Microwave dielectric properties of PTFE/rutile nanocomposites

The effects of nano-size rutile filler on the microwave dielectric properties of PTFE composites were investigated and the results were compared with that of micron size rutile filled composites. Nano-size rutile powder was prepared through sol–gel route and the filled PTFE composites were fabricated through SMECH process. Different characterization techniques such as powder X-ray diffraction, SEM, BET, TEM and TG/DSC were employed to analyze the nature of ceramic filler. The dielectric properties of filled composites were evaluated at microwave frequency region using waveguide cavity perturbation technique. Different theoretical models have been employed to predict the variation of dielectric constant with respect to filler loading. The moisture absorption characteristics of nano-rutile filled PTFE composites were measured as per IPC-TM-650 2.6.2 standards. Composites show high dielectric constant at X-band frequency region with relatively high loss tangent compared to micron size counterpart.

Photocatalytic degradation of dyes in wastewater using TiO2/UV in a flat-plate reactor

The photocatalyst TiO₂ with UV irradiation was used to degrade dyes in textile effluent in a flat-plate photoreactor. A test system was built with the reactor area of 1 x 0.3m2, UV light of six 36W-blacklight. TiO₂ powder P25 with BET surface area 50±15m2/g, average primary particle size 21 nm, purity> 99.5% and content of 83.9% anatase and 16.1 % rutile was used as the photocatalyst. A number of dyes commonly present in dyeing wastewater were tested in this study. The different operating parameters, such as dosage of photocatalyst, the structure of the reactor, flow rates through the flat-plate reactor, UV radiation intensity and tilted angle of the reactor, were investigated. The results showed that the photocatalytic process could efficiently remove most of the colour contained in the dyeing wastewater. It was experimentally observed that first-order kinetics was adequate for characterising the process. The flow rate and the tilted angle had some influence on the film thickness of the fluid in the reactor and the empirical correlation between the film thickness of the fluid and these two parameters was developed. The photoreaction rate was mainly determined by the film thickness of the fluid on the reactor surface and the dosage of the photocatalyst. Optimum operating parameters of the system were found to be at the film thickness of about 1.4mm and a TiO₂ dosage of 1 gIL. The higher the UV intensity, the faster the reaction rate was. The results of these experiments showed that this method has the great potential for colour removal from wastewater at commercial scale.

To overcome the common difficulty of separating the used TiO₂ suspension after treatment precipitation followed with filtration was used in this study to determine the separation efficiencies. On the other hand, TiO₂ in a small pillar shape was also studied for photocatalytic degradation of textile dye effluent. The pillar pellet was made in Oegussa Company, Germany ranging from 2.5 to 5.3mm long and with a diameter of 3.7mm. It was almost pure TiO₂ (83.2% anatase and 16.8% rutile), with a S-content of <20 ppm and a CI content of the order of 0.1 wt. %. No further elements are present in contents above 0.05 wt.%. The TiO₂ pillars were placed on the flat-plate reactor that was divided by the rectangular slots and irradiated under UV light when the treated solution went through the reactor. Four dyes and their mixtures were tested. The results showed that the photocatalytic process under this configuration efficiently remove the colour from textile dyeing effluent, and pillar shape TiO₂ photocatalyst was not dissolved in water and very easy to be separated from solution, enabling it to be reused many times. The first-order kinetics was adequate for characterising the photocatalytic degradation process and the photocatalytic performance was comparable to TiO₂ powder. It is believed that the TiO₂ pellet would be a preferable form of photocatalyst in applications for textile effluent treatment process, and other wastewater treatment processes.

Titanium oxide nanorods extracted from ilmenite sands

One dimensional titanium oxides (TiO2) nanorods and nanowires have substantial applications in photocatalytic, nanoelectronic, and photoelectrochemical areas. These applications require large quantities of materials and a production technique suitable for future industry fabrication. We demonstrate here a new method for mass production of TiO2 nanorods from mineral ilmenite sands (FeTiO3). In this process, powder mixtures of ilmenite and activated carbon were first ball milled; the milled samples were then heated twice at two different temperatures. First high-temperature annealing produced metastable titanium oxide phases, and subsequent second low-temperature annealing in N2-5%H2 activates the growth of rutile nanorods. This solid-state growth process allows large-quantity production of rutile nanorods.

One-dimensional growth of TiO2 nanorods from ilmenite sands

Growth mechanisms of TiO₂ nanorods synthesized from mineral ilmenite using ball milling and annealing method have been systematically investigated. Two annealing processes are needed to grow the nanorods. The heating rate and gaseous environment in the first annealing step are critical to the formation of intermediate phases; these and the annealing atmosphere in the second heating play very important roles in nanorod growth. One-dimensional growth of the nanorods induced by low-temperature annealing in nitrogen plus hydrogen is possibly driven by atom vacancy diffusion in addition to surface diffusion.

Phase-structure effects of electrospun TiO2 nanofiber membranes on As(III) adsorption

TiO2 nanofibers (NFs) with different phases such as amorphous, anatase, mixed anatase?rutile, and rutile have been prepared by combining the electrospinning technique with the subsequent process of heat treatment or acidic-dissolution method. The obtained NFs are characterized by a Fourier transform infrared spectrometer (FT-IR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and N2 adsorption?desorption isotherm measurements. Phase structure effects of electrospun TiO2 NFs on As(III) adsorption behaviors have been investigated. The results showed a significant effect of the phase structures of TiO2 NFs on As(III) adsorption rates and capacities. Amorphous TiO2 NFs have the highest As(III) adsorption rate and capacity in the investigated samples, which can be attributed to its higher surface area and porous volume. This research provides a simple and low-cost method for phasecontrolled fabrication of TiO2 NFs and application for effective removal of arsenic from aqueous solution.

Binding affinities of amino acid analogues at the charged aqueous titania interface : implications for titania-binding peptides

Despite the extensive utilization of biomolecule-titania interfaces, biomolecular recognition and interactions at the aqueous titania interface remain far from being fully understood. Here, atomistic molecular dynamics simulations, in partnership with metadynamics, are used to calculate the free energy of adsorption of different amino acid side chain analogues at the negatively-charged aqueous rutile TiO2 (110) interface, under conditions corresponding with neutral pH. Our calculations predict that charged amino acid analogues have a relatively high affinity to the titania surface, with the arginine analogue predicted to be the strongest binder. Interactions between uncharged amino acid analogues and titania are found to be repulsive or weak at best. All of the residues that bound to the negatively-charged interface show a relatively stronger adsorption compared with the charge-neutral interface, including the negatively-charged analogue. Of the analogues that are found to bind to the titania surface, the rank ordering of the binding affinities is predicted to be "arginine" > "lysine" ≈ aspartic acid > "serine". This is the same ordering as was found previously for the charge-neutral aqueous titania interface. Our results show very good agreement with available experimental data and can provide a baseline for the interpretation of peptide-TiO2 adsorption data.

Improvement of the biomedical properties of titanium using SMAT and thermal oxidation

Titanium and its alloys are excellent candidates for biomedical implant. However, they exhibit relatively poor tribological properties. In this study, a two-step treatment including surface mechanical attrition treatment (SMAT) combined with thermal oxidation process has been developed to improve the tribological properties and biocompatibility of Ti. Ti after two-step treatment shows excellent wear-resistance and biocompatibility among all Ti samples, which can be ascribed to the highest surface energy, well crystallinity of rutile layer on its surface. Overall, the two-step treatment is a prospective method to produce excellent biomedical Ti materials.