990 resultados para CNPQ::CIENCIAS EXATAS E DA TERRA::MATEMATICA EM REDE NACIONAL
Resumo:
This study presents new stress orientations and magnitudes from the Potiguar basin in the continental margin of Brazil. We analyzed breakout and drilled induced fractures derived from resistivity image logs run in ten oil wells. We also used direct Shmin measurements determined from hydraulic fractures and rock strength laboratory analysis. In addition, we compared these results with 19 earthquake focal mechanisms located in the crystalline basement. We observed that stress directions and magnitudes change across the basin and its basement. In the basin, the SHmax gradient of 20.0 MPa/km and the SHmax/Shmin ratio of 1.154 indicate a normal stress regime from 0.5 to 2.0 km, whereas the SHmax gradient of 24.5MPa/km and the SHmax/Shmin ratio of 1.396 indicate a strike slip stress regime from 2.5 to 4.0 km. The deeper strike-slip stress regime in the basin is similar to the regime in the basement at 1-12 km deep. This stress regime transition is consistent with an incipient tectonic inversion process in the basin. We also noted that the SHmax direction rotates from NW SE in the western part of the Potiguar basin to E W in its central and eastern part, following roughly the shoreline geometry. It indicates that local factors, as density contrast between continental and oceanic crust and sediment loading at the continental shelf influence the stress field. The concentration of fluid pressure in faults of the lowpermeability crystalline basement and its implications to establish a critically stressed fault regime in the basement is also discussed
Resumo:
The seismic reflection is used on a large scale in oil exploration. In case of marine acquisition the presence of high impedance contrast at the interfaces water/air generates multiple reflections events. Such multiple events can mask primary events; thus from the interpretational viewpoint it is necessary to mitigate the multiples. In this manuscript we compare two methods of multiple attenuation: the predictive multichannel deconvolution (DPM) and the F-K filtering (FKF). DPM is based in the periodicity of the multiples while FKF is based in multiples and primaries splitting in F-K domain. DPM and FKF were applied in common-offset and CDP gathers, respectively. DPM is quite sensible to the correct identification of the period and size of the filter while FKF is quite sensible to an adequate choice of the velocity in order to split multiples and primaries events in the F-K domain. DPM is a method that is designed to act over a specific event. So, when the parameters are well selected, DPM is very efficient in removing the specified multiple. Then DPM can be optimized by applying it several times, each time with a different parameterization. A deficiency of DPM occurs when a multiple is superposed to a primary event: in this situation, DPM can attenuate also the primary event. On the other hand, FKF presents almost the same performance to all multiples that are localized in the same sector of the F-K domain. The two methods can be combined in order to take advantage of their associated potentials. In this situation, DPM is firstly applied, with a focus in the sea bed multiples. Then FKF is applied in order to attenuate the remaining multiples
Resumo:
This study deals with origin, sedimentary filling and fossil content of three tanks situated at Antônio Martins, Barcelona, Rui Barbosa, and Apodi counties, Rio Grande do Norte State. In addition, fossil materials from the Câmara Cascudo Museum - UFRN - Fundação Amigos do Lajedo Soledade - FALS, and from private ownership were investigated. The following families were identified: Megatberiidae, Gomphotheriidae, Mylodontidae, Equidae, Felidae, Canidae, Hydrochoeridae, Camelidae, Cervidae, Dasypodidae, Glyptodontidae, Macraucheniidae, Toxodontidae, and an undetermined Edentata Pilosa. The megafauna analysis indicated that herbivorc families occur mainly in tanks, whereas carnivore families occur in a vast proportion in an investigated ravine. Taphonomie analyses were limited to physical features because the vast majority of fossils were previously colleted without appropriate care for this kind of study. The main fossization processes were identified during diagenetie investigation. Permineralization is the most important process and replacement is the secondary one during fossilization. The study concluded that paleoenvironmental conditions during the late Pleistocene were more humid than the current one. Tropical savana, characterized by fields and cerrados , was the dominant vegetation
Resumo:
This study analyzed measurements of the aeolian transport using vertical sand traps across the field dunes of Jenipabu, in the municipality of Extremoz, Rio Grande do Norte state to the North of Natal city. These measurements were used as parameters for the sand aeolian transport in the region. Before the field trips a map of landscape units was made. Three visits to the field were done in September 2011 (field a - the 13th, field b - the 21st, field c - the 29th), period of the year with the highest wind speed, and another in December 8th, 2011 (field d ) when the wind speed starts to decrease. The sand traps used were of the type "I" with collecting opening of 25 cm from the surface level, and type "S" with collecting opening of 25 cm located 25 cm from the surface level in six collecting points in two of the visits (fields a and d ), and sand traps of the type "T" with the collecting opening of 50 cm from the surface level in the other field trips (fields "b" and "c"). A set of records was also collected by using a portable meteorological station complemented with information such as frequency and intensity of winds, precipitation and relative air humidity in the region, from the Estação Meteorológica de Natal , located 12 km from the study area. The sediments collected were treated and the data obtained permitted calculating the ratio of sediment transport. In September, the sedimentation ratio varied from 0.01 to 11.39 kg.m-1.h-1 and in December this ratio varied from 0.33 to 1.30 kg.m-1.h-1 in the type T collectors. In type I collectors they ranged from 0.01 to 11.39 kg.m-1.h-1, while the same parameters varied from 0.01 to 0.73 kg.m-1.h-1 in type S collector. Based on the statistical analysis done, we concluded that the sediment transport increased proportionally to the wind speed 25 cm from the surface. However, this is not true above 25 cm from the surface. The transport of sediments is more intense near the surface where sedimentation ratios greater than 10 kg.m-1.h-1 were found, whilst a maximum value of 3 kg.m-1.h-1 was observed 25 cm below the surface. The volume of sediments collected increases with the increasing wind speed at the surface level, whereas this relationship is opposed far away from that surface
Resumo:
Deformation bands are structures, developed in porous sandstones, that has small offsets and they are not shown on seismic section. The deformation bands of the pre and synrift sandstones of Araripe Basin were studied in outcrop, macroscopic and microscopic scales. The hierarchical, cinematic and spatial-geometric characteristics, and also the deformational mechanisms acting during its structural evolution were established too. In general, the mesoscopic scale observation allowed to discriminate deformation bands as singles or clusters in three main sets: NNE-SSW dextral; NE-SW normal (sometimes with strike-slip offset); and E-W sinistral; further a bed-parallel deformation bands as a local set. The microscopic characterization allowed to recognize the shearing and cataclastic character of such structures. Through the multi-scale study done in this work we verified that deformation bands analyzed were preferentially developed when sandstones under advanced stage of lithification. We also infer that the geometrical-spatial complexity of these bands, together with the presence of cataclastic matrix, can difficult the migration of fluids in reservoir rocks, resulting on their compartmentalization. Therefore, the study of deformation bands can aid researches about the structural evolution of sedimentary basin, as well as collaborate to understand the hydrodynamic behavior of reservoirs compartmented by these deformational structures
Resumo:
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior
Resumo:
In this paper we present the methodological procedures involved in the digital imaging in mesoscale of a block of travertines rock of quaternary age, originating from the city of Acquasanta, located in the Apennines, Italy. This rocky block, called T-Block, was stored in the courtyard of the Laboratório Experimental Petróleo "Kelsen Valente" (LabPetro), of Universidade Estadual de Campinas (UNICAMP), so that from it were performed Scientific studies, mainly for research groups universities and research centers working in brazilian areas of reservoir characterization and 3D digital imaging. The purpose of this work is the development of a Model Solid Digital, from the use of non-invasive techniques of digital 3D imaging of internal and external surfaces of the T-Block. For the imaging of the external surfaces technology has been used LIDAR (Light Detection and Range) and the imaging surface Interior was done using Ground Penetrating Radar (GPR), moreover, profiles were obtained with a Gamma Ray Gamae-spectômetro laptop. The goal of 3D digital imaging involved the identification and parameterization of surface geological and sedimentary facies that could represent heterogeneities depositional mesoscale, based on study of a block rocky with dimensions of approximately 1.60 m x 1.60 m x 2.70 m. The data acquired by means of terrestrial laser scanner made available georeferenced spatial information of the surface of the block (X, Y, Z), and varying the intensity values of the return laser beam and high resolution RGB data (3 mm x 3 mm), total points acquired 28,505,106. This information was used as an aid in the interpretation of radargrams and are ready to be displayed in rooms virtual reality. With the GPR was obtained 15 profiles of 2.3 m and 2 3D grids, each with 24 sections horizontal of 1.3 and 14 m vertical sections of 2.3 m, both the Antenna 900 MHz to about 2600 MHz antenna. Finally, the use of GPR associated with Laser Scanner enabled the identification and 3D mapping of 3 different radarfácies which were correlated with three sedimentary facies as had been defined at the outset. The 6 profiles showed gamma a low amplitude variation in the values of radioactivity. This is likely due to the fact of the sedimentary layers profiled have the same mineralogical composition, being composed by carbonate sediments, with no clay in siliciclastic pellitic layers or other mineral carrier elements radioactive
Resumo:
