Reciclagem de material asfáltico fresado utilizando solventes e microemulsões

With the increase of asphalt milling services was also a significant increase in recycling services pavements. The techniques used today are basically physical processes in which the milled material is incorporated into new asphalt mixtures or executed on site, with the addition of virgin asphalt and rejuvenating agent. In this paper seeks to analyze the efficiency of extraction of CAP (Petroleum Asphalt Cement) mixtures from asphalt milling, using commercial solvents and microemulsions. The solvents were evaluated for their ability to solubilize asphalt using an extractor reflux-type apparatus. Pseudoternary diagrams were developed for the preparation of microemulsion O/W surfactant using a low-cost coconut oil saponified (OCS). Microemulsions were used to extract the CAP of asphalt through physicochemical process cold. Analysis was performed concentration of CAP in solution by spectroscopy. The data provided in the analysis of concentration by the absorbance of the solution as the basis for calculating the percentage of extraction and the mass flow of the CAP in the solution. The results showed that microemulsions prepared with low concentration of kerosene and butanol/OCS binary has high extraction power of CAP and its efficiency was higher than pure kerosene, reaching 95% rate of extraction

Obtenção de emulsões asfálticas convencionais e modificadas com argilas e nanoargilas

The increasing demand for asphalt leads to the development of techniques that can improve the quality of products and increase the useful working life of pavements. Consequently, there is a growing application of asphalt emulsions, which are produced from a mixture of petroleum asphalt cement (CAP) with an aqueous phase. The main advantage of asphalt emulsions is its cold application, reducing energy costs. Conventional emulsions are obtained using asphalt, water, solvent, and additives. The modified asphalt emulsion is developed by adding a modifying agent to conventional emulsions. These modifiers can be natural fibers, waste polymers, nanomaterials. In this work modified asphalt emulsion were obtained using organoclays. First, it was prepared a conventional asphalt emulsion with the following mass proportion: 50% of 50/70 penetration grade CAP, 0.6% of additives and 3% of emulsifier, 20% of solvent and 26.4% of water. It was used bentonite and vermiculite (1% and 4%) to obtain the modified asphalt emulsion. Bentonite and vermiculite were added in its raw state and as an organoclay form and as an organoclay-acid form, resulting in 26 experimental runs. The methodology described by Qian et al. (2011), with modifications, was used to obtain the organoclay and the organoclay-acid form. infrared spectroscopy (IR)) were used to characterize the clays and nanoclays. The emulsions were prepared in a colloidal mill, using 30 minutes and 1 hour as mixing time. After, the emulsions were characterized. The following tests were performed, in accordance with the Brazilian specifications (DNER- 369/97): sieve analysis, Saybolt Furol viscosity, pH determination, density, settlement and storage stability, residue by evaporation, and penetration of residue. Finally, it can be concluded that the use of nanoclays as asphalt modifiers represent a viable alternative to the road paving industry

Extração supercrítica do óleo de linhaça: construção do extrator, estudo de parâmetros de processo, avaliação química e antioxidante do produto

