Paralelização em GPU da segmentação vascular com extração de Centerlines por Height Ridges

The vascular segmentation is important in diagnosing vascular diseases like stroke and is hampered by noise in the image and very thin vessels that can pass unnoticed. One way to accomplish the segmentation is extracting the centerline of the vessel with height ridges, which uses the intensity as features for segmentation. This process can take from seconds to minutes, depending on the current technology employed. In order to accelerate the segmentation method proposed by Aylward [Aylward & Bullitt 2002] we have adapted it to run in parallel using CUDA architecture. The performance of the segmentation method running on GPU is compared to both the same method running on CPU and the original Aylward s method running also in CPU. The improvemente of the new method over the original one is twofold: the starting point for the segmentation process is not a single point in the blood vessel but a volume, thereby making it easier for the user to segment a region of interest, and; the overall gain method was 873 times faster running on GPU and 150 times more fast running on the CPU than the original CPU in Aylward

Otimização da extração de polissacarídeos sulfatados da alga vermelha Gracilaria birdiae e análise da atividade anticoagulante e antioxidante

The sulfated polysaccharides (SP) from the edible red seaweed Gracilaria birdiae were obtained using five different condition extraction (GB1: Water; GB1p: Water/proteolysis; GB1s: Water/sonication; GB1sp: Water/sonication/proteolysis; GB2s: NaOH/sonication; GB2sp: NaOH/sonication/proteolysis. The yield (g) increased in the following order GB2sp>GB1sp>GB1p>GB2s>GB1s>GB1. However, the amount of SP extracted increased in different way GB2sp>GB1p>GB1>GB1sp>GB1s>GB2s. Infrared and electrophoresis analysis showed that all conditions extracted the same SP. In addition, monosaccharide composition showed that ultrasound promotes the extraction of other polysaccharides than SP. In the prothrombin time (PT) test, which evaluates the extrinsic coagulation pathway, none of the samples showed anticoagulant activity. While in the activated partial thromboplastin time (aPTT) test, which evaluates the intrinsic coagulation pathway, all samples showed anticoagulant activity, except GB2s. The aPTT activity decreased in the order of GB1sp>GB2sp>GB1p>GB1>GB1s>GB2s. Total capacity antioxidant (TCA) of the SP was also affected by condition extraction, since GB2s and GB1 showed lower activity in comparison to the other conditions. In conclusion, the conditions of SP extraction influence their biological activities and chemical composition. The data showed NaOH/sonication/proteolysis was the best condition to extract anticoagulant and antioxidant SPs from Gracilaria birdiae.

Determinação de CD, PB, e TL em água produzida por HR-CS GF AAS após extração em ponto nuvem

Produced water is a major problem associated with the crude oil extraction activity. The monitoring of the levels of metals in the waste is constant and requires the use of sensitive analytical techniques. However, the determination of trace elements can often require a pre-concentration step. The objective of this study was to develop a simple and rapid analytical method for the extraction and pre-concentration based on extraction phenomenon cloud point for the determination of Cd, Pb and Tl in produced water samples by spectrometry of high resolution Absorption source continues and atomization graphite furnace. The Box Behnken design was used to obtain the optimal condition of extraction of analytes. The factors were evaluated: concentration of complexing agent (o,o-dietilditilfosfato ammonium, DDTP), the concentration of hydrochloric acid and concentration of surfactant (Triton X -114). The optimal condition obtained through extraction was: 0,6% m v-1 DDTP, HCl 0,3 mol L-1 and 0,2% m v-1 of Triton X - 114 for Pb; 0,7% m v-1 DDTP, HCl 0,8 mol L-1 and 0,2% m v-1 Triton X-114 for Cd. For Tl was evidenced that best extraction condition occurs with no DDTP, the extraction conditions were HCl 1,0 mol L-1 e 1,0% m v-1 de Triton X - 114. The limits of detection for the proposed method were 0,005 µg L-1 , 0,03 µg L-1 and 0,09 µg L-1 to Cd, Pb and Tl, Respectively. Enrichment factors Were greater than 10 times. The method was applied to the water produced in the Potiguar basin, and addition and recovery tests were performed, and values were between 81% and 120%. The precision was expressed with relative standard deviation (RSD) is less than 5%

