Desempenho de argamassas produzidas com agregados reciclados oriundos do resíduo de construção e demolição da Grande Natal-RN

The construction industry is responsible for generating a lot of waste because of their activities. Consequently, it is noticeable the occurrence of environmental problems in terms of its disposal in inappropriate places. Faced with this problem, some studies have been conducted with the aim of developing technologies and alternatives for recycling construction and demolition waste (CDW), motivated by the scarcity of natural resources and reduction of environmental problems generated. The research aims to characterize the recycled aggregates derived from construction and demolition waste (CDW) produced in the Greater Natal-RN and analyze the performance of mortar coating produced with recycled aggregates. The study includes the chemical , physical and microstructural characterization of recycled aggregates , as well as conducting microscopic analysis and laboratory tests in the fresh state (consistency index , water retention , bulk density and content of entrained air ) and in the hardened state ( compressive strength , tensile strength in bending , water absorption by immersion and capillary , mass density and void ratio ) for mortars produced from different levels of substitution of aggregates ( 0, 20 %, 40 %, 60 %, 80 % and 100 %). The results were satisfactory, providing mortars produced with recycled aggregates, smaller mass density and dynamic modulus values as well as an increase in the rates of absorption and porosity. The tensile strength in bending and compression for TP1 (1:2:8) trait were lower for mortars produced with recycled aggregates and the best result was 20% for replacement. For the TP2 (1:8) mapping, there was an increase in resistance to traction and compression and the best result was for 100% replacement of natural aggregates by recycled. The experiments led to the conclusion that the technical and economic point of view that the mortars produced with recycled aggregates can be used in construction, only if there is an effective control in production processes of recycled aggregate and at the dosage of mortars

Fonte de energia alternativa: um estudo sobre a percepção ambiental, social e econômica do biodiesel com docentes do Centro de Tecnologia do gás da cidade de Natal RN

Meaning fuel and renewal energy source s derivative additives, the term biodiesel exists in Brazil since 1980, when it was signed its first patent by Expedito Parente. Since then, its importance has grown gradually due to the worsening of the ambient problems, since its use has became a highly promising alternative to the pollution decrease, as in the carbon dioxide issue as with the smoke and sulfur oxide. In Brazil, it was created the National Program of Production, whose objective is to insert the new product in the country s energy matrix, strengthening the economy and creating new employment opportunities, being an important product to the national energetic independence, since Brazil still imports diesel to its domestic consumption. This study aims to identify the ambient, social and economic perception of the teachers from the Technology Center of Natal city (CTGÁS-RN) to the biodiesel. For that, it was used a questionnaire closed questions, organized in the likart scale, directed to the tree spheres of the research analysis, the biodiesel and its social, ambient and economic nuances, totaling 31 questionnaires full answered. In its objectives, the research was descriptive and in its approach it was qualitative. To the data analysis it was used statistical tools (Statistic software, 6.1 version and Microsoft Excel 2003). The research revealed the predominance of the ambient aspect in the sight of the teachers, followed by the social ones. The economic factors represent a minor percentage in the analysis when compared to other

Diagnóstico para implantação do sistema de gestão ambiental em postos revendedores de combustíveis no município de Paranamirim RN: um estudo de caso