The aim of the present study was to extract vegetable oil from brown linseed (Linum usitatissimum L.), determine fatty acid levels, the antioxidant capacity of the extracted oil and perform a rapid economic assessment of the SFE process in the manufacture of oil. The experiments were conducted in a test bench extractor capable of operating with carbon dioxide and co-solvents, obeying 23 factorial planning with central point in triplicate, and having process yield as response variable and pressure, temperature and percentage of cosolvent as independent variables. The yield (mass of extracted oil/mass of raw material used) ranged from 2.2% to 28.8%, with the best results obtained at 250 bar and 50ºC, using 5% (v/v) ethanol co-solvent. The influence of the variables on extraction kinetics and on the composition of the linseed oil obtained was investigated. The extraction kinetic curves obtained were based on different mathematical models available in the literature. The Martínez et al. (2003) model and the Simple Single Plate (SSP) model discussed by Gaspar et al. (2003) represented the experimental data with the lowest mean square errors (MSE). A manufacturing cost of US$17.85/kgoil was estimated for the production of linseed oil using TECANALYSIS software and the Rosa and Meireles method (2005). To establish comparisons with SFE, conventional extraction tests were conducted with a Soxhlet device using petroleum ether. These tests obtained mean yields of 35.2% for an extraction time of 5h. All the oil samples were sterilized and characterized in terms of their composition in fatty acids (FA) using gas chromatography. The main fatty acids detected were: palmitic (C16:0), stearic (C18:0), oleic (C18:1), linoleic (C18:2n-6) and α-linolenic (C18:3n-3). The FA contents obtained with Soxhlet dif ered from those obtained with SFE, with higher percentages of saturated and monounsaturated FA with the Soxhlet technique using petroleum ether. With respect to α-linolenic content (main component of linseed oil) in the samples, SFE performed better than Soxhlet extraction, obtaining percentages between 51.18% and 52.71%, whereas with Soxhlet extraction it was 47.84%. The antioxidant activity of the oil was assessed in the β-carotene/linoleic acid system. The percentages of inhibition of the oxidative process reached 22.11% for the SFE oil, but only 6.09% for commercial oil (cold pressing), suggesting that the SFE technique better preserves the phenolic compounds present in the seed, which are likely responsible for the antioxidant nature of the oil. In vitro tests with the sample displaying the best antioxidant response were conducted in rat liver homogenate to investigate the inhibition of spontaneous lipid peroxidation or autooxidation of biological tissue. Linseed oil proved to be more efficient than fish oil (used as standard) in decreasing lipid peroxidation in the liver tissue of Wistar rats, yielding similar results to those obtained with the use of BHT (synthetic antioxidant). Inhibitory capacity may be explained by the presence of phenolic compounds with antioxidant activity in the linseed oil. The results obtained indicate the need for more detailed studies, given the importance of linseed oil as one of the greatest sources of ω3 among vegetable oils

Obtenção de emulsões asfálticas modificadas utilizando resíduos industriais

The main objective of this research was the development and characterization of conventional and modified cationic asphalt emulsions. The asphalt emulsions were developed by using the Petroleum Asphalt Cement (CAP 50-70) from Fazenda Belém (Petrobras -Aracati-Ce). The first step in this research was the development of the oil phase (asphalt + solvent) and the aqueous phase (water + emulsifying agent + acid + additives), separately. During the experiments for the obtaining of the conventional asphalt emulsion, the concentration of each constituent was evaluated. For the obtaining of the oil phase, kerosene was used as solvent at 15 and 20 wt.%. For the development of the aqueous phase, the emulsifying agent was used at 0.3 and 3.0 wt.%, whereas the acid and the additive were set at 0.3 wt.%. The percentage of asphalt in the asphalt emulsion was varied in 50, 55, and 60 wt.% and the heating temperature was set at 120 °C. The aqueous phase in the asphalt emulsion was varied from 16.4 to 34.1 wt.% and the heating temperature was set at 60 °C. After the obtaining of the oil and the aqueous phases, they were added at a colloidal mill, remaining under constant stirring and heating during 15 minutes. Each asphalt emulsion was evaluated considering: sieve analysis, Saybolt Furol viscosity, pH determination, settlement and storage stability, residue by evaporation, and penetration of residue. After the characterization of conventional emulsions, it was chosen the one that presented all properties in accordance with Brazilian specifications (DNER-EM 369/97). This emulsion was used for the development of all modified asphalt emulsions. Three polymeric industrial residues were used as modifier agents: one from a clothing button industry (cutouts of clothing buttons) and two from a footwear industry (cutouts of sandals and tennis shoes soles), all industries located at Rio Grande do Norte State (Brazil).The polymeric residues were added into the asphalt emulsion (1 to 6 wt.%) and the same characterization rehearsals were accomplished. After characterization, it were developed the cold-mix asphalts. It was used the Marshall mix design. For cold-mix asphalt using the conventional emulsion, it was used 5, 6 and 7 wt.% asphalt emulsion. The conventional mixtures presented stability values according Brazilian specification (DNER-369/97). For mixtures containing asphalt modified emulsions, it was observed that the best results were obtained with emulsions modified by button residue

