An improved understanding of the dispersion of multi-walled carbon nanotubes in non-aqueous solvents

The homogeneous and stable dispersion of carbon nanotubes (CNTs) in solvents is often a prerequisite for their use in advanced materials. Dispersion procedures, reagent concentration as well as the interactions among reagent, defective CNTs and near-perfect CNTs will affect the resulting CNT dispersion properties. This study, for the first time, presents a detailed comparison between two different approaches for dispersing CNTs. The results enhance our understanding of the interactions between surfactant, defective CNTs and near-perfect CNTs and thus provide insight into the mechanism of CNT dispersion. Dispersions of "as-produced" short multi-walled carbon nanotubes (MWCNTs) in N,N-dimethylformamide were prepared by two different surfactant (Triton X-100) assisted methods: ultrasonication and ultrasonication followed by centrifugation, decanting the supernatant and redispersing the precipitate. Visual observation and UV-visible spectroscopy results showed that the latter method produce a more stable dispersion with higher MWCNT content compared to dispersions produced by ultrasonication alone. Transmission electron microscopy and Raman spectroscopic investigations revealed that the centrifugation/ decanting step removed highly defective nanotubes, amorphous carbon and excess surfactant from the readily re-dispersible near-perfect CNT precipitate. This is contrary to other published findings where the dispersed MWCNTs were found in the supernatant. Thermogravimetric analysis showed that 95 % of Triton X-100 was removed by centrifugation/decanting step, and the remainder of the Triton X-100 molecules is likely randomly adsorbed onto the MWCNT surface. Infrared spectral analysis suggests that the methylene groups of the polyoxyethylene (aliphatic ether) chains of the residual Triton X-100 molecules are interacting with the MWCNTs. © 2014 Springer Science+Business Media.

Substrate-induced coagulation (SIC) of nano-disperse carbon black in non-aqueous media : a method of manufacturing highly conductive cathode materials for Li-ion batteries by self-assembly

Substrate-induced coagulation (SIC) is a coating process based on self-assembly for coating different surfaces with fine particulate materials. The particles are dispersed in a suitable solvent and the stability of the dispersion is adjusted by additives. When a surface, pre-treated with a flocculant e.g. a polyelectrolyte, is dipped into the dispersion, it induces coagulation resulting in the deposition of the particles on the surface. A non-aqueous SIC process for carbon coating is presented, which can be performed in polar, aprotic solvents such as N-Methyl-2- pyrrolidinone (NMP). Polyvinylalcohol (PVA) is used to condition the surface of substrates such as mica, copperfoil, silicon-wafers and lithiumcobalt oxide powder, a cathode material used for Li-ion batteries. The subsequent SIC carbon coating produces uniform layers on the substrates and causes the conductivity of lithiumcobalt oxide to increase drastically, while retaining a high percentage of active battery material.

Microbial lipases : at the interface of aqueous and non-aqueous media: a review

In recent times, biotechnological applications of microbial lipases in synthesis of many organic molecules have rapidly increased in non-aqueous media. Microbial lipases are the working horses' in biocatalysis and have been extensively studied when their exceptionally high stability in non-aqueous media has been discovered. Stability of lipases in organic solvents makes them commercially feasibile in the enzymatic esterification reactions. Their stability is affected by temperature, reaction medium, water concentration and by the biocatalyst's preparation. An optimization process for ester synthesis from pilot scale to industrial scale in the reaction medium is discussed. The water released during the esterification process can be controlled over a wide range and has a profound effect on the activity of the lipases. Approaches to lipase catalysis like protein engineering, directed evolution and metagenome approach were studied. This review reports the recent development in the field of non-aqueous microbial lipase catalysis and factors controlling the esterification/transesterification processes in organic media.

Molecular dynamics simulations of highly concentrated salt solutions : structural and transport effects in polymer electrolytes

Structural, thermodynamic and transport properties have been calculated in concentrated non-aqueous NaI solutions using molecular dynamics simulations. Although the solvent has been represented by a simplistic Stockmayer fluid (spherical particles with point dipoles), the general trends observed are still a useful indication of the behavior of real non-aqueous electrolyte systems. Results indicate that in low dielectric media, significant ion pairing and clustering occurs. Contact ion pairs become more prominent at higher temperatures, independent of the dielectric strength of the solvent. Thermodynamic analysis shows that this temperature behavior is predominantly entropically driven. Calculation of ionic diffusivities and conductivities in the NaI/ether system confirms the clustered nature of the salt, with the conductivities significantly lower than those predicted from the Nernst-Einstein relation. In systems where the solvent-ion interactions increase relative to ion-ion interactions (lower charge or higher solvent dipole moment), less clustering is observed and the transport properties indicate independent motion of the ions, with higher calculated conductivities. The solvent in this system is the most mobile species, in comparison with the polymer electrolytes where the solvent is practically immobile.

