Equilíbrio líquido-líquido para o sistema biodiesel de óleo de semente de melão (Cucumis melo l.) + metanol + glicerina

Rio Grande do Norte, northeast state from Brazil, it is the greatest producer and exporter of yellow melon, well known as Spanish melon. Despite the consumption of this fruit to be mainly its pulp, melon seeds are an important source of lipids considered an industrial residue it has been discharge product. The use of oilseeds in order to produce biodiesel establishes an important raw material and the increase of its production promotes the national development of the agriculture. In this background, the aim of this work has been to use oil from seeds of yellow melon to produce biodiesel and to accomplish a study of the phase equilibrium of the system evolving biodiesel, methanol and glycerin. The biodiesel was obtained by oil transesterification through methylic route with molar ratio 1:9.7 (oil:alcohol) and with a mass of NaOH of 0.5% from the oil mass; the reaction time was 73 minutes at 55 °C. A yield of 84.94% in biodiesel was achieved. The equilibria data present a well-characterized behavior with a great region of two phases. The tie lines indicate that methanol has a best solubility in the phase that is rich in glycerin. Consistency of the experimental data was made based on Othmer-Tobias and Hand correlations which values above 0.99 were found to correlation coefficients, this fact confers a good thermodynamic consistency to the experimental data. NRTL and UNIQUAC models were employed to predict liquid-liquid equilibrium of this system. It was observed a better concordance of the results when NRTL was applied (standard deviation 1.25%) although the UNIQUAC model has presented a quite satisfactory result either (standard deviation 2.70%). The NRTL and UNIQUAC models were also used to evaluate the effect of temperature in the range of 328 K to 358 K, in which a little change in solubility with respect to the data obtained at 298 K was observed, thus being considered negligible the effect of temperature

Avaliação de catalisadores a base de carbeto e nitreto de molibdênio na obtenção de lactitol via hidrogenação da lactose

Seeking a greater appreciation of cheese whey was developed to process the hydrogenation of lactose for the production of lactitol, a polyol with high added value, using the catalyst Ni / activated carbon (15% and 20% nickel), the nitride Mo2N, the bimetallic carbide Ni-Mo/ activated carbon and carbide Mo2C. After synthesis, the prepared catalysts were analyzed by MEV, XRD, laser granulometry and B.E.T. The reactor used in catalytic hydrogenation of lactose was the type of bed mud with a pressure (68 atm), temperature (120 oC) and stirring speed (500 rpm) remained constant during the experiments. The system operated in batch mode for the solid and liquid and semi-continuous to gas. Besides the nature of the catalyst, we studied the influence of pH of reaction medium for Mo2C carbide as well as evaluating the character of the protein inhibitor and chloride ions on the activity of catalysts Ni (20%)/Activated Carbon and bimetallic carbide Ni-Mo/Activated Carbon. The decrease in protein levels was performed by coagulation with chitosan and adsorption of chloride ions was performed by ion exchange resins. In the process of protein adsorption and chloride ions, the maximum percentage extracted was about 74% and 79% respectively. The micrographs of the powders of Mo2C and Mo2N presented in the form of homogeneous clusters, whereas for the catalysts supported on activated carbon, microporous structure proved impregnated with small particles indicating the presence of metal. The results showed high conversion of lactose to lactitol 90% for the catalyst Ni (20%)/Activated Carbon at pH 6 and 46% for the carbide Mo2C pH 8 (after addition of NH4OH) using the commercial lactose. Monitoring the evolution of the constituents present in the reaction medium was made by liquid chromatography. A kinetic model of heterogeneous Langmuir Hinshelwood type was developed which showed that the estimated constants based catalysts promoted carbide and nitride with a certain speed the adsorption, desorption and production of lactitol

Comparação entre planejamento estatístico experimental e análise dimensional em operações de mistura e separação para sistema óleo-água

