On the impact of second phase particles on twinning in magnesium alloys

Deformation twinning is an important deformation mode in magnesium alloys. Despite this, little is known on the extent to which the stress for twinning can be altered by a dispersion of second phase particles. The current paper presents a series of findings on the role of differently shaped particles on both the stress required for twinning and the characteristics of the twins that form. It is shown that plate shaped particles are, as one might expect, an effective strengthener to {10-12} twinning. When precipitate plates form on the basal planes, the relative hardening of basal slip is minor in comparison to that seen for twinning. This provides opportunity for the alloy designer to control the apparent critical resolved shear stresses (CRSS) for the different deformation modes. Possible sources for the hardening of twins are discussed.

Mixing layer oscillations for a submerged horizontal wall-jet

Measurements of the horizontal velocity component were made for a horizontal wall-jet emanating from a submerged sluice gate forming one side of a large flow compartment. The existence of large-scale vortex structures was quantified by spectral analysis of the velocity measurements taken at various distances from the floor of the flow compartment, for different measurement stations from the jet exit. Close to the jet exit, the spectra of the velocity measurements within the potential core exhibit multiple peaks. Further downstream, the spectra are more defined and peak at the same frequency, irrespective of whether the measurements were made within the potential core or the mixing layer. The spectral peak corresponds to the passage frequency of large-scale vortex structures. Downstream of the potential core, the peak frequencies of the velocity spectra increase as the measurement location was moved towards the floor of the flow compartment. The increase in peak frequencies is attributed to fluctuations associated with the wall boundary layer. Predictions of the mixing layer instabilities were made using linear stability analysis. The predictions are in good agreement with the observed vortex shedding frequencies in the mixing layer

Single layer lead iodide : computational exploration of structural, electronic and optical properties, strain induced band modulation and the role of spin-orbital-coupling

Graphitic like layered materials exhibit intriguing electronic structures and thus the search for new types of two-dimensional (2D) monolayer materials is of great interest for developing novel nano-devices. By using density functional theory (DFT) method, here we for the first time investigate the structure, stability, electronic and optical properties of monolayer lead iodide (PbI2). The stability of PbI2 monolayer is first confirmed by phonon dispersion calculation. Compared to the calculation using generalized gradient approximation, screened hybrid functional and spin-orbit coupling effects can not only predicts an accurate bandgap (2.63 eV), but also the correct position of valence and conduction band edges. The biaxial strain can tune its bandgap size in a wide range from 1 eV to 3 eV, which can be understood by the strain induced uniformly change of electric field between Pb and I atomic layer. The calculated imaginary part of the dielectric function of 2D graphene/PbI2 van der Waals type hetero-structure shows significant red shift of absorption edge compared to that of a pure monolayer PbI2. Our findings highlight a new interesting 2D material with potential applications in nanoelectronics and optoelectronics.

Immunostimulatory polysaccharides from Chlorella pyrenoidosa. A new galactofuranan. Measurement of molecular weight and molecular weight dispersion by DOSY NMR.

Fractionation of the hot water extract of Chlorella pyrenoidosa was performed using a combination of ethanol precipitation, size exclusion chromatography, and anion exchange chromatography. One fraction contained a new polysaccharide, and this compound was shown to be a 1→2-linked β-d-galactofuranan from its 1D and 2D 1H and 13C NMR spectra, with a molecular weight of 15 kDa from DOSY NMR measurements. A number of other fractions were shown to have the same repeating unit as the previously identified arabinogalactan. However, arabinogalactans from different fractions were shown by DOSY NMR to have different molecular weights, which ranged from 27 to 1020 kDa. Agreement with molecular weights measured for some of these fractions by SEC-MALS was very good, further confirming the relationship established by Viel et al. between molecular weights of neutral polysaccharides and self-diffusion coefficients. The smaller molecular weight polysaccharides, the galactofuranan and the 27 and 50 kDa arabinogalactans, were shown to be close to monodisperse by analysis of the distributions of the self-diffusion coefficients for the polymers. The larger arabinogalactans had considerable variation in their molecular weights (188 ± 109 kDa and 1020 ± 370 kDa). Only the two larger arabinogalactans showed immunostimulatory activity.

Use of high resolution digital multi-spectral imagery to assess the distribution of disease caused by Phytophthora cinnamomi on heathland at Anglesea, Victoria

Disease caused by the soilborne plant pathogen Phytophthora cinnamomi causes long-term floristic and structural changes in native vegetation communities in Australia. Key components of the management of this disease are to know where it occurs and the rate at which it spreads. The distribution of P. cinnamomi has generally been assessed as locality points of infestation and mapping the extent of diseased vegetation in any area is difficult and costly. This study was undertaken in P. cinnamomi-infested heathland communities in southern Victoria, Australia, where the symptoms of P. cinnamomi arise as a mosaic within healthy vegetation. We investigated the potential to improve the efficiency and effectiveness of mapping and monitoring vegetation affected by P. cinnamomi using digital multi-spectral imaging. This technique was developed for the purposes of monitoring vegetation and provides a single, seamless ortho-rectified digital image over the total area of interest. It is used to spatially quantify small differences in the characteristics of vegetation. In this study, the symptoms of disease caused by P. cinnamomi infestation were related to differences in the imagery and were used to map areas of infestation. Comparison of the digital multi-spectral imaging indications with on-ground observations gave moderate accuracy between the datasets (κ = 0.49) for disease and healthy indications. This study demonstrates the ability of the technique to determine disease extent over broad areas in native vegetation and provides a non-invasive, cost effective tool for management.

Improved 2D‐HPLC of red wine by incorporating pre‐process signal‐smoothing algorithms

Twomultidimensional HPLC separations of an Australian red wine are presented, >70% of the available separation space was used. A porous graphitic carbon (PGC) stationary phase was used as the first dimension in both separations with both RP core–shell and hydrophilic interaction chromatography fully porous columns used separately in the second dimension. To overcome peak analysis problems caused by signal noise and low detection limits, the data were pre-processed with penalised least-squares smoothing. The PGC × RP combination separated 85 peaks with a spreading angle of 71 and the PGC × hydrophilic interaction chromatography separated 207 peaks with a spreading angle of 80. Both 2D-HPLC steps were completed in 76 min using a comprehensive stop-and-go approach. A smoothing step was added to peak-picking processes and was able to greatly reduce the number of false peaks present due to noise in the chromatograms. The required thresholds were not able to ignore the noise because of the small magnitude of the peaks; 1874 peaks were located in the non-smoothed PGC × RP separation that reduced to 227 peaks after smoothing was included.

An improved understanding of the dispersion of multi-walled carbon nanotubes in non-aqueous solvents

The homogeneous and stable dispersion of carbon nanotubes (CNTs) in solvents is often a prerequisite for their use in advanced materials. Dispersion procedures, reagent concentration as well as the interactions among reagent, defective CNTs and near-perfect CNTs will affect the resulting CNT dispersion properties. This study, for the first time, presents a detailed comparison between two different approaches for dispersing CNTs. The results enhance our understanding of the interactions between surfactant, defective CNTs and near-perfect CNTs and thus provide insight into the mechanism of CNT dispersion. Dispersions of "as-produced" short multi-walled carbon nanotubes (MWCNTs) in N,N-dimethylformamide were prepared by two different surfactant (Triton X-100) assisted methods: ultrasonication and ultrasonication followed by centrifugation, decanting the supernatant and redispersing the precipitate. Visual observation and UV-visible spectroscopy results showed that the latter method produce a more stable dispersion with higher MWCNT content compared to dispersions produced by ultrasonication alone. Transmission electron microscopy and Raman spectroscopic investigations revealed that the centrifugation/ decanting step removed highly defective nanotubes, amorphous carbon and excess surfactant from the readily re-dispersible near-perfect CNT precipitate. This is contrary to other published findings where the dispersed MWCNTs were found in the supernatant. Thermogravimetric analysis showed that 95 % of Triton X-100 was removed by centrifugation/decanting step, and the remainder of the Triton X-100 molecules is likely randomly adsorbed onto the MWCNT surface. Infrared spectral analysis suggests that the methylene groups of the polyoxyethylene (aliphatic ether) chains of the residual Triton X-100 molecules are interacting with the MWCNTs. © 2014 Springer Science+Business Media.

Neural signal analysis by landmark-based spectral clustering with estimated number of clusters

Spike sorting plays an important role in analysing electrophysiological data and understanding neural functions. Developing spike sorting methods that are highly accurate and computationally inexpensive is always a challenge in the biomedical engineering practice. This paper proposes an automatic unsupervised spike sorting method using the landmark-based spectral clustering (LSC) method in connection with features extracted by the locality preserving projection (LPP) technique. Gap statistics is employed to evaluate the number of clusters before the LSC can be performed. Experimental results show that LPP spike features are more discriminative than those of the popular wavelet transformation (WT). Accordingly, the proposed method LPP-LSC demonstrates a significant dominance compared to the existing method that is the combination between WT feature extraction and the superparamagnetic clustering. LPP and LSC are both linear algorithms that help reduce computational burden and thus their combination can be applied into realtime spike analysis.

Development of a sustained release solid dispersion using swellable polymer by melting method

PURPOSE: This study is to design a sustained release solid dispersion using swellable polymer by melting method. METHODS: Polyethylene glycol 6000 (PEG 6000) and hydroxypropyl methylcellulose 4000 (HPMC 4000) were used in solid dispersion for not only enhancing drug dissolution rate but also sustaining drug release. HPMC 4000 is a common swellable polymer in matrix sustained release dosage form, but could not be used in preparation of solid dispersion by melting method. However, the current study utilized the swelling capability of HPMC 4000 accompanied by the common carrier PEG 6000 in solid dispersion to accomplish the goal. RESULTS: While PEG 6000 acted as a releasing stimulant carrier and provided an environment to facilitate the swelling of HPMC 4000, this swellable polymer could act as a rate-controlling agent. This greatly assisted the dissolution enhancement by changing the crystalline structure of drug to more amorphous form and creating a molecular interaction. CONCLUSIONS: These results suggested that this useful technique can be applied in designing a sustained release solid dispersion with many advantages.