The Camorim Oilfield, discovered in 1970 in the shallow water domain of the Sergipe Sub-basin, produces hydrocarbons from the Carmópolis Member of the Muribeca Formation, the main reservoir interval, interpreted as siliciclastics deposited in an alluvial-fluvial-deltaic context during a late rifting phase of Neoaptian age, in the Sergipe-Alagoas Basin. The structural setting of the field defines different production blocks, being associated to the evolution of the Atalaia High during the rift stage and subsequent reactivations, encompassing NE-SW trending major normal faults and NWEW trending secondary faults. The complexity of this field is related to the strong facies variation due to the interaction between continental and coastal depositional environments, coupled with strata juxtaposition along fault blocks. This study aims to geologically characterize its reservoirs, to provide new insights to well drilling locations in order to increase the recovery factor of the field. Facies analysis based on drill cores and geophysical logs and the 3D interpretation of a seismic volume, provide a high resolution stratigraphic analysis approach to be applied in this geodynamic transitional context between the rift and drift evolutionary stages of the basin. The objective was to define spatial and time relations between production zones and the preferential directions of fluid flow, using isochore maps that represent the external geometry of the deposits and facies distribution maps to characterize the internal heterogeneities of these intervals, identified in a 4th order stratigraphic zoning. This work methodology, integrated in a 3D geological modelling process, will help to optimize well drilling and hydrocarbons production. This methodology may be applied in other reservoirs in tectonic and depositional contexts similar to the one observed at Camorim, for example, the oil fields in the Aracaju High, Sergipe Sub-basin, which together represent the largest volume of oil in place in onshore Brazilian basins
Resumo:
The tectonics activity on the southern border of Parnaíba Basin resulted in a wide range of brittle structures that affect siliciclastic sedimentary rocks. This tectonic activity and related faults, joints, and folds are poorly known. The main aims of this study were (1) to identify lineaments using several remotesensing systems, (2) to check how the interpretation based on these systems at several scales influence the identification of lineaments, and (3) to contribute to the knowledge of brittle tectonics in the southern border of the Parnaíba Basin. The integration of orbital and aerial systems allowed a multi-scale identification, classification, and quantification of lineaments. Maps of lineaments were elaborated in the following scales: 1:200,000 (SRTM Shuttle Radar Topographic Mission), 1:50,000 (Landsat 7 ETM+ satellite), 1:10,000 (aerial photographs) and 1:5,000 (Quickbird satellite). The classification of the features with structural significance allowed the determination of four structural sets: NW, NS, NE, and EW. They were usually identified in all remote-sensing systems. The NE-trending set was not easily identified in aerial photographs but was better visualized on images of medium-resolution systems (SRTM and Landsat 7 ETM+). The same behavior characterizes the NW-trending. The NS-and EW-trending sets were better identified on images from high-resolution systems (aerial photographs and Quickbird). The structural meaning of the lineaments was established after field work. The NEtrending set is associated with normal and strike-slip faults, including deformation bands. These are the oldest structures identified in the region and are related to the reactivation of Precambrian basement structures from the Transbrazilian Lineament. The NW-trending set represents strike-slip and subordinated normal faults. The high dispersion of this set suggests a more recent origin than the previous structures. The NW-trending set may be related to the Picos-Santa Inês Lineament. The NS-and EW-trending sets correspond to large joints (100 m 5 km long). The truncation relationships between these joint sets indicate that the EW-is older than the NS-trending set. The methodology developed by the present work is an excellent tool for the understanding of the regional and local tectonic structures in the Parnaíba basin. It helps the choice of the best remote-sensing system to identify brittle features in a poorly known sedimentary basin
Resumo:
The of Serrinha plutonic suite, northeastern portion of the Borborema Province (NE Brazil), is characterized by a voluminous and diversified magmatism of Neoproterozoic age, intrusive in the Archean to Paleoproterozoic gneissic-migmatitic basement of the São José de Campestre massif. Field relations and petrographic and geochemical data allowed us to individualize different lithologic types among this plutonic suite, which is represented by intermediate to mafic enclaves, porphyritic diorites, porphyritic granitoids, porphyritic granodiorites, microporphyritic granites and dykes/sheets of microgranite. The intermediate-to-mafic enclaves occur associated with porphyritic granitoids, showing mixture textures. The porphyrytic diorites occur as isolated bodies, generally associated with intermediate-to-mafic enclaves and locally as enclaves within porphyritic granites. The granodiorites represent mixing between an intermediate to mafic magma with an acidic