Influência da formação de pozolanas com adição de metacaulim em concreto de alta resistência

The need to build durable structures and resistant to harsh environments enabled the development of high strength concrete, these activities generate a high cement consumption, which implies factor in CO2 emissions. Often the desired strength is not achieved using only the cement composition. This study aims to evaluate the influence of pozzolans with the addition of metakaolin on the physical mechanics of high strength concrete comparing them with the standard formulation. Assays were performed to characterize the aggregates according to NBR 7211, evaluation of cement and coarse aggregate through the trials of petrography (NBR 15577-3/08) and alkali-aggregate reaction (NBR 15577-05/08). Specimens were fabricated according to NBR 5738-1/04 with additions of 0%, 4%, 6%, 8% and 10% of metakaolin for cement mortars CP V in the formulations. For evaluation of the concrete hardened in fresh state and scattering assays were performed and compressive strength in accordance with the NBR 7223/1992 and NBR 5739-8/94 respectively. The results of the characterization of aggregates showed good characteristics regarding size analysis and petrography, as well as potentially innocuous as the alkali-aggregate reaction. As to the test of resistance to compression, all the formulations with the addition of metakaolin showed higher value at 28 days of disruption compared with the standard formulation. These results present an alternative to reduce CO2 emissions, and improvements in the quality and durability of concrete, because the fine particle size of metakaolin provides an optimal compression of the mass directly influencing the strength and rheology of the dough

Estudo da incorporação de resíduo industrial polimérico ao CAP

This work presents the incorporation of an industrial polymeric waste into a petroleum asphalt cement with penetration grade 50-60 (CAP 50-60). The main goal of this research is the development of a polymer-modified asphalt, with improvements in its physical properties, in order to obtain a more resistant material to the traffic loads. Furthermore, the use of this polymeric waste will result in economic and environmental benefits. The CAP 50-60 used in this research was kindly supplied by LUBNOR Lubrificantes e Derivados de Petróleo do Nordeste (produced in Fazenda Belém Aracati - Ceará) and the industrial polymeric waste was provided by a button manufacturer industry, located in Rio Grande do Norte state. This polymeric waste represents an environmental problem due to its difficulty in recycling and disposal, being necessary the payment by the industry to a landfill. The difficulty in its reuse is for being this material a termofixed polymer, as a result, the button chips resulting from the molding process cannot be employed for the same purpose. The first step in this research was the characterization of the polymeric waste, using Differential Scanning Calorimetry (DSC) Infrared spectroscopy (IR spectroscopy), and Thermogravimetric analysis (TGA). Based on the results, the material was classified as unsaturated polyester. After, laboratory experiments were accomplished seeking to incorporate the polymeric waste into the asphalt binder according to a 23 experimental factorial design, using as main factors: the polymer content (2%, 7% and 14%), the temperature of the mixture (140 and 180 oC) and the reaction time (20 and 60 minutes). The characterization of the polymer-modified asphalt was accomplished by traditional tests, such as: penetration, ring and ball softening point, viscosity, ductility and flash point temperature. The obtained results demonstrated that the addition of the polymeric waste into the asphalt binder modified some of its physical properties. However, this addition can be considered as a feasible alternative for the use of the polymeric waste, which is a serious environmental and technological problem.

Reciclagem de material asfáltico fresado utilizando solventes e microemulsões

With the increase of asphalt milling services was also a significant increase in recycling services pavements. The techniques used today are basically physical processes in which the milled material is incorporated into new asphalt mixtures or executed on site, with the addition of virgin asphalt and rejuvenating agent. In this paper seeks to analyze the efficiency of extraction of CAP (Petroleum Asphalt Cement) mixtures from asphalt milling, using commercial solvents and microemulsions. The solvents were evaluated for their ability to solubilize asphalt using an extractor reflux-type apparatus. Pseudoternary diagrams were developed for the preparation of microemulsion O/W surfactant using a low-cost coconut oil saponified (OCS). Microemulsions were used to extract the CAP of asphalt through physicochemical process cold. Analysis was performed concentration of CAP in solution by spectroscopy. The data provided in the analysis of concentration by the absorbance of the solution as the basis for calculating the percentage of extraction and the mass flow of the CAP in the solution. The results showed that microemulsions prepared with low concentration of kerosene and butanol/OCS binary has high extraction power of CAP and its efficiency was higher than pure kerosene, reaching 95% rate of extraction

