Análise das emissões gasosas de um veículo flex funcionando com diferentes combustíveis

Efforts in research and development of new technologies to reduce emission levels of pollutant gases in the atmosphere has intensified in the last decades. In this context, it can be highlighted the modern systems of electronic engine management, new automotive catalysts and the use of renewable fuels which contributes to reduce the environmental impact. The purpose of this study was a comparative analysis of gas emissions from a automotive vehicle, operating with different fuels: natural gas, AEHC or gasoline. To execute the experimental tests, a flex vehicle was installed on a chassis dynamometer equipped with a gas analyzer and other complementary accessories according to the standard guidelines of emission and security procedures. Tests were performed according to NBR 6601 and NBR 7024, which define the urban and road driving cycle, respectively. Besides the analysis of exhaust gases in the discharge tube, before and after the catalyst, using the suction probe of the gas analyzer to simulate the vehicle in urban and road traffic, were performed tests of fuel characterization. Final results were conclusive in indicating leaded gasoline as the fuel which most contributed with pollutant emissions in atmosphere and the usual gasoline being the fuel which less contributed with pollutant emissions in atmosphere

Bioecologia da ictiofauna marinha descartada pelo arrasto camaroeiro em praias da Bacia Potiguar, Brasil

The composition of ichthyofauna discarded by trawling shrimping, their reproductive status and feeding ecology were studied on the beaches of Basin Rio Grande do Norte, Brazil. Fish were collected monthly in the year of 2012. During biometrics, portions of the digestive tract and of gonads were removed, fixed in formalin 10% and Bouin, respectively, for be submitted to histological processing by the techniques of hematoxylin-eosin. Stomach content analyzes were performed using the methods of Frequency of Occurrence and Volumetric and was calculated the repletion index. Throughout the study period were recorded a total of 49 species. The fish assemblages differed between sections monitoring, with the highest abundance, biomass and indices of richness and diversity in sections B, D and C. Already the excerpt A, showed higher values for dominance and equitability. In the cluster analysis according to the faunal similarity was observed the formation of three groups: group I formed by excerpts B and D, group II by excerpt C and group III formed by excerpt A. The assessment of reproductive stage revealed that the fish assemblages discarded by trawling are composed mainly of juveniles. Regarding the feeding ecology, the species Larimus breviceps, Menticirrhus littoralis and Pomadasys corvinaeformis characterized as carnivorous with tendency to carcinofagia. Already Conodon nobilis characterized as carnivorous with tendency to piscivory, but all proved generalist-opportunistic with increase of feeding activity during drought. The dendrogram of grouping of the species developed based on the food items used shows the formation of four groups: Group I consists of species that feed mainly of "gastropod" and "sediment"; group II of "teleost fish"; the group III of "crustacea" and group IV of "echinodermata" and "bivalve". The anatomical and histological characteristics of the digestive tract were consistent with the dietary habits of the analyzed species. In this context, the Costa Branca of Rio Grande do Norte can be considered a feeding site and recruitment for juveniles, which, opportunistically, utilize resources associated with the background

Desenvolvimento de Sistemas Microparticulados Superparamagnéticos Gastro-resistentes para Diagnóstico e Terapêutica

This work aimed to develop a suitable magnetic system for administration by the oral route. In addition to that, it was intended to review the current uses of magnetic systems and the safety related to magnetic field exposure. Methods: Coprecipitation and emulsification/crosslinking were carried out in order to synthesize magnetite particles and to coat them, respectively. Results: According to literature review, it was found that magnetic particles present several properties such as magnetophoresis in magnetic field gradient, production of a surrounding magnetic field, and heat generation in alternated magnetic field. When the human organism is exposed to magnetic fields, several interaction mechanisms come into play. However, biological tissues present low magnetic susceptibility. As a result, the effects are not so remarkable. Concerning the development of a magnetic system for oral route, uncoated magnetite particles did undergo significant dissolution at gastric pH. On the other hand, such process was inhibited in the xylan-coated particles. Conclusions: Due to their different properties, magnetic systems have been widely used in biosciences. However, the consequent increased human exposure to magnetic fields has been considered relatively safe. Concerning the experimental work, it was developed a polymer-coated magnetic system. It may be very promising for administration by the oral route for therapy and diagnostic applications as dissolution at gastric pH hardly took place

