Integração dos processos de flotação e foto-fenton para redução de óleos e graxas de água produzida em campos de petróleo

During production of oil and gas, there is also the production of an aqueous effluent called produced water. This byproduct has in its composition salts, organic compounds, gases and heavy metals. This research aimed to evaluate the integration of processes Induced Air Flotation (IAF) and photo-Fenton for reducing the Total Oils and Greases (TOG) present in produced water. Experiments were performed with synthetic wastewater prepared from the dispersion of crude oil in saline solution. The system was stirred for 25 min at 33,000 rpm and then allowed to stand for 50 min to allow free oil separation. The initial oil concentration in synthetic wastewater was 300 ppm and 35 ppm for the flotation and the photo-Fenton steps, respectively. These values of initial oil concentration were established based on average values of primary processing units in Potiguar Basin. The processes were studied individually and then the integration was performed considering the best experimental conditions found in each individual step. The separation by flotation showed high removal rate of oil with first-order kinetic behavior. The flotation kinetics was dependent on both the concentration and the hydrophilic-lipophilic balance (HLB) of the surfactant. The best result was obtained for the concentration of 4.06.10-3 mM (k = 0.7719 min-1) of surfactant EO 2, which represents 86% of reduction in TOG after 4 min. For series of surfactants evaluated, the separation efficiency was found to be improved by the use of surfactants with low HLB. Regarding the TOG reduction step by photo-Fenton, the largest oil removal reached was 84% after 45 min of reaction, using 0.44 mM and 10 mM of ferrous ions and hydrogen peroxide, respectively. The best experimental conditions encountered in the integrated process was 10 min of flotation followed by 45 min of photo-Fenton with overall TOG reduction of 99%, which represents 5 ppm of TOG in the treated effluent. The integration of processes flotation and photo-Fenton proved to be highly effective in reducing TOG of produced water in oilfields

Essa marca de suor numa canção: o processo de redução estrutural na poesia de Zila Mamede

Die Beziehung zwischen Literatur und Gesellschaft wurden, im Laufe der Jahrhunderte, aus unterschiedlichen Perspektiven analysiert. Die Wissenschaftler analysieren manchmal die Aspekten der sozialen Realität, sie betonen manchmal die Natur der literarischen Werk. Wir glauben, dass Antonio Candido einen Gleichgewichtszustand erreicht, als er das Konzept der strukturellen Reduktion oder Formalisierung entwickelt. Nämlich, der Prozess, bei dem die menschliche und soziale Leben zu einem Bestandteil der literarischen Struktur wird. Der Autor tritt eine Einbahnstraße und er kann Daten aus der sozialen Ordnung aufholen, ohne dabei die Materialität des Textes den Augen verlieren. Und das sind die theoretische Annahmen, die die Entwicklung dieser Arbeit leiten. Wir wollen zu zeigen, dass die Struktur der mamediana Lyrik aufdeckt, signifikante Daten der Gesellschaft, in der der Autore eingefügt wurde enthüllt. Folglich, wir analysieren soziale Thema, das sein Werk durchzieht. Zuerst, wir untersuchen, wie Zila Mamede den Alltag der Gesellschaft vertreten. Von der strukturellen Organisation der Gedichte, wir erkennen, das die Episode aus kleiner Städte ein Akt des Widerstands gegen die fragmentierte Profil der kapitalistischen Gesellschaf sind. Das ist, warum sie doch eng mit der Idee der Tradition erscheinen. Die dichotome Beziehung zwischen den regionalen Daten und der Element der Modernisierung etabliert, sie wird durch die Organisation des Raumes verstärkt. Während die Stadt bei konkrete gesellschaftliche Ordnung Spitzenbeträge verweist, hat die Landschaft eine harmonische und warme Form. Allgemeinen, die moderne Stadt von Zila Mamede geformt, ist eine Abbild der Industriegesellschaft. Die Bilder die Landschaft sind ein Gegenmittel gegen die Feindseligkeiten Merkmale der neuen urbanen Zustand. So, die Landschaft hat die Funktion von Umstrukturierung der Persönlichkeit des Einzelnen durch die Erfahrung der großen Städte betroffen verdinglichenden. Der Konflikt, der durch das lyrische mamediana läuft, sind Reflexionen des Prozesses der Modernisierung der Stadt Natal, ihres eigenen Landes die politische Instabilität, sie durch verschiedene staatliche Programme ging, während Der Autor seine literarische Tätigkeit verfolgt

