Aging studies on conducting polypyrrole

Change of tensile properties, electrical conductivity and microwave shielding of electrochemically synthesized polypyrrole films with time are presented. Highly doped films had good electrical stability, retaining high microwave reflectivity throughout the aging period. Lightly doped films were less stable and partially reflective and absorptive of microwaves. FT-IR spectral observations revealed a progressive increase in intensity of an unsaturated conjugated carbonyl peak, which was not observed in the highly doped films, suggesting that the concentration of the dopant had an influence on the mechanism of degradation of conductivity.

Effect of synthesis parameters on the electrical conductivity of polypyrrole-coated poly(ethylene terephthalate) fabrics

The effects of pyrrole, anthraquinone-2-sulphonic acid (AQSA) and iron(III) chloride (FeCl3) concentrations, reaction time and temperature on the electrical conductivity of polypyrrole (PPy) - coated poly(ethylene terephthalate) (PET) fabrics were investigated. With an increase in both the AQSA and FeCl3 concentrations, resistivity decreased to a point beyond which higher concentrations led to increased surface resistivity. Erosion of the polymer coating, in dynamic synthesis from continual abrasion, manifested as an exponential increase in the resistance of the coated textile substrate. This was not encountered in static synthesis conditions. Temperature affected the degree of surface and bulk polymerisation. The effect of polymerisation temperature on conductivity was negligible. Conductive polymer coating on textiles through chemical polymerisation enabled a smooth coherent film to encase individual fibres, which did not affect the tactile properties of the host substrate. The optimum FeCl3/pyrrole and AQSA FeCl3/pyrrole molar ratios were found to be 2.22 and 0.40 respectively.

Generating heat from conducting polypyrrole-coated PET fabrics

Heating effects in polypyrrole-coated polyethyleneterephthalate (PET)-Lycra® fabrics were studied. Chemical synthesis was employed to coat the PET fabrics by polypyrrole using ferric chloride as oxidant and antraquinone- 2-sulfonic acid (AQSA) and naphthalene sulfonic acid (NSA) as dopants. The coated fabrics exhibited reasonable electrical stability, possessed high electrical conductivity, and were effective in heat generation. Surface resistance of polypyrrole-coated fabrics ranged from approximately 150 to 500 /square. Different connections between conductive fabrics and the power source were examined. When subjected to a constant voltage of 24 V, the current transmitted through the fabric decreased about 10% in 72 h. An increase in resistance of conductive fabrics subjected to constant voltage was observed

Polypyrrole nanoparticles and dye absorption properties

Polypyrrole (PPy) nanoparticles were prepared by using microemulsion polymerization processes at 3 °C. Particle characterization was performed by using FTIR, elementary analysis, UV–vis spectra and scanning electron microscope (SEM). The size of the nanoparticles varied from about 50 to 100 to 100 to 200 nm with the change in concentration of surfactant from 0.8 to 0.44 M. Polypyrrole nanoparticles were dedoped by a 10% NaOH solution, followed by a redoping process using a nuclear fast red kernechtrot dye, which has a sulfonate group. Dedoping changed the optical absorption properties of the nanoparticles.

Electromagnetic shielding properties of polypyrrole/polyester composites in the 1–18 GHz frequency range

The dielectric characteristics of conducting polymer-coated textiles in the frequency range 1–18 GHz were investigated using a non-contact, non-destructive free space technique. Polypyrrole coatings were applied by solution polymerization on fabric substrates using a range of concentrations of para-toluene-2-sulfonic acid (pTSA) as dopant and ferric chloride as oxidant. The conducting polymer coatings exhibited dispersive permittivity behaviour with a decrease in real and imaginary components of complex permittivity as frequency increased in the range tested. Both the permittivity and the loss factor were affected by the polymerization time of the conductive coating. It was found that the total shielding efficiency of these conductive fabrics is significant at short polymerization times and increases to values exceeding 80% with longer polymerization times. The reflection contribution to electromagnetic shielding also increases with polymerization time.

The effects of dye dopants on the conductivity and optical absorption properties of polypyrrole

Ten anionic compounds, including four acidic dyes, were used to dope polypyrrole powder. The effects of the dopants on density, optical absorption and conductivity of the polypyrroles were studied. The presence of the dopant in the conducting polymer matrix was verified by ATR-FTIR spectroscopy. Density function theory (DFT) simulation was used to understand the effect of the dopants on the solid structure, optical absorption and energy band structures. Anthraquinone-2-sulfonic acid-doped polypyrrole yielded the highest conductivity. The dye-doped polypyrrole showed an enhancement in its UV–vis optical absorption.

