Energy absorption behaviour of rapidly manufactured carbon/epoxy and glass/polypropylene structures

In this thesis the crashworthiness of composite tubular structures was investigated along with the property structure relationships of a glass/polypropylene material. The energy absorption capacity of tubular structures in a number of different testing configurations was made. Two materials; carbon/epoxy pre-preg and a glass/polypropylene dry pre-preg were investigated.

Bond properties of rubber modified epoxy

In this paper, the bond integrity of unmodified and rubber-modified epoxy used for bonding the carbon fibre sheets to the hosting steel surface was investigated. The rigidity of the bonding agent is one of the factors that have a significant role in the premature failure (debonding) of this application. In order to overcome this issue, a series of experiments were conducted on the steel plates using the epoxy resin modified by CTBN and ATBN reactive liquid polymers, in addition to the unmodified epoxy resin. The interface between the carbon fibre matrix and the hosting surface is subjected to a longitudinal shear force for which the corresponding displacement is recorded. The shear stress-strain relationship for the tested specimen is plotted. The result shows that, the bond behaviour of modified epoxy using CTBN and ATBN reactive liquid polymers was improved in terms of ductility and toughness.

One-pot facile synthesis of platinum nanoparticle decorated reduced graphene oxide composites and their application in electrochemical detection of rutin

We report on the synthesis of platinum nanoparticle-reduced graphene oxide (PtNP-rGO) composites and their application as a novel architecture in electrochemical detection of rutin. PtNPs anchored over rGO are synthesized through a facile one-pot synthesis method, where the reduction of GO and in situ generation of PtNPs occurred concurrently. The characterization results of transmission electron microscopy (TEM) demonstrate that PtNPs with small particle sizes are dispersed on the rGO matrix. Electrochemical measurements reveal that a PtNP-rGO modified glass carbon electrode (GCE) directly catalyzes rutin oxidation and displays an enhanced current response compared with a bare GCE. Under the optimal experimental conditions, the peak current was linear with rutin concentration in the range of 5 × 10^-8 to 1 × 10^-5 M with the detection limit of 1 × 10^-8 M (S/N = 3) by differential pulse voltammetry. The proposed method was successfully applied to determine rutin in tablet samples with satisfactory results. This journal is

High-performance composite from epoxy and glass fibers : morphology, mechanical, dynamic mechanical, and thermal analysis

Diglycidyl ether of bisphenol-A type epoxy resin cured with diamino diphenyl sulfone was used as the matrix for fiber-reinforced composites to get improved mechanical and thermal properties for the resulting composites. E-glass fiber was used for fiber reinforcement. The morphology, tensile, flexural, impact, dynamic mechanical, and thermal properties of the composites were analyzed. The tensile, flexural, and impact properties showed dramatic improvement with the addition of glass fibers. Dynamic mechanical analysis was performed to obtain the Tg of the cured matrix as well as the composites. The improved thermal stability of the composites was clear from the thermogravimetric analysis. Scanning electron micrographs were taken to understand the interfacial adhesion between the fiber and the matrix. The values of mechanical properties were compared with modified epoxy resin composite system. Predictive models were applied using various equations to compare the mechanical data obtained theoretically and experimentally.

Reactive block copolymer modified thermosets : highly ordered nanostructures and improved properties

A highly ordered poly(dimethyl siloxane)-poly(glycidyl methacrylate) (PDMS-PGMA) reactive diblock copolymer was synthesized and used to modify bisphenol A-type epoxy resin (ER). The PDMS-PGMA block copolymer consisted of epoxy-miscible PGMA blocks and an epoxy-immiscible PDMS block. The PGMA reactive block of the block copolymer formed covalent bonds with cured epoxy and was involved in the network formation, and the PDMS block phase separated to give different ordered and disordered nanostructures at different blend compositions. The solvent cast PDMS-PGMA diblock copolymer showed ordered hexagonal cylindrical morphology. A highly ordered morphology consisting of hexagonal cylinders inside the lamellar morphology was observed in the cured PDMS-PGMA block copolymer. In the cured ER/PDMS-PGMA blends, a variety of morphologies including lamellar, cubic and worm-like and spherical nanostructures were detected depending on the blend composition. Moreover, the addition of this reactive diblock copolymer significantly increases the hydrophobicity and the glass transition temperature. It also improves the tensile strength and tensile ductility of the nanostructured thermosets at low diblock copolymer contents.

