72 resultados para surface structure
em Deakin Research Online - Australia
Resumo:
Tin oxide/nitride (SnOxNy) thin films were synthesised using a filtered cathodic vacuum arc deposition system. These films were deposited at room temperature with increasing amounts of reactive nitrogen gas to alter the nanostructure. To understand the surface structure of the coatings several techniques were used including scanning electron microscopy (SEM), atomic force microscopy (AFM), x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD) and x-ray absorption spectroscopy (XAS). Preliminary results have shown that a cathodic arc can be used to deposit smooth films which exhibit a mixed tin oxide/nitride structure.
Resumo:
The double layer structure of two ionic liquids (ILs), 1-butyl-1- methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate ([Py 1,4]FAP) and 1-ethyl-3-methylimidazolium tris(pentafluoroethyl) trifluorophosphate ([EMIm]FAP) at the polarized Au(111) electrode interface is probed using Atomic Force Microscopy force measurements. The force-separation profiles suggest a multilayered morphology is present at the electrified Au(111)-IL interface, with more near surface layers detected at higher potentials. At the (slightly negative) open circuit potential, multiple ion layers are present, and the innermost layer, in contact with the Au(111) surface, is enriched in the cation due to electrostatic adsorption. Upon applying negative electrode potentials (-1.0 V, -2.0 V), stronger IL near surface structure is detected: both the number of ion layers and the force required to rupture these layers increases. Positive electrode potentials (+1.0 V, +2.0 V) also enhance IL near surface structure, but not as much as negative potentials, because surface-adsorbed anions are less effective at templating structure in subsequent layers than cations. This interfacial structure is not consistent with a double layer in the Stern-Gouy-Chapman sense, as there is no diffuse layer. The structure is consistent with a capicitative double-layer model, with a very small separation distance between the planes of charge.
Resumo:
Nanofibres having a parallel line surface texture were electrospun from cellulose acetate butyrate solutions using a solvent mixture of acetone and N,N'-dimethylacetamide. The formation mechanism of the unusual surface feature was explored and attributed to the formation of voids on the jet surface at the early stage of electrospinning and subsequent elongation and solidification of the voids into a line surface structure. The fast evaporation of a highly volatile solvent, acetone, from the polymer solution was found to play a key role in the formation of surface voids, while the high viscosity of the residual solution after the solvent evaporation ensured the line surface to be maintained after the solidification. Based on this principle, nanofibres having a similar surface texture were also electrospun successfully from other polymers, such as cellulose acetate, polyvinylidene fluoride, poly(methyl methacrylate), polystyrene and poly(vinylidene fluoride-co-hexafluoropropene), either from the same or from different solvent systems. Polarized Fourier transform infrared spectroscopy was used to measure the polymer molecular orientation within nanofibres. Schwann cells were grown on both aligned and randomly oriented nanofibre mats. The parallel line surface texture assisted in the growth of Schwann cells especially at the early stage of cell culture regardless of the fibre orientation. In contrast, the molecular orientation within nanofibres showed little impact on the cell growth.
Resumo:
Objectives: To compare hippocampal surface structure, using large deformation high dimensional mapping (HDM-LD), in subjects with temporal lobe epilepsy (TLE) with (HS+ve) and without (HS−ve) hippocampal sclerosis.
Methods: The study included 30 HS−ve subjects matched with 30 HS+ve subjects from the previously reported epilepsy patient cohort. To control for normal right–left asymmetries of hippocampal surface structure, subjects were regrouped based on laterality of onset of epileptic seizures and presence of HS. Gender ratio, age, duration of epilepsy and seizure frequency were calculated for each of the four groups. Final HDM-LD surface maps of the right and left TLE groups were compared to define differences in subregional hippocampal involvement within the groups.
Results: There were no significant differences in comparisons of the left TLE (left HS−ve compared with HS+ve) or right TLE (right HS−ve compared with HS+ve) groups with respect to age, duration of epilepsy or seizure severity scores. HDM-LD maps showed accentuated surface changes over the lateral hippocampal surface, in the region of the Sommer sector, in the hippocampi affected by HS. However, HS−ve hippocampi showed maximal surface changes in a different pattern, and did not involve the region of Sommer sector.
