Obtenção e caracterização de um compósito de matriz polimérica com carga de bucha vegetal luffa cylindrica

Composite materials arise from the need for lighter materials and with bigger mechanical and thermal resistance. The difficulties of discard, recycling or reuse are currently environmental concerns and, therefore, they are study object of much researches. In this perspective the feasibility of using loofahs (Luffa Cylindrica) for obtainment of a polymeric matrix composite was studied. Six formulations, with 4, 5 and 6 treated layers and untreated, were tested. The loofahs were treated in boiling water to remove lignins, waxes and impurities present in the fibers. After that, they were dried in a direct exposure solar dryer. For the characterization of the composite, thermal (thermal conductivity, thermal capacity, thermal diffusivity and thermal resistivity), mechanical (tensile and bending resistance) and physicochemical (SEM, XRD, density, absorption and degradation) properties were determined. The proposed composite has as advantage the low fiber density, which is around 0.66 g/cm³ (almost half of the polyester resin matrix), resulting in an average composite density of around 1.17g/cm³, 6.0 % lower in relation to the matrix. The treatment carried out in the loofahs increased the mechanical strength of the composite and decreased the humidity absorption. The composite showed lower mechanical behavior than the matrix for all the formulations. The composite also demonstrated itself to be feasible for thermal applications, with a value of thermal conductivity of less than 0.159 W/m.K, ranking it as a good thermal insulator. For all formulations/settings a low adherence between fibers and matrix occurred, with the presence of cracks, showing the fragility due to low impregnation of the fiber by the matrix. This composite can be used to manufacture structures that do not require significant mechanical strength, such as solar prototypes, as ovens and stoves.

Estudo da evolução das tensões residuais através da difratometria de raios x em aço rolamento submetido a esforços cíclicos

The micro-deformations caused by cyclic loading origins the variation of the distances between atoms of the crystal lattice producing the irreversible component. In order to study and understand the microstructural behavior of the material this paper investigated the influence suffered by residual stresses in thrust rolling bearing races fabricated in AISI 52100 steel, after tests by cyclic rolling contact in a tribometer at 1m/s under two contact pressures (500 MPa and 1400 MPa) in dry and boundary lubrication conditions. Procedures of tests thermo-acustically isolated were developed for monitoring the contact temperature and sound pressure level signals to establish a comparison between the residual stress measurements, micro-hardness Vickers and micrographic registers searching an indication of wear evolution. The sin²ψ method by X-ray diffraction technique was used to quantify the residual stresses. Three raceway zones were selected for the evaluation of wear and surface morphology after predetermined cycling, comparing with their new condition ("as received"). Micro-hardness and residual stress measurements showed significant changes after the tests and it was possible to observe the relationship between the increase of sound pressure level and the residual stress for dry and lubricated conditions.

Estudo da evolução das tensões residuais através da difratometria de raios x em aço rolamento submetido a esforços cíclicos

The micro-deformations caused by cyclic loading origins the variation of the distances between atoms of the crystal lattice producing the irreversible component. In order to study and understand the microstructural behavior of the material this paper investigated the influence suffered by residual stresses in thrust rolling bearing races fabricated in AISI 52100 steel, after tests by cyclic rolling contact in a tribometer at 1m/s under two contact pressures (500 MPa and 1400 MPa) in dry and boundary lubrication conditions. Procedures of tests thermo-acustically isolated were developed for monitoring the contact temperature and sound pressure level signals to establish a comparison between the residual stress measurements, micro-hardness Vickers and micrographic registers searching an indication of wear evolution. The sin²ψ method by X-ray diffraction technique was used to quantify the residual stresses. Three raceway zones were selected for the evaluation of wear and surface morphology after predetermined cycling, comparing with their new condition ("as received"). Micro-hardness and residual stress measurements showed significant changes after the tests and it was possible to observe the relationship between the increase of sound pressure level and the residual stress for dry and lubricated conditions.

Caracterização de um compósito utilizando cimento com agregado de resíduo plástico e resíduo de gesso

The demand for environmental comfort in construction systems within the insulation and thermal comfort, plus the advent of new laws regulating the minimum requirements of comfort, disposal of solid industrial waste, construction waste, the requirements of consumers by adopting construction methods "cleaner", encouraged the development of this work. Aims technologically characterize the composite proposed in three types of samples (10%, 30% and 50% of thermoset plastic industrial waste) and raw materials: gypsum waste, cement and plastic thermosetting industrial waste in order to produce the composite with properties of thermal insulation: conductivity, thermal diffusivity, specific heat and resistivity. The physical, structural and morphological properties of the raw materials were investigated by thermogravimetry analysis (TG / DSC), X-ray diffraction (DRX), X-ray fluorescence (FXR) and scanning electron microscopy (MEV). Obtaining mechanical properties through the compression strength test. The analysis results indicate characteristics suitable for cement matrix composite production with the addition of thermosetting plastic industrial waste and gypsum waste, with potential application of these materials in composites with properties of thermal insulation. Finally, assessing what proportion showed up with better performance. Considering the analysis and testing carried out.