Identificação e fatores de virulência de Candida spp isoladas da cavidade bucal de transplantados renais do hospital universitário Onofre Lopes em Natal-RN

Despite Candida species are often human commensals isolated from various oral sites such as: tongue, cheek and palatal mucosa plus subgingival region, there are some properties linked to the organism commonly known as virulence factors which confer them the ability to produce disease. Oral candidiasis is one of the main oral manifestations reported in literature related to kidney transplant patients. The objectives of the present study were to identify and investigate virulence factors of yeasts isolated from the oral cavity of kidney transplant recipients admitted at the Hospital Universitário Onofre Lopes, in Natal RN. Seventy Candida species isolated from 111 kidney transplant recipients were investigated in this study. Identification of the isolates was performed by using the evidence of germ tube formation, hypertonic broth, tolerance to grow at 42°C, micromorphology and biochemical profiles. We observed a high rate of isolation of yeasts from the oral cavity of kidney transplant recipients (63.1%) being C. albicans was the most prevalent species. Oral candidiasis was diagnosed in 14.4% of transplant recipients. We evaluated virulence properties of the isolates regarding to: biofilm formation on polystyrene microplates as well as XTT reduction, adherence to acrylic resin and human buccal epithelial cells and proteinase activity. Most isolates were able to form biofilm by the method of adhesion to polystyrene. All isolates of Candida spp. remained viable during biofilm formation when analyzed by the method of XTT reduction. The number of CFU attached to the acrylic resin suggested high adherence for C. parapsilosis. C. albicans isolates showed higher median adherence to human buccal epithelial cells than non-C. albicans Candida isolates. Nevertheless, this difference was not statistically significant. C. dubliniensis showed low ability to adhere to plastic and epithelial cells and biofilm formation. Proteolytic activity was observed for all the isolates investigated, including the unique isolate of C. dubliniensis. There was a statistically significant association between proteinase production and the presence of oral candidiasis. Studies related to oral candidiasis in renal transplant recipients are limited to clinical and epidemiological data, but investigations concerning Candida spp. virulence factor for this group of individuals are still scarce. We emphasize the importance of studies related to virulence factors of yeasts isolated from this population to contribute to the knowledge of microbiological aspects of oral candidiasis

Avaliação da expressão das moléculas HLA de classe I não clássicas HLA-G E HLA-E em espécimes gástricas de pacientes acometidos com a bactéria Helicobacter Pylori

The expression of human leukocyte antigen G (HLA-G) and human leukocyte antigen E (HLA-E) in physiological and pathological processes remains unknown, it is believed that these molecules play a fundamental role in the establishment and maintenance of immune tolerance by inhibiting the functions of immunocompetent cells. In literature we found no published study involving the bacterium Helicobacter pylori (H. pylori) with expression of HLA-G and HLA-E. The objective this study is investigated the expression of this protein in gastric biopsies of patients with the bacterium H. pylori. Sixty-four biopsies of the patients with diagnosis of infection by H. pylori were evaluated to expression of HLA-G and HLA-E. The samples were stratified according to the presence of carcinoma or peptic ulcers. Patients without H. pylori were used to control. To investigate the expression of this protein were used immunohistochemistry technique with monoclonal antibody anti-HLA-G and anti-HLA-E. Other criteria such as analysis of the inflammatory infiltrate (hematoxylin-eosin) and identification of H. pylori (Giemsa) were analyzed. We detected HLA-G and HLA-E molecules in the most samples containing ulcer and gastric carcinoma. In negative control group was not detected the presence of HLA-G and HLA-E. The presence of H. pylori seems modulate the expression of HLA-G and HLA-E, favoring the evolution of infection, giving different degrees of gastric lesion in epithelium of these patients

