Impacto da atividade física na qualidade de vida em mulheres de meia idade: estudo de base populacional

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Diferenças de gênero na produção de associações livres de palavras através do ciclo sono-vigília

Although several studies, have shown differences in cognitive performance between men and women, it not yet known whether these differences occur in tasks involving free association of words (WA). Studies across the sleep-wake cycle (SWC) suggest that rapid eye movement sleep (REM) favors semantic flexibility, in comparison with pre-sleep waking (Pre-WK), slow-wave sleep (SWS) and post-sleep waking (Post-WK). The present work has two aims: (1) to evaluate the semantic distances of word pairs produced by AP, comparing men and women, (2) to evaluate semantic distance in word pairs produced by free association across the SWC in young adults of both sexes. To achieve aim (1), we applied a task of WA in 68 adult volunteers during waking (52 women and 16 men). The WA task consisted of writing the first word that came to mind after viewing another word offered as a stimulus (root Word). To achieve aim (2), we performed polysomnography to identify specific stages of the SWC. The experimental subjects were then awakened (if they were asleep) and were immediately given a WA task. The task was administered to 2 groups of 10 subjects each (G1 and G2). G1 subjects were stimulated with the same set of root words after waking from various states of SWC, while G2 subjects received sets of different root words at each state of the SWC. In the absence of a Portuguese corpus suitable for the measurement of semantic distances, the words collected in our experiments were translated to English, and semantically quantified within a systematic and representative corpus of that language (Wordnet). This procedure removed the polysemies typical of Portuguese, but preserved the semantic macrostructure common to both languages. During waking, we found that semantic distances are significantly lower in WA produced by women, in comparison with the distances observed in men. Through the SWC, there were no statistically significant differences in G1. In G2 women, we detected a significant increase of semantic distances upon being awakened from SWS. In contrast, G2 men showed a significant increase in semantic distances upon being awakened from REM. The results of the first experiment are consistent with the notion that women have a more concrete reasoning than men. The results of the second experiment indicate that men awakened from REM present more flexibility in word association than when being awakened from other states. In contrast, women showed more flexible word association after being awakened from SWS, in compared with other states. The results indicate that the cognitive flexibility attributed to different states of the SWC shows gender dependency

O Trabalho e o labirinto da responsabilidade socioempresarial:a experiência da cidadania empresarial do Banco do Brasil

In the current systemic crisis, economic policy is directed to correct the consequences of the functioning of this metabolism, but within the limits of the capital. From this perspective, decision makers propose trade policies, agricultural and industrial to ensure conditions for economic growth. However, as a dead end, there is failure of the State in giving efficacy to the operation of all segments of the economy, especially given the budget constraint. Public managers are forced to seek external resources, resuming the cycle of political allegiance to the interests of international financial and banking representatives, installed in so-called multilateral. The complex ideological capital comes into play in trying to convince society that the paths taken by governments are inevitable, and that capitalism can be "humanized", even with the realization of the growing inequalities caused by historical irrationalism of the production process of capital . In this sense, emerging concepts that attempt to demonstrate the compatibility of the system to real human needs. This ideological offensive is intended to legitimize the capital. The so-called third sector has a special highlight with the concept of corporate social responsibility. It creates a political environment in which the inevitable mix-up with new illusions offered by and often funding the metabolism of capital in order to perpetuate this system. In this context, political elites, and considerable portions of the academy, embark on "waves of capitalist optimism," while the sociometabolismo capital expands its historical limits, driving forces postponing their collapse, but that cause human suffering and ecological stress. Wars are disseminated to strengthen the deadly war industry and the automobile industry; and devastating the environment of which depends the capital system. In this scenario disassemble, propositions emerge around a "new social pact" in order to minimize the adverse effects of the dynamics of reproduction of capital. The business class is called to exercise its role through the discourse that appeals to social responsibility programs, in order to intervene directly in the "social question". The core of this research is precisely this point. Although there is considerable scholarship on the phenomenon of Social Responsibility and Corporate Citizenship, there is also an evident lack of this approach focused on the banking sector in Brazil. The importance of rentier capital increased ownership of shares in the wealth produced by all of Brazilian society, justifies a sociological research project on Social Responsibility in the domestic financial sector. In this sense, it was decided to perform a dynamic approach to the "Corporate Citizenship" in the banking industry, specifically in the Bank of Brazil. As this is a key institution, is important analyze of the impacts of this strategy fetish of capitalist reproduction, in order to evaluate the social legitimization of rentier capital in Brazil. In this scenario of the abundance of the discourse on social responsibility there exist a progressive impoverishment of professional work in this segment in Brazil. There is a dramatic mismatch between rhetoric and practice because of the trend of deepening vulnerability of the working conditions of the Brazilian bank worker, from the 1990's. In the specific case of the Bank of Brazil, the first initiative of the institution was to conform to the principles of the UNO and the Ethos Institute, aiming to align their domestic policies to this new strategy of domination of capital. The purpose is to place the Bank in the ideological sphere of corporate social responsibility, just as with its partners in the private financial intercapitalist competition. Indeed, in the internal ambit of the Bank of Brazil, there is a policy to adjust its functional segments to the doctrine of Social Corporate Responsibility. The concepts of this doctrine is presented as something inexorable. There are no alternatives. The Bank of Brazil operates in a highly competitive market, the segment featuring the dominance of financial capital accumulation today. For this reason it can not fail to incorporate the technological advances organizational. For employees there is no alternative but to adapt to this new set of ideas proposed by the metabolism of capital