Molecular dynamics study of a dual-cation ionomer electrolyte

The poly(N1222)xLi1-x[AMPS] ionomer system with dual cations has previously shown decoupled Li ion dynamics from polymer segmental motions, characterized by the glass transition temperature, which can result in a conductive electrolyte material whilst retaining an appropriate modulus (ie. stiffness) so that it can suppress dendrite formation, thereby improving safety when used in lithium metal batteries. To understand this ion dynamics behavior, molecular dynamics techniques have been used in this work to simulate structure and dynamics in these materials. These simulations confirm that the Li ion transport is decoupled from the polymer particularly at intermediate N1222+ concentrations. At 50 mol% N1222+ concentration the polymer backbone is more rigid than for higher N1222+ concentrations, but with increasing temperature Li ion transport is more significant than polymer or quaternary ammonium cation motions. Here we suggest an ion hopping mechanism for Li+, arising from structural rearrangement of ionic clusters that could explain its decoupled behavior. Higher temperatures favor an aggregated ionic structure as well as enhancing these hopping motions. The simulations discussed here provide an atomic-level understanding of ion dynamics that could contribute to designing an improved ionomer with fast ion transport and mechanical robustness.

Miscibility, crystallization κinetics and real-time small-Angle x-ray scattering investigation of the semicrystalline morphology in thermosetting polymer blends of epoxy resin and poly(ethylene oxide)

Thermosetting polymer blends of poly(ethylene oxide) (PEO) and bisphenol-A-type epoxy resin (ER) were prepared using 4,4′-methylenebis(3-chloro-2,6-diethylaniline) (MCDEA) as curing agent. The miscibility and crystallization behavior of MCDEA-cured ER/PEO blends were investigated by differential scanning calorimetry (DSC). The existence of a single composition-dependent glass transition temperature (Tg) indicates that PEO is completely miscible with MCDEA-cured ER in the melt and in the amorphous state over the entire composition range. Fourier-transform infrared (FTIR) investigations indicated hydrogen-bonding interaction between the hydroxyl groups of MCDEA-cured ER and the ether oxygens of PEO in the blends, which is an important driving force for the miscibility of the blends. The average strength of the hydrogen bond in the cured ER/PEO blends is higher than in the pure MCDEA-cured ER. Crystallization kinetics of PEO from the melt is strongly influenced by the blend composition and the crystallization temperature. At high conversion, the time dependence of the relative degree of crystallinity deviated from the Avrami equation. The addition of a non-crystallizable ER component into PEO causes a depression of both the overall crystallization rate and the melting temperature. The surface free energy of folding σe displays a minimum with variation of composition. The spherulitic morphology of PEO in the ER/PEO blends exhibits typical characteristics of miscible crystalline/amorphous blends, and the PEO spherulites in the blends are always completely volume-filling. Real-time small-angle X-ray scattering (SAXS) experiments reveal that the long period L increases drastically with increasing ER content at the same temperatures. The amorphous cured ER component segregates interlamellarly during the crystallization process of PEO because of the low chain mobility of the cured ER. A model describing the semicrystalline morphology of MCDEA-cured ER/PEO blends is proposed based on the SAXS results. The semicrystalline morphology is a stack of crystalline lamellae; the amorphous fraction of PEO, the branched ER chains and imperfect ER network are located between PEO lamellae.

Characterization of melded carbon fibre/epoxy laminates

‘Melding’ is a novel in situ method for joining thermosetting composite structures, without the need of adhesives. Laminate joining is achieved using uncrosslinked resin matrix of the pre-preg. This study used Hexply914C pre-preg material to characterize melded CFRP structures produced using the melding method. A designated area of a laminate was maintained at temperatures below 40 °C retaining uncured (B-staged) material, while the remainder of the laminate was cured at 175 °C. After a 2.5 h cure cycle, the cured region showed a high degree of cure (0.88) and glass transition temperature (176 °C). The uncured area of the same laminate was cured in a second stage, simulating an in situ melded joint. By controlling the temperature and duration of the intermediate dwell and affecting minimum viscosity values prior to final cure, low values of porosity (<0.5%) were achieved. The mechanical properties of the resulting joint were consistent throughout the melded laminate. Flexural strength (1600 MPa), flexural modulus (100–105 MPa) and short beam strength (105–115 MPa) values observed where equivalent or greater than those found in the recommended autoclave cured control specimens. After the entire laminate was post cured, glass transition temperatures of 230 °C (peak tan δ) were observed in all areas of the laminate.

Reduction of fuel consumption in an industrial glass melting furnace

Reduction of fuel consumption in glass melting furnaces can cut the cost of production, and tackle the global warming. This paper presents three independent solutions to reduce the fuel consumption in industrial glass melting furnaces. The solutions include air preheating, raw material preheating, and improving the insulation of combustion space refractory. Energy balance equations are derived and used to identify the effects of each solution. The results indicate that the three solutions reduce the fuel consumption by 9.5%, 17%, and 34%, respectively.

Modified life cycle inventory of aluminium die casting

Aluminium die casting is a process used to transform molten aluminium material into automotive gearbox housings, wheels and electronic components, among many other uses. It is used because it is a very efficient method of achieving near net shape with the required mechanical properties. Life Cycle Assessment (LCA) is a technique used to determine the environmental impacts of a product or process. The Life Cycle Inventory (LCI) is the initial phase of an LCA and describes which emissions will occur and which raw materials are used during the life of a product or during a process. This study has improved the LCI technique by adding in manufacturing and other costs to the ISO standardised methods. Although this is not new, the novel application and allocation methods have been developed independently. The improved technique has then been applied to Aluminium High Pressure Die Casting. In applying the improved LCI to this process, the cost in monetary terms and environmental emissions have been determined for a particular component manufactured by this process. A model has been developed in association with an industry partner so this technique can be repeatedly applied and used in the prediction of costs and emissions. This has been tested with two different products. Following this, specialised LCA software modelling of the aluminium high pressure die casting process was conducted. The variations in the process have shown that each particular component will have different costs and emissions and it is not possible to generalise the process by modelling only one component. This study has concentrated on one process within die casting but the techniques developed can be used across any variations in the die casting process.

Structural and material properties of a rapidly cured thermoplastic-toughened epoxy system

Thermoplastic-toughened epoxy resins are widely used as matrices in modern composite prepreg systems. Rapid curing of thermoplastic-toughened epoxy matrix composites results in different mechanical properties. To investigate the structure–property relationship, we investigated a poly(ether sulfone)-modified triglycidylaminophenol/ 4,4'-diamino diphenyl sulfone system that was cured at different heating rates. An intermediate dwell was also applied during the rapid heating of the thermoplasticmodified epoxy system. We found that a higher heating rate led to a larger domain size of the phase-separated macrostructure and also facilitated more complete phase separation. The intermediate dwell helped phase separation to proceed even further, leading to an even larger domain size of the macrostructure. A carbon-fiber-reinforced polymer matrix composite prepreg based on the poly(ether sulfone)-modified multifunctional epoxy system was cured with the same schedule. The rapidly heated composite laminates exhibited higher mode I delamination fracture toughness than the slowly heated material.

SEMI-SYNTHETIC MATERIAL

The invention relates to a modified ultra-fine natural fibre powder for use in a melt forming process for the preparation of a semi-synthetic material, the powder including particles of a natural fibre modified to improve the heat stability of the natural fibre powder particles during said melt forming process. The invention also relates to a semi-synthetic material including a modified ultra-fine natural fibre powder and a synthetic polymer component.

Semi-synthetic material

The invention relates to a modified ultra-fine natural fibre powder for use in a melt forming process for the preparation of a semi-synthetic material, the powder including particles of a natural fibre modified to improve the heat stability of the natural fibre powder particles during said melt forming process. The invention also relates to a semi-synthetic material including a modified ultra-fine natural fibre powder and a synthetic polymer component.