Desenvolvimento de uma unidade laboratorial para quantificação de BTX como poluentes atmosféricos, usando microextração em fase sólida

This dissertation aims the development of an experimental device to determine quantitatively the content of benzene, toluene and xylenes (BTX) in the atmosphere. BTX are extremely volatile solvents, and therefore play an important role in atmospheric chemistry, being precursors in the tropospheric ozone formation. In this work a BTX new standard gas was produced in nitrogen for stagnant systems. The aim of this dissertation is to develop a new method, simple and cheaper, to quantify and monitor BTX in air using solid phase microextraction/ gas chromatography/mass spectrometry (SPME/CG/MS). The features of the calibration method proposed are presented in this dissertation. SPME sampling was carried out under non-equilibrium conditions using a Carboxen/PDMS fiber exposed for 10 min standard gas mixtures. It is observed that the main parameters that affect the extraction process are sampling time and concentration. The results of the BTX multicomponent system studied have shown a linear and a nonlinear range. In the non-linear range, it is remarkable the effect of competition by selective adsorption with the following affinity order p-xylene > toluene > benzene. This behavior represents a limitation of the method, however being in accordance with the literature. Furthermore, this behavior does not prevent the application of the technique out of the non-linear region to quantify the BTX contents in the atmosphere.

Obtenção de emulsões asfálticas convencionais e modificadas com argilas e nanoargilas

The increasing demand for asphalt leads to the development of techniques that can improve the quality of products and increase the useful working life of pavements. Consequently, there is a growing application of asphalt emulsions, which are produced from a mixture of petroleum asphalt cement (CAP) with an aqueous phase. The main advantage of asphalt emulsions is its cold application, reducing energy costs. Conventional emulsions are obtained using asphalt, water, solvent, and additives. The modified asphalt emulsion is developed by adding a modifying agent to conventional emulsions. These modifiers can be natural fibers, waste polymers, nanomaterials. In this work modified asphalt emulsion were obtained using organoclays. First, it was prepared a conventional asphalt emulsion with the following mass proportion: 50% of 50/70 penetration grade CAP, 0.6% of additives and 3% of emulsifier, 20% of solvent and 26.4% of water. It was used bentonite and vermiculite (1% and 4%) to obtain the modified asphalt emulsion. Bentonite and vermiculite were added in its raw state and as an organoclay form and as an organoclay-acid form, resulting in 26 experimental runs. The methodology described by Qian et al. (2011), with modifications, was used to obtain the organoclay and the organoclay-acid form. infrared spectroscopy (IR)) were used to characterize the clays and nanoclays. The emulsions were prepared in a colloidal mill, using 30 minutes and 1 hour as mixing time. After, the emulsions were characterized. The following tests were performed, in accordance with the Brazilian specifications (DNER- 369/97): sieve analysis, Saybolt Furol viscosity, pH determination, density, settlement and storage stability, residue by evaporation, and penetration of residue. Finally, it can be concluded that the use of nanoclays as asphalt modifiers represent a viable alternative to the road paving industry

Microemulsões aplicadas ao tratamento de Óleos isolantes

Naphthenic lubricating oils are used in transformers with the purpose of promoting electrical insulation and dissipating heat. The working temperature range of these oils typically lies between 60°C and 90°C and their useful life is 40 years in average. In that temperature range, the oils are decomposed during operation, whereby a small fraction of polar compounds are formed. The presence of these compounds may induce failure and loss of physical, chemical and electrical properties of the oil, thus impairing the transformer operation. By removing these contaminants, one allows the oxidized insulating oil to be reused without damaging the equipment. In view of this, an investigation on the use of surfactants and microemulsions as extracting agents, and modified diatomite as adsorbent, has been proprosed in this work aiming to remove polar substances detected in oxidized transformer oils. The extraction was carried out by a simple-contact technique at room temperature. The system under examination was stirred for about 10 minutes, after which it was allowed to settle at 25°C until complete phase separation. In another experimental approach, adsorption equilibrium data were obtained by using a batch system operating at temperatures of 60, 80 and 100°C. Analytical techniques involving determination of the Total Acidity Number (TAN) and infrared spectrophotometry have been employed when monitoring the decomposition and recovery processes of the oils. The acquired results indicated that the microemulsion extraction system comprising Triton® X114 as surfactant proved to be more effective in removing polar compounds, with a decrease in TAN index from 0.19 to 0.01 mg KOH/g, which is consistent with the limits established for new transformer oils (maximal TAN = 0.03 mg KOH/g). In the adsorption studies, the best adsorption capacity values were as high as 0.1606 meq.g/g during conventional adsoprtion procedures using natural bauxite, and as high as 0.016 meq.g/g for the system diatomite/Tensiofix® 8426. Comparatively in this case, a negative effect could be observed on the adsorption phenomenon due to microemulsion impregnation on the surface of the diatomite