A doença de criar passarinhos: a lírica humanizadora de João Cabral de Melo Neto

João Cabral de Melo Neto n a jamais aimé les vers sentimentaux et prolixes venus de la tradition romantique. C est pour ça que son uvre a un discours objectif, rigoureusement elaboré e elle comporte certaines influences concretistes ça explique pourquoi l auteur est connu comme l ingénieur de la langage. En verité, le poète même dissait qu il était un homme froid et rationnel. La critique a assidument analysé la matière logique et le rigeuer formel de l uvre de Cabral de Melo. Pourtant, dans ce travail nous analysons les poèmes dont le sentiments humaines sont la mtière principal de l élaboration de l experiènce esthétique. La poèsie de João Cabral n est pas simple verbalisme formel, ni un uvre sens vie, car les objects concrètes et la langage objectif n empêchent pas qui le sujet décrit avec émotion les scènes presents dans les poèmes. Nous travaillons avec la hypothèse de que le poète a une attitude trop humaine quand il parle de l experience culturel et de l experience de la vie dans le Nord-est brésilien. Les unités témathiques de ce travail, pourtant, montrent la représentation du Nord-est dans la poèsie de João Cabral et examinent aussi le sentiment qu il sent par la memoire culturel de sa région. Parmi les aspects qui composent sa lyrique humaine nous citons la personification constant de les paysages du Nord-est le poète ne veux pas faire une décrition tophographique de la région parce que les places ont un valeuer sentimentel pour lui; au moyen d un discours erotique, Cabral represente les desirs et les intints humaines de sa terre; ensuite, il semble que le poète est enchanté et enveloppé avec certains elemets culturels de sa région, come l hamac, la littérature oral et la musique régional; la preoccupation avec la population explorée et la denonciation de la condition miserable dans le Nord-est brésilien confirment aussi la humanité présent dans son uvre; finalment, la récordation de l enfance et la nostalgie du temps passé sont, pour le poète, un possibilité qui peut aider dans la formation humaine de la population

Caracterização de resíduo sólido formado em biodiesel de sebo bovino

Biodiesel production has increased over the last decade because of the benefits associated with this fuel, including renewability, domestic feedstock, lower toxicity, and biodegradability. From 2008, the use of beef tallow as a feedstock for biodiesel production in Brazil has increased in significance, representing the second largest source of biodiesel, after soybeans. However, the performance of biodiesel in cold weather conditions is worse than diesel because of deposition of insoluble at low temperatures, accelerating the plugging of fuel filters and injectors of the vehicle engine. Studies have been conducted on beef tallow biodiesel, mostly related to the properties of thermal and oxidative stability. However, few studies have described the nature of the precipitate formed and its influence on product quality. Research suggests that the cause of deposition is related to the nature of saturated esters and monoacylglycerols as inducing agents. This study monitored the levels of mono-, diand triacylglycerols, the oxidation stability and the cold filter plugging point (CFPP) in beef tallow biodiesel samples from two commercial producers in Brazil for a period of twelve months. Filtered precipitates were analyzed by comparative techniques of GCFID, HPLC-UV/VIS, HPLC-MS-IT-TOF and TG to verify the nature, using monopalmitin and monostearin as reference standards. The formation of precipitate reduced the levels of monoacylglycerols in the beef tallow biodiesel. GC-FID and LCMS- IT-TOF results confirmed the nature of the deposit as saturated monoacylglycerols, predominantly monostearin and monopalmitin as the second major component. Moreover the TG analysis of the residue indicated similar thermal decomposition of the reference standards. The precipitate did not affect the oxidation stability of beef tallow biodiesel and the CFPP characteristic of blends up B60. However, the presence of iron reduced significantly the oxidation stability of biodiesel

Caracterização de resíduo sólido formado em biodiesel de sebo bovino

Biodiesel production has increased over the last decade because of the benefits associated with this fuel, including renewability, domestic feedstock, lower toxicity, and biodegradability. From 2008, the use of beef tallow as a feedstock for biodiesel production in Brazil has increased in significance, representing the second largest source of biodiesel, after soybeans. However, the performance of biodiesel in cold weather conditions is worse than diesel because of deposition of insoluble at low temperatures, accelerating the plugging of fuel filters and injectors of the vehicle engine. Studies have been conducted on beef tallow biodiesel, mostly related to the properties of thermal and oxidative stability. However, few studies have described the nature of the precipitate formed and its influence on product quality. Research suggests that the cause of deposition is related to the nature of saturated esters and monoacylglycerols as inducing agents. This study monitored the levels of mono-, diand triacylglycerols, the oxidation stability and the cold filter plugging point (CFPP) in beef tallow biodiesel samples from two commercial producers in Brazil for a period of twelve months. Filtered precipitates were analyzed by comparative techniques of GCFID, HPLC-UV/VIS, HPLC-MS-IT-TOF and TG to verify the nature, using monopalmitin and monostearin as reference standards. The formation of precipitate reduced the levels of monoacylglycerols in the beef tallow biodiesel. GC-FID and LCMS- IT-TOF results confirmed the nature of the deposit as saturated monoacylglycerols, predominantly monostearin and monopalmitin as the second major component. Moreover the TG analysis of the residue indicated similar thermal decomposition of the reference standards. The precipitate did not affect the oxidation stability of beef tallow biodiesel and the CFPP characteristic of blends up B60. However, the presence of iron reduced significantly the oxidation stability of biodiesel

