One-dimensional polyelectrolyte/polymeric semiconductor core/shell structure : sulfonated poly(arylene ether ketone)/polyaniline nanofibers for organic field-effect transistors

A polyelectrolyte/polymeric semiconductor core/shell structure is developed for organic field-effect transistors (OFETs) based on sulfonated poly(arylene ether ketone)/polyaniline core/shell nanofibers via electrospinning and solution-phase selective polymerization. The polyelectrolyte does not work as a gate dielectric, but can provide an internal modulation from the nanointerface of the 1D core/shell nanostructure. The transistor devices display very high mobilities.

Au-doped polyacrylonitrile-polyaniline core-shell electrospun nanofibers having high field-effect mobilities

Au-doped polyacrylonitrile–polyaniline core–shell nanofibers are fabricated via electrospinning and subsequent gas-phase polymerization, providing a very high field-effect mobility of up to 11.6 cm² V⁻¹ s⁻¹. This method is also suitable for other conducting polymers and may eventually lead to a new and simplified fabrication of high-performance polymer organic field-effect transistors.

Design of a high sensitive double-gate field-effect transistor biosensor for DNA detection

The study of interactions between organic biomolecules and semiconducting surfaces is an important consideration for the design and fabrication of field-effect-transistor (FET) biosensor. This paper demonstrates DNA detection by employing a double-gate field effect transistor (DGFET). In addition, an investigation of sensitivity and signal to noise ratio (SNR) is carried out for different values of analyte concentration, buffer ion concentration, pH, reaction constant, etc. Sensitivity, which is indicated by the change of drain current, increases non-linearly after a specific value (∼1nM) of analyte concentration and decreases non-linearly with buffer ion concentration. However, sensitivity is linearly related to the fluidic gate voltage. The drain current has a significant effect on the positive surface group (-NH2) compared to the negative counterpart (-OH). Furthermore, the sensor has the same response at a particular value of pH (5.76) irrespective of the density of surface group, although it decreases with pH value. The signal to noise ratio is improved with higher analyte concentrations and receptor densities.

1-Naphthyl- and mesityltellurium(IV,II) derivatives of small bite chelating organic ligands: effect of steric bulk and intramolecular secondary bonding interaction on molecular geometry and supramolecular association

The synthesis and characterization of unsymmetric diorganotellurium compounds containing a sterically demanding I-naphthyl or
mesitylligand and a small bite chelating organic ligand capable of 1,4-Te···N(O) intramolecular interaction is described. The reaction
of ArTeCl₃ (Ar = I-C_lOH₇, Np; 2,4,6-Me₃C₆H_2' Mes) with (SB)HgCI [SB = the Schiff base, 2-(4,4'-N0₂C₆H₄CH=NC₆H₃-Me)] or a methyl ketone (RCOCH₃) afforded the corresponding dichlorides (SB)ArTeCI₂ (Ar = Np, 1Aa; Mes, 1Ba) or (RCOCH₂)ArTeCl₂ (Ar = Np; R = Ph (2Aa), Me (3Aa), Np (4Aa); Ar = Mes, R = Ph (2Ba)). Reduction of 1Aa and 1Ba by Na₂S₂0₅ readily gave the tellurides (SB)ArTe (Ar = Np (1A), Mes, (1B) but that of dichlorides derived from methylketones was complicated due to partial decomposition to tellurium powder and diarylditelluride (Ar₂Te₂), resulting in poor yields of the corresponding tellurides 2A, 2B and 3A. Oxidation of the isolated tellurides with S0₂Cl₂, Br₂ and I₂ yielded the corresponding dihalides. All the synthesized compounds have been characterized with the help of IR, ¹H, ^l3C, and ¹²⁵Te NMR and in the case of 2Aa, and 2Ba by X-ray crystallography. Appearance of only one ¹²⁵Te signal indicated that the unsymmetric derivatives were stable to disproportionation to symmetric species. Intramolecular 1,4-Te· . ·0 secondary bonding interactions (SBIs) are exhibited in the crystal structures of both the tellurium(IV) dichlorides, 2Aa, and 2Ba. Steric repulsion of the mesityl group in the latter dominates over lone pair-bond pair repulsion, resulting in significant widening of the equatorial C-Te-C angle. This appears to be responsible for the lack of Te· . ·CI involved supramolecular associations in the crystal structure of 2Ba.

