A survey on mechanisms and critical parameters on solidification of selective laser melting during fabrication of Ti-6Al-4V prosthetic acetabular cup

Additive Manufacturing (AM) includes a range of approaches that correlate with computer aided design (CAD) and manufacturing by fabrication via precise layers and is a promising method for the production of medical tools. In this study, different aspects and mechanisms of solidification for curved surfaces based on equilibrium at curved interfaces, Monge patch, interfacial and Gibbs energy will be discussed. Also, the effect of capillarity, geometry, substrate temperature, cooling rate and scanning parameters in the solidification of a prosthetic acetabular cup (PAC) using selective laser melting (SLM) is analysed. The contributions of this work are analysing solidification and effective factors in this process to produce parts with a higher quality and mechanical properties such as strength, strain, porosity, relative density and hardness. Results indicate that due to the surface to volume (S/V) ratio, and the increasing effect of the radius on Monge patch, thermal stresses and surface forces are more prevalent on outer surfaces. Moreover, solidification and mechanical properties are related to capillarity, geometry, substrate temperature, cooling rate, scanning power and speed. The results also indicate the interaction of solute diffusion and heat transfer with interatomic forces in large S/V ratio and at small scales tend to improve solidification.

An improved static model for tool deflection in machining of Ti–6Al–4V acetabular shell produced by selective laser melting

Tool deflection during milling operation leads to dimensional error, decreasing surface quality and increasing rejection rate. In this study, tool deflection during the milling of the inner surfaces of Ti–6Al–4V prosthetic acetabular shell produced by selective laser melting (SLM) was modelled. The first purpose of this research is to provide a general static cutting tool deflection model for ball nose cutters where deviation of machine components and tool holder are so small as to be considered negligible. This is because the values of machine component and tool holder deflection were lower than standard tolerances (10 μm) and found to be lower than 1/15 of tool deflection. The second and third objectives of this work involve calculating contact surfaces by determining workpiece and tool geometry and choosing second moment of inertia using a novel cross section method (CSM). Static models for three quasi-analytical methods (QAM) that are simple cantilever beam model (SCBM), two-section model (TWSM) and our three section model (THSM) are presented. THSM showed high accuracy which was validated by 3D finite element method (FEM3D) and experimental measurements. The accuracy of tool deflection calculation using THSM by computing, shank, flute and ball head deflection and also utilizing CSM to determine second moment of inertia showed notable improvements.

Tool wear and surface integrity analysis of machined heat treated selective laser melted Ti-6Al-4V

In this study, the tool wear and surface integrity during machining of wrought and Selective LaserMelted (SLM) titanium alloy (after heat treatment) are studied. Face turning trails were carried out onboth the materials at different cutting speeds of 60,120 and 180 m/min. Cutting tools and machinedspecimens collected are characterized using scanning electron microscope, surface profiler and opticalmicroscope to study the tool wear, machined surface quality and machining induced microstructuralalterations. It was found that high cutting speeds lead to rapid tool wear during machining of SLMTi-6Al-4V materials. Rapid tool wear observed at high cutting speeds in machining SLM Ti-6Al-4Vresulted in damaging the surface integrity by 1) Deposition of chip/work material on the machinedsurface giving rise to higher surface roughness and 2) Increasing the depth of plastic deformationon the machined sub surface.

Metallurgical and machinability characteristics of wrought and selective laser melted Ti-6Al-4V

This research work presents a machinability study between wrought grade titanium and selective laser melted (SLM) titanium Ti-6Al-4V in a face turning operation, machined at cutting speeds between 60 and 180 m/min. Machinability characteristics such as tool wear, cutting forces, and machined surface quality were investigated. Coating delamination, adhesion, abrasion, attrition, and chipping wear mechanisms were dominant during machining of SLM Ti-6Al-4V. Maximum flank wear was found higher in machining SLM Ti-6Al-4V compared to wrought Ti-6Al-4V at all speeds. It was also found that high machining speeds lead to catastrophic failure of the cutting tool during machining of SLM Ti-6Al-4V. Cutting force was higher in machining SLM Ti-6Al-4V as compared to wrought Ti-6Al-4V for all cutting speeds due to its higher strength and hardness. Surface finish improved with the cutting speed despite the high tool wear observed at high machining speeds. Overall, machinability of SLM Ti-6Al-4V was found poor as compared to the wrought alloy.

Microstructure and mechanical properties of wrought and additive manufactured Ti-6Al-4V cylindrical bars

Titanium alloys are widely used in various engineering design application due to its superior material properties. The traditional manufacturing of titanium products is always difficult, time consuming, high material wastage and manufacturing costs. Selective laser melting (SLM), an additive manufacturing technology has widely gained attention due to its capability to produce near net shape components with less production time. In this technical paper,microstructure,chemical composition,tensile properties and hardness are studied for the wrought and additive manufactured SLM cylindrical bar. Microstructure,mechanical properties and hardness were studied in both the longitudinal and transverse directions of the bar to study the effect of orientation. It was found that additive manufactured bar have higher yield strength, ultimate tensile strength and hardness than the wrought bar. For both conventional and SLM test samples, the yield strength, ultimate tensile strength and hardness was found to be high in the transverse direction. The difference in the properties can be attributed to the difference in microstructure as a result of processing conditions. The tensile fracture area was quantified by careful examination of the fracture surfaces in the scanning electron microscope.

Additive manufacturing in the cycling industry: mainstream or gimmick?

INTRODUCTION. Additive manufacturing (AM) for various industries has been trailed, prototyped and used in limited production runs (Gibson, 2015). But considering additive manufacturing with metallic materials has been around for over 15 years the penetration into an industry such as cycling that values customisation and progressive design techniques has been quite limited. This case study looks at the potential of and why additive manufacturing has not progressed from concept development and prototyping into production and mainstream. Selective Laser Melting (SLM) additive manufacturing systems mainly use Stainless Steel 316 (SS316) and Titanium 6Al.4V (Ti64) as a baseline material; both these materials are extremely common in the custom and high volume bike industries. For the purposes of this article we will focus on smaller custom bike manufacturers who are typically more agile and open to high levels of customisation in their products. The study finds that whilst a high number of companies will experiment and prototype with additive manufacturing there is little evidence that the design and development process translates to ongoing production for sale to the consumer, this could be due to knowledge of design and fabrication techniques.

Laser-induced site-selective silver seeding on polyimide for electroless copper plating

Ag particles were generated on Ag+-doped polyimide film by laser direct writing, followed by selective copper deposition using the metallic silver particles as seeds. Laser irradiation caused in situ reduction and agglomeration of silver on the polyimide film. The copper lines were less uniform and compact with higher scanning velocity and the width of the deposited copper line could reach 25 mu m. Equations of the relationship between scanning velocity and connectivity of the deposited copper patterns have been derived. The process was characterised by AFM, XPS, SEM, and semiconductor characterisation system.

Fabrication of meso-porous sintered metal thin films by selective etching of silica based sacrificial template

 Meso-porous metal materials have enhanced surface energies offering unique surface properties with potential applications in chemical catalysis, molecular sensing and selective separation. In this paper, commercial 20 nm diameter metal nano-particles, including silver and copper were blended with 7 nm silica nano-particles by shear mixing. The resulted powders were cold-sintered to form dense, hybrid thin films. The sacrificial silica template was then removed by selective etching in 12 wt% hydrofluoric acid solutions for 15 min to reveal a purely metallic meso-porous thin film material. The impact of the initial silica nano-particle diameter (7–20 nm) as well as the sintering pressure (5–20 ton·m−2) and etching conditions on the morphology and properties of the final nano-porous thin films were investigated by porometry, pyknometery, gas and liquid permeation and electron microscopy. Furthermore, the morphology of the pores and particle aggregation during shear mixing were assessed through cross-sectioning by focus ion beam milling. It is demonstrated that meso-pores ranging between 50 and 320 nm in average diameter and porosities up to 47% can be successfully formed for the range of materials tested.