Estudo dos genes do complexo do antígeno leucocitário humano (hla) associados à susceptibilidade ao diabetes mellitus tipo 1

Of all of the genes associated with the development of Diabetes mellitus type 1 (T1D), the largest contribution comes from the genes in the Human Leukocyte Antigen (HLA) region, mostly the class II DR e DQ genes. Specific combinations of alleles DRB1, DQA1 and DQB1 constituting haplotypes, and further, a combination of more than one haplotype, providing multilocus genotypes are associated with susceptibility, protection and neutrality to DM1. Thus, the aim of present study was to verified the association of polymorphisms of HLA genes class II with susceptibility to type 1 diabetes mellitus (T1D). Ninety-two patients with T1D and 100 individuals normoglycemics (NG) aged between 6 and 20 years were studied. Genomic DNA was obtained from peripheral whole blood, collected in EDTA tube, using the extraction kit Illustra Triple Prep®, GE Healthcare. For HLA typing was used DNA LABType system by One Lambda kit applying Luminex® technology to the method of PCRSSO typing reverse. The alleles DRB1*03:01, *04:05, *04:01, *04:02, DQA1*03:01g, *05:01g, DQB1*02:01g, *03:02, the haplotypes DRB1*03:01-DQA1*05:01-DQB1*02:01, DRB1*04:05-DQA1*03:01g-DQB1*03:02, DRB1*04:02-DQA1*03:01g-DQB1*03:02, DRB1*04:01-DQA1*03:01g-DQB1*03:02 and DR3-DQ2/DR4-DQ8 genotype were significantly associated with the chance of developing T1D. The alleles DRB1*11:01, *15:03, *15:01, *13:01, DQA1*01:02, *04:01g, *01:03, DQB1*06:02, *03:01g, *06:03, *04:02, the haplotypes DRB1*11:01-DQA1*05:01-DQB1*03:01, DRB1*13:01-DQA1*01:03-DQB1*06:03 and DRX-DQX/DRX-DQX genotype, formed by other than the DR3-DQ2 or DR4-DQ8 haplotypes, were significantly associated with T1D protection Despite the major racial Brazilian, even at the regional level, these results are similar to the majority of alleles, genotypes and haplotypes of HLA class II-related susceptibility or resistance to T1D, extensively described in the literature for Caucasian population. Children with age at diagnosis less than 5 years of age had significantly higher frequency of the heterozygous genotype DR3-DQ2/DR4-DQ8 compared to children with age at diagnosis than 5 years old. These results also demonstrate strong association of the genetic profile of the class II HLA for this age group, possibly associated with the severity and rapid progression to the onset of T1D. The knowledge of HLA class II genes may be useful in genetic screens that allow the prediction of T1D

Uma intervenção educativa para profissionais de saúde na prevenção de pneumonia associada à ventilação mecânica

