Aditivação de pastas geopoliméricas com tetraborato de sódio e látex não iônico para cimentação de Poços de Petróleo

The development of activities in the oil and gas sector has been promoting the search for materials more adequate to oilwell cementing operation. In the state of Rio Grande do Norte, the cement sheath integrity tend to fail during steam injection operation which is necessary to increase oil recovery in reservoir with heavy oil. Geopolymer is a material that can be used as alternative cement. It has been used in manufacturing of fireproof compounds, construction of structures and for controlling of toxic or radioactive waste. Latex is widely used in Portland cement slurries and its characteristic is the increase of compressive strength of cement slurries. Sodium Tetraborate is used in dental cement as a retarder. The addition of this additive aim to improve the geopolymeric slurries properties for oilwell cementing operation. The slurries studied are constituted of metakaolinite, potassium silicate, potassium hydroxide, non-ionic latex and sodium tetraborate. The properties evaluated were: viscosity, compressive strength, thickening time, density, fluid loss control, at ambient temperature (27 ºC) and at cement specification temperature. The tests were carried out in accordance to the practical recommendations of the norm API RP 10B. The slurries with sodium tetraborate did not change either their rheological properties or their mechanical properties or their density in relation the slurry with no additive. The increase of the concentration of sodium tetraborate increased the water loss at both temperatures studied. The best result obtained with the addition of sodium tetraborate was thickening time, which was tripled. The addition of latex in the slurries studied diminished their rheological properties and their density, however, at ambient temperature, it increased their compressive strength and it functioned as an accelerator. The increase of latex concentration increased the presence of water and then diminished the density of the slurries and increased the water loss. From the results obtained, it was concluded that sodium tetraborate and non-ionic latex are promising additives for geopolymer slurries to be used in oilwell cementing operation

Influência da substituição de areia natural por pó de pedra no comportamento mecânico, microestrutural e eletroquímico de concretos

The construction industry is one of the largest consumers of natural raw materials, and concrete is considered today the most used material wide. This accentuated consumption of natural resources has generated concern with the preservation of the environment, and has motivated various studies related to the use of resid ues, which can partially or entirely substitute, with satisfactory performance, some materials such as the aggregate, and in so doing, decrease the impact on the environment caused by the produced residues. Research has been done to better understand and improve the microstructure of concrete, as well as to understand the mechanism of corrosion in reinforced steel. In this context, this work was developed aiming at discovering the influence of the substitution of natural sand by artificial sand, with rega rd to mechanical resistance, microstructure, and durability. To obtain the electrochemical parameters, an adaptation was made to the galvanostatic electrochemical method to study the corrosion in reinforced steel. Concretes of categories 20 MPa and 40 MPa were produced, containing natural sand, and concretes of the same categories were produced with artificial sand substituting the natural sand, and with the addition of sodium nitrate and sodium chloride. Due to the use of rock dust reject (artificial sand), an evaluation was made of its environmental risk. The results indicate that the concretes of category 20 MPa present a better performance than the concrete made with natural sand, thus making it a viable substitute. For the category 40 MPa, the better performance is from the concrete containing natural sand. The adaptation of the galvanostatic electrochemical technique to the study of the corrosion of reinforced steel within concrete proved to be valid for obtaining electrochemical parameters with a high degree of reliability, considering the number of degrees of freedom

Desenvolvimento de um compósito de espuma rígida de poliuretana de mamona e fibras de sisal para isolação térmica

