RST: Reuse through Speculation on Traces

In this thesis, we present a novel approach to combine both reuse and prediction of dynamic sequences of instructions called Reuse through Speculation on Traces (RST). Our technique allows the dynamic identification of instruction traces that are redundant or predictable, and the reuse (speculative or not) of these traces. RST addresses the issue, present on Dynamic Trace Memoization (DTM), of traces not being reused because some of their inputs are not ready for the reuse test. These traces were measured to be 69% of all reusable traces in previous studies. One of the main advantages of RST over just combining a value prediction technique with an unrelated reuse technique is that RST does not require extra tables to store the values to be predicted. Applying reuse and value prediction in unrelated mechanisms but at the same time may require a prohibitive amount of storage in tables. In RST, the values are already stored in the Trace Memoization Table, and there is no extra cost in reading them if compared with a non-speculative trace reuse technique. . The input context of each trace (the input values of all instructions in the trace) already stores the values for the reuse test, which may also be used for prediction. Our main contributions include: (i) a speculative trace reuse framework that can be adapted to different processor architectures; (ii) specification of the modifications in a superscalar, superpipelined processor in order to implement our mechanism; (iii) study of implementation issues related to this architecture; (iv) study of the performance limits of our technique; (v) a performance study of a realistic, constrained implementation of RST; and (vi) simulation tools that can be used in other studies which represent a superscalar, superpipelined processor in detail. In a constrained architecture with realistic confidence, our RST technique is able to achieve average speedups (harmonic means) of 1.29 over the baseline architecture without reuse and 1.09 over a non-speculative trace reuse technique (DTM).

Study of the audio coding algorithm of the MPEG-4 AAC standard and comparison among implementations of modules of the algorithm

Audio coding is used to compress digital audio signals, thereby reducing the amount of bits needed to transmit or to store an audio signal. This is useful when network bandwidth or storage capacity is very limited. Audio compression algorithms are based on an encoding and decoding process. In the encoding step, the uncompressed audio signal is transformed into a coded representation, thereby compressing the audio signal. Thereafter, the coded audio signal eventually needs to be restored (e.g. for playing back) through decoding of the coded audio signal. The decoder receives the bitstream and reconverts it into an uncompressed signal. ISO-MPEG is a standard for high-quality, low bit-rate video and audio coding. The audio part of the standard is composed by algorithms for high-quality low-bit-rate audio coding, i.e. algorithms that reduce the original bit-rate, while guaranteeing high quality of the audio signal. The audio coding algorithms consists of MPEG-1 (with three different layers), MPEG-2, MPEG-2 AAC, and MPEG-4. This work presents a study of the MPEG-4 AAC audio coding algorithm. Besides, it presents the implementation of the AAC algorithm on different platforms, and comparisons among implementations. The implementations are in C language, in Assembly of Intel Pentium, in C-language using DSP processor, and in HDL. Since each implementation has its own application niche, each one is valid as a final solution. Moreover, another purpose of this work is the comparison among these implementations, considering estimated costs, execution time, and advantages and disadvantages of each one.

Comparação entre métodos digitais de linearização de sensores

Na era de sistemas embarcados complexos, a interface direta de dispositivos e sistemas integrados para o mundo real demanda o uso de sensores e seus circuitos analógicos de suporte. Desde que a maioria das características físicas de um sensor requer algum tipo de calibração, este trabalho compara e discute quatro técnicas digitais de calibração adaptadas para aplicação em sistemas embarcados. Para fins de comparação, estes métodos de calibração foram implementados em Matlab5.3, e em um DSP (Digital Signal Processor) . Através das medidas realizadas durante a operação em regime do DSP, pode-se determinar parâmetros importantes de projeto, como potência dissipada e tempo de processamento. Outros critérios de comparação, como área consumida, tempo de processamento, facilidade de automação e taxa de crescimento do custo área e do custo velocidade com o aumento de resolução também foram analisados. Os resultados das implementações são apresentados e discutidos com o objetivo de descobrir qual o melhor método de calibração para aplicações em sistemas embarcados.

Designing single event upset mitigation techniques for large SRAM-Based FPGA components

