The influence of inert impurities on the catalyst lifetime and properties of nanofibrous carbon produced by utilization of diluted hydrocarbon gases

Experimental studies were focused on the feasibility of utilization of hydrocarbons diluted with inert gases (such as associated oil gases) during the synthesis of nanofibrous carbon. The carbon yield and catalyst lifetime were studied regarding the initial reaction mixture parameters. Varying the composition of the initial gas mixture, it is possible to control textural characteristics of the resulting carbon product.

Stability of aqueous films between bubbles. Part 2. Effects of trace impurities and evaporation

The stability of water films has been investigated with a Mysels-Scheludko type film balance. Minor trace impurities in water do not affect the lifetime of water films under vapor saturation, but significantly influence the stability in free evaporation. Trace amounts of positively adsorbed contaminants induce Marangoni-driven flow that destabilizes films under evaporation conditions whereas negatively adsorbed electrolytes actually prolong stability by reversing interfacial tension gradients and driving a steady circulation within the film. At high thinning rates, pure-water films develop exotic-appearing flow patterns and break due to a strong coupling between hydrodynamic and interfacial tensiongradient adsorption stresses. The most dominant factor of transient film stabilization in dynamic conditions under evaporation is a surface tension gradient created in the film. We discuss surface tension gradients in transient films created by temperature differences, impurity concentration, and expansion of the films.

Calcium chemistry of Blue Lake, Mt Gambier, Australia, and relevance to remarkable seasonal colour changes

Calcium speciation and other water quality variables in the Blue Lake, Mt Gambier, Australia, were monitored between August 1999 and August 2000 in order to test previously proposed mechanisms for the seasonal colour changes of this lake. The concentration of calcite was found to be highest in winter when the lake appears grey, and lowest in summer when the lake appears blue. A potential component of the colour change mechanism is therefore identified in which the lake is grey in winter because of non-selective scattering of light by calcite particles, and blue in summer because of the absence of absorbing or scattering impurities.

Alternative methods for the MnO2 oxidation of codeine methyl ether to thebaine utilizing ionic liquids

The MnO2 oxidation of codeine methyl ether, CME, to thebaine has been accomplished via the use of the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate, bmimBF4. The ionic liquid has been used to remove or extract excess MnO2 and associated impurities from the reaction mixture to afford thebaine in 36 to >95% yield. © 2001 Elsevier Science Ltd. All rights reserved.

Study on dehairing of Australian cashmere fibres

Dehairing is the process that removes coarse hair and other impurities from a cashmere fleece in order to obtain luxury fine cashmere fibres. This study has examined and optimised the machine settings on a locally produced cashmere dehairing unit which has led to improvement in the quality of dehaired cashmere fibres. The improved dehairing unit is now in commercial use, adding significant value to the local cashmere industry.

Study of calcium and silicon migration in refractory magnesia

Studied the effect calcium and silicon impurities have on magnesia refractories, a material frequently used to line high-temperature furnaces. Advanced analytical techniques identified and mapped these impurities in both raw materials and finished magnesia refractories. This research considerably enhanced understanding of factors influencing refractory properties and quality.

Wrought magnesium alloy

A magnesium-based alloy consisting of, by weight: 0.5 to 1.5% manganese, 0.05 to 0.5% rare earth of which more than 70% is lanthanum, 0 to 1.5% zinc and 0 to 0.1% strontium, the balance being magnesium except for incidental impurities.

Possible changes of pore size during nanofiltration

The textile industry plays an important role in the world economy as well as our daily life. However, the industry consuming a large quantity of water and generating huge amount of wastewater are unsustainable to the conservation of our precious resources and environment and need improvement. The wastewater, especially the one from spent cotton reactive dyebaths, contains high salt content, various dyes and high alkalinity. This study was carried out to investigate the feasibility of membrane filtration treating spent cotton reactive dye baths. A stirred cell with nanofiltration membrane was used aiming at reusing the reclaimed water. Spent dyebath solutions were synthesized containing hydrolyzed C. I. Reactive Black 5 and sodium chloride. When a piece of membrane was used repeatedly it was expected the flux would decrease after each usage due to fouling of impurities. However, it was found that the water flux increased while dye rejection decreased after each run. At pH 10, the dye rejection decreased significantly. It was proposed that the pore sizes of membrane might have changed during membrane filtration. An equation was derived calculating the possible changes of pore sizes.

Deactivation and regeneration of oxygen reduction reactivity on double perovskite Ba2Bi0.1Sc0.2Co1.7O6−x cathode for intermediate-temperature solid oxide fuel cells