natural resources that still enjoy, in the certainty that if we do not, could culminate at the end of that remains. The environmental contamination by fuels in the retail service of oil and biofuels, has been a subject of growing research in Brazil, due to the large pollution potential of this activity. The aim of this study was to evaluate the importance of implementing the Environmental Management System (EMS) in fuel retail service stations in the city of Parnamirim-RN, but also describe the current situation the same as licensing and environmental characterization; identify existing barriers to implementation of EMS on the costs, technologies, knowledge, vision, present the potential benefits for the implementation of the EMS (social, economic and environmental), to identify the existence of plans for future action to implement the EMS , as a subsidy to promote the implementation of it. The methodology was developed through analysis of documents provided by the environmental agency responsible for licensing of retail service stations and fuel pala ANP. For data collection, we used the questionnaire was applied directly to managers or managers of sub-stations. Data were collected in 12 of 30 posts in the municipality. For purposes of data treatment was performed a descriptive analysis with respect to the opinion of twelve managers (respondents). The data acquired, according to the Likert scale were tabulated and analyzed using software SPSS 17.0 and Excel 2003, it was generated tables and graphs to observe the behavior of the data. The results showed that most respondents have a schooling level higher (58.3%) of the jobs surveyed 50% work on average 6 to 10 years and 41.6% are in operation for over 11 years , 75.0% do not have a license to operate and 12 stations, 58.3% were sued for not having a license to operate and are therefore in full commercial activity, 83% of jobs have some practice environmentally responsible, 75% agree in making planning future action to implement 8 the EMS in their ventures, 70% in full agreement that the high cost is a form of impediment to implementation of EMS; 66.67% agreed that resistance to change is an impediment to implementation of EMS; 90.91% agreed that the implementation of EMS is very complex, 80% of respondents agreed in a very significant environmental legislation is also a key factor preventing the implementation of EMS is noteworthy that 100% of respondents agreed that the knowledge about the use of the EMS will help to solve environmental problems in the fuel retail service stations, the implementation of the EMS will benefit with increased efficiency of resources applied to the findings by the agreement of 91.66% of respondents, where only 8, 33% disagreed, there was also a percentage of 100%, agreed that the company's image will be a great benefit, but also a contribution to solving environmental problems in the fuel retail service stations. Thus, the importance of the implementation of EMS in the fuel retail service stations in the city of Parnamirim-RN, with an urgent need to be deployed. And the bodies responsible for policy on state-run and supervise more tightly and action, this type of activity, in order to regulate the sustainable functioning of retail service stations of fuel, thus promoting a better quality of life for the population of the municipality of natal-RN

Gestão ambiental na indústria do petróleo :um estudo sobre as práticas de gestão na perspectiva da aprendizagem organizacional

This work discusses the environmental management thematic, on the basis of ISO 14001 standard and learning organization. This study is carried through an exploratory survey in a company of fuel transport, located in Natal/RN. The objective of this research was to investigate the practices of environmental management, carried through in the context of an implemented ISO 14001 environmental management system, in the researched organization, from the perspective of the learning organization. The methodology used in this work is supported in the quantitative method, combining the exploratory and descriptive types, and uses the technique of questionnaires, having as scope of the research, the managers, employee controlling, coordinators, supervisors and - proper and contracted - of the company. To carry through the analysis of the data of this research, it was used software Excel and Statistical version 6.0. The analysis of the data is divided in two parts: descriptive analysis and analysis of groupings (clusters). The results point, on the basis of the studied theory, as well as in the results of the research, that the implemented ISO 14001 environmental system in the searched organization presents elements that promote learning organization. From the results, it can be concluded that the company uses external information in the decision taking on environmental problems; that the employees are mobilized to generate ideas and to collect n environmental information and that the company has carried through partnerships in the activities of the environmental area with other companies. All these item cited can contribute for the generation of knowledge of the organization. It can also be concluded that the company has evaluated environmental errors occurrences in the past, as well as carried through environmental benchmarking. These practical can be considered as good ways of the company to acquire knowledge. The results also show that the employees have not found difficulties in the accomplishment of the tasks when the manager of its sector is not present. This result can demonstrate that the company has a good diffusion of knowledge

A influência do marketing ambiental na decisão de compra dos consumidores de produtos orgânicos

The search of the man for more comfort and one better quality of life led to an increment of the production of goods and services, that results, almost always, in aggressions to the nature and to a reduction of this same quality of life. The concern with the ambient problems appears as an important element regarding the material and economic growth and of the quality of life. With this scene a new question, the Ambient Marketing appears. Although the marketing concept to be well ample, the companies use the term ambient marketing to make reference what in fact, many times, are a more specific activity of ambient communication. The ambient communication is a new form to communicate used for the companies with the objective to get advantages of its competitors ahead, since the competitiveness by means of the o price, the stated period and the quality if becomes extremely incited. In view of the current competitive market, where the organizations need distinguishing to get greater have detached front to the competition, and the fact of the society to be each time more worried about the environment and the impacts that the companies cause it, the ambient communication has been used as form to convince its customers. Of this form, she evaluated herself, through a exploratory research and qualitative, the influence of the use of the ambient communication in the decision of purchase and of that she forms the companies when using of this communication can add value to its product. The results had indicated that 77% of the interviewed ones had heard to say on marketing or ambient communication and that the television is main the media for this knowledge, a time that 90.9% of the respondents had affirmed to have seen propagandas of directed products of consumption to the ambient question in this way. In fact, the concern with the environment demonstrated for the companies has its impact, therefore 84% of the respondents had told if to sensetize with this fact. However, only a lesser number of people, 70.5% answered that this concern really influences in its decision of purchase

