Análise microestrutural de misturas cerâmicas de grês porcelanato com adição de chamote de telhas cerâmicas

MELO, Maxymme Mendes de ; PINHEIRO, Andrea Santos ; NASCIMENTO, R. M. ; MARTINELLI, Antonio Eduardo ; DUTRA, Ricardo Peixoto Suassuna ; MELO, Marcus Antônio de Freitas . Análise microestrutural de misturas cerâmicas de grês Porcelanato com adição de chamote de telhas cerâmicas. Cerâmica (São Paulo. Impresso), v. 55, p. 356-364, 2009

Preparação e caracterização de catalisadores à base de titânio suportado em MCM-41 para produção de compostos oxigenados através da pirólise catalítica do capim elefante

In recent years, the area of advanced materials has been considerably, especially when it comes to materials for industrial use, such as is the case with structured porosity of catalysts suitable for catalytic processes. The use of catalysts combined with the fast pyrolysis process is an alternative to the oxygenate production of high added value, because, in addition to increasing the yield and quality of products, allows you to manipulate the selectivity to a product of interest, and therefore allows greater control over the characteristics of the final product. Based on these arguments, in this work were prepared titanium catalysts supported on MCM-41 for use in catalytic pyrolysis of biomass, called elephant grass. The reactions of pyrolysis of biomass were performed in a micro pyrolyzer, Py-5200, coupled to GC / MS, the company CDS Corporation, headquartered in the United States. The catalysts Ti-MCM-41 in different molar ratios were characterized by XRD, TG / DTG, FT-IR, SEM, XRF, UV-visible adsorption of nitrogen and the distribution of particle diameter and specific surface area measurement by the BET method. From the catalytic tests it was observed that the catalysts synthesized showed good results for the pyrolysis reaction.The main products were obtained a higher yield of aldehydes, ketones and furan. It was observed that the best reactivity is a direct function of the ratio Si/Ti, nature and concentration of the active species on mesoporous supports. Among the catalysts Ti-MCM-41 (molar ratio Si / Ti = 25 and 50), the ratio Si / Ti = 25 (400 ° C and 600 ° C) favored the cracking of oxygenates such as acids , aldehydes, ketones, furans and esters. Already the sample ratio Si / Ti = 50 had the highest yield of aromatic oxygenates

Pirólise térmica e catalítica de resíduos de vácuo gerados no refino de petróleo

In this study, was used a very promising technique called of pyrolysis, which can be used for obtaining products with higher added value. From oils and residues, since the contribution of heavier oils and residues has intensified to the world refining industry, due to the growing demand for fuel, for example, liquid hydrocarbons in the range of gasoline and diesel. The catalytic pyrolysis of vacuum residues was performed with the use of a mesoporous material belonging the M41S family, which was discovered in the early 90s by researchers Mobil Oil Corporation, allowing new perspectives in the field of catalysis. One of the most important members of this family is the MCM-41, which has a hexagonal arrangement of mesopores with pore diameters between 2 and 10 nm and a high specific surface area, making it very promising for use as a catalyst in petroleum refining for catalytic cracking, and their mesopores facilitate the access of large hydrocarbon molecules. The addition of aluminum in the structure of MCM-41 increases the acidity of the material, making it more positive for application in the petrochemical industry. The mesoporous material of the type Al-MCM41 (ratio Si / Al = 50) was synthesized by hydrothermal method starting from the silica gel, NaOH and distilled water added to the gel pseudobohemita synthesis. Driver was used as structural CTMABr. Removal of organic driver (CTMABr) was observed by TG / DTG and FTIR, but this material was characterized by XRD, which was observed the formation of the main peaks characteristic of mesoporous materials. The analysis of adsorption / desorption of nitrogen this material textural parameters were determined. The vacuum residues (VR's) that are products of the bottom of the vacuum distillation tower used in this study are different from oil fields (regions of Ceará and Rio de Janeiro). Previously characterized by various techniques such as FTIR, viscosity, density, SARA, elemental analysis and thermogravimetry, which was performed by thermal and catalytic degradation of vacuum residues. The effect of AlMCM-41 was satisfactory, since promoted a decrease in certain ranges of temperature required in the process of conversion of hydrocarbons, but also promoted a decrease in energy required in the process. Thus enabling lower costs related to energy expenditure from degradation during processing of the waste