Conversão catalítica de clorometano em hidrocarbonetos

Amorphous silica-alumina and modified by incipient impregnation of iron, nickel, zinc and chromium were synthetized in oxide and metal state and evaluated as catalysts for the chloromethane conversion reaction. With known techniques their textural properties were determined and dynamics techniques in programmed temperature were used to find the acid properties of the materials. A thermodynamic model was used to determine the adsorption and desorption capacity of chloromethane. Two types of reactions were studied. Firstly the chloromethane was catalytically converted to hydrocarbons (T = 300 450 oC e m = 300 mg) in a fixed bed reactor with controlled pressure and flow. Secondly the deactivation of the unmodified support was studied (at 300 °C and m=250 g) in a micro-adsorver provided of gravimetric monitoring. The metal content (2,5%) and the chloromethane percent of the reagent mixture (10% chloromethane in nitrogen) were fixed for all the tests. From the results the chloromethane conversion and selectivity of the gaseous products (H2, CH4, C3 and C4) were determined as well as the energy of desorption (75,2 KJ/mol for Ni/Al2O3-SiO2 to 684 KJ/mol for the Zn/Al2O3-SiO2 catalyst) considering the desorption rate as a temperature function. The presence of a metal on the support showed to have an important significance in the chloromethane condensation. The oxide class catalyst presented a better performance toward the production of hydrocarbons. Especial mention to the ZnO/Al2O3-SiO2 that, in a gas phase basis, produced C3 83 % max. and C4 63% max., respectively, in the temperature of 450 oC and 20 hours on stream. Hydrogen was produced exclusively in the FeO/Al2O3-SiO2 catalysts (15 % max., T = 550 oC and 5,6 h on stream) and Ni/SiO2-Al2O3 (75 % max., T = 400 oC and 21,6 h on stream). All the catalysts produced methane (10 à 92 %), except for Ni/Al2O3-SiO2 and CrO/Al2O3-SiO2. In the deactivation study two models were proposed: The parallel model, where the product production competes with coke formation; and the sequential model, where the coke formation competes with the product desorption dessorption step. With the mass balance equations and the mechanism proposed six parameters were determined. Two kinetic parameters: the hydrocarbon formation constant, 8,46 10-4 min-1, the coke formation, 1,46 10-1 min-1; three thermodynamic constants (the global, 0,003, the chloromethane adsorption 0,417 bar-1, the hydrocarbon adsorption 2,266 bar-1), and the activity exponent of the coke formation (1,516). The model was reasonable well fitted and presented a satisfactory behavior in relation with the proposed mechanism

Obtenção de emulsões asfálticas modificadas utilizando resíduos industriais

The main objective of this research was the development and characterization of conventional and modified cationic asphalt emulsions. The asphalt emulsions were developed by using the Petroleum Asphalt Cement (CAP 50-70) from Fazenda Belém (Petrobras -Aracati-Ce). The first step in this research was the development of the oil phase (asphalt + solvent) and the aqueous phase (water + emulsifying agent + acid + additives), separately. During the experiments for the obtaining of the conventional asphalt emulsion, the concentration of each constituent was evaluated. For the obtaining of the oil phase, kerosene was used as solvent at 15 and 20 wt.%. For the development of the aqueous phase, the emulsifying agent was used at 0.3 and 3.0 wt.%, whereas the acid and the additive were set at 0.3 wt.%. The percentage of asphalt in the asphalt emulsion was varied in 50, 55, and 60 wt.% and the heating temperature was set at 120 °C. The aqueous phase in the asphalt emulsion was varied from 16.4 to 34.1 wt.% and the heating temperature was set at 60 °C. After the obtaining of the oil and the aqueous phases, they were added at a colloidal mill, remaining under constant stirring and heating during 15 minutes. Each asphalt emulsion was evaluated considering: sieve analysis, Saybolt Furol viscosity, pH determination, settlement and storage stability, residue by evaporation, and penetration of residue. After the characterization of conventional emulsions, it was chosen the one that presented all properties in accordance with Brazilian specifications (DNER-EM 369/97). This emulsion was used for the development of all modified asphalt emulsions. Three polymeric industrial residues were used as modifier agents: one from a clothing button industry (cutouts of clothing buttons) and two from a footwear industry (cutouts of sandals and tennis shoes soles), all industries located at Rio Grande do Norte State (Brazil).The polymeric residues were added into the asphalt emulsion (1 to 6 wt.%) and the same characterization rehearsals were accomplished. After characterization, it were developed the cold-mix asphalts. It was used the Marshall mix design. For cold-mix asphalt using the conventional emulsion, it was used 5, 6 and 7 wt.% asphalt emulsion. The conventional mixtures presented stability values according Brazilian specification (DNER-369/97). For mixtures containing asphalt modified emulsions, it was observed that the best results were obtained with emulsions modified by button residue