Arcabouço geofísico, isostasia e causas do magmatismo cenozóico da província Borborema e de sua margem continental (Nordeste do Brasil)

The Borborema Province (BP) is a geologic domain located in Northeastern Brazil. The BP is limited at the south by the São Francisco craton, at the west by the Parnaíba basin, and both at the north and east by coastal sedimentary basins. Nonetheless the BP surface geology is well known, several key aspects of its evolution are still open, notably: i)its tectonic compartmentalization established after the Brasiliano orogenesis, ii) the architecture of its cretaceous continental margin, iii) the elastic properties of its lithosphere, and iv) the causes of magmatism and uplifting which occurred in the Cenozoic. In this thesis, a regional coverage of geophysical data (elevation, gravity, magnetic, geoid height, and surface wave global tomography) were integrated with surface geologic information aiming to attain a better understanding of the above questions. In the Riacho do Pontal belt and in the western sector of the Sergipano belt, the neoproterozoic suture of the collision of the Sul domain of the BP with the Sanfranciscana plate (SFP) is correlated with an expressive dipolar gravity anomaly. The positive lobule of this anomaly is due to the BP lower continental crust uplifting whilst the negative lobule is due to the supracrustal nappes overthrusting the SFP. In the eastern sector of the Sergipano belt, this dipolar gravity anomaly does not exist. However the suture still can be identified at the southern sector of the Marancó complex arc, alongside of the Porto da Folha shear zone, where the SFP N-S geophysical alignments are truncated. The boundary associated to the collision of the Ceará domain of the BP with the West African craton is also correlated with a dipolar gravity anomaly. The positive lobule of this anomaly coincides with the Sobral-Pedro II shear zone whilst the negative lobule is associated with the Santa Quitéria magmatic arc. Judging by their geophysical signatures, the major BP internal boundaries are: i)the western sector of the Pernambuco shear zone and the eastern continuation of this shear zone as the Congo shear zone, ii) the Patos shear zone, and iii) the Jaguaribe shear zone and its southwestern continuation as the Tatajuba shear zone. These boundaries divide the BP in five tectonic domains in the geophysical criteria: Sul, Transversal, Rio Grande do Norte, Ceará, and Médio Coreaú. The Sul domain is characterized by geophysical signatures associated with the BP and SFP collision. The fact that Congo shear zone is now proposed as part of the Transversal domain boundary implies an important change in the original definition of this domain. The Rio Grande do Norte domain presents a highly magnetized crust resulted from the superposition of precambrian and phanerozoic events. The Ceará domain is divided by the Senador Pompeu shear zone in two subdomains: the eastern one corresponds to the Orós-Jaguaribe belt and the western one to the Ceará-Central subdomain. The latter subdomain exhibits a positive ENE-W SW gravity anomaly which was associated to a crustal discontinuity. This discontinuity would have acted as a rampart against to the N-S Brasiliano orogenic nappes. The Médio Coreaú domain also presents a dipolar gravity anomaly. Its positive lobule is due to granulitic rocks whereas the negative one is caused by supracrustal rocks. The boundary between Médio Coreaú and Ceará domains can be traced below the Parnaíba basin sediments by its geophysical signature. The joint analysis of free air anomalies, free air admittances, and effective elastic thickness estimates (Te) revealed that the Brazilian East and Equatorial continental margins have quite different elastic properties. In the first one 10 km < Te < 20 km whereas in the second one Te ≤ 10 km. The weakness of the Equatorial margin lithosphere was caused by the cenozoic magmatism. The BP continental margin presents segmentations; some of them have inheritance from precambrian structures and domains. The segmentations conform markedly with some sedimentary basin features which are below described from south to north. The limit between Sergipe and Alagoas subbasins coincides with the suture between BP and SFP. Te estimates indicates concordantly that in Sergipe subbasin Te is around 20 km while Alagoas subbasin has Te around 10 km, thus revealing that the lithosphere in the Sergipe subbasin has a greater rigidity than the lithosphere in the Alagoas subbasin. Additionally inside the crust beneath Sergipe subbasin occurs a very dense body (underplating or crustal heritage?) which is not present in the crust beneath Alagoas subbasin. The continental margin of the Pernambuco basin (15 < Te < 25 km) presents a very distinct free air edge effect displaying two anomalies. This fact indicates the existence in the Pernambuco plateau of a relatively thick crust. In the Paraíba basin the free air edge effect is quite uniform, Te ≈ 15 km, and the lower crust is abnormally dense probably due to its alteration by a magmatic underplating in the Cenozoic. The Potiguar basin segmentation in three parts was corroborated by the Te estimates: in the Potiguar rift Te ≅ 5 km, in the Aracati platform Te ≅ 25 km, and in the Touros platform Te ≅ 10 km. The observed weakness of the lithosphere in the Potiguar rift segment is due to the high heat flux while the relatively high strength of the lithosphere in the Touros platform may be due to the existence of an archaean crust. The Ceará basin, in the region of Mundaú and Icaraí subbasins, presents a quite uniform free air edge effect and Te ranges from 10 to 15 km. The analysis of the Bouguer admittance revealed that isostasy in BP can be explained with an isostatic model where combined surface and buried loadings are present. The estimated ratio of the buried loading relative to the surface loading is equal to 15. In addition, the lower crust in BP is abnormally dense. These affirmations are particularly adequate to the northern portion of BP where adherence of the observed data to the isostatic model is quite good. Using the same above described isostatic model to calculate the coherence function, it was obtained that a single Te estimate for the entire BP must be lower than 60 km; in addition, the BP north portion has Te around 20 km. Using the conventional elastic flexural model to isostasy, an inversion of crust thickness was performed. It was identified two regions in BP where the crust is thickened: one below the Borborema plateau (associated to an uplifting in the Cenozoic) and the other one in the Ceará domain beneath the Santa Quitéria magmatic arc (a residue associated to the Brasiliano orogenesis). On the other hand, along the Cariri-Potiguar trend, the crust is thinned due to an aborted rifting in the Cretaceous. Based on the interpretation of free air anomalies, it was inferred the existence of a large magmatism in the oceanic crust surrounding the BP, in contrast with the incipient magmatism in the continent as shown by surface geology. In BP a quite important positive geoid anomaly exists. This anomaly is spatially correlated with the Borborema plateau and the Macaú-Queimadas volcanic lineament. The integrated interpretation of geoid height anomaly data, global shear velocity model, and geologic data allow to propose that and Edge Driven Convection (EDC) may have caused the Cenozoic magmatism. The EDC is an instability that presumably occurs at the boundary between thick stable lithosphere and oceanic thin lithosphere. In the BP lithosphere, the EDC mechanism would have dragged the cold lithospheric mantle into the hot asthenospheric mantle thus causing a positive density contrast that would have generated the main component of the geoid height anomaly. In addition, the compatibility of the gravity data with the isostatic model, where combined surface and buried loadings are present, together with the temporal correlation between the Cenozoic magmatism and the Borborema plateau uplifting allow to propose that this uplifting would have been caused by the buoyancy effect of a crustal root generated by a magmatic underplating in the Cenozoic