Gestão ambiental na educação: um estudo sobre fatores que afetam o comportamento ambiental de professores do ensino médio, na cidade de Floriano-PI

The present work sets out environmental issues in educational field. The aim of this research was to investigate the factors capable to influence the environmental behavior of the teachers in High school of the public school in Floriano, state of Piaui. For this, the methodology utilized an explanatory and descriptive search like a survey; questionnaires were applied with open and close questions establishing shifts that made up the following aspects; knowledge, behavior, responsibility, participation and trait of the teachers. The statistic techniques to analyze the data were descriptive analysis and analysis of multiple regression. The results reveal that teachers care about the real surrounding problems and believe that the school must develop ambient activities to stir the consciousness, it is important to the environmental improvement of the city. However, the results point out that are developed little activities related to theme concerned, besides the level of ambient consciousness given to the students are median. It was observed that teachers have little knowledge about theme like Agenda 21 and ISO14000. After identifying some factors of environmental knowledge, it was showed recommendations. The Agenda 21 recognizes in the educational field a mean of popular consciousness; the school should develop an education according to national policy of the environmental education

Gestão ambiental na agricultura: um estudo sobre fatores associados à conscientização ambiental em estudantes de uma escola agrotécnica

This study deals with environmental issues on agriculture. In this context, the aim of this study is investigate factors able to influence the environmental conscientization of students of a agricultural technicals school about the aspects and environmental impacts related to the agricultural productive process. Besides, the used methodology on this work was to the application of a questionnaire based in Likert-kind scale with closed questions, they are constituted of variables which consisted of groups denominated perception, attitude, communitarian sense, commitment, sel-consciousness, knowledge and student profile. Like data analysis way was used descriptive analysis and chi-square to check the association significance between the perception variable with the variable ones of cited groups. The results obtained show that the environmental knowledge variable was one of the that showed high significance when it associated to the variables of perception group. The students with environmental knowledge showed high consideration that the production activities on agriculture cause large adverse impacts on environment. After the identification of some factors of environmental conscientization are shown recommendations which school must prepare techniques in aware high school of agricultural sciences with the environmental problems which be able to apply sustainable technologies on agriculture instead of traditional ones through the benefit of environment

Análise do desempenho térmico de sistema constutivo de concreto com EPS como agregado graúdo

In the last decades there was a concentrate effort of researchers in the search for options to the problem of the continuity of city development and environmental preservation. The recycling and reuse of materials in industry have been considerate as the best option to sustainable development. One of the relevant aspects in this case refers to the rational use of electrical energy. At this point, the role of engineering is to conceive new processes and materials, with the objective of reducing energy consumption and maintaining, at the same time the benefits of the technology. In this context, the objective of the present research is to analyze quantitatively the thermal behavior of walls constructed with concrete blocks which composition aggregates the expanded polystyrene (EPS) reused in the shape of flakes and in the shape of a board, resulting in a “light concrete”. Experiments were conducted, systematically, with a wall (considerate as a standard) constructed with blocks of ordinary concrete; two walls constructed with blocks of light concrete, distinct by the proportion of EPS/sand; a wall of ceramic bricks (“eight holes” type) and a wall with ordinary blocks of cement, in a way to obtain a comparative analysis of the thermal behavior of the systems. Others tests conducted with the blocks were: stress analysis and thermal properties analysis (ρ, cp e k). Based on the results, it was possible to establish quantitative relationship between the concentration (density) of EPS in the constructive elements and the decreasing of the heat transfer rate, that also changes the others thermal properties of the material, as was proved. It was observed that the walls of light concrete presents better thermal behavior compared with the other two constructive systems world wide used. Based in the results of the investigation, there was shown the viability of the use of EPS as aggregate (raw material) in the composition of the concrete, with the objective of the fabrication of blocks to non-structural masonry that works as a thermal insulation in buildings. A direct consequence of this result is the possibility of reduction of the consume of the electrical energy used to climatization of buildings. Other aspect of the investigation that must be pointed was the reuse of the EPS as a raw material to civil construction, with a clear benefit to reducing of environmental problems