Desenvolvimento de sistemas de pastas leves para aplicação em cimentação de poços petrolíferos com baixo gradiente de fratura

All around the world, naturally occurring hydrocarbon deposits, consisting of oil and gas contained within rocks called reservoir rocks , generally sandstone or carbonate exists. These deposits are in varying conditions of pressure and depth from a few hundred to several thousand meters. In general, shallow reservoirs have greater tendency to fracture, since they have low fracture gradient, ie fractures are formed even with relatively low hydrostatic columns of fluid. These low fracture gradient areas are particularly common in onshore areas, like the Rio Grande do Norte basin. During a well drilling, one of the most favorable phases for the occurrence of fractures is during cementing, since the cement slurry used can have greater densities than the maximum allowed by the rock structure. Furthermore, in areas which are already naturally fractured, the use of regular cement slurries causes fluid loss into the formation, which may give rise to failures cementations and formation damages. Commercially, there are alternatives to the development of lightweight cement slurries, but these fail either because of their enormous cost, or because the cement properties were not good enough for most general applications, being restricted to each transaction for which the cement paste was made, or both reasons. In this work a statistical design was made to determine the influence of three variables, defined as the calcium chloride concentration, vermiculite concentration and nanosilica concentration in the various properties of the cement. The use of vermiculite, a low density ore present in large amounts in northeastern Brazil, as extensor for cementing slurries, enabled the production of stable cements, with high water/cement ratio, excellent rheological properties and low densities, which were set at 12.5 lb / gal, despite the fact that lower densities could be achieved. It is also seen that the calcium chloride is very useful as gelling and thickening agent, and their use in combination with nanosilica has a great effect on gel strength of the cement. Hydrothermal Stability studies showed that the pastes were stable in these conditions, and mechanical resistance tests showed values of the order of up to 10 MPa

Obtenção de emulsões asfálticas convencionais e modificadas com argilas e nanoargilas

The increasing demand for asphalt leads to the development of techniques that can improve the quality of products and increase the useful working life of pavements. Consequently, there is a growing application of asphalt emulsions, which are produced from a mixture of petroleum asphalt cement (CAP) with an aqueous phase. The main advantage of asphalt emulsions is its cold application, reducing energy costs. Conventional emulsions are obtained using asphalt, water, solvent, and additives. The modified asphalt emulsion is developed by adding a modifying agent to conventional emulsions. These modifiers can be natural fibers, waste polymers, nanomaterials. In this work modified asphalt emulsion were obtained using organoclays. First, it was prepared a conventional asphalt emulsion with the following mass proportion: 50% of 50/70 penetration grade CAP, 0.6% of additives and 3% of emulsifier, 20% of solvent and 26.4% of water. It was used bentonite and vermiculite (1% and 4%) to obtain the modified asphalt emulsion. Bentonite and vermiculite were added in its raw state and as an organoclay form and as an organoclay-acid form, resulting in 26 experimental runs. The methodology described by Qian et al. (2011), with modifications, was used to obtain the organoclay and the organoclay-acid form. infrared spectroscopy (IR)) were used to characterize the clays and nanoclays. The emulsions were prepared in a colloidal mill, using 30 minutes and 1 hour as mixing time. After, the emulsions were characterized. The following tests were performed, in accordance with the Brazilian specifications (DNER- 369/97): sieve analysis, Saybolt Furol viscosity, pH determination, density, settlement and storage stability, residue by evaporation, and penetration of residue. Finally, it can be concluded that the use of nanoclays as asphalt modifiers represent a viable alternative to the road paving industry