Padrões cariotípicos em tetraodontiformes (Osteichthypes) :redução genômica e mecanismos de diversificação

The Tetraodontiformes order is composed for about 400 species of fish, distributed in ten families, with circuntropical distribution. The morphologic diversity of each family reflects in, part, the different levels of specialization. This group represents an ancestry after-Perciformes and constitutes the last branch of the diffusion of the Teleósteos, occupying a position of prominence. The phylogenetics relationships of the Tetraodontiformes exist diverse works examining and, in all, these families are recognized as groups brothers, being Diodontidae next to Tetraodontidae and Balistidae next to Monacanthidae. Although it possesss a representative number of species, the works involving of the families Balistidae and Monacanthidae are few exemplary, especially species of oceanic islands. In this work cytogenetic studies in five species had been analyzed Cantherhines macrocerus, Cantherhines pullus (Monacanthidae), Melichthys niger (Balistidae), Sphoeroides testudíneus (Tetraodontidae) and Chilomycterus antennatus (Diodontidae); through conventional coloration, Ag-NORs and C banding. Ahead of the different karyological trends of evolution presented by the Tetraodontiformes, the present work also searched to verify the relation existence enters the total size of the chromosomes with the amount of DNA in these groups of Tetraodontiformes. For such, they had been correlated the total size of the chromosomes of these species, with values of content of available DNA in literature. The cytogenetics analyses for the species C.macrocerusJ C.pullus (Monacanthidae) and M.niger (Balistidae), had disclosed 40 chromosomes, all acrocentrics. All possess only one pair of NORs and pericentromeric heterochromatin. For S.testudíneus the found dyploid number was equal 2n=46, with NF=78 (16m+18sm+8st+4a), while that for C.antennatus it possesss 2n=50, with NF=76 (4m+22st+24a). Both species possess simple NORs and pericentromeric heterochromatin blocks. In M.niger, the presence of positive marking (heterochromatin and NOR) in the secondary constriction in the second chromosomic pair suggesting the occurrence of a rearrangement, possibly a fusing involving these homologous ones, indicating that these events had been important for the establishment of the karyological history of this group. A maintenance of the chromosomic constancy found in the populations of C.macrocerus (Monacanthidae) and S.testudineus (Tetraodontidae) perhaps if must for the aiding of the gene flow through oceanic chains. These data contrast with the differentiated kinds of chromosomes of C.antennatus between the Northeast coast and Southeastern, suggesting that the ecological standards of each species, added to the conditions of the marine environment, can be responsible for the karyological delineation of each species. The found characteristics for the species C.macrocerus, C.pullus, M.niger, S.testudineus and C.antennatus add it the available data for other species of Tetraodontiformes. From the data gotten in the present study, it can be inferred that the DNA content possesss direct relation with the total length of the chromosomes

A redução de danos no atendimento especializado em álcool e outras drogas

The harm reduction HR is the official policy of Ministry of Public Health to deal with problem derived from alcohol consumption and other drugs AD. The HR refers to policies and support programs whose purpose is to reduce the risks related to the use of AD, without necessarily decrease individual consumption. This research aim was to analyze the HR conceptions and practices at two specialized institutions for AD users: 1) Psychosocial Care Center Alcohol and Drugs III (CAPSad III); 2) Therapeutic Community Fazenda da Esperança (FE) Dom Bosco. This is a qualitative research that used the following methodological tools: semi-structured interview with 21 professionals; socio demographic file and rounds of conversation with 63 participants users; participant observation and field journal. The interviews with professionals have characterized HR as a less complex and cheap treatment. At FE the HR proposal does not make part of their actions, being considered ―against the human being dignity‖. At CAPSad III is understood as an ―inevitable‖ guideline to service, once users do not remain abstinent. The users understand RD as an improvement in healthy conditions, social relations and work that occurs with the decreasing consumption of AD. They use the HR when they avoid situations that facilitate AD consumption, share relapse prevention strategies and, exclusively at CAPSad III, decrease psychotropic consumption. Stands out as an analyzer the HR comprehension as a less efficient treatment that opposes to the objective of both institutions, which is abstinence. The HR is not operationalize in daily routine by professionals and users as a healthy promotion strategy, however, the users are more affected to HR and produce strategies to face the difficulties arising from the AD consumption

