Characterization of supported cylinder-planar germanium waveguide sensors with synchrotron Infrared radiation

Cylinder-planar Ge waveguides are being developed as evanescent-wave sensors for chemical microanalysis. The only non-planar surface is a cylinder section having a 300-mm radius of curvature. This confers a symmetric taper, allowing for direct coupling into and out of the waveguide's 1-mm² end faces while obtaining multiple reflections at the central <30-μm-thick sensing region. Ray-optic calculations indicate that the propagation angle at the central minimum has a strong nonlinear dependence on both angle and vertical position of the input ray. This results in rather inefficient coupling of input light into the off-axis modes that are most useful for evanescent-wave absorption spectroscopy. Mode-specific performance of the cylinder-planar waveguides has also been investigated experimentally. As compared to a blackbody source, the much greater brightness of synchrotron-generated infrared (IR) radiation allows a similar total energy throughput, but restricted to a smaller fraction of the allowed waveguide modes. However, such angle-selective excitation results in a strong oscillatory interference pattern in the transmission spectra. These spectral oscillations are the principal technical limitation on using synchrotron radiation to measure evanescent-wave absorption spectra with the thin waveguides.

Symmetrically tapered <30-micron-thick quasi-planar Ge waveguides as chemical sensors for microanalysis

Symmetrically tapered planar IR waveguides have been fabricated by starting with a ZnS coated concave piece of single-crystal Ge, embedding it in an epoxide resin as a supporting substrate, and then grinding and polishing a planar surface until the thickness at the taper minimum is <30 μm. Such tapering is expected to enhance a waveguide's sensitivity as an evanescent wave sensor by maximizing the amount of evanescent wave energy present at the thinnest part of the waveguide. As predicted by theory, the surface sensitivity, i.e., the absorbance signal per molecule in contact with the sensing region, increases with decreasing thickness of the tapered region even while the total energy throughput decreases. The signal-to-noise ratio obtained depends very strongly on the quality of the polished surfaces of the waveguides. The surface sensitivity is superior to that obtained with a commercial Ge attenuated total reflection (ATR) accessory for several types of sample, including thin films (<10 ng) and small volumes (<1 μL) of volatile solvents. By using the waveguides, light-induced structural changes in the protein bacteriorhodopsin were observable using samples as small as ∼50 pmol (∼1 μg). In addition, the waveguide sensors can reveal the surface compositions on a single human hair, pointing to their promise as a tool for forensic fiber analysis.

Long-term ethylene oxide exposure trends in US hospitals : relationship with OSHA regulatory and enforcement actions

We assessed long-term trends in ethylene oxide (EtO) worker exposures for the purposes of exposure surveillance and evaluation of the impacts of the Occupational Safety and Health Administration (OSHA) 1984 and 1988 EtO standards. We obtained exposure data from a large commercial vendor and processor of EtO passive dosimeters. Personal samples (87 582 workshift [8-hr] and 46 097 short-term [15-min] samples) from 2265 US hospitals were analyzed for time trends from 1984 through 2001 and compared with OSHA enforcement data. Exposures declined steadily for the first several years after the OSHA standards were set. Workshift exposures continued to taper off and have remained low and constant through 2001. However, since 1996, the probability of exceeding the short-term excursion limit has increased. This trend coincides with a decline in enforcement of the EtO standard. Results indicate the need for renewed intervention efforts to preserve gains made following the passage and implementation of the 1984 and 1988 EtO standards.

In-vivo cell mediated immunity in elite swimmers in response to training

This study investigated in-vivo cell-mediated immune (CMI) responses in elite swimmers over a 5-month training season, to assess the impact of intense training on changes in T-lymphocyte function. The CMI Multitest was performed early in the season after a period of rest, during peak high-intensity training, and late in the season during the precompetition taper period. The CMI tests were performed at rest prior to a morning training session. There were no significant differences between the swimmers and a control group for any of the seven CMI antigen responses at any of the test points during the season. In the swimmers, there were no significant differences in the number of positive responses to the CMI antigens between the three test points (Friedman's test = 9.6364, p = 0.47) and no significant differences for the CMI cumulative scores (Friedman's test = 11.98, p = 0.29) at each test point. There was no consistent pattern for changes in CMI cumulative scores for individual swimmers over the training season. The findings of this study indicate that, despite reported transient T-lymphocyte immunosuppression immediately after intense exercise, probably associated with acute redistribution and temporary pooling of blood T cell subsets in extremities, the T-lymphocyte function involved in CMI responses is not compromised by extended periods of training at an elite level.

Electrical discharge machining of 6061 aluminium alloy

The wire electrical discharge machining (EDM) of 6061 aluminium alloy in terms of material removal rate, kerf/slit width, surface finish and wear of electrode wire for different pulse on time and wire tension was studied. Eight experiments were carried out in a wire EDM machine by varying pulse on time and wire tension. It is found that the material removal rate increases with the increase of pulse on time though the wire tension does not affect the material removal rate. It seems that the higher wire tension facilitates steady machining process, which generates low wear in wire electrode and better surface finish. The surface roughness does not change notably with the variation of pulse on time. The appearance of the machined surfaces is very similar under all the machining conditions. The machined surface contains solidified molten material, splash of materials and blisters. The increase of the pulse on time increases the wear of wire electrode due to the increase of heat input. The wear of wire electrode generates tapered slot which has higher kerf width at top side than that at bottom side. The higher electrode wear introduces higher taper.

Wire EDM mechanism of MMCs with the variation of reinforced particle size

The size of reinforced particles notably affects the electro-discharge machining (EDM) of metal matrix composites (MMCs). This paper explores the mechanism of wire EDM of MMCs with different sizes of reinforced particles as well as the corresponding unreinforced matrix material. The mechanisms of material removal, surface generation, and taper kerf formation were investigated. This study shows that the particles’ ability to protect matrix materials from the intense heat of electric arc controls the material removal rate, surface generation, and taper of kerf. The low melting point matrix material is removed very easily, but the heat resistance reinforced particles delay the removal of material and facilitate the transfer of the workpiece material to wire electrode and vice versa. Thus, the material stays longer in touch with intense heat and affects the surface generation, wire electrode wear, and width of the kerf.