A gestão do conhecimento e a inovação tecnológica como fatores de sobrevivência e de competitividade na sociedade do conhecimento: uma análise exploratória das MPEs do Rio Grande do Norte

The study examines the process of Knowledge Management and Technological Innovation in Small and Micro Enterprises (SME) in Rio Grande do Norte, Brazil, and proposes actions that can contribute to regional development and competitiveness of SME. Presents as technological innovation can help to make the SME entrepreneurial activities with innovative and competitive. Defines the phases and activities of the construction of knowledge in small organizations. Examines the process of Innovation, Research and Development (R & D) in SME. Identifies the use of knowledge management and technological innovation in management practices and social interaction to influence the competitiveness of SME. Covers the communities of practice as a diffuser of knowledge and learning. To obtain the data were used questionnaires with closed questions with multiple choice, direct observations and interviews with companies. The questionnaires and interviews covered the topics of Innovation, Knowledge Management and Competitive Intelligence on SME. The sample consisted of a total of 13 Small and Micro Enterprises Award winning MPE Brazil Competitiveness, sponsored by SEBRAE in the State of Rio Grande do Norte. The assessment questionnaires dealing with the Knowledge Management (KM Diagnostics - Model Bukowitz and Williams, 2002) and the process of Technological Innovation (Adaptation of ANPEI - National Association for Research, Development and Engineering of Innovative Companies). With the analysis, we concluded that the SME perceive knowledge management, but not formalized management practices so as to facilitate the dissemination of information. Soon, these companies need additional supports to direct them to the innovative activities that generate added value and competitiveness in the market

Produção de grês porcelanato a partir de matérias-primas do Rio Grande do Norte e queima a gás natural

The State of Rio Grande do Norte, Brazil, possess major deposits of feldspar, clay, kaolin and talc, all raw materials used in the production of porcelainized stoneware tiles. Conversely, state industries manufacture only low added value red ceramics. Porcelainized stoneware tiles is one of the noblest ceramics, depicting low water absorption (typically below of 0,5%), in addition to excellent staining resistance and mechanical strength. The present work aims at investigating the potential of local raw materials for the production of porcelainized stoneware tiles. To that end, these materials were characterized by X-ray fluorescence, X-ray diffraction, particle size analysis, thermal gravimetric analysis and thermal differential analysis. Admixtures containing different compositions were prepared and fired at three temperatures, 1150, 1200 and 1250°C for 30 min. After firing, tests samples were characterized by water absorption tests, linear retraction, dilatometric analysis, apparent porosity, apparent specific mass, flexural strength, and microstructural analysis by XRD and SEM. The results revealed that ceramics with porcelainized stoneware tiles characteristics could be produced from raw materials originated in the State of Rio Grande do Norte

Estudo da viabilidade técnica do uso das argilas da região do agreste potiguar para produção de peças cerâmicas: caracterização e formulação

In recent decades, ceramic products have become indispensable to the technological development of humanity, occupying important positions in scientific production and consequently in industrial production. One area of the economy that continues to absorb large amounts of the products of this sector is Construction. Among the branches of the ceramic industry, there are the red ceramic industry which is traditionally the basis of that economic sector. Among the reasons for which the red ceramic industry became popular in the country, and specifically in Rio Grande do Norte, is the abundance of this raw material, easily found throughout the national territory. However, it appears that the red ceramic industry has deficiencies in technology and skilled labor, resulting in the production of ceramic goods with low added value. Among the factors that determine the quality of the ceramic products red has the proper formulation of the ceramic mass, the conformation and the firing temperature. Thus, the overall goal of this work is to study the mineralogical and technological properties, two clays from the region of the Wasteland Potiguar industrial ceramist. Therefore, the raw materials were characterized by analysis of Xray diffraction (XRD) analysis, X-ray fluorescence (XRF), particle size analysis (FA), scanning electron microscopy (SEM), optical microscopy (OM ), plasticity index (PI), thermal gravimetric analysis (TGA) and differential thermal analysis (DTA). The technological properties of the material were analyzed by water absorption tests (AA%) porosity (% PA), the linear shrinkage (RT%), apparent density (MEA), loss on ignition (PF%) and flexural strength three points (TRF)