Quasi-experimental study, prospective with quantitative approach, performed at the Hospital do Coração in Natal, aimed at verified the existence of difference between the care given by health professionals to the patients under mechanical ventilation (MV) in the Intensive Care Unit, before and after an educative intervention. The population was of 31 professionals, with data collected between november 05 of 2007 to march 27 of 2008. The results show a yong population, female gender, middle level of education, nursing technique, working between 05 and 09 years on nursing profession, and 01 to 04 years on Intensive Care Unit; almost all, never had an kind of training over prevent pneumonia associated to mechanical ventilation; from those that had training, occur on the work place with duration from 12 to 24 hours. About endotracheal intubation, the cuff was tested with a sterilized syringe had a positive change after a educative intervention, increased from 75,0% to 100,0%; the sterile guide was used on 75,0% before and 100,0% after an educative intervention. Regarding endotracheal suction procedure, was not informed to the patient on 72,7% before, however was informed on 56,7% after; the hands was not previously washed 68,5% before, however was 63,3% after the procedure; mask was used on 74,2 % opportunities before and 76,7% after; the aspiration catheter had adequated size on 98,9% observation before and 100,0% after; the gaze was sterilized on 95,7% before and 100,0% after; the ventilator was connected to the patient during the aspiration intervals on 94,4% observation before and 100,0% after; the ambu bag was clean and protected on 76,1% before and 85,7% after; the aspiration catheter was discarded after be used on 98,9% before and 100,0% after; FIO2 was turned to the begging value on 32,9% observation before and 12,0% after; before the procedure 71,9% professions washed their hands and 73,3% after; before, notes of aspiration results were performed on 70,8% observation and 86,7% after. Regarding devices used on respiratory tract, aspirator flasks were not swapped on 84,6% observations before and 71,0% after; daily látex extention change was not performed on 93,6% observation before and 87,1% after; the ambu bag change was not performed on 50,0% observation before even if was duty or unprotected and on 75,8% opportunities was changed, after; nebulization was not prepared with sterile fluids or manipulated aseptically on 65,2% observation before, perhaps was on 71,7% after; before nebulizers were not changed on 65,2% observations, perhaps were on 60,9% after. Concerning ventilator breathing circuits, condense fluids cumulated on circuits were removed on 55,0% opportunities before, and 64,0% after; moisturizer was not filled with sterile water when already had small amount of liquid inside on 78,4% observations before, and 90,2% after; MV circuits were changed on 97,0% observations on presence of visible duty or when presents some kind of failure, before and 98,4% after. About body position, on 51,3% observations the decubitus position change were done before and 78,2% after; fowler position was maitened on 95,5% observations before and 98,2% after; Regarding respiratory physiotherapy, enteral diet was not interrupted before respiratory physiotherapy on 94,9% before and 90,0% after; respiratory physiotherapy devices were not disinfected or sterile on 69,6% observations before but they re on 60,0% after; before the cateter was not tested before introduction enteral diet or medications on 100,0% but after was done on 15,2%. About enteral feeding, intestine motility and measure of stomach contents were not done on 100,0% observations before, but was 15,2% after. We conclude that 05 of 07 valuated procedures in relation to MV, had a significant improvement on quality of care given after educative intervention, when compared before intervention

Assistência de enfermagem e o risco para úlceras de pressão medido pela Escala de Braden em unidade de terapia intensiva

The problem facing the incidence of pressure ulcers (UP) in the hospital environment especially in the intensive care unit (ICU), although it is an old and frequent event in our professional practice, it is not notified in the researches as much as it should be. We observed a tendency to invest in therapeutical and in studies about the production of sophisticated new bandages. Few, however, are the investments in research on preventive measures in order to prevent or at least slow down the development of lesions. In this sense, the study aimed to analyze the correlation between nursing care and the risk of developing UP measured by the Braden scale in ICU patients. This is a descriptive study of longitudinal quantitative approach. The project obtained a favourable opinion from the Ethics Committee of HUOL (no 486/10). Data collection was carried out in the Hospital of Unimed in Natal during six months in 2011. The sample was of 32 patients hospitalized in ICU for over four days. The results were processed in SPSS 15.0 for descriptive statistics and inferential statistics. We identified that, only 9.4% of our sample developed UP, being predominantly male, elderly people aged above 60 years, Caucasian, with diagnostic hypothesis at the time of hospitalization of sepsis, were clinical patients, who presented hemodynamic instability, using orotracheal tube (TOT), enteral probe (SNE), vesical probe delay (SVD) and had values of albumin and hemoglobin levels below normal. In addition, these patients had a longer hospital stay, longer usage of TOT, SNE, SVD, increased use of sedation and drain than those who did not develop UP and were all at risk for developing these injuries second Braden scores. 66.7% of the lesions developed were located in the sacral region, limiting the degree I and all patients that developed were considered serious, 100.0% of them have evolved since the death. Small were the differences between the averages of Braden scores between patients with and without UP, 11,9+2,4 against 12,4+2,6 with p = 0.627. The clinical aspects of the patients in the study were instrumental in the development of UP, once, these findings were statistically significant through the Mann-Whitney test, and appropriateness of nursing conduct was decisive for the prevention of pressure ulcers in critical patients, since many were those classified as at risk (28) and few who have developed lesions (03)