Extração do corante do fruto de castanhola (Terminalia catappa Linn) e estudos dos seus compostos fenólicos, antocianinas e atividade antioxidante

The Terminalia catappa Linn belonging to Combretaceae family, popularly known as castanets, has fruits consists of a fleshy pulp, rounded seed and a very hard shell. The natural pigmentation existing in the fruit of castanet indicates the presence of anthocyanins, phenolic nature components belonging to the group of flavonoids, which have antioxidant activity. This research was conducted with the castanets and aimed to the study of factors influencing the extraction of dyes from its pulp. The extracts were obtained using a reactor enjaquetado by solid-liquid extraction. The factors were evaluated as temperature, time, solvent ratio and pH extraction. Adopting a factorial design of 24 , with 4 repetitions at the central point, the effects of these factors on the extraction process were analyzed using Statistica 7.0 software. The antioxidant activity (AA), the content of phenolic compounds (CFT) and the total monomeric anthocyanin content (AMT) were evaluated as response variables planning. Statistical analysis of the results, the effects that influenced the extraction were different for each response (CFT, AMT and AA). However, the pH was significant for the extraction of all compounds. The kinetic behavior of the dye extraction was also studied for phenolic compounds, monomeric anthocyanins and antioxidant activity, in which the equilibrium was reached after 90 minutes of extraction. To study the stability of anthocyanins temperature was the factor that most influenced the stability, however the concentration and pH also played a part.

Desenvolvimento de metodologia de extração e pré-concentração utilizando sistema microemulsionado para determinação de Cd, Co, Cu, Ni, Pb e Tl em águas naturais e produzidas por HR-CS AAS

The determination and monitoring of metallic contaminants in water is a task that must be continuous, leading to the importance of the development, modification and optimization of analytical methodologies capab le of determining the various metal contaminants in natural environments, because, in many cases, the ava ilable instrumentation does not provide enough sensibility for the determination of trace values . In this study, a method of extraction and pre- concentration using a microemulsion system with in the Winsor II equilibrium was tested and optimized for the determination of Co, Cd, P b, Tl, Cu and Ni through the technique of high- resolution atomic absorption spectrometry using a continuum source (HR-CS AAS). The optimization of the temperature program for the graphite furnace (HR-CS AAS GF) was performed through the pyrolysis and atomization curves for the analytes Cd, Pb, Co and Tl with and without the use of different chemical modifiers. Cu and Ni we re analyzed by flame atomization (HR-CS F AAS) after pre-concentr ation, having the sample introduction system optimized for the realization of discrete sampling. Salinity and pH levels were also analyzed as influencing factors in the efficiency of the extraction. As final numbers, 6 g L -1 of Na (as NaCl) and 1% of HNO 3 (v/v) were defined. For the determination of the optimum extraction point, a centroid-simplex statistical plan was a pplied, having chosen as the optimum points of extraction for all of the analytes, the follo wing proportions: 70% aqueous phase, 10% oil phase and 20% co-surfactant/surfactant (C/S = 4). After extraction, the metals were determined and the merit figures obtained for the proposed method were: LOD 0,09, 0,01, 0,06, 0,05, 0,6 and 1,5 μg L -1 for Pb, Cd, Tl, Co, Cu and Ni, re spectively. Line ar ranges of ,1- 2,0 μg L -1 for Pb, 0,01-2,0 μg L -1 for Cd, 1,0 - 20 μg L -1 for Tl, 0,1-5,0 μg L -1 for Co, 2-200 μg L -1 and for Cu e Ni 5-200 μg L -1 were obtained. The enrichment factors obtained ranged between 6 and 19. Recovery testing with the certified sample show ed recovery values (n = 3, certified values) after extraction of 105 and 101, 100 and 104% for Pb, Cd, Cu and Ni respectively. Samples of sweet waters of lake Jiqui, saline water from Potengi river and water produced from the oil industry (PETROBRAS) were spiked and the recovery (n = 3) for the analytes were between 80 and 112% confirming th at the proposed method can be used in the extraction. The proposed method enabled the sepa ration of metals from complex matrices, and with good pre-concentration factor, consistent with the MPV (allowed limits) compared to CONAMA Resolution No. 357/2005 which regulat es the quality of fresh surface water, brackish and saline water in Brazil.

