Concreto celular polimérico: influência na adição de resíduo de poliéster insaturado termofixo

This work addresses the production of lightweight concrete building elements, such as plates, prefabricated slabs for pre-molded and panels of fencing, presenting a singular concrete: the Lightweight Concrete, with special properties such low density and good strength, by means of the joint use of industrial waste of thermosetting unsaturated polyesters and biodegradable foaming agent, named Polymeric Lightweight Concrete. This study covered various features of the materials used in the composition of the Polymeric Lightweight Concrete, using a planning of factorial design 23, aiming at studying of the strength, production, dosage processes, characterization of mechanical properties and microstructural analysis of the transition zone between the light artificial aggregate and the matrix of cement. The results of the mechanical strength tests were analyzed using a computational statistics tool (Statistica software) to understand the behavior and obtain the ideal quantity of each material used in the formula of the Polymeric Lightweight Concrete. The definition of the ideal formula has the purpose of obtaining a material with the lowest possible dry density and resistance to compression in accordance with NBR 12.646/92 (≥ 2.5 MPa after 28 days). In the microstructural characterization by scanning electron microscopy it was observed an influence of the materials in the process of cement hydration, showing good interaction between the wrinkled face of the residue of unsaturated polyesters thermosetting and putty and, consequently, the final strength. The attaining of an ideal formula, given the Brazilian standards, the experimental results obtained in the characterization and comparison of these results with conventional materials, confirmed that the developed Polymeric Lightweight Concrete is suitable for the production of building elements that are advantageous for construction

Estudo da substituição de agregados miúdos naturais por pó de pedra em concreto de cimento portland

The sharp consumption of natural resources by the construction industry has motivated numerous studies concerning the application of waste to replace partially or fully, some materials, such as aggregates, thereby reducing the environmental impact caused by the extraction of sand and crushing process. The application of stone dust from crushing process arising as an aggregate for the production of Portland cement concrete is a viable alternative in view of the high cost of natural sands, in addition to the environmental damage which causes its operation to the environment. The stone dust has reduced cost compared to natural sand because it is produced in the beds of their own quarries, which are usually located close to major urban centers. This study examined the feasibility of using stone dust from the crushing of rock gneisses in the state of Bahia, replacing natural quartz sand. In the development of scientific study was conducted to characterize physical and chemical raw materials applied and molded cylindrical specimens , using as reference values Fck 20, Fck 25 and Fck 30 MPa ( resistance characteristic of the concrete after 28 days) in following compositions stone powder: 10%, 30%, 50 %, 100% and 100% with additive. The specimens were cured and subjected to the tests of compressive strength and water absorption, then the samples were subjected to the tests of X-ray diffraction and scanning electron microscopy. The results obtained showed that the composition with 10% stone powder showed the best results regarding the physical and mechanical tests performed, confirming the reduction in compressive strength and increased water uptake increased as the content of the powder stone in the concrete composition

A objetivação do controle concreto de constitucionalidade nas decisões do Supremo Tribunal Federal

