Light emission and excitonic effect of boron nitride nanotubes observed by photoluminescent spectra

Photoluminescent (PL) and optical absorption spectra of high-yield multi-wall BN nanotubes (BNNTs) were systematically investigated at room temperature in comparison with commercial hexagonal BN (h-BN) powder. The direct band gap of the BNNTs was determined to be 5.75 eV, just slightly narrower than that of h-BN powder (5.82 eV). Two Frenkel excitons with the binding energy of 1.27 and 1.35 eV were also determined. However, they were not a distinctive characteristic of the BNNTs as reported previously. Observed broad UV–visible–NIR light emission demonstrates the potential of the BNNTs as a nano light source.

Donor-п-acceptor conjugated copolymers for photovoltaic applications : tuning the open-circuit voltage by adjusting the donor/acceptor ratio

A class of new conjugated copolymers containing a donor (thiophene)−acceptor (2-pyran-4-ylidene-malononitrile) was synthesized via Stille coupling polymerization. The resulting copolymers were characterized by 1H NMR, elemental analysis, GPC, TGA, and DSC. UV−vis spectra indicated that the increase in the content of the thiophene units increased the interaction between the polymer main chains to cause a red-shift in the optical absorbance. Cyclic voltammetry was used to estimate the energy levels of the lowest unoccupied molecular orbital (LUMO) and the highest occupied molecular orbital (HOMO) and the band gap (Eg) of the copolymers. The basic electronic structures of the copolymers were also studied by DFT calculations with the GGA/B3LYP function. Both the experimental and the calculated results indicated an increase in the HOMO energy level with increasing the content of thiophene units, whereas the corresponding change in the LUMO energy level was much smaller. Polymer photovoltaic cells of a bulk heterojunction were fabricated with the structure of ITO/PEDOT/PSS (30 nm)/copolymer−PCBM blend (70 nm)/Ca (8 nm)/Al (140 nm). It was found that the open-circuit voltage (Voc) increased (up to 0.93 V) with a decrease in the content of thiophene units. Although the observed power convention efficiency is still relatively low (up to 0.9%), the corresponding low fill factor (0.29) indicates considerable room for further improvement in the device performance. These results provided a novel concept for developing high Voc photovoltaic cells based on donor-π-acceptor conjugated copolymers by adjusting the donor/acceptor ratio.

C-BN single-walled nanotubes from hybrid connection of BN/C nanoribbons : prediction by ab initio density functional calculations

We demonstrated for the first time by ab initio density functional calculation and molecular dynamics simulation that C0.5(BN)0.5 armchair single-walled nanotubes (NT) are gapless semiconductors and can be spontaneously formed via the hybrid connection of graphene/BN Nanoribbons (GNR/BNNR) at room temperature. The direct synthesis of armchair C0.5(BN)0.5 via the hybrid connection of GNR/BNNR is predicted to be both thermodynamically and dynamically stable. Such novel armchair C0.5(BN)0.5 NTs possess enhanced conductance as that observed in GNRs. Additionally, the zigzag C0.5(BN)0.5 SWNTs are narrow band gap semiconductors, which may have potential application for light emission. In light of recent experimental progress and the enhanced degree of control in the synthesis of GNRs and BNNR, our results highlight an interesting avenue for synthesizing a novel specific type of C0.5(BN)0.5 nanotube (gapless or narrow direct gap semiconductor), with potentially important applications in BNC-based nanodevices.

Incorporation of fused tetrathiafulvalenes (TTFs) into polythiophene architectures : varying the electroactive dominance of the TTF species in hybrid systems

A novel polythienylenevinylene (PTV) and two new polythiophenes (PTs), featuring fused tetrathiafulvalene (TTF) units, have been prepared and characterized by ultraviolet−visible (UV−vis) and electron paramagnetic resonance (EPR) spectroelectrochemistry. All polymers undergo two sequential, reversible oxidation processes in solution. Structures in which the TTF species is directly linked to the polymer backbone (2 and 4) display redox behavior which is dictated by the fulvalene system. Once the TTF is spatially removed from the polymer chain by a nonconjugated link (polymer 3), the electroactivity of both TTF and polythiophene moieties can be detected. Computational studies confirm the delocalization of charge over both electroactive centers (TTF and PT) and the existence of a triplet dication intermediate. PTV 4 has a low band gap (1.44 eV), is soluble in common organic solvents, and is stable under ambient conditions. Organic solar cells of polymer 4:[6,6]-phenyl-C₆₁ butyric acid methyl ester (PCBM) have been fabricated. Under illumination, a photovoltaic effect is observed with a power conversion efficiency of 0.13% under AM1.5 solar simulated light. The onset of photocurrent at 850 nm is consistent with the onset of the π−π absorption band of the polymer. Remarkably, UV−vis spectroelectrochemistry of polymer 4 reveals that the conjugated polymer chain remains unchanged during the oxidation of the polymer.

Large-scale synthesis and growth mechanism of single-crystal Se nanobelts

Single-crystal trigonal (t) Se nanobelts have been synthesized on a large scale by reducing SeO2 with glucose at 160 °C. Electron microscopy images show that the nanobelts are 80 nm in diameter, 25 nm in thickness, and up to several hundreds of micrometers in length. HRTEM images prove that the nanobelts are single crystals and preferentially grow along the [001] direction. The time-dependent TEM images revealed that the formation and growth of t-Se nanobelts were governed by a solid−solution−solid growth mechanism. The redox reaction directly produced amorphous (α) Se nanoparticles under hydrothermal conditions. t-Se nanobelts were formed by dissolution and recrystallization of the initial α-Se nanoparticles under the functional capping of poly(vinylpyrrolidone) (PVP). The nanobelts obtained exhibit a quantum size effect in optical properties, showing a blue shift of the band gap and direct transitions relative to the values of bulk t-Se.

Fabrication and visible-light photocatalytic behavior of perovskite praseodymium ferrite porous nanotubes

Perovskite praseodymium ferrite (PrFeO3) porous nanotubes are prepared by electrospinning of the precursor solution into nanofibers, subsequently by annealing the precursor fibers at a low temperature (e.g. 40 °C) and finally by calcination at a high temperature. The low temperature annealing treatment is found to play a key role in the formation of porous nanotube. The porous tubes show a perovskite-type PrFeO3 crystal characteristic with high optical absorption in the UV-visible region and an energy band gap of 1.97 eV. When compared with PrFeO3 porous nanofibers and PrFeO3 particles, the PrFeO3 porous nanotubes show better visible-light photo-catalytic ability to degrade Rhodamine B in aqueous phase because of the increased surface area and more active catalytic sites on the inner walls and outer surfaces.

Investigation of the potential of plasma technology to improve the performance of solar cells

 This study explored plasma techniques to improve the efficiency of dye sensitised solar cells and perovskite solar cells. It was found that plasma functionalization of TiO2 improved dye absorption, thereby improving efficiency. Controllable nitrogen doping of TiO2 was achieved by a unique system that combines plasma with heat treatment. The doping reduced the band-gap of TiO2. A crystalline TiO2 thin film on plastic substrates was successfully achieved by a low temperature plasma method, which could potentially allow such soft and flexible substrates to be used for solar cells.