Remoção de corantes utilizando tensoativos: extração por ponto de nuvem e floculação iônica

The textile sector is one of the main contributors to the generation of industrial wastewaters due to the use of large volumes of water, which has a high organic load content. In these, it is observed to the presence of dyes, surfactants, starch, alcohols, acetic acid and other constituents, from the various processing steps of the textiles. Hence, the treatment of textile wastewater becomes fundamental before releasing it into water bodies, where they can cause disastrous physical-chemical changes for the environment. Surfactants are substances widely used in separation processes and their use for treating textile wastewaters was evaluated in this research by applying the cloud point extraction and the ionic flocculation. In the cloud point extraction was used as surfactant nonylphenol with 9.5 ethoxylation degree to remove reactive dye. The process evaluation was performed in terms of temperature, surfactant and dye concentrations. The dye removal reached 91%. The ionic flocculation occurs due to the presence of calcium, which reacts with anionic surfactant to form insoluble surfactants capable of attracting the organic matter by adsorption. In this work the ionic flocculation using base soap was applied to the treatment of synthetic wastewater containing dyes belonging to three classes: direct, reactive, and disperse. It was evaluated by the influence of the following parameters: surfactant and electrolyte concentrations, stirring speed, equilibrium time, temperature, and pH. The flocculation of the surfactant was carried out in two ways: forming the floc in the effluent itself and forming the floc before mixing it to the effluent. Removal of reactive and direct dye, when the floc is formed into textile effluent was 97% and 87%, respectively. In the case where the floc is formed prior to adding it to the effluent, the removal to direct and disperse dye reached 92% and 87%, respectively. These results show the efficience of the evaluated processes for dye removal from textile wastewaters.