Alguns aspectos sobre o processo da democratização dos sistemas políticos no mundo árabe :Egito e Líbano como modelos de estudo

The World has tried diverse democratic waves at distinct moments. Some nations have adopted the idea of the democracy for years; others have not yet and other ones are still in a slow process of transition. The field of studies on the Arabian political systems has testified since the last quarter of 20th century a notorious development. This advance disclosed in the existence of a set of trends that has turned around a number of concepts and main theoretical frames such as the political pluralism and the democratic transition and the civil society and its relation with the State. The speech on the process of democratic transition consists in part in the capture and the analysis of the role of the forces and the organizations of the civil society in this process. The peculiarities of the Arab World excite questions concerning the establishment of one governmental system in this universe in the mold of that one that develops with hegemony in the Occident, which has become an interesting field of inquiries for the Political Science. This study comprises the analysis of some aspects of the political situation in the Arab World towards the process of democratization in which Egypt and Lebanon are models of study. Thus the theoretical basis of the term democracy is introduced, presenting different considerations about this expression, since the sprouting of the term until its current conception; later the civil society is analyzed as well as the systems of the political parties and the electoral systems of both countries in attempt to identify the level of democratization existing there and also to find the possible ways to magnify the democratic horizons

Ideais formativos de homem da emissora de Educação Rural de Caicó (Rio Grande do Norte, 1963-1978)

Under the aegis of the third diocese bishop of Caicó, Dom Manuel Tavares de Araújo, the Broadcasting Station of Rural Education of that city was founded, in May 1 s" 1963 with the ideal of being then an educational city, preferentially for youths and adults, rural meu and women of the arca of Seridó in Rio Grande do Norte state. In the year of its 40th birthday (2003), we began the investigation of that radio station choosing as study object its educational and formative programming, in the inc1usion of the first fifteen years of its existence (1963-1978), period that reaches the official inauguration of the Radio Station and the end of the bishopric of its fOllllder as Bishop of Caicó. Elucidating and showing Man's formative ideaIs longed by that Catholic educational broadcasting station, underlying to its radiophonic programming, such as the idealization for it reached, is the objective of this Doctorate work. It was considered pertinent to discover the guidelines that historically have permeated the Social Doçtrine of the Catholic Church addressing its aggiornamento, especially in what concerns to the employment of the modern ways of communication for the distance with the aim of evangelizing and educating. In arder to understand the ideaIs of the investigated educational Radio, we have delimited the research to the thematic Catholic Church, means of social communication and base education. In face of the study object and the aim to be reached it was appealed, methodologically, to the notion of cultural action present in Certeau (1995), and to the understanding of educational formation backgrounded fIam the modern thinkers that discuss it. Such frame references have allowed us to analyze in a wider spectrum tl)e programming broadcasted on the air by the sound wavys of that educ(itional Çatholic Radio, as well as, the very acts of cultural idealizations that has orientated it in its foundations. The thesis here defended is that. the Radio, at procJaiming itself as a broadcasting station of rural education directed preferably to the rural sertanejo countrymen, without neglecting its admitted ends, has surpassed them in its overall range. It was identified an articulate approach of its programmatic modules with the guid,elines emanateq from the Catholic Teaching about the use of the. means of social communication. At conceiving, establishin,g and executing an ec1ectic programmatic and div,ersified grating, the Rural Radio of Caicó has transcended to a strict human-Christian formation to request the development of the human, spiritual and cQrporaldimensions, jointly. With suchprogramming, it addressed to the seridoenses as real meu and women inserted in the "sertanej.o" environment with effective structural and existential problems of alI types, induding the hunger, the thirst, the syndical organization, the cQoperativism, the colIective modero work and the absence of universalizing school education. Its radiophonic transmissions, I}lled by the demands of an enlarged, open, dialogic and responsible communication, wheneIllbracing dedicated modules to religious and catechetical emissions, to the entertainment, to the radiojoumalism, to the country root culture, and to the school education of b se for the modality of the School and of the radiophonic classes, subsumed to ideaIs that longed for the formation of a multifaceted and pluridimensional sertanejo Man; of men and women that, without abjuring the Catholicism, were able to understand, to dialogued and to live together with the general demands of a society in progressive mutation, whose economical, social, cultural and educational demands it IDade themselves to be felt through the sertão potiguar of the Serido region, equal way of the intemationalized world

