the crystals that represent to the saturation of the system, indicating difficulties of flow due to the increase of the density

Modelagem e simulação da solubilização da parafina em tubos circulares e em regime laminar

O óleo produzido nos novos campos de petróleo está cada vez mais parafínico e viscoso, com isso, à medida que o óleo é escoado, parafinas são depositadas sobre as paredes internas do tubo, e ao longo do tempo, tendem a reduzir drasticamente a área transversal ao escoamento. Visando estudar o processo de solubilização da parafina em dutos, esse trabalho objetiva desenvolver modelos matemáticos que represente o processo, com base nos fenômenos envolvidos no mesmo tais como transferência de massa, transferência de energia e equilíbrio sólido-líquido, implementando-os em um ambiente de desenvolvimento VBA (Visual Basic) for Excel ®. O presente trabalho foi realizado em quatro etapas: i) modelagem dos fenômenos de transferência de calor e massa, ii) modelagem da rotina dos coeficientes de atividade através do modelo UNIFAC e modelagem do sistema de equilíbrio sólido-líquido; iii) modelagem matemática do processo de solubilização e cálculo da espessura da parafina ao longo do tempo; iv) implementação dos modelos em um ambiente de desenvolvimento VBA for Excel® e criação de um simulador com uma interface gráfica, para simular o processo de solubilização da parafina depositada em dutos e sua otimização. O simulador conseguiu produzir soluções bastante adequadas, mantendo continuidade das equações diferenciáveis do balanço de energia e de massa, com uma interpretação física viável, sem a presença de dissipação de oscilações nos perfis de temperatura e massa. Além disso, esse simulador visa permitir a simulação nas diversas condições de escoamento, bem como compreender a importância das variáveis (vazão, temperatura de entrada, temperatura externa, cadeia carbônica do solvente). Através dos resultados foram possíveis verificar os perfis de temperatura, fração molar e o de solubilização

Aplicação da parafina e do óleo de linhaça como hidrofobizantes da vermiculita, para remoção de derivados de óleo diesel resentes em água produzida sintética

Produced water has lately aroused interest due to their high degree of salinity, suspended oil particles, chemicals added in various manufacturing processes, heavy metals and radioactivity sometimes. Along with oil and due to its high volume production, water production is one of the pollutants of most concern in the process of oil extraction. PAHs due to their ubiquity and their characteristics carcinogenic or mutagenic and teratogenic even have attracted the attention of every scientific society. Formed from the incomplete combustion of organic matter may be natural or anthropogenic. Some materials have been researched with the goal of cleaning up environmental matrices that may be contaminated by hydrocarbons. Among these materials researched various clays have been employed, of which highlights the vermiculite. The family of phyllosilicates, vermiculite for its potential and its high hydrophobic surface area has been a tool widely used in the decontamination of water in processes of oil spills. However, when it loses its capacity expanded hydrophobic having the necessity of using a hidrofobizante to make it organophilic. Among the numerous hidrofobizantes researched and used the linseed oil was the pioneer. In this study sought to evaluate the capacity of removal of PAHs using the vermiculite hydrofobized with linseed oil and wax also, for it was made use of the 24 full factorial design as the main tool for the experiments. We also evaluated the clay grain size (-20 +48 and -48 +80 #), the percentage of hidrofobizante applied (5 and 10%) and salinity of the water produced synthesized in our laboratory (35,000 and 55,000 ppm). The molecular fluorescence spectroscopy due to its sensitivity and speed was used to verify the adsorption capacity of clay, as well as gas chromatography served as an auxiliary technique to identify and quantify the PAHs in solution. In order to characterize the vermiculite was made use of X-ray fluorescence and X-ray diffraction. The infrared and thermogravimetry were essential to note hydrophobization and the amount of coating of clay. According to the fluorescence analysis showed that the test 12 was the best result in about 98% adsorption of fluorescent compounds, however the high salinity, the smallest particle size, the highest percentage of hidrofobizante and the use of linseed oil showed greater efficiency in the removal capacity of these hydrocarbons, in accordance with the trend followed by the analysis of the major factors of the factorial design. To verify the adsorption capacity of clay using a fixed volume of water produced synthetically, used as the test base 12, at their respective levels and factors. Thus, it was observed that after adding about 1 ½ liters of water solution produced synthetically, about 300 times its volume in mass, the vermiculite was able to adsorb 80% of fluorescent species present in solution

Viabilidade técnica da fabricação de compósito utilizando fibra de pneu na fabricação de blocos intertravados

This work aims to demonstrate the feasibility of a ceramic composite containing fiber in the rubber manufacturing interlocking blocks. Gravel, sand, cement, rubber and fiber: the processes of manufacture and assembly of blocks produced and the various formulations studied with different proportions between the constituent elements were addressed. Mechanical properties were determined for the different formulations, compressive strength, diametral compressive strength, water absorption and apparent density, obeying the rules related to each property. It was concluded that the addition of rubber fiber gave the concrete studied resistance lower than conventional concrete which can be verified on the microstructural analysis obtained by SEM, which revealed the presence of pores and the low adhesion between the fiber and the matrix compression (tire fiber / cement paste). The composite of more viable tire BCPB1 (1/2) fiber can be used in places requests as light squares, pavements, roads and other cycle as well as in the manufacture of the curb and gutter, by having compressive strength in about 20 MPa

Caracterização mecânica, térmica e acústica de um compósito que utiliza rejeitos de mármore, granito e EPS para a fabricação de blocos para a construção civil

The use of composite materials for the construction industry has been the subject of numerous scientific papers in Brazil and in the world. One of the factors that motivate this quest is the housing deficit that countries especially the third world face. In Brazil this deficit reaches more than 6.5 million homes, around 12% of all US households . This paper presents a composite that was obtained from waste generated in processes for the production of granite and marble slabs, cement, gypsum, sand, crushed EPS and water. These wastes cause great damage to the environment and are thrown into landfi lls in bulk. The novelty of the work is in the combined study thermal, mechanical and acoustic composite obtained in real situation of rooms that are part of an experimental housing. Many blocks were made from cement compositions, plaster, foam, sand, marb le and / or granite, preliminary tests of mechanical and thermal resistance were made by choosing the most appropriate proportion. Will be given the manufacturing processes and assembly units 500 units 10 x 80 x 28 cm produced for the construction of an ex perimental home. We studied what kind of block and residue, marble or granite, made it more feasible for the intended purpose. The mechanical strength of the produced blocks were above 3.0 MPa. The thermal resistance of the blocks was confirmed by the maxi mum temperature difference between the inner and outer walls of rooms built around 8.0 ° C. The sound absorption for optimal room was around 31%. Demonstrated the feasibility of using the blocks manufactured with composite material proposed for construction.