Estudo do comportamento da sinterização de compactos de cavacos de um aço SAE 1050 obtidos sob alta pressão

From an economic standpoint, the powder metallurgy (P/M) is a technique widely used for the production of small parts. It is possible, through the P/M and prior comminution of solid waste such as ferrous chips, produce highly dense sintered parts and of interest to the automotive, electronics and aerospace industries. However, without prior comminution the chip, the production of bodies with a density equal to theoretical density by conventional sintering techniques require the use of additives or significantly higher temperatures than 1250ºC. An alternative route to the production of sintered bodies with high density compaction from ferrous chips (≤ 850 microns) and solid phase sintering is a compression technique under high pressure (HP). In this work, different compaction pressures to produce a sintered chip of SAE 1050 carbon steel were used. Specifically, the objective was to investigate them, the effect of high pressure compression in the behavior of densification of the sintered samples. Therefore, samples of the chips from the SAE 1050 carbon steel were uniaxially cold compacted at 500 and 2000 MPa, respectively. The green compacts obtained were sintered under carbon atmosphere at 1100 and 1200°C for 90 minutes. The heating rate used was 20°C/min. The starting materials and the sintered bodies were characterized by optical microscopy, SEM, XRD, density measurements (geometric: mass/volume, and pycnometry) and microhardness measurements Vickers and Rockwell hardness. The results showed that the compact produced under 2000 MPa presented relative density values between 93% and 100% of theoretical density and microhardness between 150 HV and 180 HV, respectively. In contrast, compressed under 500 MPa showed a very heterogeneous microstructure, density value below 80% of theoretical density and structural conditions of inadequate specimens for carrying out the hardness and microhardness measurements. The results indicate that use of the high pressure of ferrous chips compression is a promising route to improve the sinterability conditions of this type of material, because in addition to promoting greater compression of the starting material, the external tension acts together with surface tension, functioning as the motive power for sintering process. Additionally, extremely high pressures allow plastic deformation of the material, providing an intimate and extended contact of the particles and eliminating cracks and pores. This tends to reduce the time and / or temperature required for good sintering, avoiding excessive grain growth without the use of additives. Moreover, higher pressures lead to fracture the grains in fragile or ductile materials highly hardened, which provides a starting powder for sintering, thinner, without the risk of contamination present when previous methods are used comminution of the powder.