The independence of the United States and the revolutions that emerged in Europe in the eighteenth century led to the birth of the written constitution, with a mission to limit the power of the State and to ensure fundamental rights to citizens. Thus, the Constitution has become the norm and ultimate founding of the State. Because of this superiority felt the need to protect her, emerging from that constitutional jurisdiction, taking control of constitutionality of provisions his main instrument. In Brazil, the constitutionality control began with the Constitution of 1891, when "imported" the American model, which is named after incidental diffuse model of judicial review. Indeed, allowed that any judge or court could declare the unconstitutionality of the law or normative act in a concrete case. However, the Brazilian Constituent did not bring the U.S. Institute of stare decisis, by which the precedents of higher courts eventually link the below. Because of this lack, each tribunal Brazilian freely decide about the constitutionality of a rule, so that the decision took effect only between the parties to the dispute. This prompted the emergence of conflicting decisions between judicantes organs, which ultimately undermine legal certainty and the image of the judiciary. As a solution to the problem, was incorporated from the 1934 Constitution to rule that the Senate would suspend the law declared unconstitutional by the Supreme Court. With the introduction of abstract control of constitutionality, since 1965, the Supreme Court went on to also have the power to declare the invalidity of the provision unconstitutional, effectively against all without the need for the participation of the Senate. However, it remained the view that in case the Supreme Court declared the unconstitutionality of the fuzzy control law by the Senate would continue with the competence to suspend the law unconstitutional, thus the decision of the Praetorium Exalted restricted parties. The 1988 Constitution strengthened the abstract control expanding legitimized the Declaratory Action of Unconstitutionality and creating new mechanisms of abstract control. Adding to this, the Constitutional Amendment. No. 45/2004 brought the requirement of general repercussion and created the Office of Binding Precedent, both to be applied by the Supreme Court judgments in individual cases, thus causing an approximation between the control abstract and concrete constitutional. Saw themselves so that the Supreme Court, to be the guardian of the Constitution, its action should be directed to the trial of issues of public interest. In this new reality, it becomes more necessary the participation of the Senate to the law declared unconstitutional in fuzzy control by the Supreme Court can reach everyone, because such an interpretation has become obsolete. So, to adapt it to this reality, such a rule must be read in the sense that the Senate give publicity to the law declared unconstitutional by the Supreme Court, since mutated constitutional

O concreto e o simbólico no cotidiano da educação em saúde: práticas, representações e processo identitário dos agentes comunitários de saúde de João Pessoa PB

The present study is about an etnographic research based on the Theory of Social Representation and its complementary approach, the Theory of Central Core based on the bourdiesianos concepts of field and habitus , concerning that these concepts, articulated to the constructed social representation, may contribute to the study of social identities. Its aim is to acknowledge which identity references community health agents (CHA), agents from Community Health Agent Program (CHAP) and Family Health Program (FHP) from João Pessoa PB and which social representation is constructed by them towards health education. The study had the participation of 119 CHAs, from which 90,3 % were female and 9,7% were male. Since the identity is also built by the representation of others towards the group, 63 professionals of the FHP group (16 nurses, 16 nursing assistents, 12 doctors, 9 dentists, 6 dentistry office assistents, 4 coordinators, 1 psicologist and 1 receptionist) and 1 nurse from CHAP took part of the study, oficial documents from the Health Ministry were analyzed, verbal information from its representatives were also taken into consideration, as well as reports from the many benefitiaries of the CHA, CHAP and FHP. For data collecting, we used the combination of (a) Direct Observation and Participant Observation of the functioning micro-areas of the CHA at the Family Health Units, and the Union of the Agents; (b) Free-Association of words and expressions to stimulate the CHA , Health Education and Health ; (c) Questionnaire; (d) Interviews. The interviews were submitted to a thematic analysis of its topic. The free-association was analyzed taking in consideration the vèrgesiana proposal (a combination of the frequency and average order of evocation) which treatment enabled the identification of the central and peripheral systems of social representation towards health education and the community health agent. A test of central refutation, associated to the analysis of the indicated evocations as the most important, provided empirical evidence of social representation towards health education as orientation , prevention and hygiene , as well as the identity of CHA as supervisor , friend , help , important , and the link between the community and the Family Health Staff. Other professionals from CHAP, FHP and the Health Ministry share all of these representational contents, especially the concepts of friend and link , also shared by the community. A habitus towards the community health agents was identified, as a representation based on trust and friendship, which gives the professional a great importance towards the daily inconsistencies faced by the community

Estudo do comportamento no estado fresco e endurecido do concreto com incorporação de resíduo de corte de botão

