The effect of laser power density on the fatigue life of laser-shock-peened 7050 aluminium alloy

Laser shock peening (LSP) is an innovative surface treatment method that can result in significant improvement in the fatigue life of many metallic components. The process produces very little or no surface profile modification while producing a considerably deeper compressive residual stress layer than traditional shot peening operations. The work discussed here was designed to: (a) quantify the fatigue life improvement achieved by LSP in a typical high strength aircraft aluminium alloy and (b) identify any technological risks associated with its use. It is shown that when LSP conditions are optimal for the material and specimen configuration, a —three to four times increase in fatigue life over the as-machined specimens could be achieved for a representative fighter aircraft loading spectrum when applied at a representative load level. However, if the process parameters are not optimal for the material investigated here, fatigue lives of LSP treated specimens may be reduced instead of increased due to the occurrence of internal cracking. This paper details the effect of laser power density on fatigue life of 7050-T7451 aluminium alloy by experimental and numerical analysis.

Geometrical effects on residual stresses in 7050-T7451 aluminum alloy rods subject to laser shock peening

Laser shock peening (LSP) is an emerging surface treatment technology for metallic materials, which appears to produce more significant compressive residual stresses than those from the conventional shot peening (SP) for fatigue, corrosion and wear resistance, etc. The finite element method has been applied to simulate the laser shock peening treatment to provide the overall numerical assessment of the characteristic physical processes and transformations. However, the previous researchers mostly focused on metallic specimens with simple geometry, e.g. flat surface. The current work investigates geometrical effects of metallic specimens with curved surface on the residual stress fields produced by LSP process using three-dimensional finite element (3-D FEM) analysis and aluminium alloy rods with a middle scalloped section subject to two-sided laser shock peening. Specimens were numerically studied to determine dynamic and residual stress fields with varying laser parameters and geometrical parameters, e.g. laser power intensity and radius of the middle scalloped section. The results showed that the geometrical effects of the curved target surface greatly influenced residual stress fields.

Geometrical effects on residual stresses in 7050-T7451 aluminum alloy rods subject to laser shock peening

Laser shock peening (LSP) is an emerging surface treatment technology for metallic materials, which appears to produce more significant compressive residual stresses than those from the conventional shot peening (SP) for fatigue, corrosion and wear resistance, etc. The finite element method has been applied to simulate the laser shock peening treatment to provide the overall numerical assessment of the characteristic physical processes and transformations. However, the previous researchers mostly focused on metallic specimens with simple geometry, e.g. flat surface. The current work investigates geometrical effects of metallic specimens with curved surface on the residual stress fields produced by LSP process using three-dimensional finite element (3-D FEM) analysis and aluminium alloy rods with a middle scalloped section subject to two-sided laser shock peening. Specimens were numerically studied to determine dynamic and residual stress fields with varying laser parameters and geometrical parameters, e.g. laser power intensity and radius of the middle scalloped section. The results showed that the geometrical effects of the curved target surface greatly influenced residual stress fields.

CO2 laser manufacturing of miniaturised lenses for lab-on-a-chip systems

This article describes the manufacturing and characterisation of plano-convex miniaturised lenses using a CO2 laser engraving process in PMMA substrates. The technique allows for lenses to be fabricated rapidly and in a reproducible manner at depths of over 200 µm and for lens diameters of more than 3 mm. Experimental characterisation of the lens focal lengths shows good correlation with theory. The plano-convex lenses have been successfully embedded into capillary microfluidic systems alongside planar microlenses, allowing for a significant reduction of ancillary optics without a loss of detection sensitivity when performing fluorescence measurements. Such technology provides a significant step forward towards the portability of fluorescence- or luminescence-based systems for biological/chemical analysis.

Comparative study of the microstructures and mechanical properties of direct laser fabricated and arc-melted AlxCoCrFeNi high entropy alloys

High entropy alloys (HEA) are a relatively new metal alloy system that have promising potential in high temperature applications. These multi-component alloys are typically produced by arc-melting, requiring several remelts to achieve chemical homogeneity. Direct laser fabrication (DLF) is a rapid prototyping technique, which produces complex components from alloy powder by selectively melting micron-sized powder in successive layers. However, studies of the fabrication of complex alloys from simple elemental powder blends are sparse. In this study, DLF was employed to fabricate bulk samples of three alloys based on the AlxCoCrFeNi HEA system, where x was 0.3, 0.6 and 0.85M fraction of Al. This produced FCC, FCC/BCC and BCC crystal structures, respectively. Corresponding alloys were also produced by arc-melting, and all microstructures were characterised and compared longitudinal and transverse to the build/solidification direction by x-ray diffraction, glow discharge optical emission spectroscopy and scanning electron microscopy (EDX and EBSD). Strong similarities were observed between the single phase FCC and BCC alloys produced by both techniques, however the FCC/BCC structures differed significantly. This has been attributed to a difference in the solidification rate and thermal gradient in the melt pool between the two different techniques. Room temperature compression testing showed very similar mechanical behaviour and properties for the two different processing routes. DLF was concluded to be a successful technique to manufacture bulk HEA[U+05F3]s.