Revestimentos a base de Ta/Al2O3 produzidos por aspersão térmica sobre substrato metálico

Metal substrates were coated by thermal spraying plasma torch, they were positioned at a distance of 4 and 5 cm from the nozzle exit of the plasma jet. The starting materials were used for deposition of tantalum oxide powder and aluminium. These two materials were mixed and ground into high-energy mill, then immersed in the torch for the production of alumina coating infused with particles of tantalum with nano and micrometric size. The spraying equipment used is a plasma torch arc not transferred, which operating in the range of 250 A and 80 V, was able to produce enough heat to ignite aluminothermic between Ta2O5 and aluminum. Upon reaching the plasma jet, the mixing powders react with the heat of the blaze, which provides sufficient energy for melting aluminum particles. This energy is transferred through mechanisms of self-propagating to the oxide, beginning a reduction reaction, which then hits on the surface of the substrate and forms a coating on which a composite is formed by a junction metal - ceramic (Ta +Al2O3). The phases and quantification of each were obtained respectively by X-ray diffraction and the Rietveld method. Morphology by scanning electron microscopy and chemical analysis by energy dispersive spectroscopy EDS. It was also performed measurements of the substrate roughness, Vickers microhardness measurements in sprays and determination of the electron temperature of the plasma jet by optical emission spectroscopy EEO. The results confirmed the expectation generated around the end product of spraying the mixture Ta2O5 + Al, both in the formation of nano-sized particles and in their final form. The electron excitation temperature was consistent with the purpose of work, in addition, the thermodynamic temperature was efficient for the reduction process of Ta2O5. The electron excitation temperature showed values of 3000, 4500 and 8000 K for flows10, 20 and 30 l / min respectively, these values were taken at the nozzle exit of the plasma jet. The thermodynamic temperature around 1200 ° C, was effective in the reduction process of Ta2O5

Medição de desempenho na cadeia de suprimentos da energia eólica: proposta de um conjunto de indicadores de desempenho

Performance measurement in highly competitive markets is a necessary measure for those who aim the top positions. The business performance measurement approach have reached relevant results in the literature, however, a different approach has recently appeared that broadened the perception of competition, where companies do not seek the competition among companies only, but also among supply chains. Brazilian Wind energy supply chain is living a structuring and expanding moment, with the major global players in the industry making investments in the country. This research aims to answer which are the key performance indicators that must be considered by the Brazilian wind energy sector companies, which are part in a broad perspective of supply chain competition. The research was executed in two steps: exploratory (literature review and a field research in the companies) and later a survey was conducted with the Brazilian Wind energy companies workers with the purpose to validate the performance indicators found in the exploratory step. The survey evaluated 40 performance indicators distributed among five major activities: Project prospection, building/execution, operation and maintenance, logistics and transverse processes, which summarize the performance of the entire supply chain, pointing the sinergy and the competitive level of the supply chain. The selected performance indicators reflect the high relevance of the costs dimension in the Brazilian energy companies performance, acting as a key performance indicator, is also indicates the limited performance management integration throughout the Brazilian wind energy supply chain

Protótipo de uma unidade com tri-geração de energia para utilizações remotas: aplicação de módulo secondutivo gerador termoelétrico

The generation for termoeletricity is characterized as a solid process of conversion of thermal energy (heat) in electric without the necessity of mobile parts. Although the conversion process is of low efficiency the system presents high degree of trustworthiness and low requisite of maintenance and durability. Its principle is based on the studies of termogeneration carried through by Thomas Seebeck in 1800. The frank development of the technologies of solid state for termoeletricity generation, the necessity of the best exploitation of the energy, also with incentive the cogeneration processes, the reduction of the ambient impact allies to the development of modules semiconductors of high efficiency, converge to the use of the thermoeletric generation through components of solid state in remote applications. The work presents the development, construction and performance evaluation of an prototype, in pilot scale, for energy tri-generation aiming at application in remote areas. The unit is composed of a gas lamp as primary source of energy, a module commercial semiconductor for thermoelectric generation and a shirt for production of the luminosity. The project of the device made compatible a headstock for adaptation in the gas lamp, a hot source for adaptation of the module, an exchanger of to be used heat as cold source and to compose first stage of cogeneration, an exchanger of tubular heat to compose second stage of cogeneration, the elaboration of a converter dc-dc type push pull, adequacy of a system of acquisition of temperature. It was become fullfilled assembly of the prototype in group of benches for tests and assay in the full load condition in order to evaluate its efficiency, had been carried through energy balance of the unit. The prototype presented an electric efficiency of 0,73%, thermal of 56,55%, illumination of 1,35% and global of 58,62%. The developed prototype, as the adopted methodology of assay had also taken care of to the considered objectives, making possible the attainment of conclusive results concerning to the experiment. Optimization in the system of setting of the semicondutor module, improvement in the thermal insulation and design of the prototype and system of protection to the user are suggestions to become it a commercial product