one. The micropophyritic granites occur as isolated small bodies, generally deformed, while the microgranite dykes/sheets crosscut all the previous granitoids. A U-Pb zircon age of 576 + 3 Ma was obtained for the Serrinha granite. This age is interpreted as age of the peak of the regional ductile deformational event (D3) and of the associated the E-W Rio Jacu shear zone, which control the emplacement of the Neoproterozoic syntectonic plutons. The porphyrytic granitoids show monzogranitic composition, transitional between peraluminous and metaluminous types, typically of the high potassium subalkaline-calc-alkaline series. The intermediate-to-mafic enclaves present vary from quartz diorite to tonalite/granodiorite, with metaluminous, shoshonitic affinity. The diorites are generally quartz-monzodiorite in composition, with metaluminous, subalkaline affinity. They display coarse-grained, inequigranular, porphyrytic texture, with predominance of plagioclase phenocrystals immersed in a matrix composed of biotite and pyroxenes. The microporphyrytic granites are essentially monzogranites of fine- to medium-grained texture, whereas microgranite dikes/sheets varying from monzogranites to syenogranites, with fine to media texture, equigranular. The diversified magmatism occurring at a relatively small surface associated with shear zones, suggests lithospheric dimensions for such structures, with magma extractions from different depths within the lower crust and upper mantle. The geological, geochemical and geochronological characteristics of the Serrinha plutonic suite suggest a pos-collisional geodynamic context for the Neoproterozoic magmatism. Thermobarometric data show emplacement conditions in the range 5-6 kbar (AlTamphibole) and 730-740°C (plagioclase-amphibole) for the porphyrytic granitoids (Serrinha body) and the intermediate-to-mafic enclaves
Resumo:
Pyrometamorphism results from conditions of high temperatures and very low pressures provoked by the intrusion of hypabyssal basic bodies into sedimentary or metassedimentary hosting rocks. The onshore portion of the Potiguar Basin in NE Brazil offers examples of this type of metamorphism nearby the contacts of Paleogene to Neogene plugs, sills and dikes of diabases and basalts crosscutting sandstones, siltstones and shales of the Açu Formation (Albian-Cenomanian). The thermal effects over these rocks are reflected on textures and minerals assemblages that characterize the sanidinite facies of metamorphism, often with partial melting of the feldspathic and mica-rich matrix. The liquid formed is potassic and peraluminous, with variably colored rhyolitic glass (colorless, yellow, brown) comprising microcrystals of tridymite, sanidine and clinoenstatite, besides residual detrital clasts of quartz and rarely zircon, staurolite and garnet. Lenses of shale intercalated within the sandstones display crystallites of Fe-cordierite (sekaninaite), mullite, sanidine, armalcolite (Fe-Ti oxide) and brown spinel. The rocks formed due to the thermal effect of the intrusions are called buchites for which two types are herein described: a light one derived from feldspathic sandstone and siltstone protoliths; and a dark one derived from black shale protoliths. Textures indicating partial melting and minerals such as sanidine, mullite, tridymite and armalcolite strongly demonstrate that during the intrusion of the basic bodies the temperature reached 1,000-1,150°C, and was followed by quenching. Cooling of the interstitial melts has as consequences the closure of pores and decrease of the permeability of the protolith, which varies from about 17-11% in the unaffected rocks to zero in the thermally modified types. Although observed only at contacts and over small distances, the number of basic intrusions hosted within the Potiguar Basin in both onshore and offshore portions leaves opened the possibility of important implications of the thermal effects over the hydrocarbon exploration in this area as well in other Cretaceous and Paleozoic basins in Brazil
Resumo:
This work presents the results of the first imaging of continental slope adjacent to Potiguar Basin, in the equatorial Brazilian margin (NE Brazil). Swath bathymetry provided a complete coverage of seafloor between the upper and middle slope (100-1,300 m). Fifteen submarine canyons were mapped. The shape of the slope reflects in distinct spatial distribution of the canyons. The western area displays convex profiles which implied a greater amount of incisions by canyons. Some of them have gradient walls higher than 35°. They were classified according to location and morphology. The canyons with heads indenting shelf edge, association with a incised valley and a large fluvial system, high sinuosities, V shape, terraces along margins, further erosive features such as landslide and gullies allow to deduce a sandy-gravelly sedimentation. These canyons are associated with deposition of submarine fan systems that have been considered permeable hydrocarbon reservoirs. The presence of gullies, furrows and dunes demonstrates the role of bottom currents in the shaping of the slope. The enlargement of canyons and the change in the course when they cross the border fault imply that tectonic has also influenced in the morphology of deep waters environments of Potiguar Basin. The current sedimentation of continental slope is considered mixed because the sediments are composed of siliciclastics and bioclasts. Predominant siliciclastics are calcite, dolomite, quartz, and clay minerals. The presence of stable minerals (zircon, tourmaline and rutile), and fragmented bioclasts implies the contributions of Rivers Açu and Apodi
