Caracterização tectono-estratigráfica da sequência transicional na sub-bacia de Sergipe

This thesis deals with the tectonic-stratigraphic evolution of the Transitional Sequence in the Sergipe Sub-basin (the southern segment of the Sergipe-Alagoas Basin, Northeast Brazil), deposited in the time interval of the upper Alagoas/Aptian stage. Sequence boundaries and higher order internal sequences were identified, as well as the structures that affect or control its deposition. This integrated approach aimed to characterize the geodynamic setting and processes active during deposition of the Transitional Sequence, and its relations with the evolutionary tectonic stages recognized in the East Brazilian Margin basins. This subject addresses more general questions discussed in the literature, regarding the evolution from the Rift to the Drift stages, the expression and significance of the breakup unconformity, the relationships between sedimentation and tectonics at extensional settings, as well as the control on subsidence processes during this time interval. The tectonic-stratigraphic analysis of the Transitional Sequence was based on seismic sections and well logs, distributed along the Sergipe Sub-basin (SBSE). Geoseismic sections and seismic facies analysis, stratigraphic profiles and sections, were compiled through the main structural blocks of this sub-basin. These products support the depositional and tectonic-stratigraphic evolutionary models built for this sequence. The structural analysis highlighted similarities in deformation styles and kinematics during deposition of the Rift and Transitional sequences, pointing to continuing lithospheric extensional processes along a NW trend (X strain axis) until the end of deposition of the latter sequence was finished by the end of late Aptian. The late stage of extension/rifting was marked by (i) continuous (or as pulses) fault activity along the basin, controling subsidence and creation of depositional space, thereby characterizing upper crustal thinning and (ii) sagstyle deposition of the Transitional Sequence at a larger scale, reflecting the ductile stretching and thinnning of lower and sub crustal layers combined with an increasing importance of the thermal subsidence regime. Besides the late increments of rift tectonics, the Transitional Sequence is also affected by reactivation of the border faults of SBSE, during and after deposition of the Riachuelo Formation (lower section of the Transgressive Marine Sequence, of Albian age). It is possible that this reactivation reflects (through stress propagation along the newlycreated continental margin) the rifting processes still active further north, between the Alagoas Sub-basin and the Pernambuco-Paraíba Basin. The evaporitic beds of the Transitional Sequence contributed to the development of post-rift structures related to halokinesis and the continental margin collapse, affecting strata of the overlying marine sequences during the Middle Albian to the Maastrichtian, or even the Paleogene time interval. The stratigraphic analysis evidenced 5 depositional sequences of higher order, whose vertical succession indicates an upward increase of the base level, marked by deposition of continental siliciclastic systems overlain by lagunar-evaporitic and restricted marine systems, indicating that the Transitional Sequence was deposited during relative increase of the eustatic sea level. At a 2nd order cycle, the Transitional Sequence may represent the initial deposition of a Transgressive Systems Tract, whose passage to a Marine Transgressive Sequence would also be marked by the drowning of the depositional systems. At a 3rd order cycle, the sequence boundary corresponds to a local unconformity that laterally grades to a widespread correlative conformity. This boundary surface corresponds to a breakup unconformity , being equivalent to the Pre-Albian Unconformity at the SBSE and contrasting with the outstanding Pre-upper Alagoas Unconformity at the base of the Transitional Sequence; the latter is alternatively referred, in the literature, as the breakup unconformity. This Thesis supports the Pre-Albian Unconformity as marker of a major change in the (Rift-Drift) depositional and tectonic setting at SBSE, with equivalent but also diachronous boundary surfaces in other basins of the Atlantic margin. The Pre-upper Alagoas Unconformity developed due to astenosphere uplift (heating under high lithospheric extension rates) and post-dates the last major fault pulse and subsequent extensive block erosion. Later on, the number and net slip of active faults significantly decrease. At deep to ultra deep water basin segments, seaward-dipping reflectors (SDRs) are unconformably overlain by the seismic horizons correlated to the Transitional Sequence. The SDRs volcanic rocks overly (at least in part) continental crust and are tentatively ascribed to melting by adiabatic decompression of the rising astenospheric mantle. Even though being a major feature of SBSE (and possibly of other basins), the Pre-upper Alagoas Unconformity do not correspond to the end of lithospheric extension processes and beginning of seafloor spreading, as shown by the crustal-scale extensional structures that post-date the Transitional Sequence. Based on this whole context, deposition of the Transitional Sequence is better placed at a late interval of the Rift Stage, with the advance of an epicontinental sea over a crustal segment still undergoing extension. Along this segment, sedimentation was controled by a combination of thermal and mechanical subsidence. In continuation, the creation of oceanic lithosphere led to a decline in the mechanical subsidence component, extension was transferred to the mesoceanic ridge and the newly-formed continental margin (and the corresponding Marine Sequence) began to be controlled exclusively by the thermal subsidence component. Classical concepts, multidisciplinary data and new architectural and evolutionary crustal models can be reconciled and better understood under these lines