Caracterização de um compósito utilizando cimento com agregado de resíduo plástico e resíduo de gesso

The demand for environmental comfort in construction systems within the insulation and thermal comfort, plus the advent of new laws regulating the minimum requirements of comfort, disposal of solid industrial waste, construction waste, the requirements of consumers by adopting construction methods "cleaner", encouraged the development of this work. Aims technologically characterize the composite proposed in three types of samples (10%, 30% and 50% of thermoset plastic industrial waste) and raw materials: gypsum waste, cement and plastic thermosetting industrial waste in order to produce the composite with properties of thermal insulation: conductivity, thermal diffusivity, specific heat and resistivity. The physical, structural and morphological properties of the raw materials were investigated by thermogravimetry analysis (TG / DSC), X-ray diffraction (DRX), X-ray fluorescence (FXR) and scanning electron microscopy (MEV). Obtaining mechanical properties through the compression strength test. The analysis results indicate characteristics suitable for cement matrix composite production with the addition of thermosetting plastic industrial waste and gypsum waste, with potential application of these materials in composites with properties of thermal insulation. Finally, assessing what proportion showed up with better performance. Considering the analysis and testing carried out.

Análise de falhas em rolamentos por análise de vibração aplicado a aerogeradores

With the heavy use of bearings in various segments of the industry, there are a large number of necessary interruptions in industrial processes to perform maintenance on these devices, with the case study wind turbines. The growth of the wind energy sector, encouraged to conduct research that helps to solve this problem. To contribute to predictive maintenance has been carried out a signal analysis using techniques which allow detection and location of the problem in order to prevent accidents caused and losses due to unexpected equipment failures, whereas low system rotation complicates the detection of the failure. To work around this problem, there was the indication of standard signals for defects in the bearings, making diagnosis of possible failures. With this diagnosis can be performed predictive maintenance, identifying the failure of the system that were tested, such as the introduction of grains of sand in the bearing, wear on the outer race of the bearing and bearing rust. By processing signals it is possible to construct graphs developing a mapping of defects by different peaks in the frequency band.

Uma interface para o controle de robôs móveis por intermédio de gestos

The main objective of this work was to enable the recognition of human gestures through the development of a computer program. The program created captures the gestures executed by the user through a camera attached to the computer and sends it to the robot command referring to the gesture. They were interpreted in total ve gestures made by human hand. The software (developed in C ++) widely used the computer vision concepts and open source library OpenCV that directly impact the overall e ciency of the control of mobile robots. The computer vision concepts take into account the use of lters to smooth/blur the image noise reduction, color space to better suit the developer's desktop as well as useful information for manipulating digital images. The OpenCV library was essential in creating the project because it was possible to use various functions/procedures for complete control lters, image borders, image area, the geometric center of borders, exchange of color spaces, convex hull and convexity defect, plus all the necessary means for the characterization of imaged features. During the development of the software was the appearance of several problems, as false positives (noise), underperforming the insertion of various lters with sizes oversized masks, as well as problems arising from the choice of color space for processing human skin tones. However, after the development of seven versions of the control software, it was possible to minimize the occurrence of false positives due to a better use of lters combined with a well-dimensioned mask size (tested at run time) all associated with a programming logic that has been perfected over the construction of the seven versions. After all the development is managed software that met the established requirements. After the completion of the control software, it was observed that the overall e ectiveness of the various programs, highlighting in particular the V programs: 84.75 %, with VI: 93.00 % and VII with: 94.67 % showed that the nal program performed well in interpreting gestures, proving that it was possible the mobile robot control through human gestures without the need for external accessories to give it a better mobility and cost savings for maintain such a system. The great merit of the program was to assist capacity in demystifying the man set/machine therefore uses an easy and intuitive interface for control of mobile robots. Another important feature observed is that to control the mobile robot is not necessary to be close to the same, as to control the equipment is necessary to receive only the address that the Robotino passes to the program via network or Wi-Fi.