Conclusion: We conclude that differences in segmental volume loss between the HS−ve and HS+ve groups are suggestive that the underlying pathophysiology of hippocampal changes in the two groups is different, and not related to chronic seizure duration or severity.
Resumo:
Aligned carbon nanotubes (CNTs) can be readily synthesized on quartz or silicon-oxide-coated Si substrates using a chemical vapor deposition method, but it is difficult to grow them on pure Si substrates without predeposition of metal catalysts. We report that aligned CNTs were grown by pyrolysis of iron phthalocyanine at 1000 °C on the templates created on Si substrates with simple mechanical scratching. Scanning electron microscopy and x-ray energy spectroscopy analysis revealed that the trenches and patterns created on the surface of Si substrates were preferred nucleation sites for nanotube growth due to a high surface energy, metastable surface structure, and possible capillarity effect. A two-step pyrolysis process maintained Fe as an active catalyst.
Resumo:
The self-assembling behavior of a single-chain quaternary ammonium amphiphile bearing azobenzene (C12AzoC6N+) on freshly cleaved mica sheet has been investigated by atomic force microscopy (AFM) method. Confocal microscopic Raman spectra confirm the adsorption of the self-assembled monolayer structure. Ex-situ AFM reveals that C12AzoC6N+ forms branch-like stripes indicating the fusion and reorganization of the micelles during drying in air as the in-situ AFM has revealed that surfactant forms spherical micelles on the mica surface. The nano-sized surface structure is strongly dependent on the change of molecular structure, which resulted from photo-induced isomerization. The nano-sized stripe is quite stable even being annealed at 90 °C for 4 h.
Resumo:
Ultrasonics has the potential to reduce the cost and environmental impact of textile processing. This work investigates the effects of utrasonic irradiation during wool scouring on fibre surface properties and fibre dyeing rate. A range of ultrasonic frequencies were used in the scouring bath to examine the forms of fibre cuticle damage. It was shown that ultrasonically scoured wool underwent some modifications of the fibre surface structure which resulted in a higher rate of dye uptake by the fibres, when compared with the conventionally scoured wool. The lower the ultrasonic frequency the more sever was the cuticle damage to wool during scouring, hence the higher the fibre dye uptake.
Resumo:
Scanning tunneling microscopy (STM) images of 1,10-phenanthroline (PHEN) and dipyrido[3,2-a:2‘,3‘-c]phenazine (DPPZ) on Au(111) are recorded using both in situ and ex situ techniques. The images of PHEN depict regimes of physisorption and chemisorption, whereas DPPZ is only physisorbed. All physisorbed structures are not pitted and fluctuate dynamically, involving aligned (4 × 4) surface domains with short-range (ca. 20 molecules) order for PHEN but unaligned chains with medium-range (ca. 100 molecules) order for DPPZ. In contrast, the chemisorbed PHEN monolayers remain stable for days, are associated with surface pitting, and form a (4 × √13)R46° lattice with long-range order. The density of pitted atoms on large gold terraces is shown to match the density of chemisorbed molecules, suggesting that gold adatoms link PHEN to the surface. For PHEN, chemisorbed and physisorbed adsorbate structures are optimized using plane-wave density-functional theory (DFT) calculations for the surface structure. Realistic binding energies are then obtained adding dispersive corrections determined using complete-active-space self-consistent field calculations using second-order perturbation theory (CASPT2) applied to cluster-interaction models. A fine balance between the large adsorbate−adsorbate dispersive forces, adsorbate−surface dispersive forces, gold ligation energy, and surface mining energy is shown to dictate the observed phenomena, leading to high surface mobility and substrate/surface lattice incommensurability. Increasing the magnitude of the dispersive forces through use of DPPZ, rather than PHEN, to disturb this balance produced physisorbed monolayers without pits and/or surface registration but with much longer-range order. Analogies are drawn with similar but poorly understood processes involved in the binding of thiols to Au(111).
