Use of ionic liquids as electrolytes in electromechanical actuator systems based on inherently conducting polymers

The use of ionic liquids (ILs) as electrolytes for electromechanical actuators based on polypyrroles (PPy's) is described. The composition of the electrolytes has a significant effect on the electrochemical properties of the PPy actuator and subsequently on actuator performance, improving cycle life and strain generated. The actuator performance in ionic liquid electrolytes is significantly better than that in traditional organic and aqueous electrolytes.

Conducting polymers with fibrillar morphology synthesized in a biphasic ionic liquid/water system

The synthesis of poly(pyrrole), poly(terthiophene), and poly(3,4-ethylenedioxythiophene) with unusual fibrillar morphologies has been achieved by chemical polymerization in a biphasic ionic liquid/water system. Use of aqueous gold chloride as the oxidant, with the monomers dissolved in a hydrophobic ionic liquid, allows the polymerization to occur at the ionic liquid/water interface. The resultant conducting polymer fibrils are, on average, 50−100 nm wide and can be thousands of nanometers long. The polymers produced in this ionic liquid system are compared to those synthesized in a biphasic chloroform/water system.

High current density and drift velocity in templated conducting polymers

Conducting polymers prepared by a templated vapour phase polymerisation process involving solid phase transition metal complexes are found to produce polymers with charge carriers that exhibit maximum drift velocity in the range of 1 m/s. This super-mobility seems to be related to a high degree of ordering in the materials as evidenced by the X-ray diffraction data. This may result from a templated polymerisation process. The high mobility manifests itself as a capacity to sustain very high current densities (>10000 A/cm2); such high current densities are of importance in thin film conductor applications.

Synthesis and characterization of soluble conducting polymers

Although conducting polymers have various potential applications, lack of solubility is an impediment in their direct application to material surfaces. Synthesis of alkyl pyrrole monomers and subsequent polymerization into soluble conducting polymers are aimed as alternatives to conventional methods of application of conducting polymers on substrates. Alkyl chains are attached to a pyrrole ring to produce solubility in the resulting conducting polypyrroles, which allow direct application of conductive polymer emulsions to any desired surface. Friedel-Crafts acylation of the tosyl-protected pyrrole provides high yields of the 3-acylated product. The conductivity values of poly-3- and 3, 4-substituted pyrroles are generally less than the unmodified polypyrrole. Increasingly bulkier groups attached to the pyrrole means lower conductivity of the resultant polymer. As the carbon chain length attached to the 3-position of pyrrole increases, the solubility also increases. However, the magnitude of change in conductivity of films and pellets of soluble conducting polypyrroles over the alkyl range is not significant.

Methods of coating textiles with soluble conducting polymers

Soluble conducting alkyl polypyrrole polymers have been applied by either chemical polymerization of the 3-alkyl monomers or direct application of polymer emulsion to the surface. Solution, vapor and spray polymerization methods of coating poly(3-alkylpyrroles) to the surface of woven wool fabrics are explored. Conductive textile samples have also been prepared by applying emulsions of soluble prepolymerized 3-alkylpyrrole to the fabric surface. Direct applications of a conductive paint to the textile surface eliminate the exposure of the substrate to damaging oxidizing agents which allow the coating of more sensitive and delicate substrates. All textiles produced are tested for abrasion resistance and conductivity. For alkyl polypyrrole coated fabrics, the optimum carbon chain lengths are between n=10 and n=14, which result in optimum values of conductivity and solubility. The darkness of the tone is inversely related to the surface resistivity of the resulting conductive fabric. Therefore, deep black coatings have low resistivity whereas light gray coatings on a white fabric surface have higher surface resistivity. Longer alkyl chains result in higher surface resistivity in fabrics. The conductive coating of poly(3-decanylpyrrole) on the textile surface has a better abrasion resistance compared to that of an unsubstituted polypyrrole coating.

Soluble poly-3-alkylpyrrole polymers on films and fabrics

Conductive textiles with specific properties can be produced by the chemical polymerisation of a range of 3-alkylpyrroles in the presence of textiles. The morphologies of these coatings are altered from the traditional conductive coatings. Comparison using a SEM reveals substantial differences.

Development of a cooling fabric from conducting polymer coated fibres: proof of concept

It is supposed that there should be a thermal electric effect if a dc current is applied across two dissimilar conducting polymers, similar to so called “Peltier effect” in metals or semiconductors. However, this hypothesis has not been tested on conducting polymers and using these materials to make cooling fabrics has never been attempted before. Polypyrrole coated fabrics were used to test the hypothesis in this preliminary study. Seebeck and the Peltier effects were proven to exist. However, thermoelectricity effect between two conducting polymer coated fabric samples was only about 10 μV/°C. Cooling effect by conductive polymer powder was achieved but performance was unsteady due to electrical degradation of the conducting polymer. Nevertheless, the concept was demonstrated and the development of a cooling fabric is possible.

Application of soluble poly (3-alkylpyrrole) polymers on textiles

Soluble conducting poly(3-decanylpyrrole) was directly applied to textiles as a nanoparticle emulsion, using a variety of techniques including hand-brushing, dipping and spray painting. These coatings were compared to those formed by chemical polymerization of 3-decanylpyrrole on the surface of the textile by solution, using vapor and spray polymerization methods. The coating formed using chemical polymerization methods had lower surface resistivity than that formed by direct application of a soluble polymer.

It was observed that applied coatings of poly(3-decanylpyrrole) showed a smoother surface morphology with a more even dispersion compared to those formed by chemical methods.

Conjugated polymers for light-emitting applications

Processable conjugated polymers such as those shown in the Figure are highly desirable for applications in, for example, light emitting devices, especially electrochemical light-emitting cells. Here recent progress in Australia on the synthesis and device applications of such polymers is reviewed and the possibility of tuning the emitted color via an intercalation-induced conformational change of the polymer backbone is examined.

Novel conducting polymer films and coated textiles

This research developed non-hazardous methods for coating wool with conductive polymers for thermal and anti-static clothing. Conductive polymers are black in colour, thus the synthesis of new conductive polymers was required to produce coloured or fluorescent conductive textile. Cross-linked conductive polymers were also synthesised to increase their durability.