Formulação de pasta de cimento flexível utilizando planejamento experimental

Steam injection is an oil recovery method accomplished by introducing steam directly into the oil well to the reservoir. The steam causes dilation of the casing, which, after reduction in temperature, tends to return to the initial dimensions: causing the formation of cracks in the cement and loss of hydraulic isolation.. In this context, the type of the SBR latex is used to improve the flexibility of the cement matrix by reducing the amount of fatigue failure. To prevent these failures, the mechanical resistance parameters should be carefully adjusted to well conditions. This work aims to study the mechanical behavior of cement slurry systems additivated with SBR latex for cementing oil wells subject to steam injection. Through the central composite factorial design was studied the behavior of the compressive strength by varying the density of the paste between 1.75 g /cm³ (14.6 lb/ Gal) and 1.89 g/cm³ (15,8lb / Gal), curing time between 4 days and 28 days and concentration of SBR Latex between 0 L / m³ and 534.722 L / m³ (0 gpc and 4 gpc). The results showed that increasing the concentration of SBR latex, within the given ranges, there was a decreased compression resistance and elastic modulus by increasing the elastic deformability of the slurry. From the results it can determine best slurries formulation conditions in oil well cementing operations subject to steam injection.

Formulação de pasta de cimento flexível utilizando planejamento experimental

Steam injection is an oil recovery method accomplished by introducing steam directly into the oil well to the reservoir. The steam causes dilation of the casing, which, after reduction in temperature, tends to return to the initial dimensions: causing the formation of cracks in the cement and loss of hydraulic isolation.. In this context, the type of the SBR latex is used to improve the flexibility of the cement matrix by reducing the amount of fatigue failure. To prevent these failures, the mechanical resistance parameters should be carefully adjusted to well conditions. This work aims to study the mechanical behavior of cement slurry systems additivated with SBR latex for cementing oil wells subject to steam injection. Through the central composite factorial design was studied the behavior of the compressive strength by varying the density of the paste between 1.75 g /cm³ (14.6 lb/ Gal) and 1.89 g/cm³ (15,8lb / Gal), curing time between 4 days and 28 days and concentration of SBR Latex between 0 L / m³ and 534.722 L / m³ (0 gpc and 4 gpc). The results showed that increasing the concentration of SBR latex, within the given ranges, there was a decreased compression resistance and elastic modulus by increasing the elastic deformability of the slurry. From the results it can determine best slurries formulation conditions in oil well cementing operations subject to steam injection.

O Litoral e a metrópole dinâmica imobiliária, turismo e expansão urbana na região metropolitana de Natal-RN

The metropolitan regions of Northeast Brazil are being gradually included in a scenario of international investments, which are motivated by the restructuring of both touristic and real-estate sectors. The new capital, real-estate developers and space configurations that result from this process indicate the need for the creation and implementation of public tools which should, at least, allow the mitigation of the urban impacts and environmental losses resulting from this situation. The effects on landscape and on the socio-spatial configuration result from the intensification caused by the dynamism of the "real estate-tourism" sector. There is a regional integration as an expression of the urban expansion of the metropolitan area of Natal. This study investigates the uniqueness of the restructuring and territorial integration of coastal areas and the strategies of the circuit of capital accumulation formed by linking the real estate to tourism. It is intended to increase the understanding about the strategies of tourism, real estate and public policy agents involved in this territorial reconfiguration and in the fund-raising needed for the investments, to understand the existing social and environmental effects and their future trends and also to understand the forms of spatial production as results from the practices of approaching the land transformation and the tourism valorization of the landscape, in a synchronous manner, first in the Northeast region and, as a focal study, in the Metropolitan Area of Natal. Likewise, it is intended to apprehend the current processes of metropolization of the eastern coast of Rio Grande do Norte, in addition to indicate its physical-territorial transformation and the types of projects/developments promoted by the market in the recent period. Based upon analysis undertaken for the Metropolitan Region of Natal RN, this piece of work presents some considerations on possible legal instruments that can be adjusted to the municipalities which are experiencing the impact of this peculiar and recent phenomenon in the region, caused by the arrival of the real estate-touristic capital. It is also intended to point out basic proposals to the forms of public intervention, in a speculative way, starting from a Metropolitan Planning project within a medium and long term

Atração e retenção de talentos em empresas de engenharia consultiva no setor de petróleo e gás natural da cidade de Natal

This study addresses the question of attraction and retention of talent in companies that produce engineering projects in the area of oil and natural gas in the city of Natal. The objectives were to identify the mechanisms that these companies use to attract and retain talented professionals and what the relationship between these practices and performance of these organizations in the market. This is a case study of a qualitative nature which were included in the fullness of companies that work in that class in the capital Potiguar. Have been applied to the managers of these companies structured questionnaires with eleven issues orientativas based on theoretical reference adopted. The research finds that managers understand the word "talent", recognize the importance of the appreciation of its employees and the development of their innate abilities to better organizational performance, much due to the fact they are acting in a market of fierce competition. His companies - though not submit the formal procedures related to the subject in question - have mechanisms that can be characterized as the attraction and retention of talent. The relationships identified in this study are consistent with the results found in other studies and put the information here can serve as the basis for that other managers, including other areas, to reach excellence in their respective industries