This work aims to determine a better methodology to help predicting some operational parameters to a new design of mixer-settler on treating wastewater produced by petroleum industry, called MDIF (Misturador-Decantador à Inversão de Fases/ Mixer-Settler based on Phase Inversion MSPI). The data from this research were obtained from the wastewater treatment unit, called MSPI-TU, installed on a wastewater treatment plant (WTP) of PETROBRAS/UO-RNCE. The importance in determining the better methodology to predict the results of separation and extraction efficiency of the equipment, contributes significantly to determine the optimum operating variables for the control of the unit. The study was based on a comparison among the experimental efficiency (E) obtained by operating MSPI-TU, the efficiency obtained by experimental design equation (Eplan) from the software Statistica Experimental Design® (version 7.0), and the other obtained from a modeling equation based on a dimensional analysis (Ecalc). The results shows that the experimental design equation gives a good prediction of the unit efficiencies with better data reliability, regarding to the condition before a run operation. The average deviation between the proposed by statistic planning model equation and experimental data was 0.13%. On the other hand, the efficiency calculated by the equation which represents the dimensional analysis, may result on important relative deviations (up 70%). Thus, the experimental design is confirmed as a reliable tool, with regard the experimental data processing of the MSPI-TU

Análise da salubridade do meio urbano com base na utilização de índices ambientais: aplicação na bacia de drenagem XII da cidade do Natal-RN

The growing accumulation of people in urban centers caused chronic problems of the cities to begin to take an increasingly unsustainable. Primarily related to lack of infrastructure coupled with sanitation and lack of investment in critical sectors such as health, education, housing and transportation, these problems start to deteriorate markedly the quality of life of city dwellers and put into test management policies of the spaces urbanized. To reverse this situation, shows is essential to the use of tools (highlighting this harvest rates and environmental indicators) that help in assessing the current conditions and may assist in predicting future scenarios. From the information listed above, now put the research seeks to present an index called ISBA Environmental (Sanitation Index) which looks at the four urban systems (water, sewer, solid waste and urban drainage) from the viewpoint of application in a geographical cutout specific - in this case the Drainage Basin XII, defined by the Plan of Urban Drainage Stormwater in the city of Natal, capital of Rio Grande do Norte. This index, together with analysis of other factors sought to trace the current conditions of the basin and thus, assist in proposing the best solutions. For the preparation of the index was applied a questionnaire with a sample of 384 (three hundred eighty-four) households that aimed to study two variables: access to services and satisfaction of the population in relation to these. The ISBA has shown that the system is the most deficient collection and disposal of effluents (ICE = 47.66%), followed by the drainage of rainwater (IDAP = 54.17%), water supply (AAI = 61, 36) and solid waste collection (IRS = 78.28). With the ISBA was possible to verify that the qualitative data shows whose subjectivity is evident (as is the case of user satisfaction) can be of great importance when an assessment, since we obtained the correlation coefficient between the variables "Access" and " Satisfaction "equal to 0.8234, showing a strong correlation between the existence / quality of service offered and the impressions of the population that receives them

Simulação do sistema de esgotamento sanitário de Ponta Negra- Natal: mitigação dos riscos ambientais e estratégia de manutenção preditiva