Extração, caracterização e avaliação bioativa do extrato de Arrabidaea chica

The use of plants for medicinal purposes is ancient, with widespread application in medicinal drugs. Although plants are promising sources for the discovery of new molecules of pharmacological interest, estimates show that only 17% of them have been studied for their possible use in medicine. Thus, biodiversity of Brazilian flora represents an immense potential for economic use by the pharmaceutical industry. The plant Arrabidaea chica, popularly known as “pariri”, is common in the Amazon region, and it is assigned several medicinal properties. The leaves of this plant are rich in anthocyanins, which are phenolic compounds with high antioxidant power. Antioxidant compounds play a vital role in the prevention of neurological and cardiovascular diseases, cancer and diabetes, among others. Within the anthocyanins found in Arrabidaea chica, stands out Carajurin (6,7-dihydroxy-5,4’- dimethoxy-flavilium), which is the major pigment encountered in this plant. The present work aimed to study on supercritical extraction and conventional extraction (solid-liquid extraction) in leaves of Arrabidaea chica, evaluating the efficiency of the extractive processes, antioxidant activity and quantification of Carajurin contained in the extracts. Supercritical extraction used CO2 as solvent with addition of co-solvent (ethanol/water mixture) and were conducted by the dynamic method in a fixed bed extractor. The trials followed a 24-1 fractional factorial design, the dependent variables were: process yield, concentration of Carajurin and antioxidant activity; and independent variables were: pressure, temperature, concentration of co-solvent (v/v) and concentration of water in the co-solvent mixture (v/v). Yields (mass of dry extract/mass of raw material used) obtained from supercritical extraction ranged from 15.1% to 32%, and the best result was obtained at 250 bar and 40 °C, co-solvent concentration equal to 30% and concentration of water in the co-solvent mixture equal to 50%. Through statistical analysis, it was found that the concentration of co-solvent revealed significant effect on the yield. Yields obtained from conventional extractions were of 8.1% (water) and 5.5% (ethanol). Through HPLC (High-performance liquid chromatography) analysis, Carajurin was quantified in all the extracts and concentration values (Carajurin mass/mass of dry extract) ranged between 1% and 2.21% for supercritical extraction. For conventional extraction, Carajurin was not detected in the aqueous extract, while the ethanol extract showed Carajurin content of 7.04%, and therefore, more selective in Carajurin than the supercritical extraction. Evaluation of antioxidant power (radical 2,2-diphenyl-1-picrylhydrazyl – DPPH – sequestration method) of the supercritical extracts resulted in EC50 values (effective concentration which neutralizes 50% of free radicals) ranged from 38.34 to 86.13 μg/mL, while conventional extraction resulted in EC50 values of 167.34 (water) and 42.58 (ethanol) μg/mL. As for the quantification of total phenolic content (Folin-Ciocalteau analysis) of the supercritical extracts resulted in values ranged from 48.93 and 88.62 mg GAE/g extract (GAE = Gallic Acid Equivalents), while solid-liquid extraction resulted in values of 37.63 (water) and 80.54 (ethanol) mg GAE/g extract. The good antioxidant activity cannot be attributed solely to the presence of Carajurin, but also the existence of other compounds and antioxidants in Arrabidaea chica. By optimizing the experimental design, it was possible to identify the experiment that presented the best result considering the four dependent variables together. This experiment was performed under the following conditions: pressure of 200 bar, temperature of 40 °C, co-solvent concentration equal to 30% and concentration of water in the co-solvent mixture equal to 30%. It is concluded that, within the studied range, it is possible to purchase the optimum result using milder operating conditions, which implies lower costs and greater ease of operation.

Extração, caracterização e prospecção de atividades farmacológicas de polissacarídeos sulfatados da macroalga verde Caulerpa prolifera

This study aimed to extract, characterize and conduct a prospective analysis of pharmacological activities of sulfated polysaccharides from green seaweed Caulerpa prolifera. Seven fractions (CP-0.3/CP-0.5/CP-0.7/CP-0.9/CP-1.1/CP-1.5/CP-2.0) were obtained from C. prolifera by alkaline proteolysis followed by sequential precipitation in acetone. The physicochemical analyzes indicated that C. prolifera synthesizes a homogalactan (CP-0.9) and different populations of sulfated heteropolysaccharides. In the analysis of anticoagulant activity, all fractions except CP-0.3, influenced the intrinsic coagulation pathway. All fractions showed antioxidant activity in six different assays being more pronounced in hydrogen peroxide scavenging assay, especially CP-0.3, CP-0.7 and CP-0.9 (which obtained 61% of hydrogen peroxide scavenging), in ferric chelation assay (especially CP-0.9 with 56% chelation) and cupric chelation assay (especially CP-2.0 with 78% chelation). With respect to immunomodulatory activity, the presence of CP-0.3, CP-0.7 and CP-0.9 showed an immunogenic potential, increasing the production of nitric oxide (NO) by 48, 142 and 163 times, respectively. Conversely, the NO synthesis fell 73% after the activation of macrophages by LPS, incubated concurrently with CP-2.0. The anti-adipogenic activity of the fractions was also evaluated and CP-1.5 was able to reduce the differentiation of pre-adipocytes (3T3-L1) into adipocytes by 60%, without affecting the cell viability. The fractions CP-0.3, CP-0.5 and CP-0.9 reduced the viability of the HeLa cells (human cervical adenocarcinoma) by 55% and CP-1.5 reduced the viability of the 786-0 cells (human renal adenocarcinoma) by 75%. Leishmanicidal activity and microbicide effect against Carbapenem-resistant Klebsiella pneumoniae (KPC) have not been identified. However, the viability of Staphylococcus epidermidis was reduced by 23.8% in the presence of CP -1.5. All fractions were able to change the formation of calcium oxalate crystals. CP-0.3, CP-0.5 and CP-1.1 only promoted the formation of COD type crystals with a very small size (1 μm). Confocal microscopy and zeta potential data of crystals formed in the presence of the samples showed that the polysaccharides present in the fractions must interact with calcium ions present throughout the crystal lattice, affecting the growth and morphology of crystals The results described herein indicate that the fractions rich in polysaccharides obtained from the green seaweed C. prolifera present a multi therapeutic potential, and subsequent purification steps, as well as research on the mechanisms of action by which these polymers act should be investigated.