Estratigrafia de sequências do intervalo aptiano ao albino na Bacia do Araripe, NE do Brasil

This study has as a main objective to make a detailed stratigraphic analysis of the Aptian-Albian interval in the east part of Araripe Basin, NE of Brazil which correspond, litostratigraphically, to Rio Da Batateira, Crato, Ipubi and Romualdo formations. The stratigraphic analysis was based on three different stages, the 1D, 2D and 3D analysis; these ones were adapted to the sequence stratigraphy concepts in order to create a chronostratigraphic framework for the study area within the basin. The database used in the present study contains field and well information, wells that belong to Santana Project, carried out by the Ministério de Minas e Energia- DNPM- CPRM from 1977 to 1978. The analysis 1D, which was done separately for each well and outcrop allowed the recognition of 13 sedimentary facies, mainly divided based on predominant litologies and sedimentary structures. Such facies are lithologically represented by pebble, sandstones, claystones, margas and evaporates; these facies are associated in order to characterize different depositional systems, that integrate from the continental environment (fluvial system and lacustre), paralic system (delta system and lagunar) to the marine environment (shelfenvironment). The first one, the fluvial system was divided into two subtypes: meandering fluvial system, characterized by fill channel and floodplain deposits; the facies of this system are associated vertically according to the textural thinning upward cycles (dirting-up trend pattern in well logs). Lacustrine environment is mainly related with the lithotypes of the Crato Formation, it shows a good distribution within the basin, been composed by green claystone deposits and calcareous laminated. Deltaic System represented by prodelta and delta front deposits which coarsening upward tendency. Lagunar system is characterised by the presence of anhydrite and gypsum deposits besides the black claystone deposits with vegetal fragments which do not contain a fauna typically marine. The marine platform system is composed by successions of black and gray claystone with fossiliferous fauna of Dinoflagellates (Spiniferites Mantell, Subtilisphaera Jain e Subtilisphaera Millipied genre) typical of this kind of depositional system. The sedimentary facies described are vertically arranged in cycles with progradational patterns which form textural coersening upward cycles and retrogradational, represented by textural thinning dowward cycles. Based in these cycles, in their stack pattern and the vertical change between these patterns, the systems tracks and the depositional sequences were recognized. The Low System Track (LST) and High System Track (HST) are composed by cycles with progradational stack pattern, whereas the Trangessive System Track (TST) is composed by retrogradational stack pattern cycles. The 2D stratigraphic analysis was done through the carrying out of two stratigraphic sections. For the selection of the datum the deepest maximum flooding surface was chosen, inside the Sequence 1, the execution of these sections allowed to understand the behaviour of six depositional systems along the study area, which were interpreted as cycles of second order or supercycles (cycles between 3 and 10 Ma), according to the Vail, et al (1977) classification. The Sequence 1, the oldest of the six identified is composed by the low, transgressive and high systems tracks. The first two system tracks are formed exclusively by fluvial deposits of the Rio da Batateira Formation whereas the third one includes deltaic and lacustrine deposits of the Crato Formation. The sequences 2 and 3 are formed by the transgressive systems tracks (lake spreading phase) and the highstand system track (lake backward phase). The TST of these sequences are formed by lacustrine deposits whereas HST contains deltaic deposits, indicating high rates of sedimentary supply at the time of it s deposition. The sequence 4 is composed by LST, TST and HST, The TST4 shows a significant fall of the lake base level, this track was developed in conditions of low relation between the creation rate of space of accommodation and the sedimentary influx. The TST4 marks the third phase of expansion of the lacustrine system in the section after the basin´s rift, the lacustrine system established in the previous track starts a backward phase in conditions that the sedimentary supply rate exceeds the creation rate of space accommodation. The sequence 5 was developed in two different phases, the first one is related with the latest expansion stage of the lake, (TST5), the basal track of this sequence. In this phase the base level of the lake rose considerably. The second phase (related to the TST5) indicates the end of the lacustrine domain in the Araripe Basin and the change to lagunar system ant tidal flat, with great portions in the supratidal. These systems were formed by restricted lagoons, with shallow level of water and with intermittent connections with the sea. This, was the phase when the Araripe Basin recorded the most several arid conditions of the whole interval studied, Aptian Albian, conditions that allow the formation of evaporitic deposits. The sequence 6 began its deposition after a significant fall of the sea (LST6). The sequence 6 is without any doubtlessly, the sequence that has deposits that prove the effective entrance of the sea into the Araripe Basin. The TST6, end of this sequence, represents the moment which the sea reaches its maximum level during the Aptian Albian time. The stratigraphic analysis of the Aptian Albian interval made possible the understanding that the main control in the development of the depositional sequences recognized in the Araripe Basin were the variations of the local base level, which are controlled itself by the climate changes

