Photocatalytic decolorization of lanasol blue CE dye solution using a flat-plate reactor

This paper reports the effectiveness of the photocatalysis TiO₂ in degrading Lanasol Blue CE. A flat-plate reactor (FPR) with a reactor area of 0.37 m² and ultraviolet (UV) light source of six 36 W blacklight lamps was used in the study. Operating variables including dosage of the photocatalyst, flow rates through the FPR, UV intensity, and tilted angle of the reactor were investigated to degrade Lanasol Blue CE. Results showed that the photocatalytic process can efficiently remove the color in textile dyeing effluent. The degradation process was approximated using first-order kinetics. The photocatalytic apparent reaction rate increased with the increasing UV intensity received by the photocatalyst TiO₂ in slurry. The liquid flow rate and tilted angle influenced the film thickness. The apparent reaction rate constant was mainly determined by the liquid film thickness, UV intensity, and the dosage of the photocatalyst. The findings of this research can be utilized as preliminary input for potential solar photocatalytic applications on color removal from dye solutions.

Photocatalytic degradation of dyes in wastewater using TiO2/UV in a flat-plate reactor

The photocatalyst TiO₂ with UV irradiation was used to degrade dyes in textile effluent in a flat-plate photoreactor. A test system was built with the reactor area of 1 x 0.3m2, UV light of six 36W-blacklight. TiO₂ powder P25 with BET surface area 50±15m2/g, average primary particle size 21 nm, purity> 99.5% and content of 83.9% anatase and 16.1 % rutile was used as the photocatalyst. A number of dyes commonly present in dyeing wastewater were tested in this study. The different operating parameters, such as dosage of photocatalyst, the structure of the reactor, flow rates through the flat-plate reactor, UV radiation intensity and tilted angle of the reactor, were investigated. The results showed that the photocatalytic process could efficiently remove most of the colour contained in the dyeing wastewater. It was experimentally observed that first-order kinetics was adequate for characterising the process. The flow rate and the tilted angle had some influence on the film thickness of the fluid in the reactor and the empirical correlation between the film thickness of the fluid and these two parameters was developed. The photoreaction rate was mainly determined by the film thickness of the fluid on the reactor surface and the dosage of the photocatalyst. Optimum operating parameters of the system were found to be at the film thickness of about 1.4mm and a TiO₂ dosage of 1 gIL. The higher the UV intensity, the faster the reaction rate was. The results of these experiments showed that this method has the great potential for colour removal from wastewater at commercial scale.

To overcome the common difficulty of separating the used TiO₂ suspension after treatment precipitation followed with filtration was used in this study to determine the separation efficiencies. On the other hand, TiO₂ in a small pillar shape was also studied for photocatalytic degradation of textile dye effluent. The pillar pellet was made in Oegussa Company, Germany ranging from 2.5 to 5.3mm long and with a diameter of 3.7mm. It was almost pure TiO₂ (83.2% anatase and 16.8% rutile), with a S-content of <20 ppm and a CI content of the order of 0.1 wt. %. No further elements are present in contents above 0.05 wt.%. The TiO₂ pillars were placed on the flat-plate reactor that was divided by the rectangular slots and irradiated under UV light when the treated solution went through the reactor. Four dyes and their mixtures were tested. The results showed that the photocatalytic process under this configuration efficiently remove the colour from textile dyeing effluent, and pillar shape TiO₂ photocatalyst was not dissolved in water and very easy to be separated from solution, enabling it to be reused many times. The first-order kinetics was adequate for characterising the photocatalytic degradation process and the photocatalytic performance was comparable to TiO₂ powder. It is believed that the TiO₂ pellet would be a preferable form of photocatalyst in applications for textile effluent treatment process, and other wastewater treatment processes.

Solar photocatalytic oxidation (PCO) process with a flat-plate reactor

An experimental rig with a flat-plate solar reactor was built to study the effectiveness of degradation using the reactive methylene blue as sensitive objective. The factors that affect the degradation performance, such as dosages of photocatalyst (Ti0₂), initial concentration of reactive methylene blue, flow rate through the flat-plate reactor, solar UV radiation intensity and decolourising efficiency of the solution, have been investigated. The results showed that the solar PCO process with a Flat-plate Reactor could degrade the methylene blue and decolour in methylene blue solution efficiently.

A comparative study of microstructures and mechanical properties obtained by bar and plate rolling

Microstructures and mechanical properties of a low carbon steel were studied after plate rolling and bar rolling. Plate rolling is characterized as a monotonic compressive loading, while bar rolling is characterized as a cross-compressive loading. A four-pass plate rolling and bar rolling experiment was designed so that the material experiences the same amount of strain at each pass during rolling. The rolling experiment was performed at moderately high temperatures (450, 550 and 650 °C). The microstructures and mechanical properties of the low carbon steel acquired from the two types of rolling experiments were compared. The results revealed that differences of loading path attributed by monotonic loading (plate rolling) and cross loading (bar rolling) significantly influenced the microstructures and mechanical properties such as yield stress, ultimate tensile stress, strain hardening exponent and elongation of the low carbon steel.

Construction of extrusion limit diagram for AZ31 magnesium alloy by FE simulation

The maximum speed at which magnesium can be extruded is considerably slower than that of many common aluminium extrusion alloys. This affects both the economies of production and the final mechanical behaviour. The present work quantifies the limiting extrusion speeds and ratios of magnesium alloy AZ31 as a function of billet temperature. This is done by combining hot compression test results, FE simulations and extrusion trials. Hot working stress–strain curves displayed a distinct dynamic recrystallisation peak. These data were used as a “look-up” table for the FE simulations in which the cracking limit was assumed to occur when the surface temperature reaches the incipient melting point. The maximum extrusion ratio predicted using FE analysis dropped from 90 to 40 when the extrusion ram speed was raised from 5 to 50 mm/s. The predicted limits agree well with the occurrence of cracking in both a laboratory and a commercial extrusion trial.