The simulation of SES-Natal Ponta Negra: mitigation of environmental risks and predictive maintenance strategy was developed in the context of several operational irregularities in the pumping stations and sewage systems in the system Ponta Negra. Thus, the environmental risks and complaints against the company due to overflows of sewage into the public thoroughfare became common. This neighborhood has shown in recent years an increase of resident higher than the initial expectation of growth. In this sense presumed the large population growth and generation of sewers higher than expected, associated to the use of corrective maintenance and misuse of the system may be the main causes of operational failures occurring in the SES. This study aimed at analyzing the hydraulic behavior of SES Ponta Negrathrough numerical simulation of its operation associated to future scenarios of occupation. The SES Ponta Negra has a long lengthof collection networks and 6 pumping stations interconnected, being EE 1, 2, 4 coastal way, and beach Shopping interconnected EE3 to receives all sewers pumped from the rest pumping station and pumped to the sewage treatment station of neighborhood which consists of a facultative pond followed by three maturation ponds with disposal of treated effluent into infiltration ditches. Oncethey are connected with each other, the study was conducted considering the days and times of higher inflow for all lifts. Furthermore, with the aim of measuring the gatherer network failures were conducted data survey of on the networks. Thephysical and operational survey data was conducted between January/2011 and janeiro/2012. The simulation of the SES was developed with the aim ofdemonstrating its functioning, eithercurrently and in the coming years, based in population estimates and sewage flow. The collected data represents the current framework of the pumping stations of the SES Ponta Negra and served as input to the model developed in MS Excel ® spreadsheet which allowed simulating the behavior of SES in future scenarios. The results of this study show thatBeach Shopping Pumping Station is actually undersized and presents serious functioning problemsthatmay compromise the environmental quality of surrounding area. The other pumping stations of the system will reach itsmaximum capacity between 2013 and 2015, although the EE1 and EE3 demonstrateoperation capacity, even precariously, until 2017. Moreover, it was observed that the misuse of the network system, due to the input of both garbage and stormwater, are major factors of failures that occur in the SES. Finally, it was found that the corrective maintenance appliance, rather than predictive,has proven to beinefficient because of the serious failuresin the system, causing damage to the environment and health risks to users

Aprendendo e ensinando o sistema de numeração decimal: uma contribuição à prática pedagógica do professor

The central question of the present study is to identify the epistemological knowledge that the teachers-trainees possess regarding the characteristics (properties) of the decimal numbering system; its purpose is to offer a contribution to the pedagogic practice of the teachers who work within the Basic Literacy Cycle, in terms of what concerns both the acquisition of contents and the development of the knowledge that helps them in the elaboration of adequate strategies to working with the Decimal Numbering System in the classroom. The study is based on the constructivist sociointeractionist approach to teaching Mathematics and it constitutes, in itself, a methodological intervention with the teachers-trainees engaged in the Professional Qualification Program in Basic Education of the Federal University of Rio Grande do Norte. The foundations of the study were found in investigations of researchers who had carried out studies on the construction of numerical writing, showing, for instance, that the construction process of ideas and procedures involved in groupings and changes to base 10 take a lot longer to be accomplished than one can imagine. A set of activities was then elaborated which could not only contribute to the acquisition of contents but that could also make the teachers-trainees reflect upon their teaching practices in the classroom so that in this way they will be able to elaborate more consistent didactic approaches, taking into consideration the previous knowledge of the students and also some obstacles that often appear along the way. Even when teachers have access to the most appropriate dicactic resources, the lack of knowledge of the content and of the real meaning of that content make the Decimal Numbering System, a subject of fundamental importance, be taught most times in a mechanical way. The analisys of the discussions and behaviours of the teachers-trainees during the activities reavealed that they made them reflect upon their current practices in the classroom and that, as a whole, the aims of each of the activities carried out with the teachers-trainers were reached

Avaliação da usabilidade de um sistema informatizado de controle acadêmico: um estudo com coordenadores e secretários de cursos stricto sensu da UFRN

The aim of this study is to assess the usability of the Integrated Management System for Academic Activities (SIGAA) for the sensu stricto postgraduate programs at Universidade Federal do Rio Grande do Norte. The study was based on ergonomic criteria proposed by Bastien and Scapin (1993) and the Federal Government s Handbook of Usability (2010). The methodology used was a descriptive data survey involving an online questionnaire, and a sample of 46 system users, composed of coordinators and secretaries from the sensu stricto postgraduate programs. In addition to this procedure, open interviews were held with the users as well as a documental analysis of calls registered by them at the SIGAA between May 2012 and June 2013. Data analysis showed that a number of additional usability criteria need to be implemented, primarily related to ergonomic problems of orientation, error management and workload. Based on the analyses, several changes were proposed that may streamline secretarial activities, as well as provide greater satisfaction and interaction between the SIGAA and its users