Redes de educação ambiental: um meio como proposta pedagógica para o mundo entrelaçado

The networks terminology has been growing in different meanings, in which emergent structures coming from one not so recently typology aquired, in the 90 s, fluid shapes impelled by waves without borders of the New Information and Communication Technologies. Ever since, the pattern and the morphology are being multiply and strengthen. With this backdrop, this study deals with the Education for Environment Networks, as a political and social, educative and cultural alternative intervention, as an answer for some contemporary demands. But what are these networks? In wich way they organize themselves to germinate political actions? Where is the core of these actions? What are their limits or potentialities? These are some of the questions that are presented along the study proposed. Therefore, we have in view to unveil the network social and environmental pedagogic dimension, as an alternative proposal towards to the planetary cintzenship formation for persons and coletivity. The study employs the exploration reasearch as the analysis of the organizational reference basis and the dinamics of conections that support the dialogue among the groups that belong to the Education for Environment Networks. We conclude that the networks overcome themselves as a powerfull tool to articulate and moblize people. They establish a potential pedagogic act for political and social intervention, as an alternative proposal for the citizen formation and his world vision. We sinalize that the networks are sometimes limited by the poorness of knowledge that still remains on those who find themselves twisted on them, and on the decreasing optics by those who are absent.

Análise e otimização de superfícies seletivas de Frequência utilizando redes neurais artificiais e algoritmos de otimização natural

The bidimensional periodic structures called frequency selective surfaces have been well investigated because of their filtering properties. Similar to the filters that work at the traditional radiofrequency band, such structures can behave as band-stop or pass-band filters, depending on the elements of the array (patch or aperture, respectively) and can be used for a variety of applications, such as: radomes, dichroic reflectors, waveguide filters, artificial magnetic conductors, microwave absorbers etc. To provide high-performance filtering properties at microwave bands, electromagnetic engineers have investigated various types of periodic structures: reconfigurable frequency selective screens, multilayered selective filters, as well as periodic arrays printed on anisotropic dielectric substrates and composed by fractal elements. In general, there is no closed form solution directly from a given desired frequency response to a corresponding device; thus, the analysis of its scattering characteristics requires the application of rigorous full-wave techniques. Besides that, due to the computational complexity of using a full-wave simulator to evaluate the frequency selective surface scattering variables, many electromagnetic engineers still use trial-and-error process until to achieve a given design criterion. As this procedure is very laborious and human dependent, optimization techniques are required to design practical periodic structures with desired filter specifications. Some authors have been employed neural networks and natural optimization algorithms, such as the genetic algorithms and the particle swarm optimization for the frequency selective surface design and optimization. This work has as objective the accomplishment of a rigorous study about the electromagnetic behavior of the periodic structures, enabling the design of efficient devices applied to microwave band. For this, artificial neural networks are used together with natural optimization techniques, allowing the accurate and efficient investigation of various types of frequency selective surfaces, in a simple and fast manner, becoming a powerful tool for the design and optimization of such structures

Desenvolvimento de antenas de microfita e antenas DRA Broadband

The search for ever smaller device and without loss of performance has been increasingly investigated by researchers involving applied electromagnetics. Antennas using ceramics materials with a high dielectric constant, whether acting as a substract element of patch radiating or as the radiant element are in evidence in current research, that due to the numerous advantages offered, such as: low profile, ability to reduce the its dimensions when compared to other devices, high efficiency of ratiation, suitability the microwave range and/or millimeter wave, low temperature coefficient and low cost. The reason for this high efficiency is that the dielectric losses of ceramics are very low when compared to commercially materials sold used in printed circuit boards, such as fiberglass and phenolite. These characteristics make ceramic devices suitable for operation in the microwave band. Combining the design of patch antennas and/or dielectric resonator antenna (DRA) to certain materials and the method of synthesis of these powders in the manufacture of devices, it s possible choose a material with a dielectric constant appropriate for the design of an antenna with the desired size. The main aim of this work is the design of patch antennas and DRA antennas on synthesis of ceramic powders (synthesis by combustion and polymeric precursors - Pe- chini method) nanostructured with applications in the microwave band. The conventional method of mix oxides was also used to obtain nanometric powders for the preparation of tablets and dielectric resonators. The devices manufactured and studied on high dielectric constant materials make them good candidates to have their small size compared to other devices operating at the same frequency band. The structures analyzed are excited by three different techniques: i) microstrip line, ii) aperture coupling and iii) inductive coupling. The efficiency of these techniques have been investigated experimentally and compared with simulations by Ansoft HFSS, used in the accurate analysis of the electromagnetic behavior of antennas over the finite element method (FEM). In this thesis a literature study on the theory of microstrip antennas and DRA antenna is performed. The same study is performed about the materials and methods of synthesis of ceramic powders, which are used in the manufacture of tablets and dielectric cylinders that make up the devices investigated. The dielectric media which were used to support the analysis of the DRA and/or patch antennas are analyzed using accurate simulations using the finite difference time domain (FDTD) based on the relative electrical permittivity (er) and loss tangent of these means (tand). This work also presents a study on artificial neural networks, showing the network architecture used and their characteristics, as well as the training algorithms that were used in training and modeling some parameters associated with the devices investigated

Estudo do acoplamento entre superfícies seletivas de frequência assimétricas em estruturas de multicamadas

This work presents the development of new microwaves structures, filters and high gain antenna, through the cascading of frequency selective surfaces, which uses fractals Dürer and Minkowski patches as elements, addition of an element obtained from the combination of the other two simple the cross dipole and the square spiral. Frequency selective surfaces (FSS) includes a large area of Telecommunications and have been widely used due to its low cost, low weight and ability to integrate with others microwaves circuits. They re especially important in several applications, such as airplane, antennas systems, radomes, rockets, missiles, etc. FSS applications in high frequency ranges have been investigated, as well as applications of cascading structures or multi-layer, and active FSS. In this work, we present results for simulated and measured transmission characteristics of cascaded structures (multilayer), aiming to investigate the behavior of the operation in terms of bandwidth, one of the major problems presented by frequency selective surfaces. Comparisons are made with simulated results, obtained using commercial software such as Ansoft DesignerTM v3 and measured results in the laboratory. Finally, some suggestions are presented for future works on this subject

Dinâmica da Plasticidade Sináptica em neurônios do hipocampo durante ciclos de sono: um estudo computacional