Uma máquina de redução de grafos para serviços web

Web services are software accessible via the Internet that provide functionality to be used by applications. Today, it is natural to reuse third-party services to compose new services. This process of composition can occur in two styles, called orchestration and choreography. A choreography represents a collaboration between services which know their partners in the composition, to achieve the service s desired functionality. On the other hand, an orchestration have a central process (the orchestrator) that coordinates all application operations. Our work is placed in this latter context, by proposing an abstract model for running service orchestrations. For this purpose, a graph reduction machine will be defined for the implementation of service orchestrations specified in a variant of the PEWS composition language. Moreover, a prototype of this machine (in Java) is built as a proof of concept

Detecção e recuperação de falhas para a máquina de redução de grafos PEWS-AM

Web services are software units that allow access to one or more resources, supporting the deployment of business processes in the Web. They use well-defined interfaces, using web standard protocols, making possible the communication between entities implemented on different platforms. Due to these features, Web services can be integrated as services compositions to form more robust loose coupling applications. Web services are subject to failures, unwanted situations that may compromise the business process partially or completely. Failures can occur both in the design of compositions as in the execution of compositions. As a result, it is essential to create mechanisms to make the implementation of service compositions more robust and to treat failures. Specifically, we propose the support for fault recovery in service compositions described in PEWS language and executed on PEWS-AM, an graph reduction machine. To support recovery failure on PEWS-AM, we extend the PEWS language specification and adapted the rules of translation and reduction of graphs for this machine. These contributions were made both in the model of abstract machine as at the implementation level

Redução in situ de NIO durante a sinterização de misturas NI/NIO produzidas por metalurgia do pó

The nickel alloys are widely used in the production of various materials, especially those that require mechanical strength characteristics associated with resistance to corrosion, for example, the stainless steel. Another use is the production of nickel alloy sintered from powder of metallic nickel. A promising alternative for the production of sintered components of nickel with an important reduction in costs of starting material is the use of mixtures of powders of Ni-NiO. This work aimed to study in situ reduction of NiO during sintering mixtures of Ni / NiO produced by powder metallurgy. The nickel mixtures have been processed by the technique of powder metallurgy and were pre-sintered in an oven under plasma reducing atmosphere of hydrogen. Mixtures Ni +15%NiO, Ni +25%NiO and Ni +35%NiO were studied and compared with samples consisting only of metallic Ni. Dilatometric tests were performed to study the sintering conditions of the mixtures. The consolidated material was analyzed for their microstructure and microhardness. Dilatometry graphs showed that the addition of nickel oxide in all compositions the active sintering the mixtures studied. In tests of microhardness indentations were made at different points of the sample surface. All compositions showed microhardness values close to the consolidated material from metallic nickel. However, sample containing Ni+35% NiO, showed a large dispersion of the values of microhardness tests performed at different points of the sample surface. Microstructural analysis of the material showed a higher concentration of voids and the presence of oxides in the waste composition of the mixtures Ni 35% NiO. The samples containing Ni+15%NiO showed microstructural characteristics and mechanical properties similar to metallic nickel consolidated under the same conditions of the compositions studied in this work and therefore had great potential for production of sintered nickel alloys

Aplicação da destilação simulada por cromatografia gasosa e da termogravimetria para a avaliação da influência da redução do teor de enxofre sobre as propriedades físico-químicas do óleo diesel

One of the main problems related to the use of diesel as fuel is the presence of sulfur (S) which causes environmental pollution and corrosion of engines. In order to minimize the consequences of the release of this pollutant, Brazilian law established maximum sulfur content that diesel fuel may have. To meet these requirements, diesel with a maximum sulfur concentration equal to 10 mg/kg (S10) has been widely marketed in the country. However, the reduction of sulfur can lead to changes in the physicochemical properties of the fuel, which are essential for the performance of road vehicles. This work aims to identify the main changes in the physicochemical properties of diesel fuel and how they are related to reduction of sulfur content. Samples of diesel types S10, S500 and S1800 were tested according with the methods of the American Society for Testing and Materials (ASTM). The fuels were also characterized by thermogravimetric analysis (TG) and subjected to physical distillation (ASTM D86) and simulated distillation gas chromatography (ASTM D2887). The results showed that the reduction of sulfur turned the fuel lighter and fluid, allowing a greater applicability to low temperature environments and safer for transportation and storage. Through the simulated distillation data was observed that decreasing sulfur content resulted in higher initial boiling point temperatures and the decreasing of the boiling temperature of the medium and heavy fractions. Thermogravimetric analysis showed a loss event mass attributed to volatilization or distillation of light and medium hydrocarbons. Based on these data, the kinetic behavior of the samples was investigated and it was observed that the activation energies (Ea) did not show significant changes throughout conversion. Considering the average of these energies, the S1800 had the highest Ea during the conversion and the S10 the lowest values