This thesis presents the study and development of fault-tolerant techniques for programmable architectures, the well-known Field Programmable Gate Arrays (FPGAs), customizable by SRAM. FPGAs are becoming more valuable for space applications because of the high density, high performance, reduced development cost and re-programmability. In particular, SRAM-based FPGAs are very valuable for remote missions because of the possibility of being reprogrammed by the user as many times as necessary in a very short period. SRAM-based FPGA and micro-controllers represent a wide range of components in space applications, and as a result will be the focus of this work, more specifically the Virtex® family from Xilinx and the architecture of the 8051 micro-controller from Intel. The Triple Modular Redundancy (TMR) with voters is a common high-level technique to protect ASICs against single event upset (SEU) and it can also be applied to FPGAs. The TMR technique was first tested in the Virtex® FPGA architecture by using a small design based on counters. Faults were injected in all sensitive parts of the FPGA and a detailed analysis of the effect of a fault in a TMR design synthesized in the Virtex® platform was performed. Results from fault injection and from a radiation ground test facility showed the efficiency of the TMR for the related case study circuit. Although TMR has showed a high reliability, this technique presents some limitations, such as area overhead, three times more input and output pins and, consequently, a significant increase in power dissipation. Aiming to reduce TMR costs and improve reliability, an innovative high-level technique for designing fault-tolerant systems in SRAM-based FPGAs was developed, without modification in the FPGA architecture. This technique combines time and hardware redundancy to reduce overhead and to ensure reliability. It is based on duplication with comparison and concurrent error detection. The new technique proposed in this work was specifically developed for FPGAs to cope with transient faults in the user combinational and sequential logic, while also reducing pin count, area and power dissipation. The methodology was validated by fault injection experiments in an emulation board. The thesis presents comparison results in fault coverage, area and performance between the discussed techniques.

A BDI-based approach for the assessment of driver's decision-making in commuter scenarios

The rapid growth of urban areas has a significant impact on traffic and transportation systems. New management policies and planning strategies are clearly necessary to cope with the more than ever limited capacity of existing road networks. The concept of Intelligent Transportation System (ITS) arises in this scenario; rather than attempting to increase road capacity by means of physical modifications to the infrastructure, the premise of ITS relies on the use of advanced communication and computer technologies to handle today’s traffic and transportation facilities. Influencing users’ behaviour patterns is a challenge that has stimulated much research in the ITS field, where human factors start gaining great importance to modelling, simulating, and assessing such an innovative approach. This work is aimed at using Multi-agent Systems (MAS) to represent the traffic and transportation systems in the light of the new performance measures brought about by ITS technologies. Agent features have good potentialities to represent those components of a system that are geographically and functionally distributed, such as most components in traffic and transportation. A BDI (beliefs, desires, and intentions) architecture is presented as an alternative to traditional models used to represent the driver behaviour within microscopic simulation allowing for an explicit representation of users’ mental states. Basic concepts of ITS and MAS are presented, as well as some application examples related to the subject. This has motivated the extension of an existing microscopic simulation framework to incorporate MAS features to enhance the representation of drivers. This way demand is generated from a population of agents as the result of their decisions on route and departure time, on a daily basis. The extended simulation model that now supports the interaction of BDI driver agents was effectively implemented, and different experiments were performed to test this approach in commuter scenarios. MAS provides a process-driven approach that fosters the easy construction of modular, robust, and scalable models, characteristics that lack in former result-driven approaches. Its abstraction premises allow for a closer association between the model and its practical implementation. Uncertainty and variability are addressed in a straightforward manner, as an easier representation of humanlike behaviours within the driver structure is provided by cognitive architectures, such as the BDI approach used in this work. This way MAS extends microscopic simulation of traffic to better address the complexity inherent in ITS technologies.

Mecanismos de reconfiguração dinâmica aplicados ao projeto de um processador de imagens reconfigurável

As modernas aplicações em diversas áreas como multimídia e telecomunicações exigem arquiteturas que ofereçam altas taxas de processamento. Entretanto, os padrões e algoritmos mudam com incrível rapidez o que gera a necessidade de que esses sistemas digitais tenham também por característica uma grande flexibilidade. Dentro desse contexto, tem-se as arquiteturas reconfiguráveis em geral e, mais recentemente, os sistemas reconfiguráveis em um único chip como soluções adequadas que podem oferecer desempenho, sendo, ao mesmo tempo, adaptáveis a novos problemas e a classes mais amplas de algoritmos dentro de um dado escopo de aplicação. Este trabalho apresenta o estado-da-arte em relação a arquiteturas reconfiguráveis nos meios acadêmcio e industrial e descreve todas as etapas de desenvolvimento do processador de imagens reconfigurável DRIP (Dynamically Reconfigurable Image Processor), desde suas origens como um processador estático até sua última versão reconfigurável em tempo de execução. O DRIP possui um pipeline composto por 81 processadores elementares. Esses processadores constituem a chave do processo de reconfiguração e possuem a capacidade de computar um grande número de algoritmos de processamento de imagens, mais específicamente dentro do domínio da filtragem digital de imagens. Durante o projeto, foram desenvolvidos uma série de modelos em linguagem de descrição de hardware da arquitetura e também ferramentas de software para auxiliar nos processos de implementação de novos algorimos, geração automática de modelos VHDL e validação das implementações. O desenvolvimento de mecanismos com o objetivo de incluir a possibilidade de reconfiguração dinâmica, naturalmente, introduz overheads na arquitetura. Contudo, o processo de reconfiguração do DRIP-RTR é da ordem de milhões de vezes mais rápido do que na versão estaticamente reconfigurável implementada em FPGAs Altera. Finalizando este trabalho, é apresentado o projeto lógico e elétrico do processador elementar do DRIP, visando uma futura implementação do sistema diretamente como um circuito VLSI.