Avaliação da suplementação de vitamina E sobre a concentração de alfa-tocoferol no leite materno em mulheres com partos prematuros

The term vitamin E refers to a group of eight molecular compounds which differ in structure and bioavailability, and the RRR-alpha-tocopherol more biologically active form. The composition of vitamin E in breast milk undergoes variations during lactation, colostrum and milk richer in this micronutrient compared to transitional and mature milk. Newborns, especially premature infants are more susceptible to vitamin E deficiency and to prevent the damage caused by this deficiency has been proposed supplementation of neonates with this micronutrient, however, there is no consensus to carry out this intervention. Thus, maternal supplementation with RRRalpha-tocopherol in the postpartum period can be a good alternative to try to raise the alpha-tocopherol levels in breast milk and therefore provide the premature newborn adequate amounts of vitamin E. This study to evaluate the effect of supplementation with 400 UI acetate RRR-alpha-tocopherol in women with premature births, on the concentration of alpha-tocopherol in breast milk colostrum, transitional and mature. The study included 89 healthy adult women were enrolled in the control group (n = 51) and supplemented group (n = 38). Blood samples were collected and milk colostrum soon after birth (0h milk) twenty-four hours, new rate of colostrum milk was collected (24h milk). The transitional and mature milk were collected in seven days (7d milk) and thirty days (30d milk) after delivery, respectively. Supplementation in the supplemented group was held after the collection of blood and 0h milk. The alpha-tocopherol analyzes were performed by high-performance liquid chromatography. Serum levels of alpha-tocopherol less than 516 μg/dL were considered indicative of nutritional deficiency. The average concentration of alphatocopherol in the serum of the control group mothers was 1159.8 ± 292.4 μg/dL and the supplemented group was 1128.3 ± 407.2 μg/dL (p = 0.281). All women had nutritional status in vitamin E suitable. In both groups, it was observed that the concentration of vitamin E in colostrum milk was higher compared to transitional and mature milk. In the supplemented group, the concentration of alpha-tocopherol in the milk increased 60 % after supplementation, from 1339.3 ± 414.2 μg/dL (0h milk) to 2234.7 ± 997.3 μg/dL (24h milk). While the control group values in colostrum 0h and colostrum 24h were similar (p = 0.681). In the control group the follow-on milk alphatocopherol value was 875.3 ± 292.4 μg/dL and in the group supplemented 1352.8 ± 542.3 μg/dL, an increase of 35% in the supplemented group compared to control (p <0.001). In mature milk alpha-tocopherol concentrations between the control group (426.6 ± 187.5 μg/dL) and supplemented (416.4 ± 214.2 μg/dL) were similar (p = 0.853). Only 24h milk supplemented group answered the nutritional requirement of alpha-tocopherol (4 mg/day) of the newborn. These results show that the transport of this micronutrient for milk occurs in a controlled and limited way. Thus, the native vitamin E supplementation increases the concentration of alpha-tocopherol in colostrum and milk and transition does not influence the concentration in mature milk. Only the increase in colostrum milk was sufficient to meet the nutritional requirement of premature newborns.

