A influência da adição de caulim, quartzo e feldspato potássico na formulação de massas cerâmicas para telhas: Modelo estatístico

The production of roof tiles in the state of Rio Grande do Norte accounts for around 60% of the total of ceramic pieces produced. There is a need for investment to improve quality and productivity, thereby promoting technological innovations. Accordingly, the aim of this study is to determine the effect of kaolin, potassium feldspar and quartz in two standard formulations, as well as the effect of sintering temperature on the technological properties of linear firing shrinkage, water absorption and bending rupture stress, by fitting the statistical model and using multiple linear regression to assess the relationship between technological properties and independent variables. The raw materials were characterized using the following techniques: X-ray fluorescence (XRF), X-ray diffraction (XRF), rational analysis (RA), differential thermal analysis (DTA) and granulometric analysis (GA). The test specimens were compacted by uniaxial pressure (25 MPa), dried in a stove at 110 ºC for 24 hours and sinterized at 850 ºC, 950 ºC and 1050 ºC and held isothermal for 30 minutes. The results obtained indicate that the addition of kaolin to two standard formulations (M and R) promoted a reduction in water absorption values and an increase in bending rupture stress values. The sintering temperatures for group M that resulted in the lowest linear firing shrinkage and water absorption values were 850 ºC and 950 ºC, respectively, and the highest bending rupture stress values were reached at a temperature of 950 ºC. In the case of group R, the sintering temperature that obtained the lowest water absorption and linear firing shrinkage values was 850 ºC, and the highest bending rupture stress values were attained at a temperature of 1050 ºC. This work explains the statistical approach used to fit the model that describes the relationship between the technological properties and percentage of kaolin, quartz and feldspar, as well as the models that enable predictions, provided that the lower and upper limits of the percentage of clay minerals, flux and quartz used in this study are respected. Statistica 6 software was used and results were obtained by stepwise forward regression

A motivação e o significado do trabalho de bancários: estudo comparativo entre dois momentos do processo de reestruturação produtiva

This master s dissertation deals with motivation and the meaning of work amongst bank employees. This is done considering a cognitive perception. Work is understood here under a social and subjective comprehension, once it deals with significance attribution. Motivation is the process that rules choice of the different possibilities of individual behavior, all of which according to the Expectation Theory. This study aims to analyze the implications of the productive restructure, since it is related to technological innovation, organizational changes and management, in motivation and work significance. Thus, the objective of the research is to verify motivational differences and the meaning of work amongst bank employees. This is done in two distinct moments of the productive restructure of bank employees in Natal-RN. The research is divided in two parts. In the first one, changes that occurred in banks between 1999 until 2005 were identified by the means of interviews with 7 bank managers. The analyzed perspective was training intensifying, quality emphasis of customer attendance, the use of automation/technology, staff stabilization, change in staff profile, work intensification, etc. In the second study the Inventory of Motivation and Work Meaning was applied. Thus, questions related to work focus, social demographic data, in 187 bank employees were dealt with. The collected data was compared to data from previous work. It was observed that productive restructure has a reflection in the meaning of work increasing self-expression, economical reward, and responsibility in work conditions. All of the item mention beforehand maintain the level of inhumanness and consummation and respond as being the characteristics of the real work environment. On the other hand, bank employees value less justice, self-expression and more the survival perspective, implying instrumental values to work. As for motivation, it is increased among bank employees. These employees have greater expectations that their work produce results since they believe in their interference in work results

Elaboração de ferramenta computacional para aprendizado da anatomia do pescoço

The teaching-learning process requires a constant search on the part of educators for didatic innovations aimed at improving learning. Among these are technological innovations our students are familiar with. In human anatomy teaching, these innovations are increasingly important, since the need for “mechanizing” many structures may make learning tiresome and nonstimulating for students. The search for new technologies may make this process simpler. Another important issue is the need to constantly emphasize applying the knowledge in question, in order for students to better understand the meaning of learning. Accordingly, this project aims to develop an interactive tablet application for neck anatomy. This application will function as a guide to dissection, containing text, photographs, drawings and videos, distributed systematically, with a script emphasizing the clinical and surgical importance of neck anatomy.

Revestimento decorativo monocamada pigmentado, com resíduo de vidro temperado, para aplicação em fachadas

Although efficient from a technical point of view, mortar layers that make up the traditional masonry coating (slurry mortar, plaster and plaster) have to be in contradiction with the new construction technologies and more efficient methods of consumption and work rationalization. From an environmental point of view, the recovery of waste into new composites for the building has been a growing strand of studies in the scientific community, may prove to be a cost-effective solution in some cases. Thus, this research proposes the development of a mortar Decorative Coating Monolayer (RDM), for use in facades, produced on site, incorporating tempered glass waste (RVT) in the cement matrix, as a partial substitute for aggregate. Therefore, we adopted the binder respect / aggregate of 1: 6 (by volume), consistency index 250mm ± 20, sand substitution levels of glass waste 20%, 50% and 80% and relative water / cement varied in many traits. Two additives were used, a polymer, styrene-butadiene-based, and other chemical, besides mineral and silica fume inorganic pigment in colors red, yellow and blue. Mechanical tests were carried out on fresh pasta and hardened, as well as for the applied coating on masonry, so as to demonstrate the feasibility of the material. In addition, it verified the adequacy of the RDM built environment by means of thermal tests. The results demonstrated the feasibility of the proposed RDM with significantly higher values when compared to norms, especially the dash-added replacement content of 20% and addition of pigment in red. Therefore, the study shows the scientific community as an incentive to the use of technological innovations in construction, increasing the range of alternatives available for housing production, with the proposition of a material that achieves the desired functionality and obtain environmental gain, and may be adopted on construction sites as an alternative industrialized mortars.

Links hipertextuais na comunicação científica: análise webométrica dos sítios acadêmicos latino-americanos em ciências sociais

VANTI, Nadia. Links hipertextuais na comunicação científica: análise webométrica dos sítios acadêmicos latino-americanos em Ciências Sociais. Porto Alegre, 2007. 292 f. Tese (Doutorado em Comunicação e Informação) – Universidade Federal do Rio Grande do Sul. Porto Alegre, 2007.

A arte de montar equipes colaborativas

Bezerra, Gesiane Ferreira et. al. A arte de montar equipes colaborativas. In: SEMINÁRIO DE PESQUISA DO CENTRO DE CIÊNCIAS SOCIAIS APLICADAS,16,2010. Anais eletrônico... Natal: CCSA, 2010.Disponível em: -01.pdf>. Acesso em: 25 nov. 2011.

Henrique Novaes: técnica, território e cidade em uma trajetória profissional: Brasil, primeira metade do século XX

The career of civil engineer Henrique de Novaes, a remarkable figure in the academic, technical and political fields, demonstrates its extensive and relevant work across Brazil in the first half of the twentieth century. It covered from the design of water supply and sewage works, road and rail transport networks, works against drought in the Northeast, hydroelectric and harbor facilities to the urbanization planning and architectural projects, which displays a systematic and multiple production. City and territory conformed to his fields of verification, practical and above all, transformation. The search for understanding of the inclusion of a social actor in this process thus contributes to the specific analysis of the doings of Henrique de Novaes, who graduated at Polytechnic School of Rio de Janeiro in 1906. From a polymorphic activity in different scales, one tries to figure how, through academic education or professional practice, urban history in Brazil can be told or built. The introduction of technological innovations matched the purposes of planning and urban sprawl, as well as met the specifications of regulation and institutionalization of public infrastructure services at the time. The overall plans proposed by the engineer thought of the city as a whole, interconnected to the structural networks. At the same time, the knowledge of a larger physical scale the territory bounces back in the urban in a relationship of reciprocity and completeness. The objective research, therefore, tries to understand the roles played by Henrique de Novaes s works and academic education in the accomplishment of systematic modernization of Brazilian urban space and territory, recovering a little known historical figure by current historiography. It is proposed, as methodological axis, that the study of this professional career configures itself as an essential element for understanding the idea of progress embodied in the technical studies and proposals for improvements and sanitation nationwide in the first half of the twentieth century . The primary sources for the construction of this analysis were technical articles in journals of the period ( Clube de Engenharia , Viação e Revista Brasileira de Engenharia ), and technical reports, government messages, newspaper articles published at the time, autobiographical reports and the engineer s verbal communications with relatives. The work is structured in three chapters: "Biographical traces, academic education and 'technical and political' activities" illustrates the initiation into the technical, public and political environment; Chapter 2, "Technique and territory" outlines his network understanding through sanitation and transport services; Chapter 3 "Technique and City" describes the influence of polytechnics knowledge on the propositions of modernization of cities; Finally, "Final Thoughts: An Evaluation," presents an overview of the affiliations and practice of an engineer in the different scales, and its contribution to the modernization of Brazilian urban and territorial space