Uso de correntropia na generalização de funções cicloestacionárias e aplicações para a extração de características de sinais modulados

Information extraction is a frequent and relevant problem in digital signal processing. In the past few years, different methods have been utilized for the parameterization of signals and the achievement of efficient descriptors. When the signals possess statistical cyclostationary properties, the Cyclic Autocorrelation Function (CAF) and the Spectral Cyclic Density (SCD) can be used to extract second-order cyclostationary information. However, second-order cyclostationary information is poor in nongaussian signals, as the cyclostationary analysis in this case should comprise higher-order statistical information. This paper proposes a new mathematical tool for the higher-order cyclostationary analysis based on the correntropy function. Specifically, the cyclostationary analysis is revisited focusing on the information theory, while the Cyclic Correntropy Function (CCF) and Cyclic Correntropy Spectral Density (CCSD) are also defined. Besides, it is analytically proven that the CCF contains information regarding second- and higher-order cyclostationary moments, being a generalization of the CAF. The performance of the aforementioned new functions in the extraction of higher-order cyclostationary characteristics is analyzed in a wireless communication system where nongaussian noise exists.

Efeitos da microgravidade em plantas de cana-de-açúcar

Sugarcane (Saccharum spp.) is a plant from Poaceae family that has an impressive ability to accumulate sucrose in the stalk, making it a significant component of the economy of many countries. About 100 countries produce sugarcane in an area of 22 million hectares worldwide. For this reason, many studies have been done using sugarcane as a plant model in order to improve production. A change in gravity may be one kind of abiotic stress, since it generates rapid responses after stimulation. In this work we decided to investigate the possible morphophysiological, biochemical and molecular changes resulting from microgravity. Here, we present the contributions of an experiment where sugarcane plants were submitted to microgravity flight using a vehicle VSB-30, a sounding rocket developed by Aeronautics and Space Institute teams, in cooperation with the German Space Agency. Sugarcane plants with 10 days older were submitted to a period of six minutes of microgravity using the VSB-30 rocket. The morphophysiological analyses of roots and leaves showed that plants submitted to the flight showed changes in the conduction tissues, irregular pattern of arrangement of vascular bundles and thickening of the cell walls, among other anatomical changes that indicate that the morphology of the plants was substantially influenced by gravitational stimulation, besides the accumulation of hydrogen peroxide, an important signaling molecule in stress conditions. We carried out RNA extraction and sequencing using Illumina platform. Plants subjected to microgravity also showed changes in enzyme activity. It was observed an increased in superoxide dismutase activity in leaves and a decreased in its activity in roots as well as for ascorbate peroxidase activity. Thus, it was concluded that the changes in gravity were perceived by plants, and that microgravity environment triggered changes associated with a reactive oxygen specie signaling process. This work has helped the understanding of how the gravity affects the structural organization of the plants, by comparing the anatomy of plants subjected to microgravity and plants grown in 1g gravity

Extração, caracterização estrutural parcial e atividades farmacológicas do olginato obtido da alga marrom Lobophora variegata (Lamouroux) Oliveira Filho, 1977

