Mechanical behaviour of irregular fibre materials

This work investigates the effect of fibre irregularities on the mechanical behaviour of the irregular fibres using the finite element method (FEM). The first part of this work examines that the effect of fibre dimensional irregularities on the linear and non-linear tensile behaviour of the fibres, using a two-dimensional (2D) finite element models. In the linear simulation, a concept of method Young’s modulus is introduced. The method Young’s modulus, breaking load and breaking extension are affected by the magnitude and frequency of diameter variation in the fibre specimen. Fibre dimensional variation and the gauge length effect are also simulated. In the non-linear analysis, some additional information is obtained on changes in the yield and post-yield regions, which are clearly shown in the load-extension curves. Further investigation is focused on the flexural buckling behaviour of fibres with dimensional irregularities. A three-dimensional (3D) finite element model is used to simulate the buckling deformation of dimensionally irregular fibres, and the critical buckling load of the simulated fibre is calculated. Two parameters, the effective length and the average diameter within the effective length of an irregular fibre, are considered to be the key factors that influence the buckling behaviour of the fibre. An important aspect of this work is the calculation of the effective length of an irregular fibre specimen during buckling. This method has not been reported before. The third part of this work is on the combined tensile and torsional behaviour of fibres with dimensional irregularities, using a three-dimensional (3D) finite element model. Two types of fibres, polyester and wool, are simulated with sine waves of different level (magnitude) and frequency at different twist levels. For the polyester fibre, experiment verification of the simulation results has been carried out, and the results indicate the FE model is well acceptable for the simulation. The final part of this work examines the combined effect of dimensional and structural irregularities on the fibre tensile behaviour. Three-dimensional (3D) finite element models are used to simulate the cracks (transverse, longitudinal, combined transverse and longitudinal cracks) and cavities distributed in uniform fibres and fibres with 30% level of diameter variation, respectively. One of important conclusions is that under the simulated conditions, the dimensional irregularity of fibre influences the tensile behaviour of fibres more than the fibre structural irregularity. The fibre dimensional irregularity affects not only the values of the breaking load and breaking extension, but also the shape of load-extension curves. However, the fibre structural irregularity simulated in the study appears to have little effect on the shape of the load-extension curves. In addition, the effect of crack or cavity size, type and distribution on fibre tensile properties is also investigated.

Debond detection in RC structures using piezoelectric materials

This paper presents a technique to detect the delamination between the steel bars and concrete in the reinforced concrete structures. The piezoelectric components are mounted on reinforcing bars that are embedded in RC structures as sensors and actuators to generate and record the signal, which is sensitive to the delamination between the steel bars and concrete. The experimental study is carried out on a concrete slab with different debonds between the rebars and concrete. The test results show that the delamination between the rebars and concrete can be detected with the embedded piezoelectric sensors and actuators.

Mg-Zr-Sr alloys as biodegradable implant materials

Novel Mg–Zr–Sr alloys have recently been developed for use as biodegradable implant materials. The Mg–Zr–Sr alloys were prepared by diluting Mg–Zr and Mg–Sr master alloys with pure Mg. The impact of Zr and Sr on the mechanical and biological properties has been thoroughly examined. The microstructures and mechanical properties of the alloys were characterized using optical microscopy, X-ray diffraction and compressive tests. The corrosion resistance was evaluated by electrochemical analysis and hydrogen evolution measurement. The in vitro biocompatibility was assessed using osteoblast-like SaOS2 cells and MTS and haemolysis tests. In vivo bone formation and biodegradability were studied in a rabbit model. The results indicated that both Zr and Sr are excellent candidates for Mg alloying elements in manufacturing biodegradable Mg alloy implants. Zr addition refined the grain size, improved the ductility, smoothed the grain boundaries and enhanced the corrosion resistance of Mg alloys. Sr addition led to an increase in compressive strength, better in vitro biocompatibility, and significantly higher bone formation in vivo. This study demonstrated that Mg–xZr–ySr alloys with x and y ⩽5 wt.% would make excellent biodegradable implant materials for load-bearing applications.

Understanding in-vivo abrasion fatigue or common suture materials used in arthroscopic and open shoulder surgery

In orthopaedic surgery the reattachment of tendon to bone requires suture materials that have stable and durable properties to allow healing at the tendon-bone interface. Failure rates of this type of surgery can be as high as 25%. While the tissue suture interface is a weak link, proportions of these failures are caused by in-vivo abrasion of the suture with bone and suture anchor materials. Abrasion of the suture material results from the movement of the suture through the eyelet by the surgeon during surgery, or with limb movement after surgery as the suture is not rigidly restrained within the eyelet. During movement the suture is subjected to bending and frictional forces that can lead to fatigue induced failure. This paper investigates the mechanism of bending abrasion fatigue induced failure of number two grade braided sheath only and braided sheath/multifilament core sutures. Sutures were oscillated over a stainless steel wire at low frequency under load in a dry state to simulate the bending and frictional forces between suture and eyelet. Failure mechanism was determined by video microscopy of the suture during abrasion combined with optical microscopy analysis of partially and fully abraded sutures. Braided only structures had high friction loading on the small number of fibres at the abrasion interface. This caused rapid single fibre breakages that accumulate to cause suture failure. The addition of ultra-high molecular weight polyethylene core fibres to a braided suture distributed the applied load across multiple fibres at the abrasion interface. This improved abrasion resistance by 15-20 times that of braided sheath alone.