Estudo do potencial refratário de argilas sílico-aluminosas do Rio Grande do Norte

The segment of the structural ceramics industry is one of the most important to the economy of Rio Grande do Norte. The supply chain makes a total of 206 companies that are distributed in 39 counties, concentrated in three regional centers: Seridó Apodi / Assu and great Natal. The ceramic industry in the state is around 80 million pieces per month, with 50,186 million of these tiles, which makes the Rio Grande do Norte one of the largest manufacturers of product in the Country. Different ceramic products can be manufactured by mixing two or more clays and accessory minerals. Mixtures acquire characteristics and form what is called the ceramic body. Refractory masses have a high melting point and thermal shock support. Its composition contains refractory clays with a little iron oxide and material fluxes. A line of semi-refractory ceramic products that stands out for its high added value are the bricks in ivory or red, used in building barbecues, fireplaces, wood stoves and braziers. The aim of this study was to use alumina-clay or silica- alumina-clay to the industrial RN, for the production of refractory bricks semi-refractory burning light. Clay and Kaolin were characterized for their chemical and mineralogical composition, immediately after ceramic bodies were made with different concentrations of the components, they were raised, pressed and sintered. After sintering the resulting products were characterized in terms of mechanical, thermal and dimensional than the characterization by X-ray diffraction and scanning electron microscopy. After obtaining the results, we concluded that the studied clay can be used for the production of semi-refractory bricks

Influência do estresse nutricional programado na composição da microalga isochrysis galbana

Global warming due to Greenhouse Gases (GHG) emissions, especially CO2, has been identified as one of the major problems of the twenty-first century, considering the consequences that could represent to planet. Currently, biological processes have been mentioned as a possible solution, especially CO2 biofixation due to association microalgae growth. This strategy has been emphasized as in addition to CO2 mitigation, occurs the production of biomass rich in compounds of high added value. The Microalgae show high photosynthetic capacity and growth rate higher than the superior plants, doubling its biomass in one day. Its culture does not show seasons, they grow in salt water and do not require irrigation, herbicides or pesticides. The lipid content of these microorganisms, depending on the species, may range from 10 to 70% of its dry weight, reaching 90% under certain culture conditions. Studies indicate that the most effective method to promote increased production of lipids in microalgae is to induce stress by limiting nitrogen content in the culture medium. These evidences justify research continuing the production of biofuels from microalgae. In this paper, it was studied the strategy of increasing the production of lipids in microalgae I. galbana with programmed nutritional stress, due to nitrogen limitation. The physiological responses of microalgae, grown in f / 2 with different concentrations of nitrogen (N: P 15,0-control, N: 5,0 P and N: P 2,5) were monitored. During exponential phase, results showed invariability in the studied conditions. However the cultures subjected to stress in stationary phase, showed lower biomass yields. There was an increase of 32,5% in carbohydrate content and 87.68% in lipids content at N: P ratio of 5,0 and an average decrease of 65% in protein content at N: P ratios of 5, 0 and 2.5. There were no significant variations in ash content, independently of cultivation and growth phase. Despite the limitation of biomass production in cultures with N: P smaller ratios, the increase of lipid accumulation highest lipids yields were observed as compared to the control culture. Given the increased concentration of lipids associated to stress, this study suggests the use of microalgae Isochrysis galbana as an alternative raw material for biofuel production

Análise técnica e econômica do processo de obtenção de espaguetes com adição de farinha de trigo integral e farinha de linhaça

This work studies the fabrication of spaghetti through the process at high temperatures through the use of flour added to flour and flaxseed meal, with the aim of evaluating the final product quality and estimate the cost of production. The values of moisture, ash, protein, wet gluten, gluten index, falling number and grain of flour and mixtures to test to be the possible use in mass manufacturing and technological criteria for compliance with current legislation. Spaghetti noodles type were manufactured by adding 10% and 20% flour and 10% and 20% flaxseed meal with performance of physical-chemical, sensory and rheological properties of the products. Further analysis was performed on the product acceptance and estimation of production cost in order to create subsidies to enable the introduction of products with greater acceptance and economic viability in the market by the food industry. On the rheology of the product test was cooking the pasta, specifying the volume increase, cooking time and percentage of solid waste. In the sensory evaluation was carried out the triangular test of product differentiation with 50 trained judges and acceptance testing by a hedonic scale with evaluation of the aspects color, taste, smell and texture. In defining the sensory profile of the product was performed with ADQ 9 judges recruited and trained at the factory, using unstructured scale of 9 cm, assessing the attributes of flavor of wheat, flax flavor, consistency, texture of raw pasta, raw pasta color and color of cooked pasta. The greater acceptance of product quality was good and the pasta with 20% flour, 10% followed by the full product, 10% and 20% flaxseed characterized the average quality of the criterion of loss analysis of solids, together with mass full commercial testing. In assessing the estimated cost of production, the two products more technologically feasible and acceptable (20% whole and 10% flaxseed) were evaluated in high temperature processes. With total cost of R $ 4,872.5 / 1,000 kg and R $ 5,354.9 / 1,000 kg respectively, the difference was related to the addition of lower inputs and higher added value in the market, flour and flaxseed meal. The comparative analysis of cases was confirmed the reduction in production time (10h), more uniform product to the drying process at high temperature compared to conventional

Avaliação de catalisadores a base de carbeto e nitreto de molibdênio na obtenção de lactitol via hidrogenação da lactose

Seeking a greater appreciation of cheese whey was developed to process the hydrogenation of lactose for the production of lactitol, a polyol with high added value, using the catalyst Ni / activated carbon (15% and 20% nickel), the nitride Mo2N, the bimetallic carbide Ni-Mo/ activated carbon and carbide Mo2C. After synthesis, the prepared catalysts were analyzed by MEV, XRD, laser granulometry and B.E.T. The reactor used in catalytic hydrogenation of lactose was the type of bed mud with a pressure (68 atm), temperature (120 oC) and stirring speed (500 rpm) remained constant during the experiments. The system operated in batch mode for the solid and liquid and semi-continuous to gas. Besides the nature of the catalyst, we studied the influence of pH of reaction medium for Mo2C carbide as well as evaluating the character of the protein inhibitor and chloride ions on the activity of catalysts Ni (20%)/Activated Carbon and bimetallic carbide Ni-Mo/Activated Carbon. The decrease in protein levels was performed by coagulation with chitosan and adsorption of chloride ions was performed by ion exchange resins. In the process of protein adsorption and chloride ions, the maximum percentage extracted was about 74% and 79% respectively. The micrographs of the powders of Mo2C and Mo2N presented in the form of homogeneous clusters, whereas for the catalysts supported on activated carbon, microporous structure proved impregnated with small particles indicating the presence of metal. The results showed high conversion of lactose to lactitol 90% for the catalyst Ni (20%)/Activated Carbon at pH 6 and 46% for the carbide Mo2C pH 8 (after addition of NH4OH) using the commercial lactose. Monitoring the evolution of the constituents present in the reaction medium was made by liquid chromatography. A kinetic model of heterogeneous Langmuir Hinshelwood type was developed which showed that the estimated constants based catalysts promoted carbide and nitride with a certain speed the adsorption, desorption and production of lactitol

Gestão de estoques: uma proposta de reposição contínua para material médico hospitalar e medicamentos em um hospital universitário federal do estado do Rio Grande do Norte

The inventory management in hospitals is of paramount importance, since the supply materials and drugs interruption can cause irreparable damage to human lives while excess inventories involves immobilization of capital. Hospitals should use techniques of inventory management to perform replenishment in shorter and shorter intervals, in order to reduce inventories and fixed assets and meet citizens requirements properly. The inventory management can be an even bigger problem for public hospitals, which have restrictions on the use of resources and decisionmaking structure more bureaucratized. Currently the University Hospital Onofre Lopes (HUOL) uses a periodic replacement policy for hospital medical supplies and medicines, which involves one moment surplus stock replenishment, the next out of stock items. This study aims to propose a system for continuous replenishment through order point for inventory of medical supplies and medicines to the hospital HUOL. Therefore, a literature review of Federal University Hospitals Management, Logistics, Inventory Management and Replenishment System in Hospitals was performed, emphasizing the demand forecast, classification or ABC curve and order point system. And also, policies of inventory management and the current proposal were described, dealing with profile of the mentioned institution, the current policy of inventory management and simulation for continuous replenishment order point. For the simulation, the sample consisted of 102 and 44 items of medical and hospital drugs, respectively, selected using the ABC classification of inventory, prioritizing items of Class A, which contains the most relevant items in added value, representing 80 % of the financial value in 2012 fiscal year. Considering that it is a public organization, subject to the laws, we performed two simulations: the first, following the signs for inventory management of Instruction No. 205 (IN 205 ), from Secretary of Public Administration of the Presidency ( SEDAP / PR ), and the second, based on the literature specializing in inventory management hospital. The results of two simulations were compared to the current policy of replenishment system. Among these results are: an indication that the system for continuous replenishment reorder point based on IN 205 provides lower levels of safety stock and maximum stock, enables a 17% reduction in the amount spent for the full replenishment of inventories, in other words, decreasing capital assets, as well as reduction in stock quantity, also the simulation made from the literature has indicated parameters that prevent the application of this technique to all items of the sample. Hence, a change in inventory management of HUOL, with the application of the continuous replenishment according to IN 205, provides a significant reduction in acquisition costs of medical and hospital medicine

Síntese hidrotérmica e caracterização estrutural de titanatos nanotubulares para aplicação na captura do dióxido de carbono

Nanostructured materials have been spreading successfully over past years due its size and unusual properties, resulting in an exponential growth of research activities devoted to nanoscience and nanotechnology, which has stimulated the search for different methods to control main properties of nanomaterials and make them suitable for applications with high added value. In the late 90 s an alternative and low cost method was proposed from alkaline hydrothermal synthesis of nanotubes. Based on this context, the objective of this work was to prepare different materials based on TiO2 anatase using hydrothermal synthesis method proposed by Kasuga and submit them to an acid wash treatment, in order to check the structural behavior of final samples. They were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), adsorption/desorption of N2, thermal analysis (TG/DTA) and various spectroscopic methods such as absorption spectroscopy in the infrared (FT-IR), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). All the information of characterizations confirmed the complete conversion of anatase TiO2 in nanotubes titanates (TTNT). Observing the influence of acid washing treatment in titanates structure, it was concluded that the nanotubes are formed during heat treatment, the sample which was not subjected to this process also achieved a complete phase transformation, as showed in crystallography and morphology results, however the surface area of them practically doubled after the acid washing. By spectroscopy was performed a discussion about chemical composition of these titanates, obtaining relevant results. Finally, it was observed that the products obtained in this work are potential materials for various applications in adsorption, catalysis and photocatalysis, showing great promise in CO2 capture

Viabilidade da cultura Cnidoscolus quercifolius POHL para produção de Biodiesel no semiárido nordestino

The northeastern semiarid is a region that presents a serious picture stagnation or slowness of the economic growth, beyond the presence of social pointers below of the averages national and regional. The half-dryness conditions become the improper region for many agricultural cultures, what it affects the local populations directly, as well as the economy that is based mainly on agriculture. Cnidoscolus quercifolius Pohl, popularly know as favelone is a native species of the semiarid region that withholds great potential for the development of the region in virtue of its multiple uses. Being an oleaginous, its production in familiar farmings makes with that biodiesel either for the misery an important alternative eradication for the possibility of occupation of enormous contingents of people. The present study it aims at to evaluate the germination of the faveleira without thorns under conditions of water and saline stresses, main stresses which the vegetal species of the semiarid one are submitted; beyond verifying the acceptance of the species for agriculturists of a cooperative in the city of Apodi/RN. The methodology used for germination corresponds to using treatments with polyethylene glycol and sodium chloride to assess water and salt stress respectively, being held in rolo. O system approach used for the verification of acceptance of faveleira was the use of interview with farmers cooperative in the study area determined. In this direction it was verified that the faveleira is a resistant species the conditions of drought and salinity of the ground, factor of great relevance, since one is about a species with high added value, making possible the development for the semiarid region. It was verified that the agriculturists are favorable the introduction of the faveleira and reveal receptive the idea to cultivate a species with potential for production of biodiesel

Secagem de resíduo de goiaba em secador convectivo de bandejas: modelagem matemática e análise do processo

Actually, Brazil is one of the larger fruit producer worldwide, with most of its production being consumed in nature way or either as juice or pulp. It is important to highlig ht in the fruit productive chain there are a lot lose due mainly to climate reasons, as well as storage, transportation, season, market, etc. It is known that in the pulp and fruit processing industy a yield of 50% (in mass) is usually obtained, with the other part discarded as waste. However, since most this waste has a high nutrient content it can be used to generate added - value products. In this case, drying plays an important role as an alternative process in order to improve these wastes generated by the fruit industry. However, despite the advantage of using this technique in order to improve such wastes, issues as a higher power demand as well as the thermal efficiency limitation should be addressed. Therefore, the control of the main variables in t his drying process is quite important in order to obtain operational conditions to produce a final product with the target specification as well as with a lower power cost. M athematical models can be applied to this process as a tool in order to optimize t he best conditions. The main aim of this work was to evaluate the drying behaviour of a guava industrial pulp waste using a batch system with a convective - tray dryer both experimentally and using mathematical modeling. In the experimental study , the dryin g carried out using a group of trays as well as the power consume were assayed as response to the effects of operational conditions (temperature, drying air flow rate and solid mass). Obtained results allowed observing the most significant variables in the process. On the other hand, the phenomenological mathematical model was validated and allowed to follow the moisture profile as well as the temperature in the solid and gas phases in every tray. Simulation results showed the most favorable procedure to o btain the minimum processing time as well as the lower power demand.

Estudo de simulação de reservatórios para o desenvolvimento de um campo do nordeste brasileiro

In the last 16 years emerged in Brazil a segment of independent producers with focus on onshore basins and shallow waters. Among the challenges of these companies is the development of fields with projects with a low net present value (NPV). The objective of this work was to study the technical-economical best option to develop an oil field in the Brazilian Northeast using reservoir simulation. Real geology, reservoir and production data was used to build the geological and simulation model. Due to not having PVT analysis, distillation method test data known as the true boiling points (TBP) were used to create a fluids model generating the PVT data. After execution of the history match, four development scenarios were simulated: the extrapolation of production without new investments, the conversion of a producing well for immiscible gas injection, the drilling of a vertical well and the drilling of a horizontal well. As a result, from the financial point of view, the gas injection is the alternative with lower added value, but it may be viable if there are environmental or regulatory restrictions to flaring or venting the produced gas into the atmosphere from this field or neighboring accumulations. The recovery factor achieved with the drilling of vertical and horizontal wells is similar, but the horizontal well is a project of production acceleration; therefore, the present incremental cumulative production with a minimum rate of company's attractiveness is higher. Depending on the crude oil Brent price and the drilling cost, this option can be technically and financially viable.