Obtenção de emulsões asfálticas modificadas utilizando resíduos industriais

The main objective of this research was the development and characterization of conventional and modified cationic asphalt emulsions. The asphalt emulsions were developed by using the Petroleum Asphalt Cement (CAP 50-70) from Fazenda Belém (Petrobras -Aracati-Ce). The first step in this research was the development of the oil phase (asphalt + solvent) and the aqueous phase (water + emulsifying agent + acid + additives), separately. During the experiments for the obtaining of the conventional asphalt emulsion, the concentration of each constituent was evaluated. For the obtaining of the oil phase, kerosene was used as solvent at 15 and 20 wt.%. For the development of the aqueous phase, the emulsifying agent was used at 0.3 and 3.0 wt.%, whereas the acid and the additive were set at 0.3 wt.%. The percentage of asphalt in the asphalt emulsion was varied in 50, 55, and 60 wt.% and the heating temperature was set at 120 °C. The aqueous phase in the asphalt emulsion was varied from 16.4 to 34.1 wt.% and the heating temperature was set at 60 °C. After the obtaining of the oil and the aqueous phases, they were added at a colloidal mill, remaining under constant stirring and heating during 15 minutes. Each asphalt emulsion was evaluated considering: sieve analysis, Saybolt Furol viscosity, pH determination, settlement and storage stability, residue by evaporation, and penetration of residue. After the characterization of conventional emulsions, it was chosen the one that presented all properties in accordance with Brazilian specifications (DNER-EM 369/97). This emulsion was used for the development of all modified asphalt emulsions. Three polymeric industrial residues were used as modifier agents: one from a clothing button industry (cutouts of clothing buttons) and two from a footwear industry (cutouts of sandals and tennis shoes soles), all industries located at Rio Grande do Norte State (Brazil).The polymeric residues were added into the asphalt emulsion (1 to 6 wt.%) and the same characterization rehearsals were accomplished. After characterization, it were developed the cold-mix asphalts. It was used the Marshall mix design. For cold-mix asphalt using the conventional emulsion, it was used 5, 6 and 7 wt.% asphalt emulsion. The conventional mixtures presented stability values according Brazilian specification (DNER-369/97). For mixtures containing asphalt modified emulsions, it was observed that the best results were obtained with emulsions modified by button residue

Incorporação do lodo de tanque séptico como matéria-prima de uma mistura asfáltica

In Natal/RN, 68% of the population uses some kind of individual system for their domestic sewers treatment, being that the most used it is septic tank, followed by sumidouro. Every treatment system of sewers, usually used, generates a by-product denominated sludge. That residue presents some components, in its constitution, undesirable under the environmental and sanitary point of view. In such case, to assure that the system treatment has satisfactory results, it is necessary to do the adjusted disposition of the sludge sewage. Several countries are looking for technical alternatives for the use and disposition of residues. Under technical and environmental conditions appropriate, these materials can be used, decreasing the consumption of the natural resources and the treatment need, storage or elimination of the wastes, what decrease the risks created. Some of the alternatives of recycling of the sludge sewage are: the application in the agriculture, in the production of energy and as raw material in the civil construction. This study evaluated asphalt mixtures behavior that partially substituted conventional aggregates by septic tank sludge. The septic tank sludge gave origin to two raw materials called raw sludge and sludge ash. The raw sludge was put as a small aggregate and the sludge ash as filler. In the first experiment it was made a comparison between the mixture with conventional aggregates and the mixtures that replaced sand by raw sludge in the proportions from 5% to 40%. In the second experiment, it was made comparison between mixtures with 1%, 2% and 3% of sludge ash and cement. The stages developed along the study were: physical characterization of the conventional materials; physical, chemistry, thermal, mineralogical characterizations and analysis of environmental risk of the raw sludge; physical characterization and analysis of environmental risk of the sludge ash; analysis of the mixtures performance through its volumetric and mechanical characteristics; forecast of the mixtures susceptibility in the moisture presence. For the grain size composition used and with the percentage asphalt adopted, the mixtures with up to 7,5% of raw sludge in his composition attend to the National Department of Transports Infrastructure (DNIT) specifications. However, in agreement with the mixtures susceptibility in the moisture presence, the mixtures with addition of raw sludge don't present satisfactory acting. In such case, they could be used in arid and semi-arid areas. The raw sludge application in mixtures increased their voids volume and their stability. However, it damaged mixtures adhesiveness. Mixtures with sludge ash and with cement presented similar behavior. However, mixtures with sludge ash presented a better performance than mixtures with cement as for their stability and their tensile strength ratio. The mixture with 1% of sludge ash is better. The wastes studied don't represent environmental risk

Desenvolvimento de misturas ternárias para remoção de reboco de fluido de perfuração sintético

