Preconcentration of phenanthrene from aqueous solution by a slightly hydrophobic nonionic surfactant

The preconcentration of phenanthrene from aqueous solution was discussed. The study was carried out by using a slightly hydrophobic nonionic surfactant. The slightly hydrophobic surfactant, at proper condition enhanced the performance of the surfactant-based extraction process on polycyclic aromatic hydrocarbons (PAH). The results show that the increasing the temperature difference enhanced the preconcentration factors prominently but only slightly the recovery efficiency.

Cloud-point extraction of phenanthrene by nonionic surfactants

Extraction and preconcentration of the model polycyclic aromatic hydrocarbon (PAH), phenanthrene, in aqueous solutions by two different kinds of nonionic ethoxylated alcohols, Tergitol 15-S-7 and Neodol 25-7, as extractants was studied at ambient temperature (22°C). Both surfactants have almost the same numbers of hydrocarbons and ethylene-oxide (EO) units, but differ in the location of the alcohols. Neodol 25-7 is a primary alcohol, while Tergitol 15-S-7 is a secondary one. The extraction process is based on the clouding phenomena of these two nonionic surfactants. Addition of sodium sulfate or sodium phosphate could decrease the cloud point temperatures of the surfactant solutions below the ambient temperatures, so that the cloud-point extraction process could be facilitated. Increasing the salt concentration or decreasing the surfactant concentration could improve the preconcentration factor, which is attributable to the decrease in the volume of surfactant-rich phase. Consequently, the recovery efficiency higher than 96% was achieved for phenanthrene in aqueous solution.

Effect of a commercial alcohol ethoxylate surfactant (C11–15E7) on biodegradation of phenanthrene in a saline water medium by Neptunomonas naphthovorans

Biodegradation of poorly soluble polycyclic aromatic hydrocarbons (PAHs) has been a challenge in bioremediation. In recent years, surfactant-enhanced bioremediation of PAH contaminants has attracted great attention in research. In this study, biodegradation of phenanthrene as a model PAHs solubilized in saline micellar solutions of a biodegradable commercial alcohol ethoxylate nonionic surfactant was investigated. The critical micelle concentration (CMC) of the surfactant and its solubilization capacity for phenanthrene were examined in an artificial saline water medium, and a type of marine bacteria, Neptunomonas naphthovorans, was studied for the biodegradation of phenanthrene solubilized in the surfactant micellar solutions of the saline medium. It is found that the solubility of phenanthrene in the surfactant micellar solutions increased linearly with the surfactant concentrations, but, at a fixed phenanthrene concentration, the biodegradability of phenanthrene in the micellar solutions decreased with the increase of the surfactant concentrations. This was attributed to the reduced bioavailability of phenanthrene, due to its increased solubilization extent in the micellar phase and possibly lowered mass transfer rate from the micellar phase into the aqueous phase or into the bacterial cells. In addition, an inhibitory effect of the surfactant on the bacterial growth at high surfactant concentrations may also play a role. It is concluded that the surfactant largely enhanced the solubilization of phenanthrene in the saline water medium, but excess existence of the surfactant in the medium should be minimized or avoided for the biodegradation of phenanthrene by Neptunomonas naphthovorans.

Effects of additives on the cloud points of selected nonionic linear ethoxylated alcohol surfactants

Effects of various additives including inorganic salts, nonionic and ionic surfactants, water-soluble polymers and alcohols on the cloud points of three linear nonionic surfactants, Tergitol 15-S-7, Tergitol 15-S-9 and Neodol 25-7, were investigated. These surfactants are readily biodegradable and either linear primary or secondary ethoxylated alcohols. Cloud points of these surfactants were functions of their concentrations and concentrations of additives. The cloud points of nonionic surfactant mixtures lay in between the cloud points of individual component surfactants. Presence of two ionic surfactants, sodium dodecyl sulfate (SDS) and cetyl trimethyl ammonium bromide (CTAB), increased the cloud point of 1 wt% Tergitol 15-S-7 micellar solution dramatically when concentrations of ionic surfactants approaching their critical micelle concentration. Addition of water-soluble polymers decreased the cloud point, while addition of inorganic salts can either increase or decrease the cloud points. However, the effect of an alcohol additive on cloud point was dependent on its chain length or its water solubility. Interestingly, synergistic effects between sulfate or phosphate and pentanol on depression of cloud points of Tergitol 15-S-9 were discovered. A linear model predicting cloud points of Tergitol 15-S-X (X = 7, 9 and 12) surfactants and Neodol 25-X (X = 7, 9 and 12) surfactants were proposed with a correlation to logarithm of their ethylene oxide numbers.