Síntese, sinterização e caracterização de ferritas à base de Ni-Zn

Were synthesized different ferrites NixZn1-xFe2O4 (0,4 ≤ x ≤ 0,6) compositions by using citrate precursor method. Initially, the precursors citrates of iron, nickel and zinc were mixed and homogenized. The stoichiometric compositions were calcined at 350°C without atmosphere control and the calcined powders were pressed in pellets and toroids. The pressed material was sintered from 1100º up to 1200ºC in argon atmosphere. The calcined powders were characterized by XRD, TGA/DTG, FTIR, SEM and vibrating sample magnetometer (VSM). All sintered samples were characterized using XRD, SEM, VSM and measurements of magnetic permeability and loss factor were obtained. It was formed pure ferromagnetic phase at all used temperatures. The Rietveld analyses allowed to calculate the cations level occupation and the crystallite size. The analyses obtained nanometric crystals (12-20 nm) to the calcined powder. By SEM, the sintered samples shows grains sizes from 1 to 10 μm. Sintered densities (ρ) were measured by the Archimedes method and with increasing Zn content, the bulk density decrease. The better magnetization results (105-110 emu/g) were obtained for x=0,6 at all sintering temperatures. The hysteresis shows characteristics of soft magnetic material. Two magnetization processes were considered, superparamagnetism at low temperature and the magnetic domains formation at high temperatures. The sintered toroids presents relative magnetic permeability (μr) from 7 to 32 and loss factor (tanδ) of about 1. The frequency response of toroids range from 0,3 kHz to 0,2 GHz. The composition x=0,5 presents both greater μr and tanδ values and x=0,6 the most broad range of frequency response. Various microstructural factors show influence on the behavior of μr and tanδ, such as: grain size, porosity across grain boundary and inside the grain, grain boundary content and domain walls movement during the process of magnetization at high frequency studies (0,3kKz 0,2 GHz)

Desenvolvimento de componentes nanométricos para aplicação em células a combustível à base de sólidos estruturados e filmes finos

The present work aims the preparation of filmes of strontium-doped lanthanum manganite (perovskita) yttria-stabilized zirconia (LSM-SDC) films deposited on substrate of YSZ by means of spin coating technique having as principal objective their application to solid oxide fuel cells of intermediate temperature. La0,8Sr0,2MnO3 and Ce0,8Sm0,2O1,9 were obtained by modified Pechini method by use of gelatin which act as polymerization agent. The powders obtained were characterized by Xray fluorescence, X ray diffraction, electronic scanning microscopy and the superficial area by BET method. The results obtained by X-ray fluorescence showed that the route adopted for obtention of powders was effective in the obtention of the compositions with close values to the stoichiometrics. Ethyl cellulose was used as pore-forming agent and mixed with the LSM-SDC powders in weight proportions of 1:24, 2:23 and 1:9. The films were sintered at 1150 °C for 4 h and characterized by X-ray diffraction and scanning electron microscopy technique (SEM) and atomic force. The phases quantification of the precursory powders and of the obtained films was carried through Rietveld method. According with the analysis of SEM, as the content of ethyl cellulose was increased, the pore distribution in films become more uniform and the pore size reduced. The methodology used for the obtention of the films was very efficient, considering a material was obtained with characteristics that were proper to the application as electrolyte/cathode system to solid oxide fuel cells

As Mulheres e as Muralhas do Patriarcado e do Capitalismo: Terceirização e Precarização do Trabalho no Sistema do Capital