Uma máquina de redução de grafos extensível para a implementação de fluxos de trabalho

Graph Reduction Machines, are a traditional technique for implementing functional programming languages. They allow to run programs by transforming graphs by the successive application of reduction rules. Web service composition enables the creation of new web services from existing ones. BPEL is a workflow-based language for creating web service compositions. It is also the industrial and academic standard for this kind of languages. As it is designed to compose web services, the use of BPEL in a scenario where multiple technologies need to be used is problematic: when operations other than web services need to be performed to implement the business logic of a company, part of the work is done on an ad hoc basis. To allow heterogeneous operations to be part of the same workflow, may help to improve the implementation of business processes in a principled way. This work uses a simple variation of the BPEL language for creating compositions containing not only web service operations but also big data tasks or user-defined operations. We define an extensible graph reduction machine that allows the evaluation of BPEL programs and implement this machine as proof of concept. We present some experimental results.

Projeto SB Brasil 2010 - pesquisa nacional de saúde bucal revela importante redução da cárie dentária no país

O Projeto SB Brasil 2010, planejado e executado por órgãos do SUS, nos âmbitos federal, estadual e municipal, e de universidades brasileiras, por meio de Centros Colaboradores do Ministério da Saúde se constitui em recurso de valor estratégico para aprofundar os conhecimentos sobre os agravos bucais no país, e dá contribuição inestimável para orientar os rumos da PNSB e avançar na construção de um modelo de atenção pautado na Vigilância à Saúde

Projeto SB Brasil 2010 - pesquisa nacional de saúde bucal revela importante redução da cárie dentária no país

O Projeto SB Brasil 2010, planejado e executado por órgãos do SUS, nos âmbitos federal, estadual e municipal, e de universidades brasileiras, por meio de Centros Colaboradores do Ministério da Saúde se constitui em recurso de valor estratégico para aprofundar os conhecimentos sobre os agravos bucais no país, e dá contribuição inestimável para orientar os rumos da PNSB e avançar na construção de um modelo de atenção pautado na Vigilância à Saúde

Estudo da redução de arrasto induzido por polímeros em escoamentos internos turbulentos em dutos

The flows turbulent and laminar are present in various applications of engineering and one of the villain of energy loss big is the surface friction. Currently, there are several research aimed for the study of reducing drag (DR) with the objective of developing effective methods to reduce the friction. Regardless of numerous research carried out until today, the phenomenon DR still remains in study not it is fully understood. This paper studied the drag reduction by polymer induction in turbulent internal flows in ducts. We constructed a testing bench to perform the analysis of drag reduction, the bench has basically two manometers with a 8.5 psi full scale, a peripheral pump 0.5 HP, an acrylic tank, valves and tubes pvc and is situated in the Laboratory Fluid Mechanics UFRN. Were used as polymer additives to polyethylene glycol 4000, the Polyox WSR N60K, Polyox WSR 301 and Polyox WSR 205. The rationale for the choice of these polymers is their wide application in situations requiring greater energy efficiency, such as the addition reducing polymers for the jet used by the fire department to achieve greater distances. The induced drag reduction polymers is investigated from the turbulent flow analysis, with Reynolds number in a range between 2×104

Estudo da redução de arrasto induzido por polímeros em escoamentos internos turbulentos em dutos

The flows turbulent and laminar are present in various applications of engineering and one of the villain of energy loss big is the surface friction. Currently, there are several research aimed for the study of reducing drag (DR) with the objective of developing effective methods to reduce the friction. Regardless of numerous research carried out until today, the phenomenon DR still remains in study not it is fully understood. This paper studied the drag reduction by polymer induction in turbulent internal flows in ducts. We constructed a testing bench to perform the analysis of drag reduction, the bench has basically two manometers with a 8.5 psi full scale, a peripheral pump 0.5 HP, an acrylic tank, valves and tubes pvc and is situated in the Laboratory Fluid Mechanics UFRN. Were used as polymer additives to polyethylene glycol 4000, the Polyox WSR N60K, Polyox WSR 301 and Polyox WSR 205. The rationale for the choice of these polymers is their wide application in situations requiring greater energy efficiency, such as the addition reducing polymers for the jet used by the fire department to achieve greater distances. The induced drag reduction polymers is investigated from the turbulent flow analysis, with Reynolds number in a range between 2×104