This works aims at investigating the effects of adding waste from RCBP-polyester button manufacturing to Portland cement concrete, particularly regarding its consistency and mechanic strength. The RCBP used came from a button factory located in Parnamirim, RN, Brazil. The waste was added to the concrete on different ratios: 5 %, 10 %, 15 % and 20 % of the total cement mass. A sample of concrete without the RCBP was used as reference, 1:1,33:2,45:0,50. For the mechanic strength test four samples were tested with different ages (3, 7 and 28 days old) and mixtures. Furthermore, a Slump Test was also conducted in order to verify the concrete s consistency. A tendency to a reduction in the compression resistance was noticed for all samples. For the samples with 5 % and 10 %, there was also an increase in the traction resistance during inflexion, regarding the reference concrete. In the microstructural analysis, the RBCP was observed to show an irregular and porous surface, thus explaining the consistency decrease

Avaliação do concreto de cimento portland com resíduo da produção de scheelita em substituição ao agregado miúdo

From the 70`s, with the publication of the Manifesto for Environment UN Conference, held in Stockholm, in Sweden (1972), defend and improve the environment became part of our daily lives. Thus, several studies have emerged in several segments in order to reuse the waste. Some examples of waste incorporated in portland cement concrete are: rice husk ash, bagasse ash of cane sugar, powder-stone, microsilica, tire rubber, among others. This research used the residue of the mining industry Scheelite, to evaluate the incorporation of the residue composition of Portland cement concrete, replacing the natural sand. The percentage of residue were incorporated from 0% to 100%, with a variation of 10%, 11 being produced concrete mix in the ratio 1:2:3:0.60, by mass. We evaluated the following characteristics of concrete: slump test, compressive strength, tensile strength by diametral compression, water absorption, porosity and density, based on the ABNT, through tests performed in the Laboratory of Civil Construction, UFRN. The trace with the addition of 60% scheelite residue was obtained which better performance. Therefore, the use of the waste from the production of Scheelite is feasible due to the durability parameters (water absorption and porosity), sustainability, and the good results of the resistance of the concrete

Argamassas do grupo escolar Augusto Severo/RN: caracterização e incidência de manifestações patológicas

The search for cultural heritage preservation should be a constant, in order to minimize the lost of historical and cultural identity of a country. As part of this cultural heritage, highlights the importance of historical buildings. For the principles of restoration are met its important to know the state of conservation and the existing materials. Given the above, this work aims to study the pathological manifestations of the mortar coating from the Grupo Escolar Augusto Severo. For this, was conducted historical survey of the building, on-site visits with visual observation, collecting samples of mortar coating and characterization through visual and laboratory analysis, XRF, XRD, TG/DTG, OM and SEM-EDS. From the observations, pathological manifestations were found as: cracks, detachment of the coating, dirt, use of inappropriate material basis of cement, efflorescence, mold and mildew and also incompatible material base of cement. It was found that the pathological manifestations were intensified due to lack of coverage in some spots and especially the abandonment of the building, that many years does not have restoration or any other type of preventive and corrective maintenance. The results of laboratory tests indicated that the mortars studied are based on lime, with calcitic nature, and siliceous aggregate, with the presence of clay in two samples. From the samples collected, two are composed of lime, sand and clay and two by lime and sand. In this regard, it is important to conduct periodic inspections and maintenance, as well as carrying out restoration with use of material compatible with the original

Análise do desempenho térmico de sistema constutivo de concreto com EPS como agregado graúdo

In the last decades there was a concentrate effort of researchers in the search for options to the problem of the continuity of city development and environmental preservation. The recycling and reuse of materials in industry have been considerate as the best option to sustainable development. One of the relevant aspects in this case refers to the rational use of electrical energy. At this point, the role of engineering is to conceive new processes and materials, with the objective of reducing energy consumption and maintaining, at the same time the benefits of the technology. In this context, the objective of the present research is to analyze quantitatively the thermal behavior of walls constructed with concrete blocks which composition aggregates the expanded polystyrene (EPS) reused in the shape of flakes and in the shape of a board, resulting in a “light concrete”. Experiments were conducted, systematically, with a wall (considerate as a standard) constructed with blocks of ordinary concrete; two walls constructed with blocks of light concrete, distinct by the proportion of EPS/sand; a wall of ceramic bricks (“eight holes” type) and a wall with ordinary blocks of cement, in a way to obtain a comparative analysis of the thermal behavior of the systems. Others tests conducted with the blocks were: stress analysis and thermal properties analysis (ρ, cp e k). Based on the results, it was possible to establish quantitative relationship between the concentration (density) of EPS in the constructive elements and the decreasing of the heat transfer rate, that also changes the others thermal properties of the material, as was proved. It was observed that the walls of light concrete presents better thermal behavior compared with the other two constructive systems world wide used. Based in the results of the investigation, there was shown the viability of the use of EPS as aggregate (raw material) in the composition of the concrete, with the objective of the fabrication of blocks to non-structural masonry that works as a thermal insulation in buildings. A direct consequence of this result is the possibility of reduction of the consume of the electrical energy used to climatization of buildings. Other aspect of the investigation that must be pointed was the reuse of the EPS as a raw material to civil construction, with a clear benefit to reducing of environmental problems