Remoção conjugada de metais e óleo de água produzida

Petroleum can be associated or not with natural gas, but in both cases water is always present in its formation. The presence of water causes several problems, such as the difficulty of removing the petroleum from the reservoir rock and the formation of waterin-oil and oil-in-water emulsions. The produced water causes environmental problems, which should be solved to reduce the effect of petroleum industry in the environment. The main objective of this work is to remove simultaneously from the produced water the dispersed petroleum and dissolved metals. The process is made possible through the use of anionic surfactants that with its hydrophilic heads interacts with ionized metals and with its lipophilic tails interacts with the oil. The studied metals were: calcium, magnesium, barium, and cadmium. The surfactants used in this research were derived from: soy oil, sunflower oil, coconut oil, and a soap obtained from a mixture of 5wt.% coconut oil and 95wt.% animal fat. It was used a sample of produced water from Terminal de São Sebastião, São Paulo. As the concentration of the studied metals in produced water presented values close to 300 mg/L, it was decided to use this concentration as reference for the development of this research. Molecular absorption and atomic absorption spectroscopy were used to determine petroleum and metals concentrations in the water sample, respectively. A constant pressure filtration system was used to promote the separation of solid and liquid phases. To represent the behavior of the studied systems it was developed an equilibrium model and a mathematical one. The obtained results showed that all used surfactants presented similar behavior with relation to metals extraction, being selected the surfactant derived from soy oil for this purpose. The values of the partition coefficients between the solid and liquid phases " D " for the studied metals varied from 0.2 to 1.1, while the coefficients for equilibrium model " K " varied from 0.0002 and 0.0009. The removal percentile for oil with all metals associated was near 100%, showing the efficiency of the process

Limonologia e qualidade ambiental de um corpo lêntico receptor de efluentes tratados da indústria de petróleo

Environmental pollution has become a subject of public interest throughout the world. Not only have developed countries been affected by environmental problems but also the developing nations have started to suffer from the serious impacts of pollution. Within this context it is necessary to collect simplified environmental data to assist in the management of water resources by the appropriate authorities. These data are obtained through an environmental index that allows a space-time comparison of points distributed in the same aquatic body, or between different water bodies, for physico-chemical and bacteriological parameters. The aim of this present study was to determine the environmental status of the Lagoa de Baixo at Guamaré/RN, where a production unit of PETROBRAS RN/CE is located. For this purpose the Water Quality Index (WQI) was used in both an add and multiply form, the Trophic State Index (TSI) and the Environmental Quality Quotient (EQQ), as well as determining the concentrations of metals. The average values obtained for the WQI, in its two forms were 68,67 and 62,76 respectively which were inside the good qualification. According to the TSI the lagoon showed characteristics of a middle trophic state, and an impact level of regular as determined by the EQQ

Preparação e caracterização de um material híbrido, à base de vermiculita modificada com quitosana, para a remoção de íons de chumbo presentes em efluentes sintéticos

