Thinning of a vertical free draining aqueous film incorporating colloidal particles

The drainage under gravity of a vertical foam film formed on a wire frame has been investigated. Dual-wavelength optical interferometry was used so that unambiguous fringe order assignments could be made, enabling absolute film thicknesses to be calculated with confidence. Films were stabilized by nonionic polypropylene glycol surfactant. Halfmicrometer silica particles with varying degrees of hydrophobicity were added to the film-forming liquid to investigate their effect on film drainage rate and stability. Hydrophilic particles had little or no effect, while hydrophobic particles slowed the drainage of the film and caused a minor increase in film lifetime, from ∼10 to ∼30 s. In both the hydrophilic and hydrophobic cases the films ruptured when they reached a thickness of ∼2 particle diameters. Particles of intermediate hydrophobicity had the most significant effect, increasing film lifetime by an order of magnitude over that for hydrophilic particles. The intermediate particles allowed films to thin down to a thickness less than the particle diameter, indicating that particles bridge across the entire film. This did not occur with more hydrophobic particles even though they were embedded in each of the two film surfaces. These results correlate well with previous literature on particle-laden foams. The film thickness and drainage measurements allow drainage mechanisms for the different particles to be identified, thus providing a mechanistic explanation for the observation by several previous authors that foams formed in the presence of particles, for example during mineral processing, have the greatest stability when the particles are of intermediate hydrophobicity.

Improvement in mechanical properties of aluminum polypropylene composite fiber

Aluminum particles (Al) were added to polypropylene (PP) in the presence of poly ethylene glycol (PEG) and polypropylene-graft-maleic anhydride to produce composites. The composites were then melt-spun into a mono filament and tested for tensile properties, diameter evenness and morphology. Melt rheological properties of Al/PP composites were studied in linear viscoelastic response regions. It was observed that level of dispersion of aluminum particles within a polypropylene composite fiber could be improved by incorporating polyethylene glycol. The improvement of dispersion led to an improvement in the fibers mechanical properties through a reduction of the coefficient of variation of fiber diameter.

Retention of the original LLC structure in a cross-linked poly(ethylene glycol) diacrylate hydrogel with reinforcement from a silica network

Cross-linked poly(ethylene glycol) diacrylate (PEGDA) hydrogels with uniformly controlled nanoporous structures templated from hexagonal lyotropic liquid crystals (LLC) represent separation membrane materials with potentially high permeability and selectivity due to their high pore density and narrow pore size distribution. However, retaining LLC templated nanostructures is a challenge as the polymer gels are not strong enough to sustain the surface tension during the drying process. In the current study, cross-linked PEGDA gels were reinforced with a silica network synthesized via an in situ sol-gel method, which assists in the retention of the hexagonal LLC structure. The silica precursor does not obstruct the formation of hexagonal phases. After surfactant removal and drying, these hexagonal structures in samples with a certain amount of tetraethoxysilane (TEOS) loading are well retained while the nanostructures are collapsed in samples without silica reinforcement, leading to the hypothesis that the reinforcement provided by the silica network stabilizes the LLC structure. The study examines the conditions necessary for a sufficient and well dispersed silica network in PEGDA gels that contributes to the retention of original LLC structures, which potentially enables broad applications of these gels as biomedical and membrane materials.

Enhanced homogeneity and interfacial compatibility in melt-extruded cellulose nano-fibers reinforced polyethylene via surface adsorption of poly(ethylene glycol)-block-poly(ethylene) amphiphiles

In this paper, we demonstrate that an amphiphilic block copolymer such as polyethylene glycol-b-polyethylene can be used as both dispersing and interfacial compatibilizing agent for the melt compounding of LLDPE with cellulose nano-fibers. A simple and effective spray drying methodology was first used for the first time for the preparation of a powdered cellulose nano-fibers extrusion feedstock. Surface adsorption of the amphiphilic PEG-b-PE was carried out directly in solution during this process. These various dry cellulosic feedstock were subsequently combined with LLDPE via extrusion to produce a range of nano-composites. The collective outcomes of this research are several folds. Firstly we show that presence of surface adsorbed PEG-b-PE effectively hindered the aggregation of the cellulose nano-fibers during the extrusion, affording clear homogenous materials with minimum aggregation even at the highest loading of cellulose nano-fibers (∼23 vol.%). Secondly, the tailored LLDPE/cellulose interface arising from intra- and inter-molecular hydrogen and Van der Waals bonds yielded significant levels of mechanical improvements in terms of storage and tensile modulus. We believe this study provides a simple technological template to produce high quality and performant polyolefins cellulose-based nano-composites.

