We need one district government to be set up to replace other district governments : the beginnings of Provincial Government in Papua New Guinea

Decentralisation, provincial government, and regional autonomy continue as influential factors in Papua New Guinea’s political economy.  The role played in creating PNG’s provincial government system by separatist movements in East New Britain, Bougainville and elsewhere is acknowledged.  However, as the Constitutional Planning Committee (CPC) discovered during its program of consultations with the Papua New Guinean people from 1972 to 1974, there was a strong groundswell around the country for district-level governments.  This article investigates how the CPC stimulated discussion of this issue through its own activities, and how the people in their discussion groups responded to the CPC’s ‘Discussion Paper on Relations Between the Central Government and Other Levels of Government’.

Photocatalytic reduction of carbon dioxide into gaseous hydrocarbon using TiO2 pellets

It has been shown that CO₂ could be transformed into hydrocarbons when it is in contact with water vapour and catalysts under UV irradiation. This paper presents an experimental set-up to study the process employing a new approach of heterogeneous photocatalysis using pellet form of catalyst instead of immobilized catalysts on solid substrates. In the experiment, CO₂ mixed with water vapour in saturation state was discharged into a quartz reactor containing porous TiO₂ pellets and illuminated by various UV lamps of different wavelengths for 48 h continuously. The gaseous products extracted were identified using gas chromatography. The results confirmed that CO₂ could be reformed in the presence of water vapour and TiO₂ pellets into CH₄ under continuous UV irradiation at room conditions. It showed that when UVC (253.7 nm) light was used, total yield of methane was approximately 200 ppm which was a fairly good reduction yield as compared to those obtained from the processes using immobilized catalysts through thin-film technique and anchoring method. CO and H₂ were also detected. Switching from UVC to UVA (365 nm) resulted in significant decrease in the product yields. The pellet form of catalyst has been found to be attractive for use in further research on photocatalytic reduction of CO₂.

Adolescent parenthood : a costly mistake or a search for love?

Family life is changing worldwide and an increasing number of women are choosing single parenthood. Adolescents who become pregnant and early childbearers do not always become pregnant unintentionally; some actively plan pregnancy while others are ambivalent mainly about the timing. This paper reports on a study using an ethnographic approach that explored the mothering experiences of five sole-supporting Australian teenage mothers who had a child over six months of age. It focuses on the story of one of them, a young woman who gave birth at 16 and set up home for herself and her son. Early childbearing is often a response to adverse social conditions such as poverty or homelessness and is not uncommonly chosen by teenage girls from socially deprived backgrounds. Educational and employment opportunities may be limited, whilst motherhood may provide a purpose in life when few other options are possible. Young women who make this choice need comprehensive services to support them in the parenting role, including appropriate health care, welfare and housing benefits, and support in dealing with parenting, a role which they may greatly desire but are not automatically well prepared for.

Corporate liability for workplace deaths and injuries-reflecting on Victoria's laws in the light of the Esso Longford explosion

The purpose of this article is to consider some different legal models for the liability of corporations for the deaths and serious injuries of their employees, with particular emphasis on the law in Victoria.

Two recent developments in Victoria prompt this consideration. First, on 30 July 2001, the Victorian Supreme Court handed down its sentencing decision in the case arising from the explosion on 25 September 1998 at the Longford gas plant operated by Esso Australia Pty Ltd. The decision marked the end of the formal public consideration of a devastating event in Victorian industrial history, which began with the Royal Commission set up on 20 October 1998 to investigate the causes of an explosion in which two workers died and eight others were injured. Second, in early 2002, the Victorian Government failed in its attempt to introduce new criminal offences for corporate employers whose employees are killed or seriously injured at work. In spite of their failure to be passed by the Legislative Council in Victoria, these proposals warrant consideration. They represent a growing trend by policy makers in attempting to address more effectively the question of the liability for deaths and serious injuries of workers to employers who operate through the corporate form.

Using geometric shape variations to create an inverse model for a sheet metal process

The output of the sheet metal forming process is subject to much variation. This paper develops a method to measure shape variation in channel forming and relate this back to the corresponding process parameter levels of the manufacturing set-up to create an inverse model. The shape variation in the channels is measured using a modified form of the point distribution model (also known as the active shape model). This means that channels can be represented by a weighting vector of minimal linear dimension that contains all the shape variation information from the average formed channel.

The inverse models were created using classifiers that related the weighting vectors to the process parameter levels for the blank holder force (BHF), die radii (DR) and tool gap (TG) of the parameters. Several classifiers were tested: linear, quadratic Gaussian and artificial neural networks. The quadratic Gaussian classifiers were the most accurate and the most consistent type of classifier over all the parameters.

Force modelling of the crankshaft pin grinding process.

A force model was developed for crankshaft pin grinding to predict the forces generated during grinding. The force model developed builds on the authors’ previously developed model, which predicted the out-of-roundness in crankshaft pin grinding. The model includes key grinding variables, such as the work removal parameter (WRP), system sti€ ness and Young’s modulus to determine the end forces produced. The model also includes the important geometrical relationships that are unique to this type of grinding. The model was veriŽ ed using an experiential set-up involving sophisticated strain gauge force measurements on a commercial Landis CP grinding machine, with close correlation between the results and the model.

Criminal penalties for contraventions of Part IV of the Trade Practices Act

In 2003 the Dawson Committee, commissioned by the Government, recommended that criminal penalties should be introduced for cartel conduct. The Government accepted this recommendation in principle and set up a working party to consider the implementation difficulties that had been identified in the Dawson Report. Nothing further was heard from the Government until February 2005 when the Government announced that it would introduce criminal penalties for serious cartel conduct. This paper evaluates the Government proposals and makes suggestions for their implementation.

Finite element modelling of metallic tubular crash structures with an explicit code

Numerous experimental studies have been carried out to investigate the collapse of tubular metallic crash structures under axial compression. Some simple theoretical models have been developed but these often assume one type of progressive collapse, which is not always representative of the real situation. Finite Element (FE) models, when further refined, have the potential to predict the actual collapse mode and how it influences the load-displacement and energy absorption characteristics. This paper describes an FE modelling investigation with the explicit code LS−DYNA. An automatic mesh generation programme written by the authors is used to set up shell and solid element tube models. Mesh specification issues and features relating to the contact and friction models are discussed in detail. The crush modes, load-deflection characteristics and energy absorption values found in the simulations are compared with a reasonable degree of correlation to those observed in a physical testing programme; however, improvements are still required.