Actually, surveys have been developed for obtaining new materials and methodologies that aim to minimize environmental problems due to discharges of industrial effluents contaminated with heavy metals. The adsorption has been used as an alternative technology effectively, economically viable and potentially important for the reduction of metals, especially when using natural adsorbents such as certain types of clay. Chitosan, a polymer of natural origin, present in the shells of crustaceans and insects, has also been used for this purpose. Among the clays, vermiculite is distinguished by its good ion exchange capacity and in its expanded form enhances its properties by greatly increasing its specific surface. This study aimed to evaluate the functionality of the hybrid material obtained through the modification of expanded vermiculite with chitosan in the removal of lead ions (II) in aqueous solution. The material was characterized by infrared spectroscopy (IR) in order to evaluate the efficiency of modification of matrix, the vermiculite, the organic material, chitosan. The thermal stability of the material and the ratio clay / polymer was evaluated by thermogravimetry. To evaluate the surface of the material was used in scanning electron microscopy (SEM) and (BET). The BET analysis revealed a significant increase in surface area of vermiculite that after interaction with chitosan, was obtained a value of 21, 6156 m2 / g. Adsorption tests were performed according to the particle size, concentration and time. The results show that the capacity of removal of ions through the vermiculite was on average 88.4% for lead in concentrations ranging from 20-200 mg / L and 64.2% in the concentration range of 1000 mg / L. Regarding the particle size, there was an increase in adsorption with decreasing particle size. In fuction to the time of contact, was observed adsorption equilibrium in 60 minutes with adsorption capacity. The data of the isotherms were fitted to equation Freundlich. The kinetic study of adsorption showed that the pseudo second- order model best describes the adsorption adsorption, having been found following values K2=0,024 g. mg-1 min-1and Qmax=25,75 mg/g, value very close to the calculated Qe = 26.31 mg / g. From the results we can conclude that the material can be used in wastewater treatment systems as a source of metal ions adsorbent due to its high adsorption capacity

Estudo dos parâmetros de extração de fenol de efluentes aquosos por um tensoativo não iônico

Environmental sustainability has become one of the topics of greatest interest in industry, mainly due to effluent generation. Phenols are found in many industries effluents, these industries might be refineries, coal processing, pharmaceutical, plastics, paints and paper and pulp industries. Because phenolic compounds are toxic to humans and aquatic organisms, Federal Resolution CONAMA No. 430 of 13.05.2011 limits the maximum content of phenols, in 0.5 mg.L-1, for release in freshwater bodies. In the effluents treatment, the liquid-liquid extraction process is the most economical for the phenol recovery, because consumes little energy, but in most cases implements an organic solvent, and the use of it can cause some environmental problems due to the high toxicity of this compound. Because of this, exists a need for new methodologies, which aims to replace these solvents for biodegradable ones. Some literature studies demonstrate the feasibility of phenolic compounds removing from aqueous effluents, by biodegradable solvents. In this extraction kind called "Cloud Point Extraction" is used a nonionic surfactant as extracting agent of phenolic compounds. In order to optimize the phenol extraction process, this paper studies the mathematical modeling and optimization of extraction parameters and investigates the effect of the independent variables in the process. A 32 full factorial design has been done with operating temperature and surfactant concentration as independent variables and, parameters extraction: Volumetric fraction of coacervate phase, surfactant and residual concentration of phenol in dilute phase after separation phase and phenol extraction efficiency, as dependent variables. To achieve the objectives presented before, the work was carried out in five steps: (i) selection of some literature data, (ii) use of Box-Behnken model to find out mathematical models that describes the process of phenol extraction, (iii) Data analysis were performed using STATISTICA 7.0 and the analysis of variance was used to assess the model significance and prediction (iv) models optimization using the response surface method (v) Mathematical models validation using additional measures, from samples different from the ones used to construct the model. The results showed that the mathematical models found are able to calculate the effect of the surfactant concentration and the operating temperature in each extraction parameter studied, respecting the boundaries used. The models optimization allowed the achievement of consistent and applicable results in a simple and quick way leading to high efficiency in process operation.