Potential of 129Xe NMR spectroscopy of adsorbed xenon for testing the chemical state of the surface of mesoporous carbon materials illustrated by the example of aggregates of diamond and onion-like carbon nanoparticles

The chemical shift in the 129Xe NMR spectrum of adsorbed xenon is very sensitive to the presence of oxygen-containing functional groups on the surface of mesoporous carbon materials. Well-characterized, structurally similar nanodiamond and onion-like carbon samples are considered here as model objects.

Improved contact load-bearing capacity of ultra-fine grained titanium : Multilayering and grading

The contact load-bearing response and surface damage resistance of multilayered hierarchical structured (MHSed) titanium were determined and compared to monolithic nanostructured titanium. The MHS structure was formed by combining cryorolling with a subsequent Surface Mechanical Attrition Treatment (SMAT) producing a surface structure consisted of an outer amorphous layer containing nanocrystals, an inner nanostructured layer and finally an ultra-fine grained core. The combination of a hard outer layer, a gradual transition layer and a compliant core results in reduced indentation depth, but a deeper and more diffuse sub-surface plastic deformation zone, compared to the monolithic nanostructured Ti. The redistribution of surface loading between the successive layers in the MHS Ti resulted in the suppression of cracking, whereas the monolithic nanograined (NG) Ti exhibited sub-surface cracks at the boundary of the plastic strain field. Finite element models with discrete layers and mechanically graded layersrepresenting the MHS system confirmed the absence of cracking and revealed a 38% decrease in shear stress in the sub-surface plastic strain field, compared to the monolithic NG Ti. Further, the mechanical gradation achieves a more gradual stress distribution which mitigates the interface failure and increases the interfacial toughness, thus providing strong resistance to loading damage. © 2014 Elsevier Ltd.

Highly sensitive SnO2 nanofiber chemiresistors with a low optimal operating temperature: synergistic effect of Cu2+/Au co-doping

Metal oxide chemiresistors (MOCs) with a low optimal operating temperature, high sensitivity and fast response/recovery are highly promising for various applications, but remain challenging to realize. Herein, we demonstrate that SnO2 nanofibers after being co-doped with Cu2+ and Au show considerably enhanced sensing performances at an unexpectedly decreased operating temperature. A synergistic effect occurs when the two dopants are introduced together. Co-doping may form a novel strategy to the development of ultrasensitive MOCs working at a low optimal temperature. This journal is © the Partner Organisations 2014.

Evaluation of FRP concrete compression member under repeated load and harsh environment

Strengthening and rehabilitation have been increasingly applied in many structures to improve their capacity and serviceability. Fiber Reinforced Polymer (FRP) materials are universally known for their ability to improve the load capacity of damaged structural elements because of their high linear-elastic behavior. However, enhancing the capacity of structural elements that are exposed to repeated load coupled with harsh environment is an area that requires further investigation. This research focused on experimental analysis of the behavior and response of confined and unconfined concrete compression members (300mm x 150mm) under repeated load while exposed to 1440 cycles of seawater splash zone in United Arab Emirates (UAE). Confining concrete compression members with Carbon Fiber Reinforced Polymer (CFRP) and Glass Fiber Reinforced Polymer (GFRP) sheets have increased the load capacity compared to the control sample at room temperature by 110% and 84%, respectively. Results showed that the average value of compressive strength for the confined concrete exposed to sea water splash zone conditions for CFRP and GFRP specimens has decreased by 33% and 23%, respectively, compared to the confined concrete in the room temperature. However, GFRP specimens showed higher performance in compressive strength under sea water splash zone than those of the CFRP specimens. Different mode of failures such as delamination, de-bonding and combination of such modes were observed and related to various exposure factors and mechanical properties.

Self-assembly of ultrathin gold nanowires and single walled carbon nanotubes as a highly sensitive substrate for surface enhanced Raman spectroscopy

Here we report self-assembly of ultrathin gold nanowires and single-walled carbon nanotubes with an ultrahigh aspect ratio as a highly sensitive substrate for surface enhanced Raman spectroscopy. And we demonstrated that the hybrids were especially efficient in adsorption of aromatic molecules such as 4-mercaptobenzoic acid and the hybrids materials could be used as a novel platform for trace level detection in the verification of paper notes through the Raman enhancement technique.