When does physiology limit the foraging behaviour of freely diving mammals?

Diving animals offer a unique opportunity to study the importance of physiological constraint and the limitation it can impose on animal's behaviour in nature. This paper examines the interaction between physiology and behaviour and its impact on the diving capability of five eared seal species (Family Otariidae; three sea lions and two fur seals). An important physiological component of diving marine mammals is the aerobic dive limit (ADL). The ADL of these five seal species was estimated from measurements of their total body oxygen stores, coupled with estimates of their metabolic rate while diving. The tendency of each species to exceed its calculated ADL was compared relative to its diving behaviour. Overall, our analyses reveal that seals which forage benthically (i.e. on the sea floor) have a greater tendency to approach or exceed their ADL compared to seals that forage epipelagically (i.e. near the sea surface). Furthermore, the marked differences in foraging behaviour and physiology appear to be coupled with a species demography. For example, benthic foraging species have smaller populations and lower growth rates compared to seal species that forage epipelagically. These patterns are relevant to the conservation and management of diving vertebrates.

Nutrient intake and plate waste from an Australian residential care facility

Objective: To determine the plate waste, energy and selected-nutrient intake, from elderly residents living in a high-level care (HLC) and low-level care (LLC) facility.

Design: Three, single, whole day assessments of plate waste, energy, and selected nutrients, using a visual rating plate waste scale.

Setting: Long-term residential care establishment.

Subjects: One hundred and sixty-nine (93 HLC and 76 LLC) individual daily intakes.

Main findings: The mean energy wasted throughout the whole day was 17%. The energy wasted from main meals (16%) was significantly less than the energy wasted at mid-meals (22%, P=0.049). The lowest mean energy wastage occurred at breakfast (8%) compared to lunch (22%) and dinner (25%, P<0.001). The mean (s.d.) daily energy served and consumed was 8.1 (2.0) and 6.6 (2.2) MJ, respectively. There was no difference in energy served or consumed between HLC and LLC residents. On the observation day, 60% of residents consumed less than their estimated energy requirement. The mean calcium intake was 796 (346) mg, and the median (inter-quartile range) vitamin D intake was 1.78 (2.05) μg.

Conclusion: On 1 day, more than half the residents surveyed were at risk of consuming an inadequate energy intake, which over-time, may result in body weight loss. Although wastage was not excessive and energy served was adequate, the amount of food eaten was insufficient to meet energy and calcium requirements for a significant number of residents and it is not possible to consume sufficient vitamin D through food sources.

Laminated plate elements based on higher-order shear deformation theories

Efficient and accurate finite elements are crucial for finite element analysis to provide adequate prediction of the structural behavior. A large amount of laminated plate elements have been developed for finite element analysis of laminated composite plates based on the various lamination theories. A recent and complete review of the laminated finite elements based on the higher-order shear deformation theories, including the global higher-order theories, zig-zag theories and the global-local higher-order theories is presented in this paper. Finally some points on the development of the laminated plate elements are summarized.

No limits : exploring the psychology of unsolicited credit card limit increase offers

The issue of credit card debt has become an increasing concern in recent years. In Australia, for example, there is currently $42.5 billion worth of outstanding debt on credit cards, with $30 billion (over 70 per cent) bearing interest. Further, in 2001, Visa reported that 32 per cent of consumers had not paid their card off in the previous 12 months, which suggests that interest-bearing debt in Australia is held by approximately only 113 of credit card borrowers. An important element of credit card marketing is the use of psychological manipulations to encourage consumers to take-up credit. In this article, we examine the use of language and imagery in unsolicited credit card limit increase offers, and how these might influence consumers' decisions to increase their credit card limit. The analysis found that the use of terms that focused on the benefits of credit card use, such as "choice", "freedom", and "peace of mind" were used consistently to convince consumers to increase their credit card limit, whereas the use the of terms that could be considered more pragmatic and with direct reference to the nature of the product, such as "debt", "repayment" and "loan", were rarely used. Similarly, the use of colour, text changes, and images, were used which may have an influence over a consumer's ability to rationally consider whether the increase is appropriate for them. The paper concludes by recommending that government and representative bodies need to take into account the psychological manipulations used by credit card providers when developing consumer policy and codes of ethics.

Congratulations, you're pre-approved! : an analysis of credit limit upselling letters

Consumer Action commissioned Dr Paul Harrison, Deakin Business School, Deakin University and Marta Massi, School of Marketing and Communication, Lumsa University (Rome), to study the psychological aspects of one form of credit marketing – unsolicited credit card limit-increase offers (UCCLIOs). The researchers studied 21 UCCLIO letters – 17 provided by consumers and four provided by banks – and applied theories developed from previous research in the fields of marketing, consumer behavior, behavioural economics and cognitive psychology, to describe likely ways in which UCCLIO’s influenced consumer behavior and decision making. The researchers make some recommendations from a behavioural perspective based on their findings, and Consumer Action proposes how these findings might be applied to consumer policy.

Process for the production of ultrafine plate-like alumina particles

A process for producing plate-like alumina particles with a high aspect ratio is described. Nano-sized particles of an aluminium precursor compound, optionally formed by milling, are mixed with a sufficient volume fraction of a diluent and heat treated to form substantially discrete plate-like alpha alumina particles dispersed in the diluent. A mineraliser may be added to lower the effective melting point of the system. Substantially discrete plate-like particles may be formed without agitation when the heat treatment is conducted below the melting point of the diluent.