Desenvolvimento de um sistema foto-oxidativo visando aplicação no tratamento de águas produzidas em campos de petróleo

Increasing concern with the environment, in addition to strict laws, has induced the industries to find altenatives to the treatment of their wastes. Actually, the oil industry has sought solutions to overcome a big environmental problem, i.e., oil field produced water being discharged to the sea. These effluents have organic compounds dissolved, such as polycyclic aromatic hydrocarbons, phenols, benzene, toluene, ethylbenzene and xylenes (BTEX). These compounds are difficult to be removed and have high toxicity. The advanced oxidation processes - AOP are effective to degradation of these organic compounds, because they generate hydroxyl radicals with high potential of oxidation. This work includes the reactor photochemical development applied in the photodegradation treatment (by photo-Fenton process) of wastewaters containing organic compounds dissolved, aiming at treatment and recovery the oil field produced water. The studied reactor allowed the evaluation of two ultraviolet radiation sources that is the main factor to describe the feasibility of the photo¬Fenton treatment, i.e., sun and black light fluorescent lamps, and other relevant variables the process: concentration of reagents, irradiated area and also various reactor configurations to maximize the use of radiation. The organic matter degradation was verified with samples collected during the experimental and analyzed with a total organic carbon analyzer (TOC), which expressed the results in terms of mgC/L. The solar radiation was more effective than radiation from the lamps. it's an important factor for the operation costs cutting. Preliminary experiments applied to oil field produced water treatment have showed satisfactory results, reducing up to 76 % of organic matter

Desenvolvimento de um sistema foto-oxidativo visando aplicação no tratamento de águas produzidas em campos de petróleo

Increasing concern with the environment, in addition to strict laws, has induced the industries to find alternatives to the treatment of their wastes. Actually, the oil industry has sought solutions to overcome a big environmental problem, i.e., oil field produced water being discharged to the sea. These effluents have organic compounds dissolved, such as polycyclic aromatic hydrocarbons, phenols, benzene, toluene, ethylbenzene and xylenes (BTEX). These compounds are difficult to be removed and have high toxicity. The advanced oxidation processes - AOP are effective to degradation of these organic compounds, because they generate hydroxyl radicals with high potential of oxidation. This work includes the reactor photochemical development applied in the photodegradation treatment (by photo-Fenton process) of wastewaters containing organic compounds dissolved, aiming at treatment and recovery the oil field produced water. The studied reactor allowed the evaluation of two ultraviolet radiation sources that is the main factor to describe the feasibility of the photo- Fenton treatment, i.e., sun and black light fluorescent lamps, and other relevant variables the process: concentration of reagents, irradiated area and also various reactor configurations to maximize the use of radiation. The organic matter degradation was verified with samples collected during the experimental and analyzed with a total organic carbon analyzer (TOC), which expressed the results in terms of mgC/L. The solar radiation was more effective than radiation from the lamps. It's an important factor for the operation costs cutting. Preliminary experiments applied to oil field produced water treatment have showed satisfactory results, reducing up to 76 % of organic matter

Sistemas microemulsionados aplicados à remoção da cor de efluente têxtil

Effluent color resulting from textile dyeing processes has been one of the biggest environmental problems faced by the textile industry. In particular, reactive dyes are highly resistant to conventional wastewater treatment methods. New technologies have been contemplated, some of which have been applied in industrial treatment plants, but color removal has not been efficiently attained. Since microemulsion systems provide good results in heavy metals and proteins extraction processes, their use in dyes extraction has been suggested and investigated. In this work, a real textile wastewater from an exhaustion dyebath has been treated, which contains the following reactive dyes: Procion Yellow H-E4R (CI Reactive Yellow 84), Procion Blue H-ERD (CI Reactive Blue 160) and Procion Red H-E3B (CI Reactive Red 120), in addition to auxiliary compounds normally found in dyeing processes with reactive dyes. The dyes Remazol Blue RR and Remazol Turquoise Blue G (Reactive Blue 21) have also been examined in view of the presence of heavy metals in these molecules. The microemulsion system comprised dodecyl ammonium chloride (as a cationic surfactant), water or wastewater as aqueous phase, kerosene as oil phase, and one of the following alcohols as cosurfactant: isoamyl alcohol, n-butyl alcohol and n-octyl alcohol. The pseudo-ternary diagrams were constructed in order to define Winsor s equilibrium regions. The influence of parameters such as pH, C/S (cosurfactant/surfactant) ratio, distribution coefficient, initial dye concentration, salinity, temperature, phases relative amounts, loading capacity of the microemulsion phase and dye reextraction rate has also been investigated. An experimental planning (Scheffé Net) was used to optimize the extraction process. The removal of color and metals reached levels as high as 99%