Implementação de processador banda base ofdma para downlink lte em fpga

This work treats of an implementation OFDMA baseband processor in hardware for LTE Downlink. The LTE or Long Term Evolution consist the last stage of development of the technology called 3G (Mobile System Third Generation) which offers an increasing in data rate and more efficiency and flexibility in transmission with application of advanced antennas and multiple carriers techniques. This technology applies in your physical layer the OFDMA technical (Orthogonal Frequency Division Multiple Access) for generation of signals and mapping of physical resources in downlink and has as base theoretical to OFDM multiple carriers technique (Orthogonal Frequency Division Multiplexing). With recent completion of LTE specifications, different hardware solutions have been developed, mainly, to the level symbol processing where the implementation of OFDMA processor in base band is commonly considered, because it is also considered a basic architecture of others important applications. For implementation of processor, the reconfigurable hardware offered by devices as FPGA are considered which shares not only to meet the high requirements of flexibility and adaptability of LTE as well as offers possibility of an implementation quick and efficient. The implementation of processor in reconfigurable hardware meets the specifications of LTE physical layer as well as have the flexibility necessary for to meet others standards and application which use OFDMA processor as basic architecture for your systems. The results obtained through of simulation and verification functional system approval the functionality and flexibility of processor implemented

Síntese, sinterização e caracterização de ferritas à base de Ni-Zn

Were synthesized different ferrites NixZn1-xFe2O4 (0,4 ≤ x ≤ 0,6) compositions by using citrate precursor method. Initially, the precursors citrates of iron, nickel and zinc were mixed and homogenized. The stoichiometric compositions were calcined at 350°C without atmosphere control and the calcined powders were pressed in pellets and toroids. The pressed material was sintered from 1100º up to 1200ºC in argon atmosphere. The calcined powders were characterized by XRD, TGA/DTG, FTIR, SEM and vibrating sample magnetometer (VSM). All sintered samples were characterized using XRD, SEM, VSM and measurements of magnetic permeability and loss factor were obtained. It was formed pure ferromagnetic phase at all used temperatures. The Rietveld analyses allowed to calculate the cations level occupation and the crystallite size. The analyses obtained nanometric crystals (12-20 nm) to the calcined powder. By SEM, the sintered samples shows grains sizes from 1 to 10 μm. Sintered densities (ρ) were measured by the Archimedes method and with increasing Zn content, the bulk density decrease. The better magnetization results (105-110 emu/g) were obtained for x=0,6 at all sintering temperatures. The hysteresis shows characteristics of soft magnetic material. Two magnetization processes were considered, superparamagnetism at low temperature and the magnetic domains formation at high temperatures. The sintered toroids presents relative magnetic permeability (μr) from 7 to 32 and loss factor (tanδ) of about 1. The frequency response of toroids range from 0,3 kHz to 0,2 GHz. The composition x=0,5 presents both greater μr and tanδ values and x=0,6 the most broad range of frequency response. Various microstructural factors show influence on the behavior of μr and tanδ, such as: grain size, porosity across grain boundary and inside the grain, grain boundary content and domain walls movement during the process of magnetization at high frequency studies (0,3kKz 0,2 GHz)

Análise comparativa na influência da técnica de moldagem funcional em arcos parcialmente edêntulos sobre os pontos de contato oclusais, a integridade da fibromucosa e a extensão da base da prótese

There is a lack of clinical studies evaluating techniques of functional impression for partially edentulous arches. The aim of this double-blind non-randomized controlled clinical trial was to compare the efficacy of altered cast impression (ACI) and direct functional impression (DFI) techniques. The efficacy was evaluated regarding the number of occlusal units on denture teeth, mucosa integrity at 24-hour follow-up and denture base extension. The sample included 51 patients (female and male) with mean age of 58.96 years treated at Dental Department of UFRN. The patients, exhibiting edentulous maxilla and mandibular Kennedy class I, were divided into two groups (group ACI, n=29; group DFI, n=22). Clinical evaluation was based on the number of occlusal units on natural and/or artificial teeth, mucosa integrity at 24-hour follow-up, and denture base extension. Statistical analysis was conducted using the software SPSS 17.0® (SPSS Inc., Chicago, Illinois). Student T-test was used to reveal association between number of occlusal units and impression technique while chi-square test showed association between mucosa integrity and impression technique. Fischer s exact test was applied for association between denture base extension and impression technique at 95% level of significance. No significant difference was observed between the groups regarding number of occlusal units, mucosa integrity and denture base extension. The altered cast technique did not provide significant improvement in comparison to the direct technique when the number of occlusal units, mucosa integrity and denture base extension

BSmart: desenvolvimento rigoroso de aplicações Java Card com base no método formal B

Java Card technology allows the development and execution of small applications embedded in smart cards. A Java Card application is composed of an external card client and of an application in the card that implements the services available to the client by means of an Application Programming Interface (API). Usually, these applications manipulate and store important information, such as cash and confidential data of their owners. Thus, it is necessary to adopt rigor on developing a smart card application to improve its quality and trustworthiness. The use of formal methods on the development of these applications is a way to reach these quality requirements. The B method is one of the many formal methods for system specification. The development in B starts with the functional specification of the system, continues with the application of some optional refinements to the specification and, from the last level of refinement, it is possible to generate code for some programming language. The B formalism has a good tool support and its application to Java Card is adequate since the specification and development of APIs is one of the major applications of B. The BSmart method proposed here aims to promote the rigorous development of Java Card applications up to the generation of its code, based on the refinement of its formal specification described in the B notation. This development is supported by the BSmart tool, that is composed of some programs that automate each stage of the method; and by a library of B modules and Java Card classes that model primitive types, essential Java Card API classes and reusable data structures

Geração de processos WS-BPEL com base em um algoritmo de reescrita de regras

Web services are computational solutions designed according to the principles of Service Oriented Computing. Web services can be built upon pre-existing services available on the Internet by using composition languages. We propose a method to generate WS-BPEL processes from abstract specifications provided with high-level control-flow information. The proposed method allows the composition designer to concentrate on high-level specifi- cations, in order to increase productivity and generate specifications that are independent of specific web services. We consider service orchestrations, that is compositions where a central process coordinates all the operations of the application. The process of generating compositions is based on a rule rewriting algorithm, which has been extended to support basic control-flow information.We created a prototype of the extended refinement method and performed experiments over simple case studies

Interpretação de dados de GPR com base na hierarquização de superfícies limitantes e na adaptação de critérios sismoestratigráficos

Due to its high resolution, Ground Penetrating Radar (GPR) has been used to image subsurface sedimentary deposits. Because GPR and Seismic methods share some principles of image construction, the classic seismostratigraphic interpretation method has been also applied as an attempt to interpret GPR data. Nonetheless some advances in few particular contexts, the adaptations from seismic to GPR of seismostratigraphic tools and concepts unsuitable because the meaning given to the termination criteria in seismic stratigraphy do not represent the adequate geologic record in the GPR scale. Essentially, the open question relies in proposing a interpretation method for GPR data which allow not only relating product and sedimentary process in the GPR scale but also identifying or proposing depositional environments and correlating these results with the well known Sequence Stratigraphy cornerstones. The goal of this dissertation is to propose an interpretation methodology of GPR data able to perform this task at least for siliciclastic deposits. In order to do so, the proposed GPR interpretation method is based both on seismostratigraphic concepts and on the bounding surface hierarchy tool from Miall (1988). As consequence of this joint use, the results of GPR interpretation can be associated to the sedimentary facies in a genetic context, so that it is possible to: (i) individualize radar facies and correlate them to the sedimentary facies by using depositional models; (ii) characterize a given depositional system, and (iii) determine its stratigraphic framework highligthing how it evolved through geologic time. To illustrate its use the proposed methodology was applied in a GPR data set from Galos area which is part of the Galinhos spit, located in Rio Grande do Norte state, Northeastern Brazil. This spit presents high lateral sedimentary facies variation, containing in its sedimentary record from 4th to 6th cicles caused by high frequency sea level oscillation. The interpretation process was done throughout the following phases: (i) identification of a vertical facies succession, (ii) characterization of radar facies and its associated sedimentary products, (iii) recognition of the associated sedimentary process in a genetic context, and finally (iv) proposal of an evolutionay model for the Galinhos spit. This model proposes that the Galinhos spit is a barrier island constituted, from base to top, of the following sedimentary facies: tidal channel facies, tidal flat facies, shore facies, and aeolic facies (dunes). The tidal channel facies, in the base, is constituted of lateral accretion bars and filling deposits of the channels. The base facies is laterally truncated by the tidal flat facies. In the foreshore zone, the tidal flat facies is covered by the shore facies which is the register of a sea transgression. Finally, on the top of the stratigraphic column, aeolic dunes are deposited due to areal exposition caused by a sea regression

Beachrocks do Rio Grande Do norte: correlação entre os depósitos costeiros e os de zona costa-afora com base na faciologia, petrografia e diagênese