Projeto, construção e levantamento de desempenho de um concentrador solar cilíndro parabólico com mecanismo automático de rastreamento solar

An cylinder-parabolic solar concentrator is presented to produce steam for different applications. This prototype was built in glass fiber with dimensions that follow a study of optimization of parameters inherent in the optical reflection of sunlight by the surface of reflection and absorption of the same by tubing that leads the fluid of work. The surface of the concentrator of 2.24 m² has been covered by layers of mirror with 1.0 m of lenght and 2.0 cm wide. The absorb tubing consists of a copper tube diameter equal to 28 mm. The concentrator is moving to follow the apparent motion of the sun. It will be presented the processes of manufacturing and assembly of the concentrator proposed, which has as main characteristics the facilities construction and assembly, in addition to reduced cost. Will be presented data from tests performed to produce steam setting up some parameters that diagnose the efficiency of the concentrator. It will be demonstrated the viabilities thermal, economic and of materials of the proposed system.The maximum temperature achieved in the vacuum tube absorber was 232.1°C and average temperature for 1 hour interval was 171.5°C, obtained in a test with automation. The maximum temperature achieved in the output of water was 197.7°C for a temperature of 200.0°C in the absorber tube. The best average result of the water exit temperature to interval of 1 hour was 170.2°C for a temperature of 171.2°C, in the absorber tube, obtained in test with automation. Water exit mean temperatures were always above of the water steaming temperature. The concentrator present a useful efficiency of 38% and a production cost of approximately R$ 450,00 ( $ 160.34)

Fibras de sisal (Agave sisalana) como isolante térmico de tubulações

In the last decades there was a significant increasing of the numbers of researchers that joint efforts to find alternatives to improve the development of low environmental impact technology. Materials based on renewable resources have enormous potentials of applications and are seen as alternatives for the sustainable development. Within other parameters, the sustainability depends on the energetic efficiency, which depends on the thermal insulation. Alternative materials, including vegetal fibers, can be applied to thermal insulation, where its first goal is to minimize the loss of energy. In the present research, it was experimentally analyzed the thermal behavior of fiber blankets of sisal (Agave sisalana) with and without surface treatment with oxide hidroxide (NaOH). Blankets with two densities (1100/1200 and 1300/1400 g/m2) were submitted to three rates of heat transfer (22.5 W, 40 W and 62.5 W). The analysis of the results allowed comparing the blankets treated and untreated in each situation. Others experiments were carried out to obtain the thermal conductivity (k), heat capacity (C) and the thermal diffusivity (α) of the blankets. Thermo gravimetric analyses were made to the verification of the thermal stability. Based on the results it was possible to relate qualitatively the effect of the heat transfer through the sisal blankets subjected to three heat transfer rates, corresponding to three temperature values (77 °C, 112 °C e 155 °C). To the first and second values of temperature it was verified a considerable reduction on the rate of heat transfer; nevertheless, to the third value of temperature, the surface of the blankets (treated and untreated) in contact with the heated surface of the tube were carbonized. It was also verified, through the analyses of the results of the measurements of k, C e α, that the blankets treated and untreated have values near to the conventional isolating materials, as glass wool and rock wool. It could be concluded that is technically possible the use of sisal blankets as constitutive material of thermal isolation systems in applications where the temperature do not reach values greater than 112 ºC

Efeito de adições poliméricas na aderência de pastas de cimento a tubos metálicos após ciclagem térmica