Novas alternativas de remoção de enxofre do óleo diesel utilizando tensoativos e microemulsões

The diesel combustion form sulfur oxides that can be discharged into the atmosphere as particulates and primary pollutants, SO2and SO3, causing great damage to the environment and to human health. These products can be transformed into acids in the combustion chamber, causing damage to the engines. The worldwide concern with a clean and healthy environment has led to more restrictive laws and regulations regulating the emission levels of pollutants in the air, establishing sulfur levels increasingly low on fuels. The conventional methods for sulfur removal from diesel are expensive and do not produce a zero-level sulfur fuel. This work aims to develop new methods of removing sulfur from commercial diesel using surfactants and microemulsion systems. Its main purpose is to create new technologies and add economic viability to the process. First, a preliminary study using as extracting agent a Winsor I microemulsion system with dodecyl ammonium chloride (DDACl) and nonyl phenol ethoxylated (RNX95) as surfactant was performed to choose the surfactant. The RNX95 was chosen to be used as surfactant in microemulsioned systems for adsorbent surface modification and as an extracting agent in liquid-liquid extraction. Vermiculite was evaluated as adsorbent. The microemulsion systems applied for vermiculite surface modification were composed by RNX95 (surfactant), n-butanol (cosurfactant), n-hexane (oil phase), and different aqueous phases, including: distilled water (aqueous phase),20ppm CaCl2solution, and 1500ppm CaCl2solution. Batch and column adsorption tests were carried out to estimate the ability of vermiculite to adsorb sulfur from diesel. It was used in the experiments a commercial diesel fuel with 1,233ppm initial sulfur concentration. The batch experiments were performed according to a factorial design (23). Two experimental sets were accomplished: the first one applying 1:2 vermiculite to diesel ratio and the second one using 1:5 vermiculite to diesel ratio. It was evaluated the effects of temperature (25°C and 60°C), concentration of CaCl2in the aqueous phase (20ppm and 1500ppm), and vermiculite granule size (65 and 100 mesh). The experimental response was the ability of vermiculite to adsorb sulfur. The best results for both 1:5 and 1:2 ratios were obtained using 60°C, 1500ppm CaCl2solution, and 65 mesh. The best adsorption capacities for 1:5 ratio and for 1:2 ratio were 4.24 mg sulfur/g adsorbent and 2.87 mg sulfur/g adsorbent, respectively. It was verified that the most significant factor was the concentration of the CaCl2 solution. Liquid-liquid extraction experiments were performed in two and six steps using the same surfactant to diesel ratio. It was obtained 46.8% sulfur removal in two-step experiment and 73.15% in six-step one. An alternative study, for comparison purposes, was made using bentonite and diatomite asadsorbents. The batch experiments were done using microemulsion systems with the same aqueous phases evaluated in vermiculite study and also 20ppm and 1500 ppm BaCl2 solutions. For bentonite, the best adsorption capacity was 7.53mg sulfur/g adsorbent with distilled water as aqueous phase of the microemulsion system and for diatomite the best result was 17.04 mg sulfur/g adsorbent using a 20ppm CaCl2solution. The accomplishment of this study allowed us to conclude that, among the alternatives tested, the adsorption process using adsorbents modified by microemulsion systems was considered the best process for sulfur removal from diesel fuel. The optimization and scale upof the process constitutes a viable alternative to achieve the needs of the market

Avaliação da eficiência de filtros anaeróbios na remoção de coliformes fecais e ovos de helmintos

The technology of anaerobic reactors for sanitary wastewater treatment has been extensively developed in Brazil, and today it is practically consolidated. They present several advantages, such as low construction and operating costs, and low sludge production, the anaerobic reactors are an attractive alternative to minimize problematic lack of basic sanitation in urban areas, and also of the rural areas. The anaerobic filters have been widely used in Brazil. It produces an effluent with low concentration of organic matter and solids suspended, besides conserving the nutrients, therefore, it is good for use in irrigation, but the practice must be associated with knowledge of the pathogens presence. The main objective of this study was to evaluate the efficiency of anaerobic filters in removal faecal coliforms and helminth eggs, and to verify if the effluent can be used for agricultural purposes, according to the World Organization of Health (WHO, 1989). The protocol used to enumerate helminths eggs was the modified Bailenger method, (Ayres and Mara, 1996) recommended by WHO for evaluation of raw effluent and treated effluent. The membrane filtration method was utilized to determine the concentrations of faecal coliforms. Three different systems of sewer treatment composed by anaerobic filters were analyzed. The results, in a general analysis, showed that all the researched systems reached a larger removal than 93% to helminth eggs, resulting in an effluent with smaller average than 1 egg/L. One of these systems, Sistema RN, reached a larger removal than 99%, confirming the good performance of the anaerobic filters in removal helminths eggs. Even with low concentrations of eggs in the influent, the filters were capable to remove this parameter efficiently. About faecal coliforms, it was observed for all the researched systems an effluent with 106 CFU/100mL. The high concentrations to faecal coliforms in the effluent just allow reuse for restricted irrigation, in agreement with the guidelines of WHO. Although the researched systems have not removed faecal coliforms efficiently, the results indicated a good efficiency of the anaerobic filters in removal helminth eggs

Variação da qualidade da água de chuva no início da precipitação

One of the most evident and actual concern, not only in the scientific means, but also of the public knowledge in general, is the lack problem of the potable water, that come increasing more each time, motivated mainly for the po llution of the sources, the bad use of the water and the increase of the population. In such a way, the necessity of looking for new water sources and the development of techniques to use sources minus explored is becoming even more important and urgent. T he rainwater comes being used since a long time like a supplying source, but, due the few knowledge of its characteristics, the generated preconception and the discrimination around its consumption and to the bad use of the technique of collection and stor age, it comes being little used, wasting consequently a significant parcel of this source. Trying to develop the knowing of some characteristics of the rainwater, the present work looks for to define the curve of variation of the quality of the rainwater i n three points with distinct characteristics of the city of Natal -RN, in the course of the precipitation, in some situations of time and space. For describe the curve of variation of the water s quality, some variables must be analyzed, and to be identifie d when they modify themselves in the endurance of rain, showing in which moment the purification of the water is more or less quickly. The pH, the Turbidity and the Electric Conductivity can be related with a big part of the physicist -chemistries variables found in the water and, like its analyses don't spend any material, they have easy access and measurement. The present work analyzes the curves of decline of these three variables, in three points with distinct characteristics in the city of Natal -RN, being these points: one next to the sea, another one in region with great buildings concentration and the last point in a less polluted area. For the studied region, it was during the five first millimeters of rain that occurs the biggest reduction of the exi sting impurities in the atmosphere, mainly between the first and the second millimeter, and after the five first millimeters the values of the variables stabilize. With exception of the University Campus, where initially the rainwater already has very good quality, the values of Turbidity and Electric Conductivity suffer a brusque reduction after the first millimeter of rain

O desenvolvimento da interlíngua na aprendizagem da escrita em inglês em uma escola bilíngue: um estudo exploratório

The aim of this study is to investigate the development of written Interlanguage in English as an Additional Language (AL) by students in the 2nd grade of Ensino Fundamental I in a bilingual school in the city of Natal-RN. For this purpose two research questions guided this study: (a) which hypotheses could be inferred from the writing development of the bilingual learners of English as AL? and, (b) what is the impact of the type of input monomodal or multimodal in the Interlanguage development in the AL of bilingual learners? The 38 learners were divided into a control group, with 21 learners exposed to monomodal input, and an experimental group, with 17 learners exposed to multimodal input, and pre and post-tests were applied to both groups. A mixed methods research design was conducted (DÖRNYEI, 2007) to involve both qualitative and quantitative data collection and analysis. The qualitative aspect comprehended descriptive characteristics that interpreted the central cognitive processes in the acquisition of writing in AL by the learners. Through these interpretations, it was possible to understand the constitution of written Interlanguage (SELINKER, 1972) according to the data generated by the learners. The quantitative data were presented as the results generated from the experimental design. Thus, they narrowed the relations between the dependent variable the writing development, that is, how close it is to the target form which was modified throughout the process by the independent variable the quality of input (VAN PATTEN, 2002, GASS, 1997, SCHMIDT, 1986, PARADIS, 2009; 2010, ELLIS, 1995), which, being monomodal or multimodal, its function was possibly to alter the route of acquisition. The quantitative results pointed towards significant gains by the experimental group, which had multimodality present, suggesting that the learners in this group seem to have been more able to cognitively register (SCHIMDT, 1990) aspects of learning than the learners in the control group

Permanência de Walflan de Queiroz: uma leitura da obra O Testamento de Jó

Este trabajo tiene como objeto de investigación literaria la obra: O testamento de Jo , lanzada en 1965, por Walflan de Queiroz. El poeta norte-río-grandense ilustra a través de un conjunto de poemas su experiencia religiosa y metafísica a partir de la desgracia sufrida por el personaje bíblico Jo, desarrollando una estética de la soledad, de la pobreza y de la marginalidad. Según Alter y Kermode (1997), la poesía de Jo es asombrosa en su fuerza e inventiva. Se pretende demostrar que las poesías de Walflan de Queiroz poseen dos corrientes definidas: si, por un parte, se vinculan al tema de Jo, mon doux Job , como él escribió en un poema; por otra, diseminan una postura amorosa. Con el objetivo de situar al autor y a su obra, se discuten el contexto histórico y la agitación cultural en Río Grande do Norte en la década de 1960. La lectura de O testamento de Jo nos llevó a realizar inicialmente una comparación de la poética walflaniana con textos bíblicos para la construcción de una atmósfera mística en el libro. Enseguida, el abordaje de los poemas amorosos que retratan la imagen femenina presente de forma platónica o bajo el velo de la mitología, de los mitos de Orfeu y Eurídice, retomados por el poeta. En Walflan de Queiroz, el amor no se concretiza. Y el bardo escribe como los románticos y los simbolistas

Modelos auto-similares para rádio fontes extragalácticas.

This work is a detailed study of self-similar models for the expansion of extragalactic radio sources. A review is made of the definitions of AGN, the unified model is discussed and the main characteristics of double radio sources are examined. Three classification schemes are outlined and the self-similar models found in the literature are studied in detail. A self-similar model is proposed that represents a generalization of the models found in the literature. In this model, the area of the head of the jet varies with the size of the jet with a power law with an exponent γ. The atmosphere has a variable density that may or may not be spherically symmetric and it is taken into account the time variation of the cinematic luminosity of the jet according to a power law with an exponent h. It is possible to show that models Type I, II and III are particular cases of the general model and one also discusses the evolution of the sources radio luminosity. One compares the evolutionary curves of the general model with the particular cases and with the observational data in a P-D diagram. The results show that the model allows a better agreement with the observations depending on the appropriate choice of the model parameters.

Parâmetros físico-químicos de estrelas nos campos de exoplanetas do satélite corot

A rotação estelar é um dos mais importantes observáveis da evolução estelar. Neste sentido, o satélite CoRoT representa uma oportunidade única de medir os períodos rotacionais para uma amostra de estrelas estatisticamente robusta, oferecendo dados absolutamente necessários para o estudo da rotação e seu papel na evolução estelar. Para conseguir isto, um passo fundamental é a caracterização física e química das estrelas observadas pelo CoRoT, especificamente devido ao fato de que o cálculo de períodos rotacionais confiáveis é um trabalho difícil sem a ajuda dos parâmetros estelares. Desta forma, foi elaborado um importante seguimento observacional das estrelas nos campos do CoRoT do anticentro LRa01 e do centro LRc01, permitindo a correta identificação dos períodos que reflitam a modulação rotacional. Nesta tese de doutorado são apresentados os resultados de tal seguimento. Parâmetros físicos e químicos, tais como temperatura efetiva Teff , gravidade superficial log(g), velocidade de microturbulência Vmic, abundância de ferro [Fe/H], velocidade de rotação projetada Vsin(i), e abundância de lítio A(Li) são apresentados para uma amostra de 116 estrelas dos campos CoRoT. Elas se encontram em diferentes estágios evolutivos, desde a sequência principal (SP) até o ramo das gigantes vermelhas (GV). As observações foram feitas utilizando os espectrógrafos UVES (VLT) e HYDRA (CTIO). Para a derivação de tais parâmetros foram utilizados o programa TurboSpectrum e os modelos de atmosfera de MARCS. Paralelamente, velocidades rotacionais Vsin(i) foram obtidas a partir do ajuste dos perfis observados e sintéticos das linhas de ferro e por meio de uma calibração de função de correlação cruzada (CCF). Períodos rotacionais Prot para 77 estrelas da amostra foram obtidos a partir das curvas de luz do satélite CoRoT. Extensas tabelas destes parâmetros e seus respectivos erros são apresentadas. Foram encontradas diferenças nas distribuições de Teff , [Fe/H] e estágios evolutivos entre os diferentes campos do CoRoT, indicando possíveis efeitos de seleção na amostra, assim como a existência de diferentes populações estelares do disco Galáctico. Por outro lado, o comportamento rotacional e as abundâncias de lítio não apresentam diferenças entre estrelas de parâmetros físicos similares, mas que pertencem a diferentes campos do CoRoT. A partir da análise de temperaturas, foi encontrada uma maior extinção por avermelhamento para estrelas do CoRoT localizadas no campo LRc01, assim como um gradiente deste valor em função da distância. Os resultados mostram que as abundâncias de lítio, as velocidades de rotação e os períodos rotacionais apresentam o mesmo comportamento descrito na literatura. Por outro lado, é apresentada pela primeira vez a relação que existe entre o lítio e o período de rotação em diferentes estágios evolutivos, mostrando, tal como era esperado, que ambas as grandezas possuem uma anticorrelação. Também é apresentada a evolução simultânea da rotação e do lítio, e foram calculadas relações que permitem obter valores médios de A(Li) como função da temperatura efetiva e do período rotacional. Os dados apresentados nesta tese de doutorado representam um importante ponto de partida para serem utilizados como uma amostra de calibração para diferentes programas no contexto da missão do satélite CoRoT, uma vez que a lista de estrelas aqui analisadas são parte das mais brilhantes que compõem o campo Exo do CoRoT

