Low cost BIST techniques for linear and non-linear analog circuits

With the ever increasing demands for high complexity consumer electronic products, market pressures demand faster product development and lower cost. SoCbased design can provide the required design flexibility and speed by allowing the use of IP cores. However, testing costs in the SoC environment can reach a substantial percent of the total production cost. Analog testing costs may dominate the total test cost, as testing of analog circuits usually require functional verification of the circuit and special testing procedures. For RF analog circuits commonly used in wireless applications, testing is further complicated because of the high frequencies involved. In summary, reducing analog test cost is of major importance in the electronic industry today. BIST techniques for analog circuits, though potentially able to solve the analog test cost problem, have some limitations. Some techniques are circuit dependent, requiring reconfiguration of the circuit being tested, and are generally not usable in RF circuits. In the SoC environment, as processing and memory resources are available, they could be used in the test. However, the overhead for adding additional AD and DA converters may be too costly for most systems, and analog routing of signals may not be feasible and may introduce signal distortion. In this work a simple and low cost digitizer is used instead of an ADC in order to enable analog testing strategies to be implemented in a SoC environment. Thanks to the low analog area overhead of the converter, multiple analog test points can be observed and specific analog test strategies can be enabled. As the digitizer is always connected to the analog test point, it is not necessary to include muxes and switches that would degrade the signal path. For RF analog circuits, this is specially useful, as the circuit impedance is fixed and the influence of the digitizer can be accounted for in the design phase. Thanks to the simplicity of the converter, it is able to reach higher frequencies, and enables the implementation of low cost RF test strategies. The digitizer has been applied successfully in the testing of both low frequency and RF analog circuits. Also, as testing is based on frequency-domain characteristics, nonlinear characteristics like intermodulation products can also be evaluated. Specifically, practical results were obtained for prototyped base band filters and a 100MHz mixer. The application of the converter for noise figure evaluation was also addressed, and experimental results for low frequency amplifiers using conventional opamps were obtained. The proposed method is able to enhance the testability of current mixed-signal designs, being suitable for the SoC environment used in many industrial products nowadays.

A Modular and digitally programmable interface based on band-pass sigma-delta modulator for mixed-signal systems-on-chip

The focus of this thesis is to discuss the development and modeling of an interface architecture to be employed for interfacing analog signals in mixed-signal SOC. We claim that the approach that is going to be presented is able to achieve wide frequency range, and covers a large range of applications with constant performance, allied to digital configuration compatibility. Our primary assumptions are to use a fixed analog block and to promote application configurability in the digital domain, which leads to a mixed-signal interface. The use of a fixed analog block avoids the performance loss common to configurable analog blocks. The usage of configurability on the digital domain makes possible the use of all existing tools for high level design, simulation and synthesis to implement the target application, with very good performance prediction. The proposed approach utilizes the concept of frequency translation (mixing) of the input signal followed by its conversion to the ΣΔ domain, which makes possible the use of a fairly constant analog block, and also, a uniform treatment of input signal from DC to high frequencies. The programmability is performed in the ΣΔ digital domain where performance can be closely achieved according to application specification. The interface performance theoretical and simulation model are developed for design space exploration and for physical design support. Two prototypes are built and characterized to validate the proposed model and to implement some application examples. The usage of this interface as a multi-band parametric ADC and as a two channels analog multiplier and adder are shown. The multi-channel analog interface architecture is also presented. The characterization measurements support the main advantages of the approach proposed.

Uma interface para o aumento da faixa de freqüências de operação de FPAAS

O crescente avanço nas mais diversas áreas da eletrônica, desde instrumentação em baixa freqüência até telecomunicações operando em freqüências muito elevadas, e a necessidade de soluções baratas em curto espaço de tempo que acompanhem a demanda de mercado, torna a procura por circuitos programáveis, tanto digitais como analógicos, um ponto comum em diversas pesquisas. Os dispositivos digitais programáveis, que têm como grande representante os Field Programmable Gate Arrays (FPGAs), vêm apresentando um elevado e contínuo crescimento em termos de complexidade, desempenho e número de transistores integrados, já há várias décadas. O desenvolvimento de dispositivos analógicos programáveis (Field Programmable Analog Arrays – FPAAs), entretanto, esbarra em dois pontos fundamentais que tornam sua evolução um tanto latente: a estreita largura de banda alcançada, conseqüência da necessidade de um grande número de chaves de programação e reconfiguração, e a elevada área consumida por componentes analógicos como resistores e capacitores, quando integrados em processos VLSI Este trabalho apresenta uma proposta para aumentar a faixa de freqüências das aplicações passíveis de serem utilizadas tanto em FPAAs comerciais quanto em outros FPAAs, através da utilização de uma interface de translação e seleção de sinais, mantendo características de programabilidade do FPAA em questão, sem aumentar em muito sua potência consumida. A proposta, a simulação e a implementação da interface são apresentadas ao longo desta dissertação. Resultados de simulação e resultados práticos obtidos comprovam a eficácia da proposta.