Performance analysis of a field-effect-transistor based aptasensor

Prostate cancer is one of the most diagnosed cancers which leads to a considerable number of deaths due to the lack of early and sensitive detection. This paper presents an aptamer functionalized field effect (FET) based biosensor for the detection of prostate cancer. Prostate specific antigen (PSA) is considered as the biomarker for prostate cancer whose detection is confirmed by attaching aptamers onto the sensor surface. Through the modelling and numerical simulation, the paper aims to evaluate and predict the performance parameters such as sensitivity, settling time, and limit of detection (LOD) of a label-free FET based electronic biosensor. Various sensor parameters such as structure (i.e., geometry), type of the FET (e.g., nanowire FET, spherical FET, ion-selective FET, and magnetic particle) radius of the FET channel and incubation time are optimized and analyzed. In addition, concentration of analyte biomolecules, diffusion coefficients and affinity to the receptor molecules are also investigated to determine the optimize performance parameters.

Molecularly engineered graphene surfaces for sensing applications: A review.

Graphene is scientifically and commercially important because of its unique molecular structure which is monoatomic in thickness, rigorously two-dimensional and highly conjugated. Consequently, graphene exhibits exceptional electrical, optical, thermal and mechanical properties. Herein, we critically discuss the surface modification of graphene, the specific advantages that graphene-based materials can provide over other materials in sensor research and their related chemical and electrochemical properties. Furthermore, we describe the latest developments in the use of these materials for sensing technology, including chemical sensors and biosensors and their applications in security, environmental safety and diseases detection and diagnosis.

Applications of electrospun nanofibers for electronic devices

In recent decades, electrospinning of nanofibers has progressed very rapidly in both scientific and technological aspects, and electrospun nanofibers have shown enormous potential for various applications. In particular, electrospun nanofibers have significantly enhanced the application performance of many electronic devices, such as solar cells, mechanical-to-electric energy harvesters, rechargeable batteries, supercapacitors, sensors, field-effect transistors, diodes, photodetectors, and electrochromic devices. This chapter provides a comprehensive summary on the recent progress in the application of electrospun nanofibers in electronic devices.

Effect of organic additives on the cycling performances of lithium metal polymer cells

Gel polymer electrolytes were prepared by immersing a porous poly(vinylidene fluoride-co-hexafluoropropylene) membrane in an electrolyte solution containing small amounts of organic additive. Three kinds of organic compounds, thiophene, 3,4-ethylenedioxythiophene and biphenyl, were used as a polymerizable monomeric additive. The organic additives were found to be electrochemically oxidized to form conductive polymer films on the electrode at high potential. By using the gel polymer electrolytes containing different organic additive, lithium metal polymer cells, composed of lithium anode and LiCoO2 cathode, were assembled and their cycling performance evaluated. Adding small amounts of a suitable polymerizable additive to the gel polymer electrolyte was found to reduce the interfacial resistance in the cell during cycling, and it thus exhibited less capacity fade and better high rate performance. Differential scanning calorimetric studies showed that the thermal stability of the fully charged LiCoO2 cathode was improved in the cell containing an organic additive.

Graphene quantum dots directly generated from graphite via magnetron sputtering and the application in thin-film transistors

This work presents a novel method to prepare graphene quantum dots (GQDs) directly from graphite. A composite film of GQDs and ZnO was first prepared using the composite target of graphite and ZnO via magnetron sputtering, followed with hydrochloric acid treatment and dialysis. Morphology and optical properties of the GQDs were investigated using a number of techniques. The as-prepared GQDs are 4-12 nm in size and 1-2 nm in thickness. They also exhibited typical excitation-dependent properties as expected in carbon-based quantum dots. To demonstrate the potential applications of GQDs in electronic devices, pure ZnO and GQD-ZnO thin-film transistors (TFTs) using ZrOx dielectric were fabricated and examined. The ZnO TFT incorporating the GQDs exhibited enhanced performance: an on/off current ratio of 1.7 × 107, a field-effect mobility of 17.7 cm2/Vs, a subthreshold swing voltage of 90 mV/decade. This paper provides an efficient, reproducible and eco-friendly approach for the preparation of monodisperse GQDs directly from graphite. Our results suggest that GQDs fabricated using magnetron sputtering method may envision promising applications in electronic devices.

Specialist training in investigative and evidential interviewing: is it having any effect on the behaviour of professionals in the field?

While numerous concerns have been voiced over the past decade regarding the inappropriate question styles of investigative and evidential interviewers, there has been relatively little research, discussion, and critique in relation to the content, structure, and efficacy of existing interviewer training courses. This article provides a brief up-to-date summary of the essential elements of an investigative or evidential interview, followed by a review of research relating to the effectiveness of training programs for forensic interviewers and the factors that are needed to promote the use of appropriate questioning techniques. Finally, this article offers recommendations for future research and for the revision of existing training programs in forensic interviewing.

Effect of oxidant type on the chemiluminescence intensity from the reaction of tris(2,2’-biyridyl)ruthenium(III) with various organic acids

An investigation into the chemiluminescence of fourteen organic acids and tris(2,2′-bipyridyl)ruthenium(II) was undertaken. Particular emphasis was placed upon the method of production of the reagent, tris(2,2′-bipyridyl)ruthenium(III), with cerium(IV) sulfate, potassium permanganate, lead dioxide and electrochemical generation. Analytically useful chemiluminescence was observed when Ce(IV) or potassium permanganate were employed as oxidants. The kinetics of analyte oxidation was related to the intensity of the chemiluminescence emission, which increased by three orders of magnitude for tartaric acid after 40 h of oxidation.

The 'filler-effect' in organic ionic plastic crystals : Enhanced conductivity by the addition of nano-sized TiO2

The addition of nano-sized ceramic particles to the plastic crystal ethyl-methyl pyrrolidinium bis(trifluoromethane sulfonyl)amide (P₁₂TFSA) has been investigated by means of DSC and conductivity. The thermal behaviour of the plastic crystal as a function of filler content suggests that the filler particles decrease the onset temperature of the melting slightly at high loadings, however they do not decrease the crystallinity of the material. Furthermore, the IV → III transition decreases in intensity, indicating that the addition of filler increases the possibility for the crystal to remain in metastable rotator phases also at lower temperatures. The conductivity shows a more than one order of magnitude increase with the addition of filler, with a filler concentration dependence that levels out above ~ 10 wt.% TiO₂.

Surprising effect of nanoparticle inclusion on ion conductivity in a lithium doped organic ionic plastic crystal

Doping lithium bis(trifluoromethanesulfonyl)amide (Li[NTf₂]) into the N-ethyl,N′-methylpyrrolidinium bis(trifluoromethanesulfonyl)amide ([C₂mpyr][NTf₂]) plastic crystal material has previously indicated order of magnitude enhancements in ion transport and conductivity over pure [C₂mpyr][NTf₂]. Recently, conductivity enhancements in this ionic plastic crystal induced by SiO₂ nanoparticles have also been reported. In this work the inclusion of SiO₂ nanoparticles in Li ion doped [C₂mpyr][NTf₂] has been investigated over a wide temperature range by differential scanning calorimetry (DSC), impedance spectroscopy, positron annihilation lifetime spectroscopy (PALS), Raman spectroscopy, NMR spectroscopy and scanning electron microscopy (SEM). Solid state ¹H NMR indicates that the addition of the nanoparticles increases the mobility of the [C₂mpyr] cation and positron lifetime spectroscopy (PALS) measurements indicate an increase in mean defect size and defect concentration as a result of nanoparticle inclusion, especially with 10 wt% SiO₂. Thus, the substantial drop in ion conductivity observed for this doped nanocomposite material was surprising. This decrease is most likely due to the decrease in mobility of the [NTf₂] anion, possibly by its adsorption at the SiO₂/grain boundary interface and concomitant decrease in mobility of the Li ion.

Effect of natural organic compounds on the removal of organic carbon in coagulation and flocculation processes

Natural organic matter (NOM) in water contains organic compounds that are both hydrophobic and hydrophilic with a wide range of molecular weights. It is composed of non-homogeneous organic compounds such as humic substances, amino acids, sugars, aliphatic and aromatic acids, and other chemical synthetic organic matters. NOM in water is a major concern not only because of its contribution to the formation of disinfection by-products (DBPs) and taste and odor, but also its influence on the demand for coagulants and disinfectants, the removal efficiency of water treatment processes, etc. This research aims at identifying the influence of NOM in coagulation and flocculation processes in order to optimize the coagulation and flocculation conditions. In this study, pretreated pond water was used as the source water. It was observed from the experimental results that: (1) The optimum pH for coagulation to remove NOM is around 7. (2) The optimum alum dose at this pH can vary from 125-1,225 mgl-1 when the TOC is increased from 4 to 25 mgl-1. (3) The presence of secondary compounds such as Ca2+, Mg2+ divalent cations had no significant effect on the removal of organic matter. (4) The presence of clay increased the organic removal by 15%. (5) The organic compound with higher molecular weight has higher removal affinity in coagulation process. (6) Floc size and settling velocity of floc and sludge production all increased with the increase in NOM concentration. From the results of Capillary Suction Time (CST) tests, the floc formed with lower TOC readily released the water to make the dewatering process easier. (7) The organic removal efficiency was significantly different for natural water containing non-homogeneous organic compounds compared to the synthetic water containing humic acid only (homogeneous organic matter). For example, the NOM removal efficiency was 80% for the synthetic water containing humic acid with TOC of 7 mgl-1 at pH 7; but the NOM removal for the pretreated pond water was 60%.