Influência da formação de pozolanas com adição de metacaulim em concreto de alta resistência

The need to build durable structures and resistant to harsh environments enabled the development of high strength concrete, these activities generate a high cement consumption, which implies factor in CO2 emissions. Often the desired strength is not achieved using only the cement composition. This study aims to evaluate the influence of pozzolans with the addition of metakaolin on the physical mechanics of high strength concrete comparing them with the standard formulation. Assays were performed to characterize the aggregates according to NBR 7211, evaluation of cement and coarse aggregate through the trials of petrography (NBR 15577-3/08) and alkali-aggregate reaction (NBR 15577-05/08). Specimens were fabricated according to NBR 5738-1/04 with additions of 0%, 4%, 6%, 8% and 10% of metakaolin for cement mortars CP V in the formulations. For evaluation of the concrete hardened in fresh state and scattering assays were performed and compressive strength in accordance with the NBR 7223/1992 and NBR 5739-8/94 respectively. The results of the characterization of aggregates showed good characteristics regarding size analysis and petrography, as well as potentially innocuous as the alkali-aggregate reaction. As to the test of resistance to compression, all the formulations with the addition of metakaolin showed higher value at 28 days of disruption compared with the standard formulation. These results present an alternative to reduce CO2 emissions, and improvements in the quality and durability of concrete, because the fine particle size of metakaolin provides an optimal compression of the mass directly influencing the strength and rheology of the dough

Incorporação do resíduo oriundo do beneficiamento de caulim em concreto asfáltico

The municipal district of Equador-RN is located in an area of great amounts of ores, being your main economical activity the extraction and the kaolin improvement. The main originating from environmental problem that activity is the amount of generated residue, about 70% of the extracted kaolin. The residues are simply piled up in lands of the improvement companies, occupying like this a large area and causing impact in the existent flora. When dry, the residues transform powdered and for the action of the wind, they disperse, polluting the air. Being like this, the present work has as objective evaluates the incorporation of the great residue, originating from of the kaolin improvement, in partial substitution of all the employed aggregates in a conventional mixture of asphalt concrete, which was used in the paving of BR101/RN061 - passage between Ponta Negra and Ares. That evaluation was accomplished in three stages. The first refers to the evaluation of the physical, thermal and mineralogical characteristics of the residue with the intention of to classify it and to define your application as aggregate (small and great). The second refers to the physical characterization of the aggregates and of the asphalt material used in the conventional mixture. And the third, to the evaluation of the mixtures containing residue, which were elaborated starting from the conventional mixture with the gradual incorporation of the residue, from 5 to 40%, in substitution to the part of the conventional aggregates, in way to obtain similar particle size curves the one of the conventional mixture. That evaluation was accomplished through the comparison between the volumetric composition, the mechanical behavior and the susceptibility to the humidity of the mixtures containing residue with the one of the conventional mixture, and with the one of the DNIT specifications. The results show that the great residue originating from of the kaolin improvement has grains of the most varied size, being like this, it can substitute part of all the conventional aggregates and of the filler in an asphalt mixture. Besides, your mineralogical composition presented the same present minerals in the composition of conventional aggregates used in paving. The results evaluation of the volumetric composition of the mixtures containing residue indicates that it can use up to 30% of residue in substitution to the conventional aggregates. The evaluation of the mechanical behavior of those mixtures indicates that the residue increment in the studied mixtures caused an increase of the stability and a reduction of the resistance to the traction. The values obtained in the resistance to the traction meet below the minimum value specified by DNIT, but close to the value obtained in the conventional mixture. When taking in consideration the susceptibility of the same ones to the humidity, the results indicate that she can use up to 25% of residue