Resumo:
The northern coast of Rio Grande do Norte State (RN) shows areas of Potiguar basin with high activity in petroleum industry. With the goal of avoiding and reducing the accident risks with oil it is necessary to understand the natural vulnerability, mapping natural resources and monitoring the oil spill. The use of computational tools for environmental monitoring makes possible better analyses and decisions in political management of environmental preservation. This work shows a methodology for monitoring of environment impacts, with purpose of avoiding and preserving the sensible areas in oil contact. That methodology consists in developing and embedding an integrated computational system. Such system is composed by a Spatial Decision Support System (SDSS). The SDSS shows a computational infrastructure composed by Web System of Geo-Environmental and Geographic Information - SWIGG , the System of Environmental Sensibility Maps for Oil Spill AutoMSA , and the Basic System of Environmental Hydrodynamic ( SisBAHIA a System of Modeling and Numerical Simulating SMNS). In a scenario of oil spill occurred coastwise of Rio Grande do Norte State s northern coast, the integration of such systems will give support to decision agents for managing of environmental impacts. Such support is supplied through a system of supporting to spatial decisions
Resumo:
This work presents geophysical and geological results obtained in a dunefield located in the east coast of Rio Grande do Norte State, with the aim to recognize the aeolian body depositional geometries to a future geologic modeling of the aeolian petroliferous reservoirs. The research, which was done in blowouts region situated at Nisia Floresta Municipally, included the characterization of external geometries with GPS and internal geometry analysis by GPR. Data was integrated in GoCAD software, where it was possible the three-dimensional characterization and interpretation of the studied deposits. The interpretation of GPR profiling allowed identifying: First-order bounding surfaces that separated the aeolian deposits of the Barreiras Formation rocks; Second-order bounding surfaces, which limit dune generations and Third-order bounding surfaces, a reactivation surface. This classification was based and adapted by the Brookfield (1977) and Kocurek (1996) propose. Four radarfacies was recognized: Radarfacies 1, progradational reflectors correlated to foresets of the dunes, Radarfacies 2, plain parallels reflectors related to sand sheets, Radarfacies 3, plain parallels reflectors associated to reworking of the blowout dune crest and Radarfacies 4, mounded reflectors associated to vegetated mound of sand or objects buried in subsurface. The GPR and GPS methods was also employed to the monitoring of dunefields susceptible to human activities in Buzios Beach, where the constructions along the blowout region and the tourism are changing the natural evolution of the deposits. This fact possibly to cause negative impacts to the coastal zone. Data obtained in Dunas Park, a unit environmental conservation, was compared with information of the Buzios Beach. There is a major tendency of erosion in Buzios, specifically in blowout corridor and blowout dune
Resumo:
The brazilian marginal basins have a huge potential to generate and accumulate petroleum. Incised valleys which are eroded in response to a fall of relative sea level are related to potential reservoir as well, modern drowned-valley estuaries serve as harbors to petroleum and salt industries, fisheries, waste-disposal sites and recreational areas for a significant fraction of the world s population. The combined influence of these factors has produced a dramatic increase in research on modern and ancient incised-valley systems. This research is one expression of this interest. The integrated use of satellites images and high resolution seismic (bathymetry, sides scan sonar) was used on the Apodi River mouth-RN to characterizes the continental shelf This area is located at the Potiguar Basin in the NE Brazilian Equatorial Atlantic margin. Through bathymetric and side scan sonar data processing, a digital Terrain Model was developed, and a detailed geomorphologic analysis was performed. In this way was possible to recognize the geomorphologic framework and differents sismofacies, which may influence this area. A channel extending from the ApodiMossoró river mouth to the shelf edge dominates the investigated area. This structure can be correlated with the former river valley developed during the late Pleistocene sea level fall. This channel has two main directions (NW-SE and NE-SW) probably controlled by the Potiguar Basin structures. The western margin of the channel is relatively steep and pronounced whereas the eastern margin consists only of a gentle slope. Longitudinal bedforms and massive ridges also occur. The first are formed doe to the shelf sediment rework and the reef-like structures probably are relics of submerged beachrock-lines indicating past shoreline positions during the deglacial sea-level rise. The sub-bottom seismic data allow the identification of different sismic patterns and a marcant discontinuity, interpreted as the Upper