The alginic acid or alginates are acidic polysaccharides found in brown seaweed widely used in food, cosmetic, medical and pharmaceutical industry. This paper proposes the extraction, chemical characterization and verification of the pharmacological activities of brown seaweed variegata Lobophora . The alginate was extracted from the seaweed Lobophora variegata and part was sulphated for comparative purposes. The native extract showed 42% total sugar, 65% uronic acid, 0,36 % protein and 0% of sulfate, while the sulfate showed 39% , 60%, 0.36% and 27,92 % respectively. The presence of a sulfate group may be observed by the metachromasia with toluidine blue in electrophoresis system and characteristic vibration 1262,34 cm-1 in infrared spectroscopy connections assigned to S = O. We observed the formation of films and beads of native alginate, where more concentrated solution 6% resulted in a thicker and more consistent film. Native alginate showed proliferative activity at concentrations (25 and 50 mcg), (50 mg) and (100 mg) in 3T3 cell line in 24h, 48h and 72h, respectively , as the sulfated (100 mg) in 24 . Also showed antiproliferative or cytotoxic activity in HeLa cells of strain, (25 and 100 mg), (25 and 100 mg) and (25, 50 and 100 mg), to native, now for the sulfate concentrations (100 mg) in 24 (25, 50 and 100 mg) in 48 hours, and (50 and 100 mg ) 72h. For their antioxidant activity, the sulfated alginates have better total antioxidant activity reaching 29 % of the native activity while 7.5 % of activity . For the hydroxyl radical AS showed high inhibition ( between 77-83 % ) in concentrations, but the AN surpassed these numbers in the order of 78-92 % inhibition. The reducing power of AN and AS ranged between 39-82 % . In the method of ferric chelation NA reached 100 % chelating while the AS remained at a plateau oscillating 6.5%. However, in this study , we found alginates with promising pharmacological activities, to use in various industries as an antioxidant / anti-tumor compound

Estudo da adição do resíduo proveniente da extração de minério de ferro em argilas do Rio Grande do Norte

The mining industry is responsible for the generation of waste from their natural process of extraction. The mining impacts in urban areas are of special importance due to the high urban occupation, which are exacerbated due to the proximity of the mined areas and populated areas. Some solutions to wastedisposal have the potential to significantly reduce the environmental risks and liabilities, but represent higher costs in the stages of deployment and operation. The addition of mining waste as raw material in the development of commercial products reduces the environmental impacts, transforming the waste into a positive element in the generation of employment and income. This thesis studies the incorporation of waste iron ore in two clays, one from the ceramic industry of the City of Natal and the other from the ceramic industry of the Seridó Region, both in the State of Rio Grande do Norte, Brazil. Percentages of iron ore waste of 5%, 10% , 15%, 20%, 25% and 30% were used in the tested ceramic matrix. The two clays and the iron ore waste used as part of this investigation were characterized by X-ray diffraction tests, X-ray fluorescence tests, differential thermal analysis, thermogravimetric analysis and dilatometric analysis. The samples were sintered under temperatures of 850 °C, 950 °C and 1050°C at a heating rate of 5 °C/min with isotherms of two hours. The following tests were performed with the samples: linear shrinkage, water absorption, apparent porosity, apparent density, mass loss in fire and bending resistance in order to obtain their physical and mechanical properties. An amount of 5% of waste iron ore in the matrix clay at a temperature of 850 0C resulted in na increase of about 65% in the tensile strength of the clay samples from the Natal ceramic industry. A linear shrinkage of only 0.12% was observed for the samples, which indicates that the physical properties of the final product were not influenced by the addition of the waste

Síntese enzimática de ésteres de açúcar: surfactantes e polímeros como novos materiais ambientalmente seguros