Several research lines show that sleep favors memory consolidation and learning. It has been proposed that the cognitive role of sleep is derived from a global scaling of synaptic weights, able to homeostatically restore the ability to learn new things, erasing memories overnight. This phenomenon is typical of slow-wave sleep (SWS) and characterized by non-Hebbian mechanisms, i.e., mechanisms independent of synchronous neuronal activity. Another view holds that sleep also triggers the specific enhancement of synaptic connections, carrying out the embossing of certain mnemonic traces within a lattice of synaptic weights rescaled each night. Such an embossing is understood as the combination of Hebbian and non-Hebbian mechanisms, capable of increasing and decreasing respectively the synaptic weights in complementary circuits, leading to selective memory improvement and a restructuring of synaptic configuration (SC) that can be crucial for the generation of new behaviors ( insights ). The empirical findings indicate that initiation of Hebbian plasticity during sleep occurs in the transition of the SWS to the stage of rapid eye movement (REM), possibly due to the significant differences between the firing rates regimes of the stages and the up-regulation of factors involved in longterm synaptic plasticity. In this study the theories of homeostasis and embossing were compared using an artificial neural network (ANN) fed with action potentials recorded in the hippocampus of rats during the sleep-wake cycle. In the simulation in which the ANN did not apply the long-term plasticity mechanisms during sleep (SWS-transition REM), the synaptic weights distribution was re-scaled inexorably, for its mean value proportional to the input firing rate, erasing the synaptic weights pattern that had been established initially. In contrast, when the long-term plasticity is modeled during the transition SWSREM, an increase of synaptic weights were observed in the range of initial/low values, redistributing effectively the weights in a way to reinforce a subset of synapses over time. The results suggest that a positive regulation coming from the long-term plasticity can completely change the role of sleep: its absence leads to forgetting; its presence leads to a positive mnemonic change

Análise e síntese de antenas e superfícies seletivas de frequência utilizando computação evolucionária e inteligência de enxames

The frequency selective surfaces, or FSS (Frequency Selective Surfaces), are structures consisting of periodic arrays of conductive elements, called patches, which are usually very thin and they are printed on dielectric layers, or by openings perforated on very thin metallic surfaces, for applications in bands of microwave and millimeter waves. These structures are often used in aircraft, missiles, satellites, radomes, antennae reflector, high gain antennas and microwave ovens, for example. The use of these structures has as main objective filter frequency bands that can be broadcast or rejection, depending on the specificity of the required application. In turn, the modern communication systems such as GSM (Global System for Mobile Communications), RFID (Radio Frequency Identification), Bluetooth, Wi-Fi and WiMAX, whose services are highly demanded by society, have required the development of antennas having, as its main features, and low cost profile, and reduced dimensions and weight. In this context, the microstrip antenna is presented as an excellent choice for communications systems today, because (in addition to meeting the requirements mentioned intrinsically) planar structures are easy to manufacture and integration with other components in microwave circuits. Consequently, the analysis and synthesis of these devices mainly, due to the high possibility of shapes, size and frequency of its elements has been carried out by full-wave models, such as the finite element method, the method of moments and finite difference time domain. However, these methods require an accurate despite great computational effort. In this context, computational intelligence (CI) has been used successfully in the design and optimization of microwave planar structures, as an auxiliary tool and very appropriate, given the complexity of the geometry of the antennas and the FSS considered. The computational intelligence is inspired by natural phenomena such as learning, perception and decision, using techniques such as artificial neural networks, fuzzy logic, fractal geometry and evolutionary computation. This work makes a study of application of computational intelligence using meta-heuristics such as genetic algorithms and swarm intelligence optimization of antennas and frequency selective surfaces. Genetic algorithms are computational search methods based on the theory of natural selection proposed by Darwin and genetics used to solve complex problems, eg, problems where the search space grows with the size of the problem. The particle swarm optimization characteristics including the use of intelligence collectively being applied to optimization problems in many areas of research. The main objective of this work is the use of computational intelligence, the analysis and synthesis of antennas and FSS. We considered the structures of a microstrip planar monopole, ring type, and a cross-dipole FSS. We developed algorithms and optimization results obtained for optimized geometries of antennas and FSS considered. To validate results were designed, constructed and measured several prototypes. The measured results showed excellent agreement with the simulated. Moreover, the results obtained in this study were compared to those simulated using a commercial software has been also observed an excellent agreement. Specifically, the efficiency of techniques used were CI evidenced by simulated and measured, aiming at optimizing the bandwidth of an antenna for wideband operation or UWB (Ultra Wideband), using a genetic algorithm and optimizing the bandwidth, by specifying the length of the air gap between two frequency selective surfaces, using an optimization algorithm particle swarm

Análise e projeto de superfícies seletivas de frequência com elementos pré-fractais para aplicações em comunicações indoor

In this thesis, a frequency selective surface (FSS) consists of a two-dimensional periodic structure mounted on a dielectric substrate, which is capable of selecting signals in one or more frequency bands of interest. In search of better performance, more compact dimensions, low cost manufacturing, among other characteristics, these periodic structures have been continually optimized over time. Due to its spectral characteristics, which are similar to band-stop or band-pass filters, the FSSs have been studied and used in several applications for more than four decades. The design of an FSS with a periodic structure composed by pre-fractal elements facilitates the tuning of these spatial filters and the adjustment of its electromagnetic parameters, enabling a compact design which generally has a stable frequency response and superior performance relative to its euclidean counterpart. The unique properties of geometric fractals have shown to be useful, mainly in the production of antennas and frequency selective surfaces, enabling innovative solutions and commercial applications in microwave range. In recent applications, the FSSs modify the indoor propagation environments (emerging concept called wireless building ). In this context, the use of pre-fractal elements has also shown promising results, allowing a more effective filtering of more than one frequency band with a single-layer structure. This thesis approaches the design of FSSs using pre-fractal elements based on Vicsek, Peano and teragons geometries, which act as band-stop spatial filters. The transmission properties of the periodic surfaces are analyzed to design compact and efficient devices with stable frequency responses, applicable to microwave frequency range and suitable for use in indoor communications. The results are discussed in terms of the electromagnetic effect resulting from the variation of parameters such as: fractal iteration number (or fractal level), scale factor, fractal dimension and periodicity of FSS, according the pre-fractal element applied on the surface. The analysis of the fractal dimension s influence on the resonant properties of a FSS is a new contribution in relation to researches about microwave devices that use fractal geometry. Due to its own characteristics and the geometric shape of the Peano pre-fractal elements, the reconfiguration possibility of these structures is also investigated and discussed. This thesis also approaches, the construction of efficient selective filters with new configurations of teragons pre-fractal patches, proposed to control the WLAN coverage in indoor environments by rejecting the signals in the bands of 2.4~2.5 GHz (IEEE 802.11 b) and 5.0~6.0 GHz (IEEE 802.11a). The FSSs are initially analyzed through simulations performed by commercial software s: Ansoft DesignerTM and HFSSTM. The fractal design methodology is validated by experimental characterization of the built prototypes, using alternatively, different measurement setups, with commercial horn antennas and microstrip monopoles fabricated for low cost measurements

Desenvolvimento de um ressoador retangular de fenda com múltiplas camadas de substrato e com utilização de material PBG para sistema de comunicação sem fio

In the globalized world modern telecommunications have assumed key role within the company, causing a large increase in demand for the wireless technology of communication, which has been happening in recent years have greatly increased the number of applications using this technology. Due to this demand, new materials are developed to enable new control mechanisms and propagation of electromagnetic waves. The research to develop new technologies for wireless communication presents a multidisciplinary study that covers from the new geometries for passive antennas, active up to the development of materials for devices that improve the performance at the frequency range of operation. Recently, planar antennas have attracted interest due to their characteristics and advantages when compared with other types of antennas. In the area of mobile communications the need for antennas of this type has become increasingly used, due to intensive development, which needs to operate in multifrequency antennas and broadband. The microstrip antennas have narrow bandwidth due to the dielectric losses generated by irradiation. Another limitation is the degradation of the radiation pattern due to the generation of surface waves in the substrate. Some techniques have been developed to minimize this limitation of bandwidth, such as the study of type materials PBG - Photonic Band Gap, to form the dielectric material. This work has as main objective the development project of a slot resonator with multiple layers and use the type PBG substrate, which carried out the optimization from the numerical analysis and then designed the device initially proposed for the band electromagnetic spectrum between 3-9 GHz, which basically includes the band S to X. Was used as the dielectric material RT/Duroid 5870 and RT/Duroid 6010.LM where both are laminated ceramic-filled PTFE dielectric constants 2.33 and 10.2, respectively. Through an experimental investigation was conducted an analysis of the simulated versus measured by observing the behavior of the radiation characteristics from the height variation of the dielectric multilayer substrates. We also used the LTT method resonators structures rectangular slot with multiple layers of material photonic PBG in order to obtain the resonance frequency and the entire theory involving the electromagnetic parameters of the structure under consideration. xviii The analysis developed in this work was performed using the method LTT - Transverse Transmission Line, in the field of Fourier transform that uses a component propagating in the y direction (transverse to the real direction of propagation z), thus treating the general equations of the fields electric and magnetic and function. The PBG theory is applied to obtain the relative permittivity of the polarizations for the sep photonic composite substrates material. The results are obtained with the commercial software Ansoft HFSS, used for accurate analysis of the electromagnetic behavior of the planar device under study through the Finite Element Method (FEM). Numerical computational results are presented in graphical form in two and three dimensions, playing in the parameters of return loss, frequency of radiation and radiation diagram, radiation efficiency and surface current for the device under study, and have as substrates, photonic materials and had been simulated in an appropriate computational tool. With respect to the planar device design study are presented in the simulated and measured results that show good agreement with measurements made. These results are mainly in the identification of resonance modes and determining the characteristics of the designed device, such as resonant frequency, return loss and radiation pattern