Acid–organic base swollen polymer membranes

In this work, two different polymer membrane systems based on Nafion and Teflon were investigated as proton conductors for polymer membrane fuel cells. Water-free Nafion117 membranes swollen with different non-aqueous solvents were prepared. The solvents included imidazole, imidazole–imidazolium salt solutions, room temperature molten salts and molten salt–acid solutions. Teflon films were treated with a surfactant, or a Nafion solution, to improve their surface properties, and were subsequently swollen with phosphoric acid. Conductivity measurements were carried out on both the Nafion and Teflon membranes. Conductivities in the range of 10⁻³ S cm⁻¹ at around 100°C were obtained. This is still an order of magnitude lower than the corresponding water swollen Nafion at 80°C.

Synthesis of ethyl acetate employing celite-immobilized lipase of Bacillus cereus MTCC 8372

A wide range of fatty acid esters can be synthesized by esterification and transesterification reactions catalyzed by lipases in non-aqueous systems. In the present study, immobilization of a purified alkaline extra-cellular lipase of Bacillus cereus MTCC 8372 by adsorption on diatomaceous earth (celite) for synthesis of ethyl acetate via transesterification route was investigated. B. cereus lipase was deposited on celite (77% protein binding efficiency) by direct binding from aqueous solution. Immobilized lipase was used to synthesis of ethyl acetate from vinyl acetate and ethanol in n -nonane. Various reaction conditions, such as biocatalyst concentration, substrates concentration, choices of solvents ( n -alkanes), incubation time, temperature, molecular sieves (3Å × 1.5 mm), and water activity(a _w ), were optimized. The immobilized lipase (25 mg/ml) was used to perform transesterification in n -alkane(s) that resulted in approximately 73.7 mM of ethyl acetate at 55 °C in n -nonane under shaking (160 rpm) after 15 h, when vinyl acetate and ethanol were used in a equimolar ratio (100 mM each). Addition of molecular sieves (3Å × 1.5 mm) as well as effect of water activity of saturated salt solutions (KI, KCl and KNO ₃ ) to the transesterification efficiency has inhibitory effect. Batch operational stability tests indicated that immobilized lipase had retained 50% of its original catalytic activity after four consecutive batches of 15 h each.

Simultaneous synthesis of gold nanoparticles and conducting poly(3,4-ethylenedioxythiophene) towards optoelectronic nanocomposites

In this paper, a new method for obtaining poly(3,4-ethylenedioxythiophene) (PEDOT/PSS)/gold nanocomposites is described. In a first step, PEDOT/PSS gold nanoparticle aqueous dispersions were obtained by simultaneous chemical synthesis of PEDOT and gold nanoparticles in the presence of PSS that acts as a stabilizer. In a second step, these PEDOT/PSS gold nanoparticle dispersions were used to formulate nanocomposites by mixing the initial dispersion with commercially available PEDOT/PSS aqueous dispersion. Nanocomposite thin films, obtained by casting these dispersions, present an intimate contact between the inorganic and organic components

Rechargeable Zn/PEDOT battery with an imidazolium-based ionic liquid as the electrolyte

 A non-aqueous secondary battery has been constructed by using Zn metal as the anode and chemically synthesised PEDOT as the cathode, with a 1-ethyl-3-methylimidazolium dicyanamide ionic liquid as the electrolyte, which avoids dendritic growth processes on the Zn surface upon charge/discharge cycling. The novel Zn/PEDOT rechargeable cell shows high efficiency and cycling ability, performing over 320 cycles with no indication of short circuit. Both the Zn and PEDOT surfaces showed minimal signs of degradation, suggesting that a Zn/PEDOT electrochemical device would be capable of extended cycle life under numerous charge/discharge cycles.