Sugar esters are substances which possess surfactant, antifungical and bactericidal actions and can be obtained through two renewable sources of raw materials: sugars and vegetable oils. Their excellent biodegradability, allied to lhe fact that they are non toxic, insipid, inodorous, biocompatible, no-ionic, digestible and because they can resist to adverse conditions of temperature, pH and salinity, explain lhe crescent use of these substances in several sections of lhe industry. The objective of this thesis was to synthesize and characterize surfactants and polymers containing sugar branched in their structures, through enzymatic transesterification of vinyl esters and sugars, using alkaline protease from Bacillus subtilis as catalyst, in organic medium (DMF).Three types of sugars were used: L-arabinose, D-glucose and sucrose and two types of vinyl esters: vinyl laurate and vinyl adipate. Aiming to reach high conversions from substrates to products for a possible future large scale industrial production, a serie of variables was optimized, through Design of Experiments (DOE), using Response Surface Methodology (RSM).The investigated variables were: (1) enzyme concentration; (2) molar reason of substrates; (3) water/solvent rale; (4) temperature and (5) time. We obtained six distinct sugar esters: 5-0-lauroyl L-arabinose, 6-0-lauroyl D-glucose, 1'-O-lauroyl sucrose, 5-0-vinyladipoyl L-arabinose, 6-0-vinyladipoyl D-glucose and 1 '-O-vinyladipoyl sucrose, being lhe last three polymerizable. The progress of lhe reaction was monitored by HPLC analysis, through lhe decrease of sugar concentration in comparison to lhe blank. Qualitative analysis by TLC confirmed lhe formation of lhe products. In lhe purification step, two methodologies were adopted: (1) chromatographic column and (2) extraction with hot acetone. The acylation position and lhe chemical structure were determined by 13C-RMN. The polymerization of lhe three vinyl sugar esters was possible, through chemical catalysis, using H2O2 and K2S2O8 as initiators, at 60°C, for 24 hours. IR spectra of lhe monomers and respective polymers were compared revealing lhe disappearance of lhe vinyl group in lhe polymer spectra. The molar weights of lhe polymers were determined by GPC and presented lhe following results: poly (5-0-vinyladipoyl L-arabinose): Mw = 7.2 X 104; PD = 2.48; poly (6-0-vinyladipoyl D-glucose): Mw = 2.7 X 103; PD = 1.75 and poly (1'-O-vinyladipoyl sucrose): Mw = 4.2 X 104; PD = 6.57. The six sugar esters were submitted to superficial tension tests for determination of the critical micelle concentrations (CMC), which varied from 122 to 167 ppm. Finally, a study of applicability of these sugar esters, as lubricants for completion fluids of petroleum wells was' accomplished through comparative analysis of lhe efficiency of these sugar esters, in relation to three commercial lubricants. The products synthesized in this thesis presented equivalent or superior action to lhe tested commercial products

Extração de boro de água produzida sintética por sistema microemulsionado

Boron is a semi-metal present in certain types of soils and natural waters. It is essential to the healthy development of plants and non-toxic to humans, depending on its concentration. It is used in various industries and it s present in water production coming from oil production. More specifically in Rio Grande do Norte, one of the largest oil producers on shore of Brazil, the relationship water/oil in some fields becomes more than 90%. The most common destination of this produced water is disposal in open sea after processing to meet the legal specification. In this context, this research proposes to study the extraction of boron in water produced by microemulsion systems for industrial utilization. It was taken into account the efficiency of extraction of boron related to surfactant (DDA and OCS, both characterized by FT-IR), cosurfactant (butanol and isoamyl alcohol), organic phase (kerosene and heptanes) and aqueous phase (solution of boron 3.6 ppm in alkaline pH). The ratio cosurfactant/ surfactant used was four and the percentage of organic phases for all points of study was set at 5%. It was chosen points with the highest percentage of aqueous phase. Each system was designed for three points of different compositions in relation to the constituents of a pseudoternary diagram. These points were chosen according to studies of phase behavior in pseudoternary diagrams made in previous studies. For this research, points were chosen in the Winsor II region. The excess aqueous solution obtained in these systems was separated and analyzed by ICP OES. For the data set obtained, the better efficiency in the extraction of boron was obtained using the system with DAC, isoamyl alcohol and heptanes, which extracted 49% in a single step. OCS was not viable to the extraction of boron by microemulsion system in the conditions defined in this study

Extração de metais (K, Mg, Ba, Ca, Cr, Mn, Li, Fe) de água produzida utilizando sistema microemulsionado

The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation