Small, tiny, minute : the appeal of the miniature

 This article reviews miniature forms appearing in museum and site collections, from the mundane to the precious to the fantastical, and suggests that their attraction is grounded in the playful sense of control they evoke in humans.

Design of a miniature UHF PIFA for DBS implants

This paper presents design and simulation of a miniature rectangular spiral planar inverted-F antenna (PIFA) at UHF RFID band (902.75 - 927.25 MHz) for integration in batteryless deep brain stimulation implants. Operation in the UHF band offers small antenna size and longer transmission range. The proposed antenna has the dimensions of 10 mm × 11.5 mm × 1.6 mm, resonance frequency of 920 MHz with a bandwidth of 18 MHz at return loss of -10 dB. A dielectric substrate of FR-4 of εr = 4.5 and δ = 0.018 with thickness of 1.5644 mm is used in this design. The resonance, radiation characteristics as well as the specific absorption rate distribution induced by the designed antenna within a four layer spherical head model is evaluated by using electromagnetic modeling software which employs the finite element method.

Rectenna circuits for RF energy harvesting in miniature DBS devices.

 Development of an optimum rectenna for radio frequency energy harvesting in miniature head-mountable deep brain stimulation (DBS) devices. The designed miniature rectenna can operate a DBS device without battery for murine preclinical research. The battery-less operation of the device eliminates battery related difficulties.

A miniature energy harvesting rectenna for operating a head-mountable deep brain stimulation device

This paper presents design, implementation, and evaluation of a miniature rectenna for energy harvesting applications. The rectenna produces DC power from a distant microwave energy transmitter. The generated DC power is then utilized to operate a head-mountable deep brain stimulation device. The rectenna consists of a miniature three-layer planar inverted-F antenna and a Schottky-diode-based bridge rectifier. The antenna has a volume of π × 6 × 1.584 mm3, a resonance frequency of 915 MHz with a simulated bandwidth of 18 MHz (907-925 MHz), and a measured bandwidth of 18 MHz (910-928 MHz) at the return loss of -10 dB. A dielectric substrate of FR-4 of εr = 4.5 and δ = 0.02 is used for simulation and fabrication of the antenna and the rectifier due to its low cost. An L-section impedance matching circuit is employed between the antenna and the rectifier to reduce the mismatch loss. The impedance matching circuit operates as a low-pass filter eliminating higher order harmonics. A deep brain stimulation device is successfully operated by the rectenna at a distance of 20 cm away from a microwave energy transmitter of power 26.77 dBm. The motivation of this paper includes creation of a deep brain stimulation device that operates indefinitely without a battery. From the application standpoint, the developed energy harvesting rectenna facilitates long-term deep brain stimulation of laboratory animals for preclinical research investigating neurological disorders.

Development and validation of a miniature programmable tDCS device

Research is being conducted on the use of transcranial direct current stimulation (tDCS) for therapeutic effects, and also on the mechanisms through which such therapeutic effects are mediated. A bottleneck in the progress of the research has been the large size of the existing tDCS systems which prevents subjects from performing their daily activities. To help research into the principles, mechanisms, and benefits of tDCS, reduction of size and weight, improvement in simplicity and user friendliness, portability, and programmability of tDCS systems are vital. This paper presents a design for a low-cost, light-weight, programmable, and portable tDCS device. The device is head-mountable and can be concealed in a hat and worn on the head by the subject while receiving the stimulation. The strength of the direct current stimulation can be selected through a simple user interface. The device is constructed and its performance evaluated through bench and in vivo tests. The tests validated the operation of the device in inducing neuromodulatory changes in primary motor cortex, M1, through measuring excitability of dominant M1 of resting right first dorsal interosseus muscle by transcranial magnetic stimulation induced motor evoked potentials. It was observed that the tDCS device induced comparable neuromodulatory effects in M1 as the existing bulky tDCS systems.

Aerobic fermentation of saccharomeyes cerevisae in a miniature bioreactor made of low cost poly(methylmethacrylate) (PMMA) and poly(Dimethylsiloxane) (PDMS) polymers

In this paper, a minibioreactor platform made of low cost polymers is presented. The minibioreactor prototype was designed as an alternative solution for carrying out microbial fermentation experiments in laboratory. The minibioreactor prototype has a working volume of 1.5 mL and was fabricated from poly(methylmethacrylate) (PMMA) and poly(dimethylsiloxane) (PDMS) polymers. Cell density was measured online whilst agitation rates and the temperature of the reactor content can be tightly controlled to desired set-point values. As proof-of-concept, various S. cerevisae fermentation experiments were conducted. In every experiment, the minibioreactor operated stably for the entire length of operation which was nearly 40 h with very minimal volume loss i.e. about 2.8 μ·h-1 at 37°C. The minibioreactor has the maximum oxygen transfer rate (OTR) of 16.6 mmol·L-1·h-1 under the agitation rate of 300 rpm. Under these conditions, cell specific growth rate as high as 0.291 h-1 was obtained. The experimental data in the minibioreactor operation was also reproducible using shake flask where similar growth profiles were attained under a similar growth conditions.

A miniature neural recording device

This paper presents a portable neural recording device for use with laboratory animals. It can detect and record neural signals from the cortical region of the brain during pre-clinical trials. The device utilizes simplified circuitry to perform signal detection, filtering, sampling, and storage. It includes analog and digital components each implemented on a separate small printed circuit board. The two printed circuit boards are then attached to one another to form the device. It is capable of uninterrupted operation for over 2 hours on a single coin battery. A bench-testing of the device was performed with pre-recorded neural signal which then injected to the input of the device to give validation of efficient operation of the device. Its amplification and filtration features have been analyzed. An overall 56 dB amplification and filtration in the frequency range of 300 Hz to 4 KHz was achieved. Sampling and storage at a reduced power and computational load is demonstrated with uninterrupted storage of the neural signal. A comparison of the input and reconstructed neural signals shows minimal variation error.

Performance evaluation of 3D printed miniature electromagnetic energy harvesters driven by air flow

As a renewable and non-polluting energy source, wind is used to produce electricity via large-diameter horizontal or vertical axis wind turbines. Such large wind turbines have been well designed and widely applied in industry. However, little attention has been paid to the design and development of miniature wind energy harvesters, which have great potential to be applied to the HVAC (heating, ventilating and air conditions) ventilation exhaust systems and household personal properties. In this work, 10 air-driven electromagnetic energy harvesters are fabricated using 3D printing technology. Parametric measurements are then conducted to study the effects of (1) the blade number, (2) its geometric size, (3) aspect ratio, presence or absence of (4) solid central shaft, (5) end plates, and (6) blade orientation. The maximum electrical power is 0.305 W. To demonstrate its practical application, the electricity generated is used to power 4 LED (light-emitting diode) lights. The maximum overall efficiency ηmax is approximately 6.59%. The cut-in and minimum operating Reynolds numbers are measured. The present study reveals that the 3D printed miniature energy harvesters provide a more efficient platform for harnessing ‘wind power’.

Numerical investigation of a trapped vortex miniature ramjet combustor

The design of a miniature ramjet combustor using gaseous methane fuel for Mach 2.5 has been conducted. The main challenges stem mainly from the insufficient space for mixing and burning, short residence time, and the flame stabilization. Impossible utilization of relatively large air-blast fuel injectors provides more difficulties for the design. The trapped vortex combustor, as a novel way of flameholding by trapping the pilot flame inside a cavity instead of exposing it to the mainstream, is selected. Three main parts are studied numerically, which include the cold flowfield characteristics, the fuel-injection schemes, and the overall combustion performance. The results show that the drag coefficient can helptodetermine the optimum cavity size for trappingastable vortex. Injecting all the fuel inthe cavity always leads to an overly fuel-rich condition, whereas injecting in front of the cavity with a momentum flux ratio q between 0.61 and 1.0 can successfully achieve stoichiometric mixing in the cavity. However, compared to nonreacting fuel mixing, the combustion performance is found to be more sensitive to the value of q. Among the cases studied, the one with a small q of about 0.61 has more intense pilot flames andshorter main combustor flames. The effectsofangled injection, upstream injection location, and the combustor length based on the found q are also investigated.

Integrated microfluidic drug delivery devices : a component view

Research on drug delivery devices is progressing rapidly with the main objective being the delivery of precise quantity of drugs into the target area of the body. A drug delivery device (DDD) needs to accurately control the flow rate of drug delivery and protects the body from undesired additional doses. An integrated microfluidic drug delivery device (IMDDD) is a miniature device that can regulate and monitor the delivery of the right amount of drug using micro-scale components. IMDDDs offer several advantages including ease of use, electro-chemical controllability, low power consumption, simplicity, fast fabrication, and good bio-compatibility. Various IMDDDs have been developed for treatment of cancer, cardiovascular disorder, eye and brain diseases, stress, and diabetes. This paper presents a generic architecture for IMDDDs, discusses the existing drug delivery methods, summarizes the specifications of the components, and identifies a number of performance evaluation parameters. The operation of IMDDDs is presented through fourteen potential internal components. In addition, recommendations on how enhance the design and fabrication process of IMDDDs are given.

Souvenirs of the senses - Handdunes

This series of works "Handunes" were in response to a curatorial premise that my colleagues, Patrick West and Valerie Jeremijenko produced for a invited workshop and in tensive fabrication. The premise was to re-think the notion of the souvenir and how things are mad in a place by starting with a sensation of place and building an object (reverse engineering it) from that sensation or experience. this works against the notion of an miniature icon. these objects and documented processes were exhibited at the end of the one week intensive workshop.