The construction of wells is one of the most important activities of the oil industry. The drilling process is the set of activities and operations to design, program and perform the opening thereof. During this process, the cuttings are removed by the drilling fluid, or mud, and carted to the surface. This fluid is injected into the drill string and returns to the surface through the annular space between the well walls and the drill string. After the descent of the column casing, the annular space between the casing string and the walls of the borehole is filled with cement so as to secure the spine and prevent any migration of fluids between the various permeable zones traversed by the well behind of the coating. To ensure the good quality of the cementation scrubbers are used mattresses which are pumped ahead of the cement slurry so as to avoid contamination of the drilling fluid paste, or vice versa, and assist in the removal of plaster, formed by drilling fluid of the borehole walls, thus enabling a better cement bond to the well. Within this context, this work aims to evaluate the efficiency of mattresses scrubbers, the basis of ionic and nonionic surfactants, on the removal of nonaqueous drilling fluid, based on n-paraffin in oil wells, and the compatibility between the Mattress relations washer / drilling fluid bed scrubber / cement paste mattress washer / cement slurry / drilling fluid and the drilling fluid / cement slurry using laboratory tests rheology, thickening time and compressive strength. Also technique was performed X-ray diffraction (XRD) for a more detailed analysis of these mixtures with hydrated cement paste. In compatibility tests the conditions of temperature and pressure used in the same laboratory procedure simulating the conditions of oil wells, the well is considered the depth of 800 m. The results showed that the compositions of the mattress washer nonionic, KMS obtained a 100% efficient in removing the non-aqueous drilling fluid, and the best formulation showed good results with respect to compliance testing

Qualidade de vida de pacientes com deformidade dentofacial

In the last decade, an increasing number of studies focusing on the impact of oral deformities on quality of life have been published. However, the evaluation of patients at different phases of the treatment has not been performed. Therefore, the purpose of this study was to determine the impact that dentofacial deformities have on patients` quality of life, as well as the influence exerted by social, economic, demographic and orthodontic factors, type and severity of malocclusion. A bicentric study - of the cross-sectional type of repeated panels - involving two cities - Natal and Rio de Janeiro - was carried out. A total of 227 patients participated in the study: 71 patients in the initial phase of the treatment (before any orthosurgical procedure), 115 patients in the pre-surgical (with braces) phase and 41 patients in the postoperative phase. The quality of life was measured using the Orthognatic Quality of Life Questionnnaire - OQLQ, translated and validated into Portuguese. The normative and aesthetic need for treatment was assessed with the Index of Orthodontic Treatment Need (IOTN) and the Dental Aesthetic Index (DAI); the social, economic and demographic factors, the type of service and malocclusion were also assessed. The data were analyzed through χ2/ Fisher`s exact test to seek the association between the nominal categorical variables in the three phases of treatment, Mann Whitney and Kruskal-Wallis test for gauging the existence of significant differences between two and three groups regarding each domain of OQLQ, respectively. For all tests, it was adopted a significance level of 5%. There was a statistically significant difference (p <0.001) in the general scores of OQLQ and in the domains of social aspects, facial aesthetics and oral function, when the "postoperative group" was compared to the "initial" and "orthodontic preparation" groups. Women, single, aged between 31 and 59 and living in Natal had the greatest impact on quality of life among patients in the "orthodontic preparation" group. Only the variable "income" (2 to 3 minimum wages), for the "initial" group, and gender (female) for the "postoperative" group, showed significant association with quality of life. The normative variable IOTN (DHC and AC) showed significant association with the OQLQ for the "initial" group, and the IOTN-AC-auto in the group of orthodontic preparation, being less important to women. We conclude that the ortho-surgical therapy has positive effects on quality of life after orthognathic surgery

Integrating strategic and sustainable design approach for innovation process: a cement case study

Global society and technology have changed the relationships of the market. Quality and cost are not the main aspects of any industrial product. On the other hand, design, innovation and sustainability became significant requirements to company’s competitiveness. In this context, the design approach has shown evolutions, integrating social and environmental aspects beside traditional aspects such as technical and economic. Still, design has been becoming a strategic opportunity for companies, improving their competitiveness and increasing their market share. Thus, this research has analyzed the integration of both the Sustainable Design and Strategic Design Coaching (SDC) method in the making decision activities of companies. A cement company (BQMIL) was assigned as case study, in which the previous results have pointed out the significant hole of those concepts to generate Eco-innovation and Eco-Brand to increase its market share, corroborating the expectative of the design team

A história do intemperismo na Província Borborema Oriental, Nordeste do Brasil: implicações paleoclimáticas e tectônicas