Our dissertation deals with the material living conditions of women workers and the relations of the wage who undergo in the hospital scope, taking as the locus of empirical research the Hospital Dr. João Machado, located in Natal / RN. Its purpose is to analyze the main implications of precarious work contracts in the economic and social dimensions from life of workers, explaining the main conditionings. The majority presence of women in wage relations not only in the hospital service, as well as in the service sector in general has motivated us to appreciation of the form of participation of women in health services and, in particular, at the hospital space. From the critical dialectical method, through processes of successive approximations to the reality, we analyze the patriarchal system of social relations and their repercussions for the Social and Sexual Division of Labor in the context of contemporary capitalist society, explaining the determinants of inequality, founded in social relations of sex, to the predominance of women in the hospital service and unveiling these participation trends in the labor market. The analyzes are based on bibliographic research - theoretical and methodological basis of research - combined with reflections that emerged from the field. The systematized and analyzed information reveal the uniqueness of the current social and economic situation of workers women with ties outsourced, paradoxically expresses on the expansion of the insertion in universe of labor, in overexploitation, in the precariousness of work and living conditions and persistent inequality in and in the social relations and in relations between the sexes

BSmart: desenvolvimento rigoroso de aplicações Java Card com base no método formal B

Java Card technology allows the development and execution of small applications embedded in smart cards. A Java Card application is composed of an external card client and of an application in the card that implements the services available to the client by means of an Application Programming Interface (API). Usually, these applications manipulate and store important information, such as cash and confidential data of their owners. Thus, it is necessary to adopt rigor on developing a smart card application to improve its quality and trustworthiness. The use of formal methods on the development of these applications is a way to reach these quality requirements. The B method is one of the many formal methods for system specification. The development in B starts with the functional specification of the system, continues with the application of some optional refinements to the specification and, from the last level of refinement, it is possible to generate code for some programming language. The B formalism has a good tool support and its application to Java Card is adequate since the specification and development of APIs is one of the major applications of B. The BSmart method proposed here aims to promote the rigorous development of Java Card applications up to the generation of its code, based on the refinement of its formal specification described in the B notation. This development is supported by the BSmart tool, that is composed of some programs that automate each stage of the method; and by a library of B modules and Java Card classes that model primitive types, essential Java Card API classes and reusable data structures

Aplicação de ontologias para métodos de negociação de um sistema multiagente para o reconhecimento de padrões

The use of intelligent agents in multi-classifier systems appeared in order to making the centralized decision process of a multi-classifier system into a distributed, flexible and incremental one. Based on this, the NeurAge (Neural Agents) system (Abreu et al 2004) was proposed. This system has a superior performance to some combination-centered methods (Abreu, Canuto, and Santana 2005). The negotiation is important to the multiagent system performance, but most of negotiations are defined informaly. A way to formalize the negotiation process is using an ontology. In the context of classification tasks, the ontology provides an approach to formalize the concepts and rules that manage the relations between these concepts. This work aims at using ontologies to make a formal description of the negotiation methods of a multi-agent system for classification tasks, more specifically the NeurAge system. Through ontologies, we intend to make the NeurAge system more formal and open, allowing that new agents can be part of such system during the negotiation. In this sense, the NeurAge System will be studied on the basis of its functioning and reaching, mainly, the negotiation methods used by the same ones. After that, some negotiation ontologies found in literature will be studied, and then those that were chosen for this work will be adapted to the negotiation methods used in the NeurAge.

Sistema especialista fuzzy para dimensionamento de bombeio mecânico

Despite the emergence of other forms of artificial lift, sucker rod pumping systems remains hegemonic because of its flexibility of operation and lower investment cost compared to other lifting techniques developed. A successful rod pumping sizing necessarily passes through the supply of estimated flow and the controlled wear of pumping equipment used in the mounted configuration. However, the mediation of these elements is particularly challenging, especially for most designers dealing with this work, which still lack the experience needed to get good projects pumping in time. Even with the existence of various computer applications on the market in order to facilitate this task, they must face a grueling process of trial and error until you get the most appropriate combination of equipment for installation in the well. This thesis proposes the creation of an expert system in the design of sucker rod pumping systems. Its mission is to guide a petroleum engineer in the task of selecting a range of equipment appropriate to the context provided by the characteristics of the oil that will be raised to the surface. Features such as the level of gas separation, presence of corrosive elements, possibility of production of sand and waxing are taken into account in selecting the pumping unit, sucker-rod strings and subsurface pump and their operation mode. It is able to approximate the inferente process in the way of human reasoning, which leads to results closer to those obtained by a specialist. For this, their production rules were based on the theory of fuzzy sets, able to model vague concepts typically present in human reasoning. The calculations of operating parameters of the pumping system are made by the API RP 11L method. Based on information input, the system is able to return to the user a set of pumping configurations that meet a given design flow, but without subjecting the selected equipment to an effort beyond that which can bear