Influência do pré-aquecimento na adaptação marginal de dois materiais seladores de fóssulas e fissuras, analisada através de tomografia de coerência ótica

Among the non-invasive techniques employed in the prevention of caries highlights the sealing pits and fissures which is a conservative maneuver, in order to obliterate them to protect them from attack acid bacteria. Influenced by the studies of pre-heating composite resin, which has experienced great improvement in some of their physical properties, this study aimed to evaluate in vitro the superficial and internal marginal adaptation of different materials and sealants in pre-heating or not. A total of 40 extracted human third molars (n=10) that had their occlusal surfaces prepared to receive sealant. We tested two types of sealing materials: resin sealant (Fluoroshield) and low-viscosity resin (Permaflo), where 50% of previously received heated material and the other half received sealant material at room temperature. All samples were subjected to thermal cycling and pH, simulating a cariogenic oral environment, and later were analyzed appliance OCT (optical coherence tomography). The images obtained alterations were recorded and analyzed statistically. Change was considered as the emergence of bubbles, gaps and cracks in the sealant. Comparisons of the same material, assessing the fact that it is not sealed or preheated material, as well as comparisons between different materials subjected to the same temperature were carried out. The nonparametric Tukey test was used (p < 0,05). The results showed that there was statistically significant difference between both the materials analyzed, as between the situations in which the sealant material was submitted (preheated or not). On the issue of marginal adaptation and internal surface, seen through Optical coherence tomography, may suggest that there is a difference between the use of one type or another of the sealing material analyzed, with superiority attributed to resin Permaflo compared to sealant Fluroshield, telling is the same for the different techniques used

Estudo da previsão da carga de ruptura de estacas pré-moldadas de concreto

The piles are one of the most important types of solution adopted for the foundation of buildings. They are responsible for transmitting to the soil in deepe r and resistant layers loads from structures. The interaction of the foundation element with the soil is a very important variable, making indispensable your domain in order to determine the strength of the assembly and establish design criteria for each c ase of application of the pile. In this research analyzes were performed f rom experiments load tests for precast concrete piles and inve stigations of soil of type SPT, a study was performed for obtaining the ultimate load capacity of the foundation through methods extrapolation of load - settlement curve , semi - empirical and theoretic . After that, were realized comparisons between the different methods used for two types of soil a granular behavior and other cohesive. For obtaining soil paramet ers to be used i n the methods were established empirical correlations with the standard penetration number (NSPT). The charge - settlement curves of the piles are also analyzed. In the face of established comparisons was indicated the most reliable semiempirical method Déco urt - Quaresma as the most reliable for estimating the tensile strength for granular and cohesive soils. Meanwhile, among the methods studied extrapolation is recommended method of Van der Veen as the most appropriate for predicting the tensile strength.

Estudo do comportamento plástico, mecânico, microestrutural e térmico do concreto produzido com resíduo de porcelanato