Thermal recovery methods, especially steam injection, have been used to produce heavy oils. However, these methods imply that the metallic casing-cement sheath interface is submitted to thermal cycling. As a consequence, cracking may develop due to the thermal expansion mismatch of such materials, which allows the flow of oil and gas through the cement sheath, with environmental and economical consequences. It is therefore important to anticipate interfacial discontinuities that may arise upon Thermal recovery. The present study reports a simple alternative method to measure the shear strength of casing-sheath interfaces using pushthrough geometry, applied to polymer-containing hardened cement slurries. Polyurethane and recycled tire rubber were added to Portland-bases slurries to improve the fracture energy of intrinsically brittle cement. Samples consisting of metallic casing sections surrounded by hardened polymer-cement composites were prepared and mechanically tested. The effect of thermal cycles was investigated to simulate temperature conditions encountered in steam injection recovery. The results showed that the addition of polyurethane significantly improved the shear strength of the casing-sheath interface. The strength values obtained adding 10% BWOC of polyurethane to a Portland-base slurry more than doubled with respect to that of polyurethane-free slurries. Therefore, the use of polyurethane significantly contributes to reduce the damage caused by thermal cycling to cement sheath, improving the safety conditions of oil wells and the recovery of heavy oils

Simulação computacional da interação fluido-estrutura em bombas de cavidades progressivas

The pumping through progressing cavities system has been more and more employed in the petroleum industry. This occurs because of its capacity of elevation of highly viscous oils or fluids with great concentration of sand or other solid particles. A Progressing Cavity Pump (PCP) consists, basically, of a rotor - a metallic device similar to an eccentric screw, and a stator - a steel tube internally covered by a double helix, which may be rigid or deformable/elastomeric. In general, it is submitted to a combination of well pressure with the pressure generated by the pumping process itself. In elastomeric PCPs, this combined effort compresses the stator and generates, or enlarges, the clearance existing between the rotor and the stator, thus reducing the closing effect between their cavities. Such opening of the sealing region produces what is known as fluid slip or slippage, reducing the efficiency of the PCP pumping system. Therefore, this research aims to develop a transient three-dimensional computational model that, based on single-lobe PCP kinematics, is able to simulate the fluid-structure interaction that occurs in the interior of metallic and elastomeric PCPs. The main goal is to evaluate the dynamic characteristics of PCP s efficiency based on detailed and instantaneous information of velocity, pressure and deformation fields in their interior. To reach these goals (development and use of the model), it was also necessary the development of a methodology for generation of dynamic, mobile and deformable, computational meshes representing fluid and structural regions of a PCP. This additional intermediary step has been characterized as the biggest challenge for the elaboration and running of the computational model due to the complex kinematic and critical geometry of this type of pump (different helix angles between rotor and stator as well as large length scale aspect ratios). The processes of dynamic generation of meshes and of simultaneous evaluation of the deformations suffered by the elastomer are fulfilled through subroutines written in Fortan 90 language that dynamically interact with the CFX/ANSYS fluid dynamic software. Since a structural elastic linear model is employed to evaluate elastomer deformations, it is not necessary to use any CAE package for structural analysis. However, an initial proposal for dynamic simulation using hyperelastic models through ANSYS software is also presented in this research. Validation of the results produced with the present methodology (mesh generation, flow simulation in metallic PCPs and simulation of fluid-structure interaction in elastomeric PCPs) is obtained through comparison with experimental results reported by the literature. It is expected that the development and application of such a computational model may provide better details of the dynamics of the flow within metallic and elastomeric PCPs, so that better control systems may be implemented in the artificial elevation area by PCP

Desenvolvimento de um protótipo para alimentação de pós para aspersão térmica em tocha de plasma