Architecture and engineering of a supramolecular functional material by manipulating the nano-structure of fiber network

Three-dimensional fiber networks were created from an organogel system consisting mainly of elongated fibrils by using a nonionic surfactant as an additive. The presence of the surfactant molecules manipulates the network structure by enhancing the mismatch nucleation on the growing fiber tips. Both the fiber network structure and the rheological properties of the material can be finely tuned by changing the surfactant concentration, which provides a robust approach to the engineering of supramolecular soft functional materials.

A novel cloud-point extraction process for preconcentrating selected polycyclic aromatic hydrocarbons in aqueous solution

A novel but simple cloud-point extraction (CPE) process is developed to preconcentrate the trace of selected polycyclic aromatic hydrocarbons (PAHs) with the use of the readily biodegradable nonionic surfactant Tergitol 15-S-7 as extractant. The concentrations of PAHs, mixtures of naphthalene and phenanthrene as well as pyrene, in the spiked samples were determined with the new CPE process at ambient temperature (23 °C) followed by high performance liquid chromatography (HPLC) with fluorescence detection. More than 80% of phenanthrene and pyrene, respectively, and 96% of naphthalene initially present in the aqueous solutions with concentrations near or below their aqueous solubilities were recovered using this new CPE process. Importantly Tergitol 15-S-7 does not give any fluorometric signal to interfere with fluorescence detection of PAHs in the UV range. No special washing step is, thus, required to remove surfactant before HPLC analyses. Different experimental conditions were studied. The optimum conditions for the preconcentration and determi nation of these selected PAHs at ambient temperature have been established as the following:  (1) 3 wt % surfactant; (2) addition of 0.5 M Na2SO4; (3) 10 min for equilibration time; and (4) 3000 rpm for centrifugal speed with duration of 10 min.

In situ synchrotron SAXS study of polymerizable microemulsions

We present for the first time a real-time small-angle X-ray scattering (SAXS) study of the structural transition of fluid microemulsion to solid polymerized material in a silicone polymerizable microemulsion system. A reactive methacrylate-terminated siloxane macromonomer (MTSM, Mn ∼ 1000 g/mol) was synthesized and used for microemulsion formulations comprising MTSM (oil phase), water, and a mixture of nonionic surfactant (Teric G9A8) with isopropanol. In situ synchrotron SAXS was used to investigate time-dependent nanostructure evolution during the polymerization reaction, which was directly initiated by X-ray radiation. The SAXS data were analyzed using both the Teubner-Strey model and the core-shell model. The results obtained by the Teubner-Strey model showed that the domain size (d) decreased while the correlation length (ξ) increased upon polymerization. The analysis in terms of the core-shell model displayed that adding water to the precursor microemulsion caused the water droplets to start swelling, which resulted in the discontinuity of water in oil microemulsion. There exhibited large differences in morphologies of polymerized materials from the microemulsion formulations with different water and surfactant contents. The core and shell sizes of water droplets decreased during the course of polymerization when there was 15 wt % or more water in the microemulsion formulation; the polymerized material thus exhibited increasingly discrete granular morphology. When there was 10 wt % or less water content in the precursor microemulsion, the rearrangement of water domains could be minimized during the course of polymerization and transparent polymerized material was obtained.

Controlling morphology and porosity of porous siloxane membranes through water content of precursor microemulsion

Here we report a facile method for controlling the morphology and porosity of porous siloxane membranes through manipulation of the water content of precursor microemulsions. The polymerizable microemulsion precursors consisted of a methacrylate-terminated siloxane macromonomer (MTSM) as the oil phase, nonionic surfactant (Teric G9A8), water, and cosurfactant (isopropanol). Photo-polymerization of the oil phase in the parent microemulsion solutions resulted in polymeric solids, and subsequent removal of the extractable components yielded porous PDMS membranes. The pre-cured parent microemulsion solutions and post-cured polymers were characterized by small angle X-ray scattering (SAXS) while the nanostructures of extracted porous polymer membranes were characterized by SAXS, scanning electron microscopy (SEM) and mercury porosimetry. The results indicated that nano- and micro-structures of the membranes could be modulated by the water content of the precursor microemulsions. Further, in situ photo-rheometry was used to follow the microemulsion polymerization process. The rate of polymerization and the mechanical properties of the resulting PDMS membranes also depend on the water content of precursor microemulsions. This study demonstrates a simple approach to the fabrication of a variety of novel porous PDMS membranes with controllable morphology and porosity.