The search for sustainable technologies that can contribute to reduce energy consumption is a great challenge in the field of insulation materials. In this context, composites manufactured from vegetal sources are an alternative technology. The principal objectives of this work are the development and characterization of a composite composed by the rigid polyurethane foam derived from castor oil (commercially available as RESPAN D40) and sisal fibers. The manufacture of the composite was done with expansion controlled inside a closed mold. The sisal fibers where used in the form of needlepunched nonwoven with a mean density of 1150 g/m2 and 1350 g/m2. The composite characterization was performed through the following tests: thermal conductivity, thermal behavior, thermo gravimetric analysis (TG/DTG), mechanical strength in compression and flexural, apparent density, water absorption in percentile, and the samples morphology was analyzed in a MEV. The density and humidity percentage of the sisal fiber were also determined. The thermal conductivity of the composites was higher than the pure polyurethane foam, the addition of nonwoven sisal fibers will become in a higher level of compact foam, reducing empty spaces (cells) of polyurethane, inducing an increase in k value. The apparent density of the composites was higher than pure polyurethane foam. In the results of water absorption tests, was seen a higher absorption percent of the composites, what is related to the presence of sisal fibers which are hygroscopic. From TG/DTG results, with the addition of sisal fibers reduced the strength to thermal degradation of the composites, a higher loss of mass was observed in the temperature band between 200 and 340 °C, related to urethane bonds decomposition and cellulose degradation and its derivatives. About mechanical behavior in compression and flexural, composites presented a better mechanical behavior than the rigid polyurethane foam. An increase in the amount of sisal fibers induces a higher rigidity of the composites. At the thermal behavior tests, the composites were more mechanically and thermally resistant than some materials commonly used for thermal insulation, they present the same or better results. The density of nonwoven sisal fiber had influence over the insulation grade; this means that, an increaser in sisal fiber density helped to retain the heat

Estudo do efeito do óxido de bário no comportamento de massas para porcelanato

In this work, it is proposed the study of the effect of barium oxide acting as synthetic flow in the behavior of masses for stoneware from the use of raw materials found in the deposits of minerals of the Rio Grande do Norte that it makes use of a great natural potential for the industrialization of the product. The porcelanato is a sophisticated product with excellent final properties being applied as ceramic coating in buildings of high standard of engineering. The raw materials selected for the development of the study had been two types of argilas, two types of feldspatos, dolomita, talco, barium carbonate and silica, being characterized by X-ray fluorescence, X-ray diffraction, granulometric analysis, dilatometric analysis and thermal analysis. Thus, it is intended to define four formulations using the cited raw materials that will be processed, conformed and sintered in the temperatures of 1150 °C, 1175 °C, 1200 °C, 1225 °C e 1250 °C. From the physical characterizations, chemical and morphologic of the formed formulations, the effect of barium oxide is determined in the physical and mechanical properties of the studied system carrying water absorption tests, linear retraction, apparent porosity, apparent specific mass, compacting curve, flexural strength and microstructural analysis by XRD and SEM. After analyzing the results, indicated that barium oxide acts as a flux of high temperature and as the ordering of structure, where the embedded glass phase has the nucleating effect phase potassium silico-aluminum reacting with free silica which together with the high content of potassium concentrated form a new crystalline phase called microcline. The masses studied with the addition of barium oxide present physical-mechanical properties highly satisfactory in reduced firing temperatures, which implies a saving in energy given off in the production and increased productivity

Aproveitamento de resíduos de cinza da cana de açúcar em massas cerâmicas

This study aimed to investigate the use of cane sugar ashes from small-scale stills of Eunápolis region, state of Bahia, in pottery mass that can be developed as porcelain stoneware. Bahia is the second largest producer of rum distillery in Brazil. In the production of rum is produced residue called bagasse, which is used to generate electricity in Power plants and in the distillery itself, generating ashes as residue, which is played in nature, causing environmental damage. We studied 5 (five) formulations of 0% 10% 20%, 30% and 40% by weight of the ash, without ignition and 3 (three) formulations of 10%, 20% and 30% with gray ash temperature of 1250ºC. The formulation at 0% by weight of ash was used for a comparison between the traditional mass of porcelain stoneware and the masses with the addition of ash calcined, replacing feldspar. The percentage by weight of kaolin and of Clay was kept the same, 30%, and all raw materials were derived from the state of Bahia. The samples were made in uniaxial array with dimensions of (60 x 20 x 5) mm and compressed to a pressure of 45 MPa. Assays were performed to characterize the raw by X-ray fluorescence, X-ray diffraction, ATD and ATG and Dilatometric analysis. The samples were sintered at temperatures of 1100°C, 1150°C, 1200°C and 1250°C, for the specimens with the ashes without ash and 1150° C and 1200° C for specimens with the gray level of calcined 60 minutes. and then we made a cooling ramp with the same rate of warming until reach ambient temperature. The sintered bodies were characterized by water absorption, porosity, linear shrinkage, bending strength and XRD of the fracture surface and the results analyzed. It was proven, after results of tests performed, that it is possible to use the ash residue of sugar cane bagasse on ceramic coating with the addition of up to 10% wt of the residue ash

Análise de desempenho de um fogão solar construído a partir de sucatas de antena de tv

Given the growing environmental crisis caused by degradation, mainly due to the use of polluting energy sources, increasing the growing use of renewable energies worldwide, with emphasis on solar energy, an abundant supply and available to everyone, which can be harnessed in several ways: electricity generation; dehydration of food; heating, disinfection and distillation and cooking. The latter has as its primary feature the viability of clean, renewable energy for society, combating ecological damage caused by large-scale use of firewood for cooking foods, use in tropical countries with high solar radiation, and has funding NGOs throughout the world with the goal of achieving low-income population. The proposed project consists of a solar cooker for concentration, working from the reflection of sunlight by a hub that they converge to a focal point at the bottom of the pot, getting lots of heat. The solar cooker under study consists of two elliptical reflecting parabolas made from the recycling of scrap TV antenna, having 0.29 m² of surface area for each antenna, which were covered by multiple mirrors of 2 mm thick and mounted on a metal structure, with correction for the mobility of the apparent movement of the sun. This structure was built with the recycling of scrap metal, possessing a relatively low cost compared with other solar cookers, around US$ 50.00. This cost becomes negligible, since that will involve a great benefit to not have fuel costs for each meal, unlike the use of gas or firewood for cooking food. The tests show that the cooker has reached the maximum temperature of 740 ° C, for boiling water in an average time of 28 minutes, cooking various types of foods such as potatoes, rice and pasta in an average time of 45 minutes and still going as a solar oven, making pizza baking and meat. These cooking times do not differ much from the cooking times on a gas stove, it becomes the solar cooker as a good consumer acceptance, and furthermore not to deliver the same gases that can poison the food as with the wood stove. Proves the viability of using the stove to cook or bake in two daily meals for a family, still presenting a position to improve his performance with the addition of new materials, equipment and techniques

Viabilidade térmica de um forno solar fabricado com sucatas de pneus

The proposed design provides a solar furnace alternative, box-like, low-cost operation to be used in cooking, comprising three scrap tires to make the recycling thereof. The tires were coupled to each other, forming an enclosure, which stood on its bottom covered by a parable multiple mirrors made from a urupema (sieve indigenous) and the inner sides of the oven aluminum sheet painted black, obtained from beer cans, thus being made to obtain the increase in the concentration of solar radiation incident on the inside of the prototype studied. Two tires were attached, leaving an air layer between them, with the function of thermal insulation. The third tire aimed to support the other two and thermally insulate the bottom of the oven. Externally was placed a metal frame with flat mirrors to reflect the incident rays into the oven, having a mobility to correct the apparent motion of the sun. Its primary feature is the viability of clean, renewable energy to society by tackling the ecological damage caused by the large-scale use of wood for cooking food. The tests show that the furnace reached the maximum temperature of 123.8 °C and baking various foods such as pizza, bun, and other lasagne in an average time 50 minutes. Proves the feasibility of using the oven. Presenting still able to improve their performance with the addition of new materials, equipment and techniques

Desidratação de polpas de frutas pelo método foam-mat

This study aimed to investigate the foam mat drying process of pineapple and mango pulp, as well as to evaluate the final product quality. Initially, the selection of fruit and additives was conducted based on density and stability determinations of mango, seriguela, umbu and pineapple foams. After selecting pineapple and mango for further studies, the fruit pulps and fruit foams were characterized in regard to their physicochemical composition. The temperature (60oC or 70oC) and the foam thickness (4 and 11 mm) were evaluated in accordance to the obtained drying curves and after model adjustment. Mango and pineapple powders obtained at the best process conditions were characterized in regard to their physicochemical composition, solubility, reconstitution time. Yoghurts were prepared with the addition of pineapple and mango powders and they were evaluated for their sensory acceptance. Results show that the best drying rates were achieved by using 70o C and layers 4mm thick for both fruits. The Page model successfully fitted the drying experimental data and it can be used as a predictive model. Pineapple and mango powders showed acid pH, high soluble solids content, low water activity (approx. 0.25), lipids between 1.46% and 2.03%, protein around 2.00%, and ascorbic acid content of 17,73 mg/100g and 14.32 mg/100g, for mango and pineapple, respectively. It was observed higher ascorbic acid retention for pineapple and mango powders processed at 70o C, which would be explained by the lower drying time applied. The fruit powders exhibited high solubility and fast reconstitution in water. The sensory acceptance indexes for yoghurts with the addition of both fruit powders were higher than 70%, which reflect the satisfactory product acceptance

Caracterização e aplicação de vermicultura natural e quimicamente modificada na adsorção de azul de metileno

Chemical modification of clays has been extremely studied in the search for improvements of their properties for use in various areas, such as in combating pollution by industrial effluents and dyes. In this work, the vermiculite was chemically modified in two ways, characterized and evaluated the adsorption of methylene blue dye. First was changed with the addition of a surfactant (hexadecyltrimethylammonium bromide, BHTA) making it an organophilic clay and then by adding an acid (HCl) by acid activation. Some analyzes were performed as X-ray fluorescence (FRX), X-ray diffraction (DRX), adsorption isotherms of methylene blue dye, infrared (FTIR) , scanning electron microscopy (SEM), thermal gravimetric analysis and spectroscopy energy dispersive (EDS). Analysis by FRX of natural vermiculite indicates that addition of silicon and aluminum, clay presents in its structure the magnesium, calcium and potassium with 16 % organic matter cations. The DRX analyzes indicated that the organic vermiculite was an insertion of the surfactant in the space between the lamellae, vermiculite and acid partial destruction of the structure with loss of crystallinity. The adsorption isotherms of methylene blue showed that there was a significant improvement in the removal of dye to the vermiculite with the addition of cationic surfactant hexadecyltrimethylammonium bromide and treatment with acid using HCl 2 mol/L. In acid vermiculites subsequently treated with surfactant, the adsorption capacity increased with respect to natural vermiculite, however was much lower compared vermiculite modified with acid and surfactant separately. Only the acidic vermiculite treated with surfactant adjusted to the Langmuir model. As in the infrared spectrometry proved the characteristics of natural vermiculite. In the organic vermiculite was observed the appearance of characteristic bands of CH3, CH2, and (CH3)4N. Already on acid vermiculite, it was realized a partial destruction with decreasing intensity of the characteristic band of vermiculite that is between 1074 and 952 cm-1. In the SEM analysis, it was observed that there was partial destruction to the acid treatment and a cluster is noted between the blades caused by the presence of the surfactant. The TG shows that the higher mass loss occurs at the beginning of the heating caused by the elimination of water absorbed on the surface between layers. In the organic vermiculite also observed a loss of mass between 150 and 300 °C caused decomposition of the alkylammonium molecules (surfactants)

Novos adsorventes para aplicação na remoção de enxofre de combustíveis

Currently the market requires increasingly pure oil derivatives and, with that, comes the need for new methods for obtaining those products that are more efficient and economically viable. Considering the removal of sulfur from diesel, most refineries uses catalytic hydrogenation process, the hydrodesulfurization. These processes needs high energy content and high cost of production and has low efficiency in removing sulfur at low concentrations (below 500 ppm). The adsorption presents itself as an efficient and economically viable alternative in relation to the techniques currently used. With that, the main purpose of this work is to develop and optimize the obtaining of new adsorbents based on diatomite, modified with two non ionic surfactants microemulsions, adding efficiency to the material, to its application on removal of sulfur present in commercial diesel. Analyses were undertaken of scanning electron microscopy (SEM), x-ray diffraction (XRD), x-ray fluorescence (XRF), thermogravimetry (TG) and N2 adsorption (BET) for characterization of new materials obtained. The variables used for diatomite modification were: microemulsion points for each surfactant (RNX 95 and UNTL 90), microemulsion aqueous phase through the use or non-use of salts (CaCl2 and BaCl2), the contact time during the modification and the contact form. The study of adsorption capacity of materials obtained was performed using a statistical modeling to evaluate the influence of salt concentration in the aqueous phase (20 ppm to 1500 ppm), finite bath temperature (25 to 60° C) and the concentration of sulphur in diesel. It was observed that the temperature and the concentration of sulphur (300 to 1100 ppm) were the most significant parameters, in which increasing their values increase the ability of modified clay to adsorb the sulphur in diesel fuel. Adsorption capacity increased from 0.43 to mg/g 1.34 mg/g with microemulsion point optimization and with the addition of salts.

Polpa de jambolão (Eugenia jambolana Lam.) fresca e desidratada: características físico-químicas, bioativas e funcionais, efeitos biológicos em Caenorhabditis elegans e uso para produção de frozen yogurt caprino probiótico

This work evaluated the fresh, spray dried (with 10 % of Arabic Gum) and freeze dried jambolan pulp (Eugenia jambolana Lam.) in regard to physicochemical (pH, moisture, water activity, average particle diameter, solubility and color), bioactive [total phenolic content (TPC), monomeric anthocyanin, pronathocyanidin (PA), total elagic acid (TEA), myricetin and cyanidin] and in vitro functionality (antioxidant, antienzymatic and antimicrobial activities]. In addition, the in vivo functionality of jambolan pulp was investigated using the Caenorhabditis elegans model for insulin signaling, longevity and induced neurodegeneration (Alzheimer’s disease and Parkinson’s disease related symptoms). The dried jambolan pulp presented TPC retention (50% to 75%), PA (90% to 98%), TEA (31% to 83%), myricetin (40% to 84%), cyanidin (72% to 84%) and antioxidant activity (15%). The fresh jambolan pulp, the freeze dried pulp and the spray dried jambolan pulp presented high enzymatic inhibitory activity against pancreatic lipase (4,4 to 5,8 mg/mL), alpha-glycosidase (10,3 to 13,8 mg/mL) and alpha-amylase (8,9 to 11,2 mg/mL). They also were active inhibitors against the pathogen S. aureus. The dried jambolan experimental samples were able to increase the expression of several genes linked to the insulin signaling pathways (SIR-2.1, PPTR-1, DAF-16, SOD-3, e CTL) and increased the lifespan in C. elegans (18,07 % - 24,34 %), besides decreasing the amyloid AB1-42 aggregation induced paralysis and MPP+ (1-methyl-4-phenylpyridinium) induced neurodegeneration. Based on that, the jambolan pulp and the spray dried jambolan pulp were further selected for the production of caprine frozen yogurt with the addition of Bifidobacterium animalis subsp. lactis BI-07. The final product were evaluated in regard to their physicochemical (pH, acidity, total solids, protein, total reducing sugars, fat, ashes, overrun, melting test), bioactive (TPC and monomeric anthocyanin, antioxidant activity, probiotic viability and sensory analysis (sensory acceptance). The results showed that samples with probiotic had lowest pH and higher acidity, TPC, anthocyanin and antioxidant activity. It was also observed low overrun (14.2% to 22.6%). vi Samples with probiotic had lower flavor scores. Overall, this research presents the jambolan as a highly functional bioactive-rich fruit with the potential to modulate important biological pathways, extend lifespan and retard the development of neurodegenerative diseases. Jambolan is an underexploited exotic fruit with a high colorant potential and this thesis shows for the first time in the literature important technological, biological and scientific data about this fruit that could be used towards the development of health-oriented food products.

Análise microestrutural de misturas cerâmicas de grês porcelanato com adição de chamote de telhas cerâmicas

MELO, Maxymme Mendes de ; PINHEIRO, Andrea Santos ; NASCIMENTO, R. M. ; MARTINELLI, Antonio Eduardo ; DUTRA, Ricardo Peixoto Suassuna ; MELO, Marcus Antônio de Freitas . Análise microestrutural de misturas cerâmicas de grês Porcelanato com adição de chamote de telhas cerâmicas. Cerâmica (São Paulo. Impresso), v. 55, p. 356-364, 2009

Efeitos da tilápia do Nilo (Oreochromis niloticus) e do enriquecimento por nutrientes sobre a comunidade planctônica em um lago artificial no semi-árido brasileiro

The major aim of this study was to test the hypothesis that the introduction of the Nile tilapia (Oreochromis niloticus) and the enrichment with nutrients (N and P) interact synergistically to change the structure of plankton communities, increase phytoplankton biomass and decrease water transparency of a semi-arid tropical reservoir. One field experiment was performed during five weeks in twenty enclosures (8m3) to where four treatments were randomly allocated: with tilapia addition (T), with nutrients addition (NP), with tilapia and nutrients addition (T+NP) and a control treatment with no tilapia or nutrients addition (C). A two-way repeated measures ANOVA was done to test for time (t), tilapia (T) and nutrient (NP) effects and their interaction on water transparency, total phosphorus, total nitrogen, phytoplankton and zooplankton. The results show that there was no effect of nutrient addition on these variables but significant fish effects on the biomass of total zooplankton, nauplii, rotifers, cladocerans and calanoid copepods, on the biovolume of Bacillariophyta, Zygnemaphyceae and large algae (GALD ≥ 50 μm) and on Secchi depth. In addition, we found significant interaction effects between tilapia and nutrients on Secchi depth and rotifers. Overall, tilapia decreased the biomass of most zooplankton taxa and large algae (diatoms) and decreased the water transparency while nutrient enrichment increased the biomass of zooplankton (rotifers) but only in the absence of tilapia. In conclusion, the influence of fish on the reservoir plankton community and water transparency was greater than that of nutrient loading. This finding suggests that biomanipulation should be a greater priority in the restoration of eutrophic reservoirs in tropical semi-arid regions

Efeitos de manipulações ascendentes e descendentes sobre a comunidade fitoplanctônica em um reservatório eutrófico no semi-árido brasileiro

Top-down (grazing) and bottom-up (nutrient, light) controls are important in freshwater ecosystems regulation. Relative importance of these factors could change in space and time, but in tropical lakes bottom-up regulation has to been appointed as more influent. Present study aimed to test the hypothesis that phytoplankton growths rate in Armando Ribeiro reservoir, a huge eutrophic reservoir in semi-arid region of Rio Grande do Norte state, is more limited by nutrient available then zooplankton grazing pressure. Bioassay was conduced monthly from September (2008) to August (2009) manipulating two levels of nutrients (with/without addition) and two level of grazers (with/without removal). Experimental design was factorial 2X2 with four treatments (X5), (i) control with water and zooplankton from natural spot ( C ), (ii) with nutrient addition ( +NP ), (iii) with zooplankton remove ( -Z ) and (iv) with zooplankton remove and nutrient addition ( -Z+NP ). For bioassay confection transparent plastic bottles (500ml) was incubate for 4 or 5 days in two different depths, Secchi`s depth (high luminosity) and 3 times Secchi`s depth (low luminosity). Water samples were collected from each bottle in begins and after incubates period for chlorophyll a concentration analysis and zoopalnktonic organisms density. Phytoplankton growths rates were calculated. Bifactorial ANOVA was performance to test if had a significant effect (p<0,005) of nutrient addition and grazers remove as well a significant interaction between factors on phytoplankton growths rates. Effect magnitude was calculated the relative importance of each process. Results show that phytoplankton growth was in generally stimulated by nutrient addition, as while zooplankton remove rarely stimulated phytoplankton growth. Some significant interactions happening between nutrient additions and grazers remove on phytoplankton growth. In conclusion this study suggests that in studied reservoir phytoplankton growth is more controlled by ascendent factors than descendent

Mapeamento cromossômico de genes ribossomais em espécies estuarinas da família Gerreidae Identificação de uniformidade cariotípica e sua empregabilidade com fins biotecnológicos - REPROGEN

Perciformes are dominant in the marine environment, characterized as the largest and most diverse fish group. Some families, as Gerreidae, popularly known as silver jennies, carapebas, or mojarras have a high economic potential to marine fish farming, natural explotation and game fishing. Genetic information of these species are of fundamental importance for their management and production. Despite exist over 13,000 marine fish species described, only 2% were cytogenetically analyzed and less than 1% have some reproductive characteristics known. Induced breeding, cytogenetic characterization and cryopreservation of gametes, represent important areas in applied fish studies. In this project cytogenetic analyzes were performed to acess genetic aspects of Gerreidae species, distributed in coastal and estuarine regions of Northeast Brazil. Different methods for identifying chromosomal regions were employed using conventional techniques (Ag-NORs, C-banding), staining with base-specific fluorochromes (DAPI-CMA3), and physical mapping of ribosomal genes 18S and 5S rDNA, through hybridization in situ with fluorescent probes (FISH). The six species analyzed showed remarkable chromosome conservatism. The 18S and 5S ribosomal genes when analyzed in phylogenetic perspective demonstrate varied evolutionary dynamics, suggesting ocurrence of stasis process in some groups and greater dynamism in others. Double FISH with 18S and 5S probes showed both how efficient cytotaxonomic markers in the homogeneous karyotypes of this group of species. The karyotypic pattern identified in addition to the evolutionary aspects of karyotype, are suggestive of existence of low potential of post-zygotic barrier, prompting further research to prospect for artificial interspecific hybridization of these species of commercial importance