Desenvolvimento de sistema magnético polimérico contendo antimicrobianos para tratamento de infecções por Helicobacter pylori

Helicobacter pylori is the main cause of gastritis, gastroduodenal ulcer disease and gastric cancer. The most recommended treatment for eradication of this bacteria often leads to side effects and patient poor compliance, which induce treatment failure. Magnetic drug targeting is a very efficient method that overcomes these drawbacks through association of the drug with a magnetic compound. Such approach may allow such systems to be placed slowed down to a specific target area by an external magnetic field. This work reports a study of the synthesis and characterization of polymeric magnetic particles loaded with the currently used antimicrobial agents for the treatment of Helicobacter pylori infections, aiming the production of magnetic drug delivery system by oral route. Optical microscopy, scanning electron microscopy, transmission electron microscopy, x-ray powder diffraction, nitrogen adsorption/desorption isotherms and vibrating sample magnetometry revealed that the magnetite particles, produced by the co-precipitation method, consisted of a large number of aggregated nanometer-size crystallites (about 6 nm), creating superparamagnetic micrometer with high magnetic susceptibility particles with an average diameter of 6.8 ± 0.2 μm. Also, the polymeric magnetic particles produced by spray drying had a core-shell structure based on magnetite microparticles, amoxicillin and clarithromycin and coated with Eudragit® S100. The system presented an average diameter of 14.2 ± 0.2 μm. The amount of magnetite present in the system may be tailored by suitably controlling the suspension used to feed the spray dryer. In the present work it was 2.9% (w/w). The magnetic system produced may prove to be very promising for eradication of Helicobacter pylori infections

Monitoramento ambiental da costa do Rio Grande do Norte com base em sensoriamento remoto e geodésia de precisão

This paper presents models of parameters of Sea Surface Layer (SSL), such as chlorophyll-a, sea surface temperature (SST), Primary Productivity (PP) and Total Suspended Matter (TSM) for the region adjacent to the continental shelf of Rio Grande do Norte (RN), Brazil. Concentrations of these parameters measured in situ were compared in time quasi-synchronous with images AQUA-MODIS between the years 2003 to 2011. Determination coefficients between samples in situ and bands reflectance sensor AQUA-MODIS were representative. From that, concentrations of SSL parameters were acquired for the continental shelf of the RN (eastern and northern) analyzing the geographic distribution of variation of these parameters between the years 2009-2012. Geographical and seasonal variations mainly influenced by global climate phenomena such as El Niño and La Niña, were found through the analysis of AQUA-MODIS images by Principal Components Analysis (PCA). Images show qualitatively the variance and availability of TSM in the regions, as well as their relationship with coastal erosion hotspots, monitored along the coast of the RN. In one of the areas identified as being of limited availability of TSM, we developed a methodology for assessment and evaluation of Digital Elevation Models (DEM) of beach surfaces (emerged and submerged sections) from the integration of topographic and bathymetric data measured in situ and accurately georeferenced compatible to studies of geomorphology and coastal dynamics of short duration. The methodology consisted of surveys with GNSS positioning operated in cinematic relative mode involved in topographic and bathymetric executed in relation to the stations of the geodetic network of the study area, which provided geodetic link to the Brazilian Geodetic System (GBS), univocal , fixed, and relatively stable over time. In this study Ponta Negra Beach, Natal / RN, was identified as a region with low variance and availability of MPS in the region off, as characterized by intense human occupation and intense coastal erosion in recent decades, which presents potential of the proposed methodology for accuracy and productivity, and the progress achieved in relation to the classical methods of surveying beach profiles