Resumo:
Research on mental models Has a rich tradition in cognitive psychology and the psychology of learning. Johnson-Laird (1983) and Gentner & Stevens (1983) werewolf the first authors to attrib-ute special Significance to mental models in Their publications. Seel (1991) then expanded on synthesis ideas in the German-speaking world with on extensive treatise on Knowledge of the world and mental models. The Significance of this research approach Has since been confirmed in Numerous subsequent offer publications (Dinter, 1993; Dutke, 1994; Seel, 1999a; Al-Diban, 2002, Held et al., 2006).In the present study, I would like to Contribute to this discussion from a Methodological per-Spective. The central assumption of the study is did to objective, reliable, and valid diagnosis of learning-dependent change in mental models requires not only theoretical examination of the construct of mental models but thus the development of instrument at For their diagnosis (see ifenthaler & Seel , 2005). The newly developed SMD technology Enables the automated and com-puter-aided diagnosis of externalized models independent of content domain. The externalized models are Diagnosed on three levels, each with a different focus.The central research question as to Whether, and if so how, mental models change in the course of the learning process is Investigated in three experimental studies (N = 106). The longi-tudinal design of the studies Enables a precise diagnosis across a total of seven points of meas-urement. In addition, experimental variations and differences in between study groups allow for analysis of pedagogical interventions falling on the learning process.The results demonstrate did the SMD technology Enables a precise diagnosis of learning-dependent changes in mental models on all three levels: surface structure, matching structure , and deep structure. It was Possible in the three experimental studies to detect a learning-dependent change in mental models on the relational and the structural level. Additionally, the semantic structure of the externalized models Proved to be more Closely similar to the explanation model than to the expert model.The study Concludes with a discussion of the empirical findings and a research outlook Which CLEARLY demarcates Their Range of application. Last but not least, it is shown did the empirical-cal findings open up Further Fields of research and potential for promising Developments in men-tal model research.
Resumo:
Metal-air batteries are a well-established technology that can offer high energy densities, low cost and environmental responsibility. Despite these favourable characteristics and utilisation of oxygen as the cathode reactant, these devices have been limited to primary applications, due to a number of problems that occur when the cell is recharged, including electrolyte loss and poor efficiency. Overcoming these obstacles is essential to creating a rechargeable metal-air battery that can be utilised for efficiently capturing renewable energy. Despite the first metal-air battery being created over 100 years ago, the emergence of reactive metals such as lithium has reinvigorated interest in this field. However the reactivity of some of these metals has generated a number of different philosophies regarding the electrolyte of the metal-air battery. Whilst much is already known about the anode and cathode processes in aqueous and organic electrolytes, the shortcomings of these electrolytes (i.e. volatility, instability, flammability etc.) have led some of the metal-air battery community to study room temperature ionic liquids (RTILs) as non-volatile, highly stable electrolytes that have the potential to support rechargeable metal-air battery processes. In this perspective, we discuss how some of these initial studies have demonstrated the capabilities of RTILs as metal-air battery electrolytes. We will also show that much of the long-held mechanistic knowledge of the oxygen electrode processes might not be applicable in RTIL based electrolytes, allowing for creative new solutions to the traditional irreversibility of the oxygen reduction reaction. Our understanding of key factors such as the effect of catalyst chemistry and surface structure, proton activity and interfacial reactions is still in its infancy in these novel electrolytes. In this perspective we highlight the key areas that need the attention of electrochemists and battery engineers, in order to progress the understanding of the physical and electrochemical processes in RTILs as electrolytes for the various forms of rechargeable metal-air batteries.