Contra as Secas: a engenharia e as origens de um planejamento regional no nordeste brasileiro

Droughts surfaced in 1877 as a crucial problem for the birthing Brazilian nation. Engineers, who formed the country's technical and scientific elite, took it upon themselves to study, understand and fight the problem through planned actions of intervention on space. This work, based on proposals and discussions contained in engineering magazines and reports, aims to provide elements for the comprehension of how these systematized actions against droughts, in the Iate nineteenth and early twentieth century, contributed to spatial analysis and the formation of a (then-inexistent) regional and territorial planning discipline in Brazi!. Engineers, by taking up the position of masterminds in the country's modernization, guaranteed for themselves personal economic stability, social prestige and political power. By understanding nature, either as a resource to be exploited or an adversary to national progress, they contributed to the delimitation of the region now known as the Northeast. By seeking to understand the drought phenomenon, they created knowledge about the space they sought to intervene on; by constructing their projects amid political and economical difficulty, they changed the organizational structures of cities and country in the northeast. The proposals for açudes (Iarge water reservoirs) allowed the fixation of population and the resistance against droughts; the roads - railroads and automotive roadways - connected the sertão to the capitais and the coast, speeding up help to the affected populations during droughts and allowing the circulation of goods so as to strengthen the local economies in normal rimes. The adopted practices and techniques, adapted from foreign experience and developed through trial and improvement, were consolidated as an eminently spatial intervention course, even if a theoretical body of regional or territorial planning wasn't formed in Brazil. Regional Planning proper was first applied in the country in the Northeast itself, in the 1950s, based off an economical view of reality in order to achieve development. The engineer's work prior tothat date, however, cannot be dlsconsldered. It was proved that, despite facing financial and political hurdles, engineers had a profound commitment to the problem and intended to act systematically to transform the economical and social relations in the region, in order to be victorious in their struggle against droughts

Análise comparativa de modelos de maturidade em gerenciamento de projetos: uma contribuição ao estudo da maturidade organizacional em setores de engenharia

The purpose of this dissertation is to formulate guidelines for the improvement of maturity models, or the development of new ones, aiming at its application to project departments. The maturity of project management has become critical for organizations that develop projects and want to stand out in the market they serve. For this purpose, maturity models provide paths in order to guarantee that the institutionalization of project management is achieved in the best possible way. Generally, these models assess the organization, define its current situation in managing projects and propose steps to be performed in the search of more advanced levels of maturity. With the objective of contributing to the improvement of maturity models for specific cases, a bibliographical research was conducted for the preparation of a comparative analysis matrix and performed a case study for application of two maturity models (MMGP and PMMM levels 2 and 3), selected based on criteria found in the literature, in an engineering department of an oil company. The case study supported the realization of a comparative analysis of models, from which guidelines were formulated for improvement. The results showed that thedepartment is evaluated in a medium stage of maturity, recording significant progress in some dimensions assessed. They also found that the results of applying the two models are presented as complementary, although the model is highlighted by the greater depth of MMGP diagnostic, considering many variables in their levels of maturity than model PMMM (levels 2 and 3).Finally, directions have been formulated that contribute to the improvement of maturity models, taking in account the organizational environment in which this work was developed

Egressos na avaliação da qualidade de um curso: o caso da Engenharia de Produção da UFRN

This thesis aims at analyzing the perspective of graduates perceived quality of an undergraduate course in order to contribute to continuous improvement. In order to achieve the proposed objectives, we performed a literature search, seeking together the work surrounding this issue, with the intent to update the concepts discussed today on the subject studied, they are: quality management, quality in higher education institutions and the system national assessment of higher education - Sinaes. The methodology is characterized as a case study, quantitative, and the object of study is composed of students who graduated from Production Engineering, Federal University of Rio Grande do Norte, which includes students who graduated from 2002 to 2010; data collection was done through the survey instrument, questionnaire, available online through SurveyMonkey interface, data analysis was done by means of descriptive statistics and multivariate analysis, including factor analysis. The proposed survey instrument consists of questions nineteen and twenty statements that address the central theme of this dissertation. The results show the identification of four latent factors (obtained by exploratory factor analysis), through two perspectives, the analysis of perception and importance, the results were similar in terms of the variable factors. The first factor was related to the support given to students, a factor known to support two extra class, the third factor related aspects of the library, and finalizing the evaluation and approached a factor of 4 facilities. Through research it was concluded that this study presents several points to be improved by the management team, and recommended to continue to evaluate the perceptions of graduates, seeking continuous improvement in service delivery by the university

Práticas pedagógicas das escolas de ensino médio que contribuem para a escolha do aluno pelo curso de Engenharia de Produção da UFRN

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior