Estudo dos parâmetros operacionais do processo de combustão in situ em reservatório de petróleo pesado

The occurrence of heavy oil reservoirs have increased substantially and, due to the high viscosity characteristic of this type of oil, conventional recovery methods can not be applied. Thermal methods have been studied for the recovery of this type of oil, with a main objective to reduce its viscosity, by increasing the reservoir temperature, favoring the mobility of the oil and allowing an increasing in the productivity rate of the fields. In situ combustion (ISC) is a thermal recovery method in which heat is produced inside the reservoir by the combustion of part of the oil with injected oxygen, contrasting with the injection of fluid that is heated in the surface for subsequent injection, which leads to loss heat during the trajectory to the reservoir. The ISC is a favorable method for recovery of heavy oil, but it is still difficult to be field implemented. This work had as an objective the parametric analysis of ISC process applied to a semi-synthetic reservoir with characteristics of the Brazilian Northeast reservoirs using vertical production and vertical injection wells, as the air flow injection and the wells completions. For the analysis, was used a commercial program for simulation of oil reservoirs using thermal processes, called Steam, Thermal and Advanced Processes Reservoir Simulator (STARS) from Computer Modelling Group (CMG). From the results it was possible to analyze the efficiency of the ISC process in heavy oil reservoirs by increasing the reservoir temperature, providing a large decrease in oil viscosity, increasing its mobility inside the reservoir, as well as the improvement in the quality of this oil and therefore increasing significantly its recovered fraction. Among the analyzed parameters, the flow rate of air injection was the one which had greater influence in ISC, obtaining higher recovery factor the higher is the flow rate of injection, due to the greater amount of oxygen while ensuring the maintenance of the combustion front

Análise paramétrica do método de injeção alternada de água e CO2(WAG) em reservatórios de petróleo

After the decline of production from natural energy of the reservoir, the methods of enhanced oil recovery, which methods result from the application of special processes such as chemical injection, miscible gases, thermal and others can be applied. The advanced recovery method with alternating - CO2 injection WAG uses the injection of water and gas, normally miscible that will come in contact with the stock oil. In Brazil with the discovery of pre-salt layer that gas gained prominence. The amount of CO2 present in the oil produced in the pre-salt layer, as well as some reservoirs is one of the challenges to be overcome in relation to sustainable production once this gas needs to be processed in some way. Many targets for CO2 are proposed by researchers to describe some alternatives to the use of CO2 gas produced such as enhanced recovery, storage depleted fields, salt caverns storage and marketing of CO2 even in plants. The largest oil discoveries in Brazil have recently been made by Petrobras in the pre -salt layer located between the states of Santa Catarina and Espírito Santo, where he met large volumes of light oil with a density of approximately 28 ° API, low acidity and low sulfur content. This oil that has a large amount of dissolved CO2 and thus a pioneering solution for the fate of this gas comes with an advanced recovery. The objective of this research is to analyze which parameters had the greatest influence on the enhanced recovery process. The simulations were performed using the "GEM" module of the Computer Modelling Group, with the aim of studying the advanced recovery method in question. For this work, semi - synthetic models were used with reservoir and fluid data that can be extrapolated to practical situations in the Brazilian Northeast. The results showed the influence of the alternating injection of water and gas on the recovery factor and flow rate of oil production process, when compared to primary recovery and continuous water injection or continuous gas injection

Controle aplicado a poços com método de elevação e bombeio centrífugo submerso

The Electrical Submersible Pumping is an artificial lift method for oil wells employed in onshore and offshore areas. The economic revenue of the petroleum production in a well depends on the oil flow and the availability of lifting equipment. The fewer the failures, the lower the revenue shortfall and costs to repair it. The frequency with which failures occur depends on the operating conditions to which the pumps are submitted. In high-productivity offshore wells monitoring is done by operators with engineering support 24h/day, which is not economically viable for the land areas. In this context, the automation of onshore wells has clear economic advantages. This work proposes a system capable of automatically control the operation of electrical submersible pumps, installed in oil wells, by an adjustment at the electric motor rotation based on signals provided by sensors installed on the surface and subsurface, keeping the pump operating within the recommended range, closest to the well s potential. Techniques are developed to estimate unmeasured variables, enabling the automation of wells that do not have all the required sensors. The automatic adjustment, according to an algorithm that runs on a programmable logic controller maintains the flow and submergence within acceptable parameters avoiding undesirable operating conditions, as the gas interference and high engine temperature, without need to resort to stopping the engine, which would reduce the its useful life. The control strategy described, based on modeling of physical phenomena and operational experience reported in literature, is materialized in terms of a fuzzy controller based on rules, and all generated information can be accompanied by a supervisory system

Atração e retenção de talentos em empresas de engenharia consultiva no setor de petróleo e gás natural da cidade de Natal

This study addresses the question of attraction and retention of talent in companies that produce engineering projects in the area of oil and natural gas in the city of Natal. The objectives were to identify the mechanisms that these companies use to attract and retain talented professionals and what the relationship between these practices and performance of these organizations in the market. This is a case study of a qualitative nature which were included in the fullness of companies that work in that class in the capital Potiguar. Have been applied to the managers of these companies structured questionnaires with eleven issues orientativas based on theoretical reference adopted. The research finds that managers understand the word "talent", recognize the importance of the appreciation of its employees and the development of their innate abilities to better organizational performance, much due to the fact they are acting in a market of fierce competition. His companies - though not submit the formal procedures related to the subject in question - have mechanisms that can be characterized as the attraction and retention of talent. The relationships identified in this study are consistent with the results found in other studies and put the information here can serve as the basis for that other managers, including other areas, to reach excellence in their respective industries

Inserção de fornecedores locais como fonte de desempenhos em custos de transação e legitimidade: estudo de caso na cadeia produtiva do petróleo e gás do Rio Grande do Norte

The inclusion of local suppliers in production chains has considerable impact on its performance, but most notably in its main actors. The results of this process may be of different kinds and can be analyzed from economic or institutional approaches. This study aimed to verify the existence of different performances of Petrobras due to the inclusion of local suppliers in the oil and gas production chain in the state of Rio Grande do Norte, from the viewpoints of transaction costs and the Institutional Theory. In order to this, were made the characterization of the PROMINP, the description of its actions and results, the mapping of its institutional context of reference, and identification of results obtained by Petrobras in terms of transaction costs and legitimacy. The theoretical framework is based on authors dealing with industrial concentration, as like Marshall, Krugman, Porter and Schmitz, from the sociological perspective of neoinstitucional theory, as like DiMaggio and Powell and Scott and Meyer, and transaction costs, as like Williamson. This is a qualitative research, with data collection done by consulting secondary fonts and semi-structured interviews with nineteen actors of three groups, namely: actors involved in actions of the program, representatives of enterprises and representative of Petrobras. To analyze the content was used the Suchman s model (1995) for categories associated with strategies of legitimation and fourteen variables associated with the three variables assets specificity, bounded rationality and opportunism (Williamson, 1995, 1989) in the case of transaction costs. The results indicate that PROMINP has achieved its objectives by encouraging the increased participation of local companies in the oil and gas production chain, reflecting in the economic development of the state. The Redepetro/RN, fostered and built upon the interaction of the participants, is presented as a solution of continuity to the participation of enterprises in the chain, after the closure of the actions of the program. PROMINP demands responses to coercive, legislative and regulatory pressures of the organizational field, whose institutional context of reference is wide. From the point of view of legitimacy, through strategies to gain cognitive legitimacy and maintaining pragmatic legitimacy, Petrobras can manipulate the environment, ensuring the compliance of the constituents to their technical and institutional demands. Enterprises, in turn, respond to the demands through compliance with technical demands, mainly through the certification of processes, and cultural changes. There aren t clear gains related to the transaction costs, however, gains in legitimacy can be seen as a cumulative capital that can serve as a competitive differential that generates economic gains. In terms of theoretical findings, it was found that, due to its explanatory power for actions that are difficult to explain only in economic terms, Institutional Theory may be used as theoretical support concurrent with other theories. TCE model has limitations in explaining the program actions. In the case, it s emphasized that Petrobras doesn t seek only economic efficiency, but has in its mission the commitment to social development.

Concreto celular polimérico: influência na adição de resíduo de poliéster insaturado termofixo

This work addresses the production of lightweight concrete building elements, such as plates, prefabricated slabs for pre-molded and panels of fencing, presenting a singular concrete: the Lightweight Concrete, with special properties such low density and good strength, by means of the joint use of industrial waste of thermosetting unsaturated polyesters and biodegradable foaming agent, named Polymeric Lightweight Concrete. This study covered various features of the materials used in the composition of the Polymeric Lightweight Concrete, using a planning of factorial design 23, aiming at studying of the strength, production, dosage processes, characterization of mechanical properties and microstructural analysis of the transition zone between the light artificial aggregate and the matrix of cement. The results of the mechanical strength tests were analyzed using a computational statistics tool (Statistica software) to understand the behavior and obtain the ideal quantity of each material used in the formula of the Polymeric Lightweight Concrete. The definition of the ideal formula has the purpose of obtaining a material with the lowest possible dry density and resistance to compression in accordance with NBR 12.646/92 (≥ 2.5 MPa after 28 days). In the microstructural characterization by scanning electron microscopy it was observed an influence of the materials in the process of cement hydration, showing good interaction between the wrinkled face of the residue of unsaturated polyesters thermosetting and putty and, consequently, the final strength. The attaining of an ideal formula, given the Brazilian standards, the experimental results obtained in the characterization and comparison of these results with conventional materials, confirmed that the developed Polymeric Lightweight Concrete is suitable for the production of building elements that are advantageous for construction

Avaliação da incorporação combinada dos resíduos de cascalho de perfuração de poço de petróleo e de polimento do porcelanato em cerâmica vermelha

Among the industries, those that produce ceramic porcelain for use in construction industry and oil, during the exploration and production period, play an important role in the production of waste. Much research has been carried out both by academia and the productive sector, sometimes reintroducing them in the same production line that generated them, sometimes in areas unrelated to their generation, as in the production of concrete and mortar for the construction, for example, but each one in an isolated way. In this research, the aim is to study the combined incorporation of the waste drill cuttings of oil well and the residue of the polishing of porcelain, generated in the final stage of finishing of this product in a clay matrix, for the production of red pottery, specifically bricks, ceramic blocks and tiles. The clay comes from the municipality of São Gonçalo, RN, the drilling waste is from the Natal basin, in Rio Grande do Norte, and the residue of the polishing proceeds from a ceramic porcelain of the State of Paraíba. For this purpose, we used a mixture of a plastic clay with a non-plastic, in a ratio of 50% each, settling formulations with the addition of these two residues in this clay matrix. In the formulations, both residues were incorporated with a minimum percentage of 2.5% and maximum of 12.5%, varying from 2.5% each, in each formulation, which the sum of the waste be no more than 15%. It should be noted that the residue of the polishing of ceramic porcelain is a IIa class (not inert). The materials were characterized by XRF, XRD, TG, DTA, laser granulometry and the plasticity index. The technological properties of water absorption, apparent porosity, linear shrinkage of burning, flexural tensile strength and bulk density were evaluated after the sintering of the pieces to 850 °C, 950 °C and 1050 °C, with a burning time of 3 hr, 3 hr and 30 minutes, and 3 hr and 50 minutes, respectively, with a heating rate of 10 °C/minute, for all formulations and landing of 30 minutes. To better understand the influence of each residue and temperature on the evaluated properties, we used the factorial planning and its surfaces of response for the interpretation of the results. It was found that the temperature has no statistical significance at a 95% of reliability level in flexural tensile strength and that it decreases the water absorption and the porosity, but increases the shrinkage and the bulk density. The results showed the feasibility of the desired incorporation, but adjusting the temperature to each product and formulation, and that the temperatures of 850 °C and 950 °C were the one that responded to the largest number of formulations

Estudo do resíduo fosfogesso na formulação de uma pasta para revestimento interno de edifícios

Universidade Federal do Rio Grande do Norte

Influência das tensões tectônicas na permeabilidade da formação Açu - Bacia Potiguar