“Acham que brotamos das fontes dessa cidade?”: uma etnografia sobre o cotidiano de sobrevivência de pessoas em situação de rua em Nata/RN

Through participant observation, held in the administrative region east of Natal / RN, this research aimed to understand about the daily life of men and women living on the streets in the city. How they relate to the space where they live? In this relationship, which uses and survival strategies triggered by this social segment? These were some of the questions that guided this research, in order to highlight the specificities of this way of life and the possible consequences that such a situation could reverberate. In this sense, there was an effort to keep up with people on the streets, their itineraries and seize their narratives. Along the search path - which took place intermittently between the years 2011-2015 - attended spaces of occupation and traffic of this population group in the street, as well as insert me and got involved in events, forums, seminars, meetings and subject of joints on the streets as a political movement (MNPR / RN). They are considered in this study as people on the street to those who occupy the street as their main space of survival and ordering of daily life: in the streets sleep, feed themselves, meet the physiological and hygienic needs, and is where draw sustenance. The street is taken in this research in its broadest sense, including all possible places relatively protected from the cold, rain and exposure to violence, thus includes both open and public spaces: as squares and parks; but also closed and private places: hostels, abandoned warehouses, prisons, etc. It was observed that in none of these spaces guys on the street are established in a fixed manner, in contrast, they experience the roaming, which in part is due to urban systems - which tends to stigmatize them and delete them places - and the very need to survive, because while living in the street differentiated practices are triggered, and these differ from the dominant mode of sedentary life.

“Acham que brotamos das fontes dessa cidade?”: uma etnografia sobre o cotidiano de sobrevivência de pessoas em situação de rua em Nata/RN

Through participant observation, held in the administrative region east of Natal / RN, this research aimed to understand about the daily life of men and women living on the streets in the city. How they relate to the space where they live? In this relationship, which uses and survival strategies triggered by this social segment? These were some of the questions that guided this research, in order to highlight the specificities of this way of life and the possible consequences that such a situation could reverberate. In this sense, there was an effort to keep up with people on the streets, their itineraries and seize their narratives. Along the search path - which took place intermittently between the years 2011-2015 - attended spaces of occupation and traffic of this population group in the street, as well as insert me and got involved in events, forums, seminars, meetings and subject of joints on the streets as a political movement (MNPR / RN). They are considered in this study as people on the street to those who occupy the street as their main space of survival and ordering of daily life: in the streets sleep, feed themselves, meet the physiological and hygienic needs, and is where draw sustenance. The street is taken in this research in its broadest sense, including all possible places relatively protected from the cold, rain and exposure to violence, thus includes both open and public spaces: as squares and parks; but also closed and private places: hostels, abandoned warehouses, prisons, etc. It was observed that in none of these spaces guys on the street are established in a fixed manner, in contrast, they experience the roaming, which in part is due to urban systems - which tends to stigmatize them and delete them places - and the very need to survive, because while living in the street differentiated practices are triggered, and these differ from the dominant mode of sedentary life.

Testes para a avaliação da qualidade fisiológica de sementes de Moringa oleifera Lam

The evaluation of seed vigor is an important factor for detection of lots of high quality seeds, so that development of procedures to evaluate the physiological potential has been an important tool in quality control programs seeds. In this sense the study aimed to adapt the methodologies of accelerated aging, electrical conductivity and potassium leaching to evaluate Moringa oleifera seed vigor LAM.. Therefore, four lots of moringa seeds were subjected to the germination tests, seedling emergence, speed of emergence index, emergence first count, length and dry mass of seedlings and cold test for their physiological characterization, in addition to accelerated aging, electrical conductivity and potassium leaching. The experimental design was completely randomized with four replications of 50 seeds and the means compared by Tukey test at 5% probability. For accelerated aging the periods were studied aging 12, 24 and 72 hours at 40, 42 and 45°C. For the electrical conductivity test was used to a temperature of 25°C for periods of 4, 8, 12, 16 and 24 hours of immersion in 75 to 125 mL of distilled water, using 25 to 50 seeds, and for potassium leaching test samples were used 25 to 50 seeds, placed in plastic cups containing 70 and 100 mL of distilled water at 25°C for periods of 1, 2, 3, 4, 5 and 6 hours. From the results obtained, it can be inferred that the methods best fit for the accelerated aging test Moringa seeds were a temperature of 40°C for 12 to 72 hours, 42°C 72 hours 45°C 24 hours . In the electrical conductivity test Moringa seeds, the combination of 50 seeds in 75 mL distilled water for a period of immersion of 4 hours and 50 seeds in 125 mL of 4 hours were efficient for the differentiation of lots of Moringa seeds as to vigor and for potassium leaching test moringa seeds, the combination of 50 seeds in 100mL of distilled water allowed the separation of lots of four levels of vigor, at 2 hours of immersion, showing promise in evaluate the quality of moringa seeds.

