Characterization of supported cylinder-planar germanium waveguide sensors with synchrotron Infrared radiation

Cylinder-planar Ge waveguides are being developed as evanescent-wave sensors for chemical microanalysis. The only non-planar surface is a cylinder section having a 300-mm radius of curvature. This confers a symmetric taper, allowing for direct coupling into and out of the waveguide's 1-mm² end faces while obtaining multiple reflections at the central <30-μm-thick sensing region. Ray-optic calculations indicate that the propagation angle at the central minimum has a strong nonlinear dependence on both angle and vertical position of the input ray. This results in rather inefficient coupling of input light into the off-axis modes that are most useful for evanescent-wave absorption spectroscopy. Mode-specific performance of the cylinder-planar waveguides has also been investigated experimentally. As compared to a blackbody source, the much greater brightness of synchrotron-generated infrared (IR) radiation allows a similar total energy throughput, but restricted to a smaller fraction of the allowed waveguide modes. However, such angle-selective excitation results in a strong oscillatory interference pattern in the transmission spectra. These spectral oscillations are the principal technical limitation on using synchrotron radiation to measure evanescent-wave absorption spectra with the thin waveguides.

Evanescent

Exhibition of original artworks created in 2013. Evanescent is a new series produced in 2013 which premiered at the Castlemaine State Festival 15-24 March 2013. The series revisits a childhood delight and fascination with the projected image and the natural world. For me then, as it is now, a magnifying glass was a wonder; its simple optics twisted light into abstract comas and sci-fi aberrations; able to compact a whole view into a luminous, paradoxically inverted phantom that could fit literally into the palm of my hand. By curling fingers and thumb around the lens and cupping both hands around the elusive rays, and by peering into the space in which I had trapped them, I fancied that I had entered into the secret workings of the eye. Chrysalis, for example, appears as a scenic projection from a hand-held lens and simultaneously as the litter of the forest floor. It is produced with a makeshift camera-obscura. The nebulous silhouettes of trees, some blurred under the passing clouds of a summer wind resolve here and there into crisp lines curled across the surface of a fallen leaf on which a moth chrysalis adheres. The leaf assumes Brobdingnagian proportions and thickness as the evanescent image shrinks and is foreshortened then dissolves in the enlarged dust and grit. It manifests the unique sight anchored at this fixed point, to reveal what we might see if we were to become vegetable or mineral. Near and far, large and small, superimpose, trigonometrically exact in their adjacency and spatial relations, presenting us with a located point of view.Why? I want to understand more intimately the interior of the natural landscape, rather than any ‘scene’ of human presence, or the context of any cultural landmark. In the steep, bush locations in which I am making these images, my means are necessarily makeshift; my camera and an old manual-aperture lens able to be carried in a backpack with a black T-shirt as a 'dark-tent'. The project is not systematic but intuitive and responsive to prevailing conditions and the effect on the projection caused by sun, shade, weather and situation. I am guided by the response of objects, textures and surfaces to the projected image and how they modulate and map it. This is landscape, but not from a human point of view.

Using small reverse cycle air conditioners in relocatable classrooms - a case study

A 9-month study of four relocatable school buildings, each retro-fitted with small reverse cycle air conditioners (ACs), was conducted to investigate their effectiveness in heating and cooling the classrooms. A comparison with data from previous studies found the energy used by the ACs for heating these temporary classrooms was only 19–20% of the energy used by individual gas heaters installed in permanent classrooms. When equipment efficiencies were considered, the AC units supplied 20–27% less energy to heat the classrooms. The possible reasons for this reduction in supplied energy are explored in this paper. CO2 emissions for the AC units in heating mode, however, were calculated to be 16% greater than for individual gas heaters. The AC units were also used for cooling and on an average the total annual energy consumption for heating and cooling was found to be 11.6 kWh m−2. Responses to a small survey of staff and students about the use and operation of the conditioners are presented. Their responses were more favourable than the predictions of comfort levels in the classrooms using the Predicted Mean Vote–Predicted Percentage of Dissatisfaction (PMV–PPD) model, which indicated “uncomfortable” conditions on average summer days at 3:00 p.m. and average winter days at 10:00 a.m. Background noise levels in the classrooms with the air conditioners in use were above the recommended maximum design level of 45 dB(A); levels of up to 65 dB(A) were measured.

Small business peceptions of online marketing research

Concerns over the overall cost of marketing research and the cost per usable response have in large measure caused marketing practitioners to turn to online marketing research techniques, either as a solus technique, or in a mixed mode application. However, the use of e-mail and mixed mode surveys such as postal invitations to complete online questionnaires present both familiar and new issues, as the extant literature illustrates. This paper examines an earlier study before reporting findings from the present study, which employs a method that ascertains the probability of commissioning and/or responding to four survey research methods, described in scenarios and delivered using e-mail and the World Wide Web (Web). It is evident that while perceptions of e-mail, the Internet, and privacy have changed since early use of the Internet and more particularly the World Wide Web, and there is acknowledgment in the literature concerning the lower costs and faster response speeds of online marketing research, small businesses do appear to discriminate in favour of targeted online survey methods over postal surveys, portrayed as scenarios in this study. They indicate a greater likelihood of responding to targeted, hybrid email/Web surveys than traditional postal surveys.

Small business perceptions of postal and online survey research

Concerns over the overall cost of marketing research and the cost per usable response have in large measure caused marketing practitioners to turn to online marketing research techniques, either as a solus technique, or in a mixed mode application. However, the use of e-mail and mixed mode surveys such as postal invitations to complete online questionnaires present both familiar and new issues, as the extant literature illustrates. This paper examines an earlier study before reporting findings from the present study, which employs a method that ascertains the probability of commissioning four survey research methods, described in scenarios and delivered using e-mail and the World Wide Web (Web). It is evident that while perceptions of e-mail, the Internet, and privacy have changed since early use of the Internet and more particularly the World Wide Web, and there is acknowledgement in the literature concerning the lower costs and faster response speeds of online marketing research, small businesses do appear to discriminate in favour of targeted online survey methods over postal surveys, portrayed as scenarios in this study, but that this perception does not apply to all hybrid survey modes.

Experimental study on effect of loading rate on mode I delamination of z-pin reinforced laminates

This paper presents an experimental investigation on mode I delamination of z-pinned double-cantilever-beams (DCB) and associate z-pin bridging mechanisms. Tests were performed with three types of samples: big-pin with an areal density of 2%, small-pin with an areal density of 2% and small-pin with an areal density of 0.5%. The loading rates for each type of samples were set at 1 mm/min and 100 mm/min. Comparison of fracture load under different loading rates shows the rate effects on delamination crack opening and delamination growth. Optical micrographs of z-pins after pullout were also presented to identify the bridging mechanisms of z-pins under different loading rates.

Multi-market industrial organizational economic models for the internationalization process by small and medium enterprise construction design service firms

Small and medium enterprises (SMEs) are critical to strategic initiatives in an economy; however, their contribution to foreign trade is not as significant. SMEs are one of the principal driving forces in economic development. One of the greatest challenges is the internationalization process for longevity rather than seeing the process as initial market entry. The internationalization process research has typically involved four key constructs: market selection, decision to enter, entry modes and factors affecting entry modes. Past research has focused on large manufacturing firms. The export of architectural, engineering and construction (AEC) firms has undergone growth, yet there is still significant opportunity for further growth. The majority of AEC firms are SMEs. Notwithstanding assistance provided through international trade missions, organized export firm support networks and information packages by a burgeoning number of government agencies, there are still perceived barriers to market entry and long-term economic sustainability for SMEs. There are a number of problems faced by SMEs acting in foreign trade. This investigation explores the successful initial internationalization process constructs and identifies unique project-oriented sector characteristics. The study identified similarities and differences between two firms that have been exporting to various localities, including Eastern Europe, Africa, Middle East, UK, Asia and South America, for more than two decades. The similarities and differences were identified within eight major constructs: purpose, firm type, market image and design philosophy, entry mode strategy, institutional arrangement, factors affecting mode of entry, market selection and firm strategy in relation to project selection. The primary reasons for internationalization were associated with the firms' motivations related to growth and financial viability. This article discusses the various internationalization processes and strategies intrinsic to each case study and establishes a detailed set of empirical observations from which to develop further a grounded theoretical model of reflexive capability for the internationalization process. This study contributes to the body of knowledge around the SME AEC design service firm's internationalization process, as a dynamic, evolving and continuously adaptable construct for project-based sectors.