Population growth experienced in major cities, allied to society s need of infra-structure, especially ones related to habitational demands, increases the consumption of construction materials. As a consequence, consumption of natural resources itself. Thus, due to this process, concrete is one of the most produced materials in civil construction. This is also due to the great diversity of its application, easiness in its execution and adequate mechanical performance, as well as low production costs. Following the same tendencies in construction development, the ceramic industry has intensified the production of porcelain ceramic tiles and floors. These are achieved by a fine finishing and receive polishing at the end of the fabrication process. This work researched the use of porcelain residues in polishing for the production of concrete. All of which; due to economical and environmental issues. This process aims to prove adequate destiny for this type of residue, due to environmental issues, incorporating it to the concrete itself; all of which provides economy in consumption of the materials that constitute concrete. Thus, the main characteristics of concrete were investigated through the inclusion of different concentration of the porcelain residue as additional trait element. The residue rates incorporated to the trait varied from 10% to 50% in relation to the cement mass, in the traits with plastic additives and without plastic additives. It is observed that the inclusion of porcelain residue produced a meaningful alteration in the consistency of fresh concrete. This residue has a fine granulometry and it considerably absorbed the water used in the concrete spreading, influencing the way this material is dealt with. Thus, the value of cement striking decreases with the increase of residues present in trait. The maximal incorporation of the residue was of 50%, massively, for the same factor water/initial cement. The use of residues in concrete results in an 40% increase in the compression resistance. It is also proportional to residue concentration of porcelain in the trait. The microstructure was also favored once porosity and concrete absorption decreases with the use of this residue. The parameters demonstrate the quality and durability of the concrete produced with this residue. The use of porcelain residue in concrete composition has not produced meaningful thermal behavior changes. Thermal conductivity, heat capacity and thermal diffusivity have been maintained basically constant

Concreto celular polimérico: influência na adição de resíduo de poliéster insaturado termofixo

This work addresses the production of lightweight concrete building elements, such as plates, prefabricated slabs for pre-molded and panels of fencing, presenting a singular concrete: the Lightweight Concrete, with special properties such low density and good strength, by means of the joint use of industrial waste of thermosetting unsaturated polyesters and biodegradable foaming agent, named Polymeric Lightweight Concrete. This study covered various features of the materials used in the composition of the Polymeric Lightweight Concrete, using a planning of factorial design 23, aiming at studying of the strength, production, dosage processes, characterization of mechanical properties and microstructural analysis of the transition zone between the light artificial aggregate and the matrix of cement. The results of the mechanical strength tests were analyzed using a computational statistics tool (Statistica software) to understand the behavior and obtain the ideal quantity of each material used in the formula of the Polymeric Lightweight Concrete. The definition of the ideal formula has the purpose of obtaining a material with the lowest possible dry density and resistance to compression in accordance with NBR 12.646/92 (≥ 2.5 MPa after 28 days). In the microstructural characterization by scanning electron microscopy it was observed an influence of the materials in the process of cement hydration, showing good interaction between the wrinkled face of the residue of unsaturated polyesters thermosetting and putty and, consequently, the final strength. The attaining of an ideal formula, given the Brazilian standards, the experimental results obtained in the characterization and comparison of these results with conventional materials, confirmed that the developed Polymeric Lightweight Concrete is suitable for the production of building elements that are advantageous for construction

Estudo da substituição de agregados miúdos naturais por pó de pedra em concreto de cimento portland

The sharp consumption of natural resources by the construction industry has motivated numerous studies concerning the application of waste to replace partially or fully, some materials, such as aggregates, thereby reducing the environmental impact caused by the extraction of sand and crushing process. The application of stone dust from crushing process arising as an aggregate for the production of Portland cement concrete is a viable alternative in view of the high cost of natural sands, in addition to the environmental damage which causes its operation to the environment. The stone dust has reduced cost compared to natural sand because it is produced in the beds of their own quarries, which are usually located close to major urban centers. This study examined the feasibility of using stone dust from the crushing of rock gneisses in the state of Bahia, replacing natural quartz sand. In the development of scientific study was conducted to characterize physical and chemical raw materials applied and molded cylindrical specimens , using as reference values Fck 20, Fck 25 and Fck 30 MPa ( resistance characteristic of the concrete after 28 days) in following compositions stone powder: 10%, 30%, 50 %, 100% and 100% with additive. The specimens were cured and subjected to the tests of compressive strength and water absorption, then the samples were subjected to the tests of X-ray diffraction and scanning electron microscopy. The results obtained showed that the composition with 10% stone powder showed the best results regarding the physical and mechanical tests performed, confirming the reduction in compressive strength and increased water uptake increased as the content of the powder stone in the concrete composition