Improvement of adhesion of conductive polypyrrole coating on wool and polyester fabrics using atmospheric plasma treatment

In this paper wool and polyester fabrics were pretreated with atmospheric plasma glow discharge (APGD) to improve the ability of the substrate to bond with anthraquinone-2-sulfonic acid doped conducting polypyrrole coating. A range of APGD gas mixtures and treatment times were investigated. APGD treated fabrics were tested for surface contact angle, wettability and surface energy change. Effect of the plasma treatment on the binding strength was analyzed by studying abrasion resistance, surface resistivity and reflectance. Investigations showed that treated fabrics exhibited better hydrophilicity and increased surface energy. Surface treatment by an APGD gas mixture of 95% helium/5% nitrogen yielded the best results with respect to coating uniformity, abrasion resistance and conductivity.

Electromagnetic interference shielding and radiation absorption in thin polypyrrole films

Results of permittivity measurements, electromagnetic interference shielding effectiveness, and heat generation due to microwave absorption in conducting polymer coated textiles are reported and discussed. The intrinsically conducting polymer, polypyrrole, doped with anthraquinone-2-sulfonic acid (AQSA) or para-toluene-2-sulfonic acid (pTSA) was applied on textile substrates and the resulting materials were investigated in the frequency range 1–18 GHz. The 0.54 mm thick conducting textile/polypyrrole composites absorbed up to 49.5% of the incident 30–35 W microwave radiation. A thermography station was used to monitor the temperature of these composites during the irradiation process, where absorption was confirmed via visible heat losses. Samples with lower conductivity showed larger temperature increases caused by microwave absorption compared to samples with higher conductivity. A sample with an average sheet resistivity of 150 Ω/sq. showed a maximum temperature increase of 5.27 °C, whilst a sample with a lower resistivity (105 Ω/sq.) rose by 3.85 °C.

Polypyrrole-coated electrospun nanofibre membranes for recovery of Au(III) from aqueous solution

In this paper, for the first time, polypyrrole-coated electrospun nanofibre mats have been used as separation membranes to electrolessly recover Au from aqueous [Au(III)Cl₄]− solutions, based on a continuous-flow membrane separation process. With a [Au(III)Cl₄]− solution passing through the nanofibre membrane, the Au(III) ions were converted into elemental Au. The gold recovered was deposited on the nanofibre membranes in the form of Au particles, as confirmed by EDX and XPS measurements. It has been found that the polypyrrole-coated electrospun nanofibres are good candidate membrane material for the recovery of Au, and the recovery efficiency is affected by the membrane thickness, the permeate flux rate and the initial [Au(III)Cl₄]− concentration.

Effect of weight reduction pre-treatment on the electrical and thermal properties of polypyrrole coated woven polyester fabrics

Weight reduction increased the amount of deposited polypyrrole (PPy) on the polyester (PET) fiber surface, leading to a considerable decrease in electrical resistance and improved heat generation capacity for the PPy coated PET fabrics. Application of dc voltages to an insulated roll of PPy-coated fabric increased the temperature to about 90 °C. This showed the suitability of these fabrics for heating applications. The optimum PPy deposition of about 2.8% was obtained in samples weight reduced by aqueous sodium hydroxide treatment. AFM images revealed a smooth surface morphology of the untreated fiber whereas the treated fiber had a high surface roughness.

Effects of laundering on conductivity of polypyrrole-coated textiles

This study examines the resistance change in conductive polypyrrole-coated PET fabrics under the AS 2001.4.15 – 1994 laundering test conditions. The effects of individual detergent components of a standard detergent, including auxiliary chemicals, at four different temperatures were studied. When the coated fabric was washed under the AS 2001.4.15-1994 conditions, the ECE reference detergent and pure soap flakes (sodium sterate) both decreased the conductivity of the coating at a rate exponentially proportional to the laundering temperature. Detergent types had an influence over the rate of degradation; pH conditions had a large influence on the rate of polymer deterioration with the acidic nonionic detergent giving rise to significantly improved laundering conditions. The auxiliary chemicals, sodium carbonate and sodium perborate were seen to cause large degradation of polymers during laundering. Ethylene diamine tetra acetic acid was seen to have only a slight influence on the reduction of conductivity of polymers.