Symmetrically tapered <30-micron-thick quasi-planar Ge waveguides as chemical sensors for microanalysis

Symmetrically tapered planar IR waveguides have been fabricated by starting with a ZnS coated concave piece of single-crystal Ge, embedding it in an epoxide resin as a supporting substrate, and then grinding and polishing a planar surface until the thickness at the taper minimum is <30 μm. Such tapering is expected to enhance a waveguide's sensitivity as an evanescent wave sensor by maximizing the amount of evanescent wave energy present at the thinnest part of the waveguide. As predicted by theory, the surface sensitivity, i.e., the absorbance signal per molecule in contact with the sensing region, increases with decreasing thickness of the tapered region even while the total energy throughput decreases. The signal-to-noise ratio obtained depends very strongly on the quality of the polished surfaces of the waveguides. The surface sensitivity is superior to that obtained with a commercial Ge attenuated total reflection (ATR) accessory for several types of sample, including thin films (<10 ng) and small volumes (<1 μL) of volatile solvents. By using the waveguides, light-induced structural changes in the protein bacteriorhodopsin were observable using samples as small as ∼50 pmol (∼1 μg). In addition, the waveguide sensors can reveal the surface compositions on a single human hair, pointing to their promise as a tool for forensic fiber analysis.

The mode of pheromone evolution: evidence from bark beetles

Sex and aggregation pheromones consist of species-specific blends of chemicals. The way in which different species’ blends have evolved has been the subject of some debate. Theoretical predictions suggest that differences between species have arisen not through the accruing of small changes, but through major shifts in chemical composition. Using data on the aggregation pheromones of 34 species of bark beetle from two genera, Dendroctonus and Ips, we investigated how the distributions of the chemical components of their pheromone blends mirror their phylogenetic relationships. We tested whether there were consistent patterns that could be used to help elucidate the mode of pheromone evolution. Although there were obvious differences in pheromone blends between the two genera, the differences between species within each genus followed a less clear phylogenetic pattern. In both genera, closely related species are just as different as more distantly related species. Within Dendroctonus, particularly, most chemical components were distributed randomly across the phylogeny. Indeed, for some chemicals, closely related species may actually be more different than would be expected from a random distribution of chemical components. This argues strongly against the idea of minor shifts in pheromone evolution. Instead, we suggest that, within certain phylogenetic constraints, pheromone evolution in bark beetles is characterized by large saltational shifts, resulting in sibling species being substantially phenotypically (i.e. pheromonally) different from one another, thus agreeing with theoretical predictions.

Effect of tool speeds during friction stir lap welding on mode of fracture and fracture strength of Al 6060-T5 joints

Friction stir lap welding (FSLW) of an age hardened Al alloy and evaluations of how FS speeds affected hooking and how hooking and softening due to FS affected fracture strength of the lap welds have been conducted. It was found that increasing rotation speed and reducing welding speed (v) increased the stir zone size (AB-SZ) and also hook size (h), although a maximum value of h (hMax) reached. The features of hooks for the observed - AB-SZ-h relationships are presented and explained. It was found that when h increased to a value of ~ 0.9 mm (for the 3 mm alloy sheets), it started to invoke a significant effect on reducing fracture strength. Factors such as FS softening and insufficient joining, limited the fracture strength of the lap welds for small h values and these are presented and discussed.

Tuneable optical waveguide based on dielectrophoresis and microfluidics

In this work, an array of dielectrophoretic curved microelectrodes patterned in a microfluidic channel and integrated with a multimode rib polymeric waveguide is demonstrated. The microfluidic channel is infiltrated with suspended silica (SiO2) and tungsten trioxide (WO3) nanoparticles. The optofluidic system is found to be sensitive and responds not only to the infiltration of nanoparticle suspensions in the microfluidic channel, but also to the magnitude and frequencies of dielectrophoretic forces applied on the nanoparticles. The nanoparticles can be uniformly concentrated or repelled from the region between the curved microelectrode tips forming either a dense stream of flowing nanoparticles or a region void of nanoparticles in the evanescent sensitive region of the polymeric waveguide. The concentration and repulsion of nanoparticles from this region creates a refractive index gradient in the upper cladding of the polymeric waveguide. These conditions made it possible for light to either remain guided or be scattered as a function of dielectrophoretic settings applied on the nanoparticles. The results demonstrate that we successfully developed a novel tuneable polymeric waveguide based on dielectrophoretic assembly of nanoparticles suspended in fluids.

Compact stacked planar inverted-F antenna for passive deep brain stimulation implants

A compact meandered three-layer stacked circular planar inverted-F antenna is designed and simulated at the UHF band (902.75 – 927.25 MHz) for passive deep brain stimulation implants. The UHF band is used because it offers small antenna size, and high data rate. The top and middle radiating layers are meandered, and low cost substrate and superstrate materials are used to limit the radius and height of the antenna to 5 mm and 1.64 mm, respectively. A dielectric substrate of FR-4 of εr= 4.7 and δ= 0.018, and a biocompatible superstrate of silicone of er= 3.7 and d= 0.003 with thickness of 0.2 mm are used in the design. The resonance frequency of the proposed antenna is 918 MHz with a bandwidth of 24 MHz at return loss of −10 dB in free space. The antenna parameter such as 3D gain pattern of the designed antenna within a skin-tissue model is evaluated by using the finite element method. The compactness, wide bandwidth, round shape, and stable characteristics in skin make this antenna suitable for DBS. The feasibility of the wireless power transmission to the implant in the human head is also examined.

Multi-layer implantable antenna for closed loop deep brain stimulation system

A multi-layer circular planar inverted-F antenna is designed and simulated at the industrial, scientific, and medical (ISM) band of 915 MHz for closed loop deep brain stimulation implant. The ISM band is considered due to the capabilities of small antenna size, high data rate, and long transmission range. In the proposed four-layer antenna, the top three radiating layers are meandered, and a high permittivity substrate and superstrate materials are used to limit the radius and the height of the antenna to 3.5 mm and 2.2 mm, respectively. The bottom layer works as a ground plate. The Roger RO3210 of εr = 10.2 and δ = 0.003 is used as a dielectric substrate and superstrate. The resonance frequency of the proposed antenna is 915 MHz with a bandwidth of 12 MHz at the return loss of -10 dB in free space. The stacked layered structure reduces the antenna size, and the circular shape makes it easily implantable into the human head. The antenna parameters (e.g. 3D gain pattern), SAR value, and electric field distribution within a six layers spherical head model are evaluated by using the finite element method (FEM). The feasibility of the wireless transmission of power, control and command signal to the implant in the human head is also examined. © 2012 IEEE.

Small-signal stability assessment of active distribution networks with dynamic loads

This paper investigates small-signal stability of a distribution system with distributed generator and induction motor load, as a dynamic element. The analysis is carried out over a distribution test system with different types of induction motor loads. The system is linearised by the perturbation method. Eigenvalues and participation factors are calculated to see the modal interaction of the system. The study indicates that load voltage dynamics significantly influence the damping of a newly identified voltage mode. This mode has frequency of oscillation between the electromechanical and subsynchronous oscillation of power systems. To justify the validity of the modal analysis time domain simulation is also carried out. Finally, significant parameters of the system that affect the damping and frequency of the oscillation are identified.