Beachrocks são rochas sedimentares formadas pela cimentação de sedimentos praiais por carbonato de cálcio em especial, calcita e/ou aragonita em zona de estirâncio. A ocorrência dessas rochas é bastante comum em diversas partes do globo, sobretudo em regiões com latitudes inferiores a 40º. O Rio Grande do Norte possui grande quantidade de beachrocks, os quais afloram tanto em regiões costeiras quanto em zona costa-afora. Os depósitos de beachrocks de zona costeira do referido estado têm sido estudados por diversos autores, os quais abordaram os mais variados temas desde o início do século XX. Por outro lado, os depósitos de zona costa-afora apesar de terem sido estudados por poucos autores têm ganhado atenção apenas nos últimos anos. Porém, nenhum trabalho até o presente fez algum tipo de estudo comparativo de cunho geológico entre os corpos de beachrocks presentes em ambas as zonas: costeira e costa-afora. Sendo assim, a presente dissertação teve o intuito de correlacionar os corpos de beachrocks que afloram em zona costeira aos que estão atualmente dispostos em zona costa-afora, próximo a isóbata de 25 m, levando em consideração seus aspectos petrográficos, diagenéticos e sedimentológicos. Para isso, foram percorridos cerca de 260 km de litoral, correspondendo ao trecho entre os municípios de Extremoz e Tibau, em busca de afloramentos de beachrocks. Seções colunares foram confeccionadas e amostras coletadas em estações de amostragem representativas da zona costeira, ao passo que da zona costa-afora apenas seções delgadas foram analisadas. Trabalhos disponíveis na literatura sobre o tema e área em pauta também foram utilizados. A partir dos dados levantados, observou-se que os beachrocks são formados por diferentes camadas ao longo de um perfil vertical. Estas camadas são claramente identificadas em afloramento pela diferença existente na composição, textura e estruturas sedimentares peculiares a cada uma delas. Seções delgadas foram confeccionadas e analisadas a partir de amostras coletadas nas diferentes camadas de diversos afloramentos. Um afloramento foi escolhido como afloramento modelo sendo este o de São Bento do Norte por apresentar a maior espessura de rocha aflorante (1,9 m). Este tem sido muito bem estudado tanto no corrente trabalho quanto em trabalhos de outros autores. A este foram comparados todos os outros afloramentos analisados. A partir da análise micropetrográfica, foram identificadas 03 microfácies para os beachrocks do Rio Grande do Norte, sendo elas: Quartzarenítica (< 2,9% de bioclastos), Quartzarenítica Bioclástica (entre 3 e 9,9% de bioclastos) e Bio-quartzarenítica (> 10% de bioclastos). Associando essas microfácies às análises sedimentológicas realizadas foi possível propor que as microfácies Quartzarenítica e Bio-quartzarenítica foram depositadas em zona de estirâncio enquanto que a microfácies Quartzarenítica Bioclástica foi depositada em zona de face litorânea superior. A história diagenética dos beachrocks estudados é marcada por quatro principais processos: compactação mecânica, cimentação, dissolução e geração de porosidade secundária, e oxidação. Dentre esses, o processo de cimentação é o mais importante, sendo caracterizado por precipitação de cimento de calcita rica em Mg sob cinco morfologias, a saber: cutículas criptocristalinas, franjas prismáticas isópacas, calcita espática microcristalina, calcita espática equante e agregados pseudo-peloidais. Todas estas morfologias foram formadas durante o estágio de eodiagênese, nas zonas freática marinha ativa ou freática meteórica ativa, corroborando assim com a idéia de que beachrocks têm sua litificação completa a pequenas profundidades. Associando as análises microfaciológicas às diagenéticas foi possível sugerir que a sucessão vertical de camadas vista em alguns beachrocks costeiros representam registros de variações de mais alta frequência do nível do mar durante o Holoceno. A partir daí, baseando-se em informações obtidas através de curvas de variação do nível do mar relativo no Holoceno para o Rio Grande do Norte, disponíveis na literatura, e na correlação aqui realizada entre os beachrocks costeiro e aqueles de zona costa-afora, foi possível inferir que estes últimos representam uma antiga linha de costa formada a idades relativas superiores a 7.000 anos A.P

Classificação de técnicas e auxílio à navegação de busca com base em sua carga cognitiva, precisão e eficiência

Navigation, in both virtual and real environments, is the process of a deliberated movement to a specific place that is usually away from the origin point, and that cannot be perceived from it. Navigation aid techniques (TANs) have as their main objective help finding a path through a virtual environment to a desired location and, are widely used because they ease the navigation on these unknown environments. Tools like maps, GPS (Global Positioning System) or even oral instructions are real world examples of TAN usage. Most of the works which propose new TANs for virtual environments aim to analyze their impact in efficiency gain on navigation tasks from a known place to an unknown place. However, such papers tend to ignore the effect caused by a TAN usage over the route knowledge acquisition process, which is important on virtual to real training transfer, for example. Based on a user study, it was possible to confirm that TANs with different strategies affects the performance of search tasks differently and that the efficiency of the help provided by a TAN is not inversely related to the cognitive load of the technique’s aids. A technique classification formula was created. This formula utilizes three factors instead of only efficiency. The experiment’s data were applied to the formula and we obtained a better refinement of help level provided by TANs.