Otimização de superfícies seletivas de frequência com elementos pré-fractais utilizando rede neural MLP e algoritmos de busca populacional

This thesis describes design methodologies for frequency selective surfaces (FSSs) composed of periodic arrays of pre-fractals metallic patches on single-layer dielectrics (FR4, RT/duroid). Shapes presented by Sierpinski island and T fractal geometries are exploited to the simple design of efficient band-stop spatial filters with applications in the range of microwaves. Initial results are discussed in terms of the electromagnetic effect resulting from the variation of parameters such as, fractal iteration number (or fractal level), fractal iteration factor, and periodicity of FSS, depending on the used pre-fractal element (Sierpinski island or T fractal). The transmission properties of these proposed periodic arrays are investigated through simulations performed by Ansoft DesignerTM and Ansoft HFSSTM commercial softwares that run full-wave methods. To validate the employed methodology, FSS prototypes are selected for fabrication and measurement. The obtained results point to interesting features for FSS spatial filters: compactness, with high values of frequency compression factor; as well as stable frequency responses at oblique incidence of plane waves. This thesis also approaches, as it main focus, the application of an alternative electromagnetic (EM) optimization technique for analysis and synthesis of FSSs with fractal motifs. In application examples of this technique, Vicsek and Sierpinski pre-fractal elements are used in the optimal design of FSS structures. Based on computational intelligence tools, the proposed technique overcomes the high computational cost associated to the full-wave parametric analyzes. To this end, fast and accurate multilayer perceptron (MLP) neural network models are developed using different parameters as design input variables. These neural network models aim to calculate the cost function in the iterations of population-based search algorithms. Continuous genetic algorithm (GA), particle swarm optimization (PSO), and bees algorithm (BA) are used for FSSs optimization with specific resonant frequency and bandwidth. The performance of these algorithms is compared in terms of computational cost and numerical convergence. Consistent results can be verified by the excellent agreement obtained between simulations and measurements related to FSS prototypes built with a given fractal iteration

Desenvolvimento de circuitos planares sobre substratos têxteis

The use of flexible materials for the development of planar circuits is one of the most desired and studied characteristics, lately, by researchers. This happens because the flexibility of the substrate can provide previously impracticable applications, due to the rigidity of the substrates normally used that makes it difficult to fit into the circuits in irregular surfaces. The constant interest in recent years for more lighter devices, increasingly more compacts, flexible and with low cost, led to a new line of research of great interest from both academic and technological views, that is the study and development of textile substrates that can be applied in the development of planar circuits, for applications in the areas of security, biomedical and telecommunications. This paper proposes the development of planar circuits, such as antennas , frequency selective surfaces (FSS) and planar filters, using textile (cotton ticking, jeans and brim santista) as the dielectric substrate and the Pure Copper Polyester Taffeta Fabric, a textile of pure copper, highly conductive, lightweight and flexible, commercially sold as a conductive material. The electrical characteristics of textiles (electric permittivity and loss tangent) were characterized using the transmission line method (rectangular waveguide) and compared with those found in the literature. The structures were analyzed using commercial software Ansoft Designer and Ansoft HFSS, both from the company Ansys and for comparison we used the Iterative Method of Waves (WCIP). For the purpose of validation were built and measured several prototypes of antennas, planar filters and FSS, being possible to confirm an excellent agreement between simulated and measured results