Parametric investigation of batch adsorption of proteins onto polymeric particles

Background: Effective bimolecular adsorption of proteins onto solid matrices is characterized by in-depth understanding of the biophysical features essential to optimize the adsorption performance. Results: The adsorption of bovine serum albumin (BSA) onto anion-exchange Q-sepharose solid particulate support was investigated in batch adsorption experiments. Adsorption kinetics and isotherms were developed as a function of key industrially relevant parameters such as polymer loading, stirring speed, buffer pH, protein concentration and the state of protein dispersion (solid/aqueous) in order to optimize binding performance and adsorption capacity. Experimental results showed that the first order rate constant is higher at higher stirring speed, higher polymer loading, and under alkaline conditions, with a corresponding increase in equilibrium adsorption capacity. Increasing the stirring speed and using aqueous dispersion protein system increased the adsorption rate, but the maximum protein adsorption was unaffected. Regardless of the stirring speed, the adsorption capacity of the polymer was 2.8 mg/ml. However, doubling the polymer loading increased the adsorption capacity to 9.4 mg/ml. Conclusions: The result demonstrates that there exists a minimum amount of polymer loading required to achieve maximum protein adsorption capacity under specific process conditions.

Oxygen reduction reaction in ionic liquids: an overview

The oxygen reduction reaction has been the subject of intensive research during decades due to their importance in life processes such as biological respiration, and also as a cathodic process in energy storage devices (e.g. fuel cells and air batteries). Detailed reviews on the oxygen reduction reaction in aqueous and non-aqueous media are available in the literature but it is lacking in the case of ionic liquids. Therefore a comprehensive review on the oxygen reduction reaction (ORR) in ionic liquids is described in this chapter in order to compile the state of the art from a fundamental point of view and improve the current knowledge towards not only fundamental but also practical applications. The oxygen reduction reaction mechanism in neat imidazolium, pyrrolidinium, quaternary ammonium, and phosphonium-based ionic liquids, which mainly undergo one-electron pathway leading to the generation of superoxide anion (O2•-), is the main topic of this chapter. The reversibility of the O2/O2•- redox couple is highly dependent on the composition of the ionic liquid, as an example superoxide is more stable in the presence of aliphatic and alicyclic cations than in the presence of aromatic rings. Furthermore, the influence of protic and aprotic additives in the ORR mechanism is also explained in this chapter together with the influence in electrochemical parameters such as formal potential, E0'.

Strain sensors with adjustable sensitivity by tailoring the microstructure of graphene aerogel/PDMS nanocomposites

Strain sensors with high elastic limit and high sensitivity are required to meet the rising demand for wearable electronics. Here, we present the fabrication of highly sensitive strain sensors based on nanocomposites consisting of graphene aerogel (GA) and polydimethylsiloxane (PDMS), with the primary focus being to tune the sensitivity of the sensors by tailoring the cellular microstructure through controlling the manufacturing processes. The resultant nanocomposite sensors exhibit a high sensitivity with a gauge factor of up to approximately 61.3. Of significant importance is that the sensitivity of the strain sensors can be readily altered by changing the concentration of the precursor (i.e., an aqueous dispersion of graphene oxide) and the freezing temperature used to process the GA. The results reveal that these two parameters control the cell size and cell-wall thickness of the resultant GA, which may be correlated to the observed variations in the sensitivities of the strain sensors. The higher is the concentration of graphene oxide, then the lower is the sensitivity of the resultant nanocomposite strain sensor. Upon increasing the freezing temperature from −196 to −20 °C, the sensitivity increases and reaches a maximum value of 61.3 at −50 °C and then decreases with a further increase in freezing temperature to −20 °C. Furthermore, the strain sensors offer excellent durability and stability, with their piezoresistivities remaining virtually unchanged even after 10 000 cycles of high-strain loading−unloading. These novel findings pave the way to custom design strain sensors with a desirable piezoresistive behavior.

Dispersion of boron nitride nanotubes in aqueous solution with the help of ionic surfactants

We report that ammonium oleate surfactants can help the dispersion of multiwalled boron nitride nanotubes (BNNTs) in water to form a BNNT solution stable for several months, which was due to the non-covalent functionalization of nanotube surfaces. Fourier Transform Infrared Spectroscopy (FTIR) and Photoluminescence (PL) analysis with synchrotron radiation source revealed that this BNNT aqueous solution preserves the intrinsic optical properties of BNNTs. © 2009 Elsevier Ltd. All rights reserved.