The nanometric powders have special features that usually result in new properties, originating applications or expanding them in various fields of knowledge. Because having a high area/volume ratio, phenomena such as superficial strength of adsorption becomes greater than the weight of the powder which makes more difficult its handling. The high power of agglomeration of these powders requires study and development of equipments to enable its management into the plasma torch. The objective of this work is to develop a powder feeder which can solve the mainly problems about insertion of powder into the thermal spray developed in the laboratory of plasmas, which are carried out with plasma torch arc not transferred (plasma spray). Therefore, it was made a aluminum s powder feeder and tests were performed to verify their operation and determine its rate of deposition by spraying powders of niobium pentoxide (Nb2O5) and titanium dioxide (TiO2) with particle sizes less than 250 mesh (<0.063 mm). We used masses of 0.5 g - 1.0 g and 1.5 g of each powder in tests lasting 15 seconds - 20 to 25 seconds for each mass. The tests were performed in two ways: at atmospheric pressure using argon gas with a flow of 9 l / min as carrier gas and through a Venturi pipe also using argon gas with a flow of 9 l / min as carrier gas and with a flow of 20 l/min as the feed gas passing through the Venturi pipe. The powder feeder developed in this paper is very easy to be handling and building, resulting in feeding rate of 0.25 cm3/min - 1.37 cm3/min. The TiO2 showed higher feeding rates than the Nb2O5 in all tests, and the best rates were obtained with tests using mass 1.5 g and time of 15 seconds, reaching feeding rate of 1.37 cm3/min. The flow of feed had low interference in feeding rate during the tests

Estudo de um isolante térmico para tubos fabricado em material compósito

It presents a new type of insulation for ductwork hot water, which can be used in solar systems for heating water, which consists of a composite of different compositions based on plaster, cement and EPS ground, palm and water. This composite has as its main features easy assembly and manufacturing processes and low cost. Comparative results will be presented on the tests of materials and thermal tubes proposed. Four formulations were used to manufacture tubes with three diameters 70, 65 and 42mm. It was also tested conventionally used for elastomeric foam insulation to 110 ° C, for a comparative analysis with the composite pipe insulator proposed. It will demonstrate that the cost of manufacturing of such tubes is competitive with alternative elastomeric foam tested, but results of the composite tube to the temperature range studied, are lower. Another drawback of the composite insulator tube is its large mass. It would be important to test such a composite for greater levels of temperature to a diagnostic technique competitive with conventionally used insulators. A positive factor of using the proposed composite-tube would be the recycling of EPS so damaging to the environment, representing an environmentally friendly application of science

Desenho e Construção de um protótipo gerador de jato de plasma frio a pressão atmosférica para aplicações biomédicas

Research for better performance materials in biomedical applications are constants. Thus recent studies aimed at the development of new techniques for modification of surfaces. The low pressure plasma has been highlighted for its versatility and for being environmentally friendly, achieving good results in the modification of physic chemical properties of materials. However, it is requires an expensive vacuum system and cannot able to generate superficial changes in specific regions. Furthermore, it is limits their use in polymeric materials and sensitive terms due to high process temperatures. Therefore, new techniques capable of generating cold plasma at atmospheric pressure (APPJ) were created. In order to perform surface treatments on biomaterials in specific regions was built a prototype capable of generating a cold plasma jet. The prototype plasma generator consists of a high voltage source, a support arm, sample port and a nozzle through which the ionized argon. The device was formed to a dielectric tube and two electrodes. This work was varied some parameters such as position between electrodes, voltage and electrical frequency to verify the behavior of glow discharges. The disc of titanium was polished and there was a surface modification. The power consumed, length, intensity and surface modifications of titanium were analyzed. The energy consumed during the discharges was observed by the Lissajous figure method. To check the length of the jets was realized with Image Pro Plus software. The modifications of the titanium surfaces were observed by optical microscopy (OM ) and atomic force microscopy (AFM ). The study showed that variations of the parameters such as voltage, frequency and geometric position between the electrodes influence the formation of the plasma jet. It was concluded that the plasma jet near room temperature and atmospheric pressure was able to cause modifications in titanium surface