The behavior of the fluid flux in oil fields is influenced by different factors and it has a big impact on the recovery of hydrocarbons. There is a need of evaluating and adapting the actual technology to the worldwide reservoirs reality, not only on the exploration (reservoir discovers) but also on the development of those that were already discovered, however not yet produced. The in situ combustion (ISC) is a suitable technique for these recovery of hydrocarbons, although it remains complex to be implemented. The main objective of this research was to study the application of the ISC as an advanced oil recovery technique through a parametric analysis of the process using vertical wells within a semi synthetic reservoir that had the characteristics from the brazilian northwest, in order to determine which of those parameters could influence the process, verifying the technical and economical viability of the method on the oil industry. For that analysis, a commercial reservoir simulation program for thermal processes was used, called steam thermal and advanced processes reservoir simulator (STARS) from the computer modeling group (CMG). This study aims, through the numerical analysis, find results that help improve mainly the interpretation and comprehension of the main problems related to the ISC method, which are not yet dominated. From the results obtained, it was proved that the mediation promoted by the thermal process ISC over the oil recovery is very important, with rates and cumulated production positively influenced by the method application. It was seen that the application of the method improves the oil mobility as a function of the heating when the combustion front forms inside the reservoir. Among all the analyzed parameters, the activation energy presented the bigger influence, it means, the lower the activation energy the bigger the fraction of recovered oil, as a function of the chemical reactions speed rise. It was also verified that the higher the enthalpy of the reaction, the bigger the fraction of recovered oil, due to a bigger amount of released energy inside the system, helping the ISC. The reservoir parameters: porosity and permeability showed to have lower influence on the ISC. Among the operational parameters that were analyzed, the injection rate was the one that showed a stronger influence on the ISC method, because, the higher the value of the injection rate, the higher was the result obtained, mainly due to maintaining the combustion front. In connection with the oxygen concentration, an increase of the percentage of this parameter translates into a higher fraction of recovered oil, because the quantity of fuel, helping the advance and the maintenance of the combustion front for a longer period of time. About the economic analysis, the ISC method showed to be economically feasible when evaluated through the net present value (NPV), considering the injection rates: the higher the injection rate, the higher the financial incomes of the final project

Estudo paramétrico da segregação gravitacional na injeção contínua de vapor

Steam injection is the most used method of additional recovery for the extraction of heavy oil. In this type procedure is common to happen gravitational segregation and this phenomenon can affect the production of oil and therefore, it shoulds be considered in the projects of continuous steam injection. For many years, the gravitational segregation was not adequately considered in the calculation procedures in Reservoir Engineering. The effect of the gravity causes the segregation of fluids inside the porous media according to their densities. The results of simulation arising from reservoirs could provide the ability to deal with the gravity, and it became apparent that the effects of the gravity could significantly affect the performance of the reservoir. It know that the gravitational segregation can happen in almost every case where there is injection of light fluid, specially the steam, and occurs with greater intensity for viscous oil reservoirs. This work discusses the influence of some parameters of the rock-reservoir in segregation as viscosity, permeability, thickness, cover gas, porosity. From a model that shows the phenomenon with greater intensity, optimized some operational parameters as the rate flow rate steam, distance between the wells injector-producer, and interval of completion which contributed to the reduction in gravity override, thus increasing the oil recovery. It was shown a greater technical-economic viability for the model of distance between the wells 100 m. The analysis was performed using the simulator of CMG (Computer Modeling Group-Stars 2007.11, in which was observed by iterating between studied variables in heavy oil reservoirs with similar characteristics to Brazilian Northeast

Injeção de vapor e solvente como um método de recuperação avançada em reservatório avançada em reservatórios de óleo pesado

Currently a resource more and more used by the petroleum industry to increase the efficiency of steam flood mechanism is the addition of solvents. The process can be understood as a combination of a thermal method (steam injection) with a miscible method (solvent injection), promoting, thus, the reduction of interfacial tensions and oil viscosity. The use of solvent alone tends to be limited because of its high cost. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a zone of low viscosity between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method, a numerical study of the process was done contemplating the effects of some operational parameters (distance between wells, injection steam rate, kind of solvent and injected solvent volume)on the accumulated production of oil, recovery factor and oil-steam rate. Semisynthetic models were used in this study but reservoir data can be extrapolated for practical applications situations on Potiguar Basin. Simulations were performed in STARS (CMG, 2007.11). It was found that injected solvent volumes increased oil recovery and oil rates. Further the majority of the injected solvent was produced and can be recycled

Uso de argilominerais e diatomita como adsorvente de fenóis em águas produzidas na indústria de petróleo