Effects of polymer concentration and cationic surfactant on the morphology of electrospun polyacrylonitrile nanofibres

PAN nanofibres were prepared via an electrospinning process. The effect of polymer concentration on the fibre morphology was studied. At a very dilute solution, no fibres were obtained in the electrospinning process. As the concentration increased, the fibre morphology evolved from a beads-on-string structure to a uniform fibre structure with increasing fibre diameters. However, when the same electrospinning process was conducted with the addition of a cationic surfactant, the formation of disconnected beads was prevented, and the number of beads-on-string structures reduced significantly. In addition, the presence of cationic surfactant reduced the average diameter of the electrospun PAN nanofibres.

Role of water and surfactant in the solvent milling of wool

Unlike other fibres, wool felts readily when agitated in the presence of water. For this reason, only the minimum necessary quantity of water is used when the garments are drycleaned. However, wool fibres are often deliberately felted to obtain a warm bulky handle by controlled addition of water to the solvent. This process is known as solvent milling and recently, it has become a popular alternative to the traditional milling in water alone. Although the factors which influence milling in solvent are known, the relationships between them are not well defined. A comprehensive study of the relationship between water distribution and milling shrinkage during agitation of wool in perchloroethylene has been carried out in this thesis. The Karl Fischer method of determination was used throughout to establish the distribution of water between the wool fibre and the solvent liquor. The emphasis was placed on practical production variables. The role of surfactant in affecting milling shrinkage through its effect on the transport of water to the fibre from the solvent was examined. The ability of a suitable surfactant in promoting even and rapid sorption of water by the fibre was related to the colloidal properties of the milling liquor.

The miscibility of poly(d,l-lactide-co-glycolide) with amphiphilic molecules and the interaction of their mixtures with DNA at air/water interface

The miscibility of poly(d,l-lactide-co-glycolide) (PLG) with three amphiphilic molecules and the interaction of the PLG/surfactant mixtures with DNA at air/water interface are investigated by π-A isotherms, Brewster angle microscopy (BAM) and atomic force microscopy (AFM) techniques. The π-A isotherms of the PLG mixtures with cationic C12AzoC6PyBr, and C12AzoC6N(CH3)3Br, are quite different from the π-A isotherm of pure PLG on water subphase. In contrast to the case, the π-A isotherm of PLG mixed with nonionic C12AzoC6OPy is almost identical to the pure PLG except some increasing of molecular area. Similar phenomena are observed on DNA subphase. The in situ BAM and ex situ AFM observations demonstrate that the dispersion of PLG at air/water interface becomes good when it mixes with the two cationic surfactants, whereas quite poor due to the phase separation when it mixes with the nonionic amphiphilic molecule. Based on these results we conclude that the cationic surfactants can affect the conformation change of PLG at air/water interface and figure a well miscibility with polymer whereas the nonionic amphiphilic molecule presents poor miscibility. In addition, the even mixing of the PLG and the cationic surfactants is favorable for the adsorption to DNA more effectively.

Surfactant-mediated biodegradation of polycyclic aromatic hydrocarbons

Polycyclic aromatic hydrocarbons (PAHs) are toxic environmental pollutants that are known or suspected carcinogens or mutagens. Bioremediation has been used as a general way to eliminate them from the contaminated sites or aquifers, but their biodegradation is rather limited due to their low bioavailability because of their sparingly soluble nature. Surfactant-mediated biodegradation is a promising alternative. The presence of surfactants can increase the solubility of PAHs and hence potentially increase their bioavailability. However, inconclusive results have been reported on the effects of surfactant on the biodegradation of PAHs. In this work, surfactant-mediated biodegradation of PAHs is reviewed.