Testes para a avaliação da qualidade fisiológica de sementes de Moringa oleifera Lam

The evaluation of seed vigor is an important factor for detection of lots of high quality seeds, so that development of procedures to evaluate the physiological potential has been an important tool in quality control programs seeds. In this sense the study aimed to adapt the methodologies of accelerated aging, electrical conductivity and potassium leaching to evaluate Moringa oleifera seed vigor LAM.. Therefore, four lots of moringa seeds were subjected to the germination tests, seedling emergence, speed of emergence index, emergence first count, length and dry mass of seedlings and cold test for their physiological characterization, in addition to accelerated aging, electrical conductivity and potassium leaching. The experimental design was completely randomized with four replications of 50 seeds and the means compared by Tukey test at 5% probability. For accelerated aging the periods were studied aging 12, 24 and 72 hours at 40, 42 and 45°C. For the electrical conductivity test was used to a temperature of 25°C for periods of 4, 8, 12, 16 and 24 hours of immersion in 75 to 125 mL of distilled water, using 25 to 50 seeds, and for potassium leaching test samples were used 25 to 50 seeds, placed in plastic cups containing 70 and 100 mL of distilled water at 25°C for periods of 1, 2, 3, 4, 5 and 6 hours. From the results obtained, it can be inferred that the methods best fit for the accelerated aging test Moringa seeds were a temperature of 40°C for 12 to 72 hours, 42°C 72 hours 45°C 24 hours . In the electrical conductivity test Moringa seeds, the combination of 50 seeds in 75 mL distilled water for a period of immersion of 4 hours and 50 seeds in 125 mL of 4 hours were efficient for the differentiation of lots of Moringa seeds as to vigor and for potassium leaching test moringa seeds, the combination of 50 seeds in 100mL of distilled water allowed the separation of lots of four levels of vigor, at 2 hours of immersion, showing promise in evaluate the quality of moringa seeds.

Determinação de recomendações bioclimáticas para habitação de interesse social de quatro climas do Rio Grande do Norte

Recomendações projetuais baseadas no clima são fontes importantes de diretrizes para os arquitetos. Uma das formas de obtenção dessas recomendações é por meio de normas, como a NBR 15220 (ABNT, 2005), que agrupa as cidades em zonas homogêneas quanto as estratégias sugeridas. O zoneamento bioclimático brasileiro divide o território do Rio Grande do Norte em duas zonas, a ZB 7 e ZB 8, que possuem algumas recomendações distintas, como aberturas grandes e vedações leves para a região litorânea contra aberturas pequenas e vedações pesadas para a região semiárida. Entretanto, outras configurações climáticas estão presentes no RN e não possuem clara recomendação. Este é o caso das regiões serranas e das regiões intermediárias entre o litoral e a região semiárida. Em virtude disso, este estudo visa encontrar recomendações bioclimáticas para habitações de interesse social nessas quatro condições climáticas. Para tanto, utilizou-se ferramenta computacional para realização de simulações das condições térmicas de três tipos de habitações populares - alongada, ramificada e compacta - e das seguintes estratégias: presença ou ausência de ventilação natural e sombreamento, massa térmica leve ou pesada, e Fator de Calor Solar alto ou baixo. Essas simulações foram realizadas para quatro condições climáticas do estado. Foram analisados os desempenhos de cada caso para identificar as estratégias e tipos de habitação recomendados para cada clima. De maneira geral, nos climas deNatal, Mossoró e Caicó viu-se que habitações com FCS baixo e com presença de ventilação natural possuem os melhores desempenhos. No clima de Areia, a ausência de ventilação aliada ao baixo FCS é que produziu os melhores desempenhos. O sombreamento melhora o desempenho nas cidades de clima quente, mas aumenta as horas com desconforto ao frio em Areia. A massa térmica varia de acordo com as demais estratégias, tendo casos em que habitações com massa térmica alta possuem melhores desempenhos que outros casos com massa térmica baixa. Por fim, viu-se que as estratégias para Natal, Caicó e Mossoró são bem semelhantes, com a recomendação de ventilação natural, FCS baixo nas vedações e sombreamento. Para Areia, a recomendação é não ventilar, ter FCS baixo e massa térmica alta.