Until some years ago, weathering geochronology was primarily based on the K-Ar and 40Ar/39Ar dating of supergene minerals. Recent advances in the analysis of supergene goethite by the (U-Th)/He method expanded the number of suitable minerals for such purpose, as well as the time of application for weathering geochronology. This study represents the first systematic approach in Brazil, combining both the 40Ar/39Ar e (U-Th)/He methodologies to improve the knowledge on the weathering and the age of nonfossiliferous sediments. Supported by geologic and geomorphologic correlations, we identified different types of weathering profiles occurring in the interior and coastal areas of northeastern Brazil. These profiles were correlated to main regional geomorphological domains: the Borborema Plateau , the Sertaneja Depression , and the Coastal Cuestas and Plains, and respective planation surfaces, which study is fundamental to understand the landscape evolution of the northern portion of the eastern Borborema Province. The depth and stratigraphic organization of the weathering profiles in each of the geomorphological domains permitted to establish that: (i) the profiles on the highlands that cap the Borborema Surface are deeper (up to 100 m) and can be considered as typical lateritic profiles; (ii) on the lowlands that form the Sertaneja Surface , the weathering profiles are shallow and poorly developed (2-5 m deep); (iii) the profiles along the coastal area are moderately developed (up to 25 m deep), and are characterized by thick saprolites and mottle zones. Aiming to establish the timing of the evolution of northeastern Brazil, we studied 29 weathering profiles representing distinct topographic levels of the Borborema Province, from the highlands to the coast, through the analysis of 248 grains of supergene manganese oxides using laser step-heating 40Ar/39Ar geochronology. Additionally, we applied the (U-Th)/He method in 20 weathering profiles, by dating 171 grains of supergene iron oxides and hydroxides. Geochronological results for 248 grains of manganese oxides analyzed by the 40Ar/39Ar method indicate that the weathering profiles in the study area record the history of weathering from the Oligocene to the Pleistocene, with ages in the order of 31.4 ± 1.0 Ma to 0.8 ± 0.4 Ma. Dating of 171 grains of goethite by the (U-Th)/He method yielded ages ranging from 43.2 ± 4.3 Ma to 0.8 ± 0.1 Ma, suggesting the weathering processes last from the Eocene to the Pleistocene. The precipitation of supergene goethite in this interval confirms the age of the weathering processes identified from the manganese oxides record. 105 goethite grains from 8 different occurrences of the Barreiras Formation were dated by the (U-Th)/He method. Five grains collected from the cement in the Barreiras Formation sandstones, in the Lagoa Salgada and Rio do Fogo coastal cuestas, yielded ages of 17.6 ± 1.8 Ma, 17.3 ± 1.7 Ma, 16.3 ± 1.6 Ma, 16.2 ± 1.6 Ma and 13.6 ± 1.4 Ma. Results of 69 goethite grains from authigenic pisoliths collected in 7 different localities also yielded concordant ages, varying from 17.8 ± 1.8 to 7.5 ± 0.8 Ma. Results obtained from 31 detrital grains are concordant in 3 distinct localities (Lagoa Salgada, Praia da Garças e Ponta Grossa); they vary in the range of 43.2 ± 4.3 to 21.6 ± 2.2 Ma, and indicate that the maximum age for the Barreiras Formation deposition is around 22 Ma. 40Ar/39Ar results for 15 manganese oxides grains associated with the Barreiras Formation weathering profiles, in 3 different localities, vary from 13.1 ± 0.9 to 7.7 ± 0.4 Ma, in the same range of ages obtained by the (U-Th)/He method. The systematic application of the 40Ar/39Ar and (U-Th)/He methods, respectively for manganese oxides and goethites, show that the Barreiras Formation sediments were already deposited since ca. 17 Ma, and that the weathering processes were active until ca. 7 Ma ago. The ages obtained from manganese oxides collected in the Cenozoic basalts (Macau Formation) also reveal a weathering history between 19 and 7 Ma, pointing to hot and humid conditions during most of the Miocene. 40Ar/39Ar ages yielded by manganese oxides associated with the Serra do Martins Formation vary from 14.1 ± 0.4 to 10.5 ± 0.3 Ma. On the other hand, (U-Th)/He ages from iron oxides/hydroxides collected in the Serra do Martins Formation mesas vary from 20.0 ± 2.0 to 5.5 ± 0.6 Ma, indicating that those sediments are older than 20 Ma. 40Ar/39Ar and (U-Th)/He results produced in this study are in agreement with paleoclimatic interpretations based on stable isotopes and clay index values measured in the Atlantic Ocean sediments, validating the use of weathering geochronology to investigate paleoclimatic variations. The direct dating of the Barreiras Formation permitted, for the first time, confident inferences on the age of the brittle deformation recorded by this sedimentary unit in the Rio Grande do Norte and Ceará states. The first event, syn-deposition, occurred during the early Miocene; an younger event, related to the post-depositional deformation of the Barreiras Formation, is associated with tectonic activity from the very early Miocene to the Holocene. In agreement with data from other areas, results obtained in this study reveal that the depth and complexity of the weathering profiles reflect the time of exposition of such areas to the weathering agents close to the surface. However, there is no clear relationship between ages vs. altitude. The depth and the stratigraphic organization of weathering profiles in northeastern Brazil, contrary to the southeastern Brazil pattern, do not vary toward the coast. In our study area, field observations reveal the presence of ancient, thick and complex lateritic profiles preserved in the sedimentary mesas on the Borborema Plateau, as younger, narrow and incipient ones occur in the dissected areas. Geochronological results obtained for these profiles yielded older ages on the high altitudes, and younger ages in the lowlands, suggesting the scarp retreatment is the most reliable model to explain the regional landscape evolution. However, in the coastal lowlands, the relatively older ages obtained indicate that more complexes processes were involved in the modeling of the local relief