Capacidade de absorção de energia de tubos de compósitos submetidos à compressão

Structures capable of absorbing large amounts of energy are of great interest, particularly for the automotive and aviation industries, to reduce tbe impact on passengers in the case of a collision. The energy absorption properties of composite materials structures can be tailored, thus making these structures an appealing option a substitute of more traditional structures in applications where energy absorption is crucial. ln this research, the influence of some parameters, which affect the energy absorption capacity of composite material tubes, was investigated. The tubes were fabricated by hand lay-up, using orthophthalic polyester resin and a plain weave E-glass fabric Test specimens were prepared and tested under compression load. The ínfluence of the following parameters on the specific energy absorption capacity of the tubes was studied: fiber configuration (0/90º or ± 45°), tube cross-section (circular or square), and processing conditions (with or without vacuum). The results indicated that circular cross-section tubes with fibers oriented at 0/90º presented the highest level of specific energy absorbed. Further, specimens from tubes fabricated under vacuum displayed higher energy absorption capacity, when compared with specimens from tubes fabricated without vacuum. Thus, it can be concluded that the fabrication process with vacuum produce composite structures with better energy absorption capacity

Degradação catalítica de polietileno de alta densidade sobre a zeólita HZSM

In last years it has talked a lot about the environment and the plastic waste produced and discarded. In last decades, the increasing development of research to obtain fuel from plastic material, by catalytic degradation, it has become a very attractive looking, as these tailings are discarded to millions worldwide. These materials take a long time to degrade themselves by ways said natural and burning it has not demonstrated a viable alternative due to the toxic products produced during combustion. Such products could bring serious consequences to public health and environment. Therefore, the technique of chemical recycling is presented as a suitable alternative, especially since could be obtain fractions of liquid fuels that can be intended to the petrochemical industry. This work aims to propose alternatives to the use of plastic waste in the production of light petrochemical. Zeolites has been widely used in the study of this process due to its peculiar structural properties and its high acidity. In this work was studied the reaction of catalytic degradation of high-density polyethylene (HDPE) in the presence HZSM-12 zeolites with different acid sites concentrations by thermogravimetry and pyrolysis coupled with GC-MS. The samples of the catalysts were mixed with HDPE in the proportion of 50% in mass and submitted to thermogravimetric analyses in several heating rates. The addition of solids with different acid sites concentrations to HDPE, produced a decrease in the temperature of degradation of the polymer proportional the acidity of the catalyst. These qualitative results were complemented by the data of activation energy obtained through the non-isothermal kinetics model proposed by Vyazovkin. The values of Ea when correlated to the data of surface acidity of the catalysts indicated that there is a exponential decrease of the energy of activation in the reaction of catalytic degradation of HDPE, in function of the concentration of acid sites of the materials. These results indicate that the acidity of the catalyst added to the system is one of the most important properties in the reaction of catalytic degradation of polyethylene

Prospecção tecnológica para geração de energia eólica

The acceleration of technological change and the process of globalization has intensified competition and the need for new products (goods and services), resulting in growing concern for organizations in the development of technological, economic and social advances. This work presents an overview of the development of wind energy-related technologies and design trends. To conduct this research, it is (i) a literature review on technological innovation, technological forecasting methods and fundamentals of wind power; (ii) the analysis of patents, with the current technology landscape studied by means of finding information in patent databases; and (iii) the preparation of the map of technological development and construction of wind turbines of the future trend information from the literature and news from the sector studied. Step (ii) allowed the study of 25 644 patents between the years 2003-2012, in which the US and China lead the ranking of depositors and the American company General Electric and the Japanese Mitsubishi stand as the largest holder of wind technology. Step (iii) analyzed and identified that most of the innovations presented in the technological evolution of wind power are incremental product innovations to market. The proposed future trends shows that the future wind turbines tend to have a horizontal synchronous shaft, which with the highest diameter of 194m and 164m rotor nacelle top, the top having 7,5MW generation. The materials used for the blades are new materials with characteristics of low density and high strength. The towers are trend with hybrid materials, uniting the steel to the concrete. This work tries to cover the existing gap in the gym on the use of technological forecasting techniques for the wind energy industry, through the recognition that utilize the patent analysis, analysis of scientific articles and stories of the area, provide knowledge about the industry and influencing the quality of investment decisions in R & D and hence improves the efficiency and effectiveness of wind power generation

Análise do comportamento de técnicas de correspondência binocular para imagens em alta definição

This work presents an analysis of the behavior of some algorithms usually available in stereo correspondence literature, with full HD images (1920x1080 pixels) to establish, within the precision dilemma versus runtime applications which these methods can be better used. The images are obtained by a system composed of a stereo camera coupled to a computer via a capture board. The OpenCV library is used for computer vision operations and processing images involved. The algorithms discussed are an overall method of search for matching blocks with the Sum of the Absolute Value of the difference (Sum of Absolute Differences - SAD), a global technique based on cutting energy graph cuts, and a so-called matching technique semi -global. The criteria for analysis are processing time, the consumption of heap memory and the mean absolute error of disparity maps generated.