Resumo:
The contact load-bearing response and surface damage resistance of multilayered hierarchical structured (MHSed) titanium were determined and compared to monolithic nanostructured titanium. The MHS structure was formed by combining cryorolling with a subsequent Surface Mechanical Attrition Treatment (SMAT) producing a surface structure consisted of an outer amorphous layer containing nanocrystals, an inner nanostructured layer and finally an ultra-fine grained core. The combination of a hard outer layer, a gradual transition layer and a compliant core results in reduced indentation depth, but a deeper and more diffuse sub-surface plastic deformation zone, compared to the monolithic nanostructured Ti. The redistribution of surface loading between the successive layers in the MHS Ti resulted in the suppression of cracking, whereas the monolithic nanograined (NG) Ti exhibited sub-surface cracks at the boundary of the plastic strain field. Finite element models with discrete layers and mechanically graded layersrepresenting the MHS system confirmed the absence of cracking and revealed a 38% decrease in shear stress in the sub-surface plastic strain field, compared to the monolithic NG Ti. Further, the mechanical gradation achieves a more gradual stress distribution which mitigates the interface failure and increases the interfacial toughness, thus providing strong resistance to loading damage. © 2014 Elsevier Ltd.
Resumo:
Activated carbon (AC) prepared from luffa sponge was firstly used as an adsorbent to remove Cr(VI) from aqueous solution. The Cr(VI) adsorption behaviors of AC under different conditions, including initial Cr(VI) concentration, quantity of AC, solution pH, and temperature were investigated. The optimal conditions for adsorption of Cr(VI) by AC were pH = 1, initial Cr(VI) concentration = 80 mg/L, T = 303 K, and AC content = 1.6 g/L. The adsorption kinetics could be described by the pseudo-second-order model. Fourier transform infrared spectroscopy was used to investigate the sorption mechanism. Some functional groups such as C–O and O–H were formed on the carbon surface, which could then react with Cr(VI). The surface structure of AC before and after adsorption was analyzed by scanning electronic microscopy. Adsorbed ions choked some of the pores in AC after adsorption. The Brunauer–Emmett–Teller surface area and average pore size of the AC were 834.13 m2/g and 5.17 nm, respectively. The maximum adsorption of Cr(VI) by AC was 149.06 mg/g, which makes AC prepared from luffa sponge promising for removing Cr(VI) from wastewater.
Resumo:
The efficacy of ionic liquids (ILs) as lubricant additives to a model base oil has been probed at the nanoscale and macroscale as a function of IL concentration using the same materials. Silica surfaces lubricated with mixtures of the IL trihexyl(tetradecyl)phosphonium bis(2,4,4-trimethylpentyl)phosphinate and hexadecane are probed using atomic force microscopy (AFM) (nanoscale) and ball-on-disc tribometer (macroscale). At both length scales the pure IL is a much more effective lubricant than hexadecane. At the nanoscale, 2.0 mol% IL (and above) in hexadecane lubricates the silica as well as the pure IL due to the formation of a robust IL boundary layer that separates the sliding surfaces. At the macroscale the lubrication is highly load dependent; at low loads all the mixtures lubricate as effectively as the pure IL, whereas at higher loads rather high concentrations are required to provide IL like lubrication. Wear is also pronounced at high loads, for all cases except the pure IL, and a tribofilm is formed. Together, the nano- and macroscales results reveal that the IL is an effective lubricant additive - it reduces friction - in both the boundary regime at the nanoscale and mixed regime at the macroscale.
Resumo:
Carbon nanotube (CNT) deposition onto carbon fibre resulting in hybrid surface structures with various morphologies were successfully carried out using electrospray technique. In terms of tensile testing and Weibull analysis this process did not degrade fibre mechanical properties. When incorporated into composites, the interfacial shear strength (IFSS), as measured by single fibre fragmentation testing, increased by up to 124%. Experimental work was carried out to develop a deeper understanding of the interfacial reinforcing mechanism. Contact angle measurements demonstrated that the CNT deposition resulted in good wettability by the resin. Significant increases in roughness, friction and surface area were also found after CNT deposition, especially for the sample prepared using the parameter of 20 kV/10 cm at 100 °C. Surface energy analysis revealed that an increase in the dispersive surface energy due to the CNTs likely contributed to the improvement of interaction between fibre and matrix. Fractographic analysis revealed that the length of fibre pull-out and the size of cracks between the fibre and matrix were markedly decreased in the hybrid CNT surface structure, indicating that the stress transfer and interfacial shear strength have been improved. Finally, the potential for further improvement in interfacial composite properties by this approach was assessed.