The oil production in Brazil has been increasing each year. Consequently, increasing volumes of water produced are generated with large quantities of contaminants, which brings many problems in disposing of these waters. The concern that the concentrations of contaminants in water produced meet existing laws for disposal of effluents, has been extremely important for the development of different techniques for treatment of water produced. The study of clay minerals as adsorbents of organic contaminants has grown considerably so in order to combine the low cost with the efficiency of environmental preservation and health issues. Thus, this study aims to understand the characteristics of vermiculite clay, sodium bentonite, calcium bentonite and diatomite and evaluate their performance as adsorbents for phenol in the water produced. Through adsorption isotherms it was possible to observe the behavior of these adsorptive clay and diatomite for adsorption of phenol, the main phenolic compound found in water produced. Different concentrations of synthetic solutions of phenol were put in touch with these adsorbents under same conditions of agitation and temperature. The adsorbents were composted adsorptive favorable, but the vermiculite and diatomite showed little capacity for absorption, being suggested for absorbs small concentrations of phenol in the balance isothermal

Diagnóstico da possível influência da atividade petrolífera em sedimentos de fundo da Bacia Piranhas-Açu, região Baixo Açu/RN

It is located in an area of increasing oil exploration, the region of the Lower Açu is at the mercy of a possible pollution generated by this economic activity, which includes various chemical substances harmful to health, such as metals. This thesis aims to, diagnose the areas of River Piranhas-Açu, a region of the Lower Açu, which are polluted by traces factors and more. In this study, it was determined the concentration of the chemica elements Al, CD, Cr, Cu, Fe, Mn, Ni, P, Pb, V and Zn, through the technique of ICP-OES analysis and the size of sediments and their contents organic matter. Were mapped by GPS, 12 points from collections. The interpretations of the results, together associating that allowed pollution to a possible contamination by oil activity. The results showed tha some regions have low concentrations of cadmium, lead, copper, manganese and zinc unable to promote damage to human health. However, there are places where the concentrations of certain metals chromium, iron and zinc are moderately polluted compared to the results with the reference values of literature and others that are highly polluted by iron. However, due to a greater number of wells in production in those locations, those higher concentrations, it can be suggested a possible influence of oi production in some areas with concentrations of chromium and lead are higher than the rest of the points of monitoring. Moreover, it is observed that the highest levels of metals found in sediment of finer texture and more organic matter content

Aplicação de termogravimetria acoplada à espectrometria de massas para caracterização de petróleo e determinação da curva de evolução de gás sulfídrico

With the new discoveries of oil and gas, the exploration of fields in various geological basins, imports of other oils and the development of alternative fuels, more and more research labs have evaluated and characterized new types of petroleum and derivatives. Therefore the investment in new techniques and equipment in the samples analysis to determine their physical and chemical properties, their composition, possible contaminants, especification of products, among others, have multiplied in last years, so development of techniques for rapid and efficient characterization is extremely important for a better economic recovery of oil. Based on this context, this work has two main objectives. The first one is to characterize the oil by thermogravimetry coupled with mass spectrometry (TG-MS), and correlate these results with from other types of characterizations data previously informed. The second is to use the technique to develop a methodology to obtain the curve of evaluation of hydrogen sulfide gas in oil. Thus, four samples were analyzed by TG-MS, and X-ray fluorescence spectrometry (XRF). TG results can be used to indicate the nature of oil, its tendency in coke formation, temperatures of distillation and cracking, and other features. It was observed in MS evaluations the behavior of oil main compounds with temperature, the points where the volatilized certain fractions and the evaluation gas analysis of sulfide hydrogen that is compared with the evaluation curve obtained by Petrobras with another methodology

Análise de modelos geológicos utilizando percolação dinâmica

In the present study we elaborated algorithms by using concepts from percolation theory which analyze the connectivity conditions in geological models of petroleum reservoirs. From the petrophysical parameters such as permeability, porosity, transmittivity and others, which may be generated by any statistical process, it is possible to determine the portion of the model with more connected cells, what the interconnected wells are, and the critical path between injector and source wells. This allows to classify the reservoir according to the modeled petrophysical parameters. This also make it possible to determine the percentage of the reservoir to which each well is connected. Generally, the connected regions and the respective minima and/or maxima in the occurrence of the petrophysical parameters studied constitute a good manner to characterize a reservoir volumetrically. Therefore, the algorithms allow to optimize the positioning of wells, offering a preview of the general conditions of the given model s connectivity. The intent is not to evaluate geological models, but to show how to interpret the deposits, how their petrophysical characteristics are spatially distributed, and how the connections between the several parts of the system are resolved, showing their critical paths and backbones. The execution of these algorithms allows us to know the properties of the model s connectivity before the work on reservoir flux simulation is started