Bleaching and dyeing of superfine wool powder/polypropylene blend film

Fibers based regenerated protein draw much attention for recycling discarded protein resources and can produce biodegradable and environmental friendly polymers. In this study, superfine wool powder is blended with polypropylene (PP) to produce wool powder/PP blend film through extrusion and hot-pressing. Hydrogen peroxide is used to bleach the black colored surface of the blend films. The effects of peroxide concentration, bleaching time and powder content on the final whiteness and mechanical properties of the blend films are investigated.

The bleached films are dyed with acid red dyes and the dyed color is evaluated using a Computer Color Matching System. Color characters of dyed films, such as L*, a*, b*, ΔE*ab, C*ab and K/S values are measured and analyzed. The study not only reuses discarded wool resources into organic powder, widens the application of superfine wool powder on polymers, but also improves the dyeing properties of PP through the addition of protein content.

Preparation of cross-linked nanoporous poly(ethylene glycol) diacrylate membrane in hexagonal lyotropic liquid crystal phases

Cross-linked poly(ethylene glycol) diacrylate (PEGDA) membranes were prepared by polymerization in periodic nanostructured lyotropic liquid crystals (LLC) hexagonal phases under UV light. A series of membranes were prepared under different purification treatment conditions. Polarized light microscope was employed to determine the LLC phase texture of LLC system before and after polymerization. It is found that the LLC hexagonal structure retained to some degree after polymerization. The interior structures of final membranes were investigated with scanning electron microscope (SEM). The results suggested that purification process affect the structure retention.

Ionic conductivity in poly(diethylene glycol-carbonate)/sodium triflate complexes

New polymer electrolytes were synthesized and characterized based on a new polymer host. The motivation was to produce a host polymer with a high dielectric constant which should reduce ion clustering with an attendant increased conductivity. The new polymer host, poly(diethylene glycol carbonate) and its sodium triflate complexes were characterized by thermal analysis and AC impedance measurements. The polycarbonate backbone appears less flexible than the polyether hosts as evidenced by the higher glass transition temperatures. The conductivity for the sodium triflate complexes was measured as ~ 10⁻⁵ S cm⁻¹ at 55 °C and the dielectric constant of the host polymer was found to be 3.6 at 3 GHz. The low conductivity is attributed to rigidity of the polycarbonate.

Exploring molecular changes at the surface of polypropylene after accelerated thermomolecular adhesion treatments

A central composite rotatable design (CCRD) method was used to investigate the performance of the accelerated thermomolecular adhesion process (ATmaP), at different operating conditions. ATmaP is a modified flame-treatment process that features the injection of a coupling agent into the flame to impart a tailored molecular surface chemistry on the work piece. In this study, the surface properties of treated polypropylene were evaluated using X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). All samples showed a significant increase in the relative concentration of oxygen (up to 12.2%) and nitrogen (up to 2.4%) at the surface in comparison with the untreated sample (0.7% oxygen and no detectable nitrogen) as measured by XPS. ToF-SIMS and principal components analysis (PCA) showed that ATmaP induced multiple reactions at the polypropylene surface such as chain scission, oxidation, nitration, condensation, and molecular loss, as indicated by changes in the relative intensities of the hydrocarbon (C₃H₇⁺ , C₃H₅⁺ , C₄H₇⁺, and C₅H₉⁺), nitrogen and oxygen-containing secondary ions (C₂H₃O⁺, C₃H₈N⁺, C₂H₅NO⁺, C₃H₆NO⁺, and C₃H₇NO⁺). The increase in relative intensity of the nitrogen oxide ions (C₂H₅NO⁺ and C₃H₇NO⁺) correlates with the process of incorporating oxides of nitrogen into the surface as a result of the injection of the ATmaP coupling agent.

Forces between mica surfaces in ethylene glycol

Measurements are presented of the force as a function of separation between two molecularly smooth mica surfaces immersed in ethylene glycol, and in solutions of lithium chloride and sulfuric acid in ethylene glycol. At surface separations greater than 3 nm the measured force is in very good agreement with double-layer theory, but at smaller separations there is an oscillatory solvation force which is superimposed on the double-layer repulsion. In contrast to the case in water, the adsorption of hydrogen ions at the mica surface does not markedly affect the short-range forces.

Concomitant reactivity of the m-Terphenylindium dihydroxide [2,6-Mes2C6H3In(OH)2]4 toward carbon dioxide and ethylene glycol

The stepwise reaction of [2,6-Mes₂C₆H₃In(OH)₂]₄ with carbon dioxide and ethylene glycol proceeded with the formation of (2,6-Mes₂C₆H₃In)₄(CO₃)₂(OH)₄(H₂O)₂ (1) and (2,6-Mes₂C₆H₃In)₄(OCH₂CH₂O)₂(OH)₄ (2), respectively, and eventually produced (2,6-Mes₂C₆H₃In)₄(CO₃)₂(OCH₂CH₂OH)₂(OH)₂ (3). Attempts to liberate ethylene carbonate upon heating of 3 were unsuccessful.