Estudos sedimentológicos e o contexto estrutural da formação Serra do Martins, nos platôs de Portalegre, Martins e Santana/RN

This dissertation deals with sedimentological and structural framework of the siliciclastic rock of the Serra do Martins Formation (FSM) in the Portalegre, Martins and Santana plateau, located to the south of Potiguar Basin, in the southwest and central Rio Grande do Norte state. This formation, regarded as of Oligo-Miocene age based on intrusive relations of the Miocene Macau volcanics, has a still disputable age due to the lack of appropriate bio and/or chronostratigraphic markers. The FSSM deposits crop out along 650 to 750 m high plateau, as a remanescent sedimentary cover directly overlying topographically uplifted pre-cambrian crystalline rocks. During the last decades, these deposits were interpreted according to a Tertiary paleoclimatic evolutionary model, associated to pedogenetic processes. The sedimentological characterization of the FSM was done through a detailed study of its facies, petrography and diagenetic features. The facies study was based on description of field relations, textures and structures, the piling up of the strata and their lateral variations. The FSM was deposited by an anastomosing to coarse-meandering fluvial system, including deposits of lag, cannel-fill, ouver-bank and flood plain. The petrographic composition of the sediments, coupled to their facies and paleocurrent directions, suggest a rather distal sourcearea, to the south of the present plateau. The diagenetic study identified an incipient grain mechanical compaction, pronounced dissolution of the framework, matrix and/or cement components, intense precipitation of kaolinite, silic and, eventually, iron oxides, besides mechanical infiltration of the clays. Most of these events, regarded in the literature as associated to near-surface conditions (eo or telodiagenesis), indicate the FSM sediments were never deeply buried. Topographic relations along longitudinal and transversal sections reaching the Potiguar Basin to the north identified regional dips that allow to discuss stratigraphic correlations between the FSM and the basin formations. The sedimentological features of the different units and the intrusive relations of the Macau volcanics were also considered in these correlations,which support the Oligo-Miocene age previously accepted for the FSM. Concerning the tectonic framework of the FSM, this work investigated the pre-cambrian to cretaceous heritage and the cenozoic deformation, allowing the recognition of pre-, sin and post-FSM structures. The crystalline basement, belonging to the Seridó Belt, displays NE and WNW foliation trends related to the Brasiliano-age ductile shear zones. In this terrain, brittle-ductile and brittle NE- and NW-trending structures, associated with extensional joints filled with pegmatites and quartz veins, are related to an E-W compression by the end of Brasiliano Cycle. The E-W joints and NE-trending fractures were reactivated by N-S to N-S to NW extension during late Jurassic to Cretaceous times, controlling the emplacement of the Rio Ceará-Mirim basic dyke swarm and the opening of the Potiguar rift basin

Beachrocks do Rio Grande Do norte: correlação entre os depósitos costeiros e os de zona costa-afora com base na faciologia, petrografia e diagênese

Beachrocks são rochas sedimentares formadas pela cimentação de sedimentos praiais por carbonato de cálcio em especial, calcita e/ou aragonita em zona de estirâncio. A ocorrência dessas rochas é bastante comum em diversas partes do globo, sobretudo em regiões com latitudes inferiores a 40º. O Rio Grande do Norte possui grande quantidade de beachrocks, os quais afloram tanto em regiões costeiras quanto em zona costa-afora. Os depósitos de beachrocks de zona costeira do referido estado têm sido estudados por diversos autores, os quais abordaram os mais variados temas desde o início do século XX. Por outro lado, os depósitos de zona costa-afora apesar de terem sido estudados por poucos autores têm ganhado atenção apenas nos últimos anos. Porém, nenhum trabalho até o presente fez algum tipo de estudo comparativo de cunho geológico entre os corpos de beachrocks presentes em ambas as zonas: costeira e costa-afora. Sendo assim, a presente dissertação teve o intuito de correlacionar os corpos de beachrocks que afloram em zona costeira aos que estão atualmente dispostos em zona costa-afora, próximo a isóbata de 25 m, levando em consideração seus aspectos petrográficos, diagenéticos e sedimentológicos. Para isso, foram percorridos cerca de 260 km de litoral, correspondendo ao trecho entre os municípios de Extremoz e Tibau, em busca de afloramentos de beachrocks. Seções colunares foram confeccionadas e amostras coletadas em estações de amostragem representativas da zona costeira, ao passo que da zona costa-afora apenas seções delgadas foram analisadas. Trabalhos disponíveis na literatura sobre o tema e área em pauta também foram utilizados. A partir dos dados levantados, observou-se que os beachrocks são formados por diferentes camadas ao longo de um perfil vertical. Estas camadas são claramente identificadas em afloramento pela diferença existente na composição, textura e estruturas sedimentares peculiares a cada uma delas. Seções delgadas foram confeccionadas e analisadas a partir de amostras coletadas nas diferentes camadas de diversos afloramentos. Um afloramento foi escolhido como afloramento modelo sendo este o de São Bento do Norte por apresentar a maior espessura de rocha aflorante (1,9 m). Este tem sido muito bem estudado tanto no corrente trabalho quanto em trabalhos de outros autores. A este foram comparados todos os outros afloramentos analisados. A partir da análise micropetrográfica, foram identificadas 03 microfácies para os beachrocks do Rio Grande do Norte, sendo elas: Quartzarenítica (< 2,9% de bioclastos), Quartzarenítica Bioclástica (entre 3 e 9,9% de bioclastos) e Bio-quartzarenítica (> 10% de bioclastos). Associando essas microfácies às análises sedimentológicas realizadas foi possível propor que as microfácies Quartzarenítica e Bio-quartzarenítica foram depositadas em zona de estirâncio enquanto que a microfácies Quartzarenítica Bioclástica foi depositada em zona de face litorânea superior. A história diagenética dos beachrocks estudados é marcada por quatro principais processos: compactação mecânica, cimentação, dissolução e geração de porosidade secundária, e oxidação. Dentre esses, o processo de cimentação é o mais importante, sendo caracterizado por precipitação de cimento de calcita rica em Mg sob cinco morfologias, a saber: cutículas criptocristalinas, franjas prismáticas isópacas, calcita espática microcristalina, calcita espática equante e agregados pseudo-peloidais. Todas estas morfologias foram formadas durante o estágio de eodiagênese, nas zonas freática marinha ativa ou freática meteórica ativa, corroborando assim com a idéia de que beachrocks têm sua litificação completa a pequenas profundidades. Associando as análises microfaciológicas às diagenéticas foi possível sugerir que a sucessão vertical de camadas vista em alguns beachrocks costeiros representam registros de variações de mais alta frequência do nível do mar durante o Holoceno. A partir daí, baseando-se em informações obtidas através de curvas de variação do nível do mar relativo no Holoceno para o Rio Grande do Norte, disponíveis na literatura, e na correlação aqui realizada entre os beachrocks costeiro e aqueles de zona costa-afora, foi possível inferir que estes últimos representam uma antiga linha de costa formada a idades relativas superiores a 7.000 anos A.P