Utilização da macroalga Ulva lactuca linnaeus na redução de nutrientes (NH4+,NO3- e PO4-2) provenientes da carcinicultura

Dentre as macroalgas capazes de absorver altas concentrações de N e P dissolvidos na água, destaca-se a Chlorophyta Ulva lactuca, bastante adaptável e resistente às adversidades ambientais, como grandes variações de temperatura, salinidade, matéria orgânica e metais pesados. Trata-se também de uma espécie bastante comum nas áreas intertidais do litoral norte-riograndense. Devido a suas características ecológicas, fisiológicas e nutricionais, foi avaliado nesse estudo, o seu potencial como biofiltro na redução de NH4+, NO3- e PO4-2, tanto em condições controladas como também em um viveiro de camarão. No experimento laboratorial, foram utilizados quatro aquários de vidro de 30 x 20 x 20cm com 10L de água, sendo três aquários experimentais contendo 20g de U. lactuca e um controle. O acréscimo de biomassa foi de 2,92g (22,92 ± 6,29g; p < 0,05) em relação ao inóculo inicial de 20g, sob temperatura (28,50 ± 0,58ºC), salinidade (35,00 ± 0,00 ), pH (8,26 ± 0,02) e luz constante (250 μmol.m2s-1). O crescimento positivo (1,78 ± 4,38%dia-1; p < 0,05), juntamente com a alta eficiência de absorção de amônio (83%; p < 0,001), nitrato (83%; p < 0,001) e ortofosfato (53%; p < 0,001), demonstrou que, nessas condições, a Ulva lactuca absorveu os nutrientes e aumentou sua biomassa. Já no experimento de campo, realizado na fazenda TECNARÃO, situada no município de Arez/RN (06° 11 40 Latitude Sul, e 35º 09 37 Longitude Oeste), foram utilizadas três gaiolas de PVC, posicionadas a 12cm da superfície da água, cada uma com dimensões de aproximadamente 59 x 59 x 15cm, onde foram colocadas 200g de U. lactuca. O ganho de biomassa de 3g (203,00 ± 41,02g; p < 0,001) foi muito semelhante às condições controladas, demonstrando a adaptabilidade da espécie em condições ambientais variáveis, onde, apesar da temperatura pouco variável (27,45 ± 0,64ºC), houve progressiva diminuição de salinidade (25 - 15 ), devido ao período de fortes chuvas (34,70 ± 23,78mm). Somado a isso, foram observados vários fatores biológicos interferindo no viveiro, como a presença de epífitas, organismos endofíticos, fouling e a herbivoria por parte dos próprios camarões. Houve aumento nas concentrações de NH4+ (4,36 ± 1,69 μmol.L-1), NO3- (0,17 ± 0,25μmol.L-1) e PO4-2 (0,41 ± 0,13μmol.L-1), coincidindo com o crescimento da espécie até a terceira semana. Todos os parâmetros ambientais analisados, assim como a biomassa e a Taxa de Crescimento Relativo (TCR), obtidos no campo, apresentaram variações altamente significativas (p < 0,001). As correlações observadas entre biomasa e NH4+ (r = 0,82; p < 0,001) e entre biomassa e PO4-2 (r = 0,87; p < 0,001), indicam que esta espécie é capaz de ter um crescimento satisfatório nas condições eutróficas de um viveiro de camarão, sendo possível seu uso como biofiltro.

Estudo sobre a redução aluminotérmica de Ta2O5 e TiO2 usando descarga de cátodo oco

In this study it was used two metallic oxides, Ta2O5 and TiO2, in order to obtain metallic powders of Ta and Ti through aluminothermic reduction ignited by plasma. Ta2O5 and TiO2 powders were mixed with Al in a planetary mill, using different milling times. A thermal analysis study (DTA and TG) was carried out, in order to know the temperature to react both the mixtures. Then, these mixtures were submitted to a hollow cathode discharge, where they were reacted using aluminothermic reduction ignited by plasma. The product obtained was characterized by XRD and SEM, where it was proven the possibility of producing these metallic particles, different from the conventional process, where metallic ingots are obtained. It was verified that the aluminothermic reduction ignited by plasma is able to produce metallic powders of Ta and Ti, and a higher efficiency was observed to the process with Ta2O5-Al mixtures. Among different microstructural aspects observed, it can be noted the presence of metallic nanoparticles trapped into an Al2O3 matrix, besides acicular structures (titanium) and dendritic structures (tantalum), which are a product characteristic from a fast cooling