in situ high-temperature X-ray diffraction and thermal gravimetric- differential thermal analysis on room-temperature powder, as well as X-ray diffraction, Raman spectroscopy, and transmission electron microscopy on quenched powder, were applied to study crystal structure and phase transformations in Ba₂Bi_0.1Sc_0.2Co _1.7O_6-x (BBSC). Heating BBSC in air to over 800 °C produces a pure cubic phase with space group Fm3m (no. 225), and cooling down below 800 °C leads to a mixture of three noncubic phases including an unknown phase between 200 and 650 °C, a 2H hexagonal BaCoO3 with space group P63/mmc (no. 194) between 600 and 800 °C, and an intermediate phase at 800 °C. These three phases exist concurrently with the major cubic phase. The weight gain and loss between 300 and 900 °C suggest the occurrence of cobalt reduction, oxidation, and disproportion reactions with dominant reduction reaction at above 600 °C. The thermal expansion of BBSC was also examined by dilatometry. BBSC has a highly temperature-dependent thermal expansion coefficient which relates well with its structure evolution. Furthermore, the oxygen reduction reaction (ORR) of BBSC was probed by symmetrical cell and three-electrode configurations. The presence of hexagonal phase at 700 °C rarely affects the ORR performance of BBSC as evidenced by a slight increase of its area-specific resistance (ASR) value following 48 h of testing in this three-electrode configuration. This observation is in contrast to the commonly held point of view that noncubic phase deteriorates performance of perovskite compounds (especially in oxygen transport applications). Moreover, cathodic polarization treatment, for example, current discharge from BBSC (tested in three-electrode configuration), can be utilized to recover the original ORR performance. The cubic structure seems to be retained on the cathodic polarization - the normal cathode operating mode in fuel cells. Stable 72-h performance of BBSC in cathodic polarization mode further confirms that despite the presence of phase impurities, BBSC still demonstrates good performance between 500 and 700 °C, the desired intermediate operating temperature in solid oxide fuel cells.

Fouling in reverse osmosis (RO) membrane in water recovery from secondary effluent : a review

Reverse osmosis (RO) is the most preferable process for water recovery from secondary effluent (SE) because of its higher rejection of impurities with lower associated cost and higher quality of product. Fouling still is a major challenge during the water recovery due to higher contaminant loadings in SE and high rejection capability of this membrane. The presence of suspended solids, colloidal and organic matters, and high level of biological activities in SE further elevate fouling potentiality. This review was performed to identify major foulants causing hindrance in sustainable application of reverse osmosis and to present available pre-treatment options for these foulants. There are four fouling types present in RO namely; bio-fouling, inorganic/scaling, organic, and particulate fouling. Among them; bio-fouling is less understood but dominant since the pre-treatment options are not well developed. Other fouling mechanisms have been overcome by well developed pre-treatments. The major foulants for RO are dissolved and macromolecular organic substances, sparingly soluble inorganic compounds, colloidal and suspended particles, and micro-organisms. Some of these potential fouling water quality parameters (PFWQPs) are interrelated with each others such as electrical conductivity is a surrogate measure of total dissolved solids with established stable relationship. Most of these PFWQPs such as total suspended solids, turbidity, chemical oxygen demand can be removed by conventional pre-treatment; some such as colloidal particles and micro-organisms by modern options and even others such as endocrine disrupting compounds, pharmaceutical and personal care products are still challenging for current pre-treatments. These foulants need to be identified properly to integrate appropriate pre-treatments for minimizing fouling potentiality to increase water recovery at minimal costs.

Wrought magnesium alloy

A magnesium-based alloy consisting of, by weight: 0.5 to 1.5% manganese, 0.05 to 0.5% rare earth of which more than 70% is lanthanum, 0 to 1.5% zinc and 0 to 0.1% strontium, the balance being magnesium except for incidental impurities.

Monoethanolamine reclamation using electrodialysis

Monoethanolamine (MEA) is the benchmark solvent for the capture of carbon dioxide from both natural gas and flue gas streams. Despite its effectiveness in absorbing CO2, this solvent can react with impurities in the gas stream to form heat stable salts and other degradation products. These impurities can cause problems such as an increase in solvent viscosity and corrosion of the operating units. Thus, a number of approaches have been considered to mitigate the occurrence of these problems. In this paper, the use of electrodialysis as an online MEA reclamation process in a postcombustion CO2 capture facility is investigated. The study shows that high heat stable salts removal can be achieved with a high MEA recovery. However, it is necessary to limit the current density, particularly at lower salt concentrations, to reduce water splitting. The stability of the commercial ion-exchange membranes in the highly alkaline solvent is also investigated. The results show that the membranes are stable upon exposure to 30 wt % MEA for at least 4.5 months.

Nanofiltration for the concentration of heat stable salts prior to MEA reclamation

While monethanolamine has shown great potential as a solvent for the capture of carbon dioxide, impurities can build within the solution over time, leading to increased viscosity and corrosivity. Classically, these impurities are removed by a combination of neutralization and either thermal reclamation, ion exchange or electrodialysis. In this work, we evaluate the use of nanofiltration to concentrate the heat stable salts within the solution prior to such reclamation. This allows the recirculating solvent to operate with low concentrations of these impurities, while providing a low volume, concentrated solution for reclamation. Results show that nanofiltration can reject greater than 80% of the heat stable anions, while allowing the monoethanolamine to permeate through the membrane, for return to the process. Rejection of the MEA itself is less than 7%. The nanofiltration operation is only effective on lean solvent with CO2 loadings of less than 0.2 and neutralization would be required upstream to deprotonate the amine. The two membranes tested (Koch MPF-34 and MPF-36) appeared stable to exposure to the solvent for over four months.

Effect of heat treatment on diffusion, internal friction, microstructure and mechanical properties of ultra-fine-grained nickel severely deformed by equal-channel angular pressing

Severe plastic deformation via equal-channel angular pressing was shown to induce characteristic ultra-fast diffusion paths in Ni (Divinski et al., 2011). The effect of heat treatment on these paths, which were found to be represented by deformation-modified general high-angle grain boundaries (GBs), is investigated by accurate radiotracer self-diffusion measurements applying the 63Ni isotope. Redistribution of free volume and segregation of residual impurities caused by the heat treatment triggers relaxation of the diffusion paths. A correlation between the GB diffusion kinetics, internal friction, microstructure evolution and microhardness changes is established and analyzed in detail. A phenomenological model of diffusion enhancement in deformation-modified GBs is proposed.