Representações espectrais de sistemas complexos: aplicações à síntese de superfícies brownianas fracionárias anisotrópicas, filtragem de sinais e identificação de correlações

In this thesis, we study the application of spectral representations to the solution of problems in seismic exploration, the synthesis of fractal surfaces and the identification of correlations between one-dimensional signals. We apply a new approach, called Wavelet Coherency, to the study of stratigraphic correlation in well log signals, as an attempt to identify layers from the same geological formation, showing that the representation in wavelet space, with introduction of scale domain, can facilitate the process of comparing patterns in geophysical signals. We have introduced a new model for the generation of anisotropic fractional brownian surfaces based on curvelet transform, a new multiscale tool which can be seen as a generalization of the wavelet transform to include the direction component in multidimensional spaces. We have tested our model with a modified version of the Directional Average Method (DAM) to evaluate the anisotropy of fractional brownian surfaces. We also used the directional behavior of the curvelets to attack an important problem in seismic exploration: the atenuation of the ground roll, present in seismograms as a result of surface Rayleigh waves. The techniques employed are effective, leading to sparse representation of the signals, and, consequently, to good resolutions

Um estudo sobre a interação estrela-planeta a partir da relação massa-período planetário com a atividade estelar

n this work, we analyze the behavior of the chromospheric and coronal activities as a function of the mass and the orbital period of extrasolar planets which were detected by transit technique. So we look for possible effects of the planet on the star s chromosphere and corona. For this study we selected a sample of 48 stars with chromospheric activity indicator and 23 with coronal activity indicator. Our work is based on the work from Pont et al. (2011) in order to study stars with planets which were obtained by transit technique. Furthermore, we studied the relationship between planetary mass and orbital period with the chromospheric and coronal activity in order to better understand which influences the planets cause in the outer layers of stellar atmosphere. In our analysis we can observe that the mass of the planets exerts no influence in the stellar activity. However, we observed that the stellar coronal and chromospheric activities decrease with the increase of the orbital period of the planet

Um estudo sobre a interação estrela-planeta a partirda relação massa-período planetário com a atividade estelar

In this work, we analyze the behavior of the chromospheric and coronal activities as a function of the mass and the orbital period of extrasolar planets which were detected by transit technique. So we look for possible effects of the planet on the star s chromosphere and corona. For this study we selected a sample of 48 stars with chromospheric activity indicator and 23 with coronal activity indicator. Our work is based on the work from Pont et al. (2011) in order to study stars with planets which were obtained by transit technique. Furthermore, we studied the relationship between planetary mass and orbital period with the chromospheric and coronal activity in order to better understand which influences the planets cause in the outer layers of stellar atmosphere. In our analysis we can observe that the mass of the planets exerts no influence in the stellar activity. However, we observed that the stellar coronal and chromospheric activities decrease with the increase of the orbital period of the planet