21Cr - 10Ni - 3Mo duplex stainless steel high temperature deformation microstructures

Data includes EBSD orentation maps of the specimens deformed in torsion at 1200 degrees celsius to strains of 0.1, 0.5, 0.9 and 1.3. The phase ratio is about 60% austenite and 40% ferrite. The miscrostructure is dynamically recovered and there is also some dynamic recrystallisation at strains of 0.9 and 1.3. The main portion of softening can be attributed to dynamic subgrain coalescence in austenite.

The microstructure evolution and softening processes during high-temperature deformation of a 21Cr-10Ni-3Mo duplex stainless steel

The austenite and ferrite microstructure evolution and softening mechanisms have been investigated in a 21Cr-10Ni-3Mo duplex stainless steel, containing about 60% austenite, deformed in torsion at 1200°C using a strain rate of 0.7 s-1. The above experimental conditions led to the formation of a small volume fraction of new austenite grains through discontinuous dynamic recrystallization (DDRX), which could not account for the observed large softening on the flow curve. DDRX grains mainly formed through the strain-induced migration of the pre-existing austenite grain boundaries, known to dominate in single-phase austenite, complemented by subgrain growth in the interface regions with ferrite. A significant portion of austenite dynamic softening has been attributed to the large-scale subgrain coalescence, the extent of which increased with strain, which seems to have contributed substantially to the observed flow stress decrease. The above process thus appears to represent an alternative mode of austenite dynamic softening to the classical DDRX in the duplex austenite/ferrite microstructure, characterised by limited availability of the pre-existing austenite/austenite high-angle boundaries, deformed at a high temperature. The softening mechanism within ferrite has been classified as "continuous DRX", characterised by a gradual increase in misorientations between neighbouring subgrains with strain and resulting in the progressive conversion of subgrains into "crystallites" bounded partly by low-angle and partly by large-angle boundaries.

Influence of deformation conditions and texture on the high temperature flow stress of magnesium AZ31

The evolution of hot working flow stress with strain is examined in torsion, uniaxial compression and channel die compression. The flow stress was found to be strongly dependent on texture and deformation mode. At low strains this dependency accounted for a difference in flow stress of up to a factor of two. At higher strains the influence of texture and deformation mode was less marked. The stresses corresponding to an equivalent strain of 0.5 were modelled using a power law expression with an activation energy of 147 kJ/mol and a strain rate exponent of 0.15. The influence of texture and deformation mode on flow stress is rationalised in terms of the influence of prismatic slip, twinning and dynamic recrystallisation on deformation stress and structure.

Fabrication of porous TiAl intermetallic compound by self-propagating high temperature synthesis

The present paper describes processing of a lotus-structured porous Ti-Al/Ti composite by SHS with Ti powder and Al rods. Ti-Al intermetallic compound was formed in a range of 200-300μm around the pore by SHS of reaction between Ti and Al, resulting in formation of a lotus-structured porous Ti-Al/Ti composite.

Defect assessment procedures for high temperature applications : final report TW5-TTMS-005, D5

The objective of this task is to develop the high temperature part of a design code for fusion reactor components build from EUROFER. This development includes fracture mechanical rules for the assessment of detected defects under creep and creep–fatigue conditions. The assessment procedures R5, R6, JNC, A16, Partial Safety Factors were investigated and tested. As the most suitable procedure is chosen R5 and it is further verified by comparison with finite element simulations using the EUROFER material data. These simulations consist of evaluation of C(t) parameter for several geometries (CT specimen,cylinder with fully circumferential crack subjected to the internal pressure, cylinder with semi–elliptical circumferential crack subjected to the internal pressure and Mock-Up test blanket module (TBM) geometry). The R5 procedure provides very good accordance with FE simulations and it is suitable for lifetime assessment. Therefore the guide for R5 application is implemented in the report.

Synthesis and characterization of nanocrystalline hexagonal boron carbo-nitride under high temperature and high pressure

A study of the synthesis of hexagonal boron carbo-nitride (h-BCN) compounds via a two-step high-temperature and high-pressure (HTHP) technique using melamine (C 3N 6H 6) and boron oxide (B 2O 3) as raw materials is presented. An amorphous BCN precursor was prepared at 1000K under vacuum in a resistance furnace and then single-phase h-BCN nanocrystalline was synthesized at 1600K and 5.1GPa in a multi-anvil apparatus. X-ray diffraction (XRD) and transmission electron microscopy (TEM) indicated that the final products were pure h-BCN crystals with the lattice constants a ≤ 0.2510nm and c ≤ 0.6690nm. The average grain size was about 150nm. X-ray photoelectron spectroscopy (XPS) results confirmed the occurrence of bonding between C-C, C-N, C-B and N-B atoms. Raman scattering analysis suggested that there were three strong Raman bands centered at 1359, 1596 and 1617cm -1, respectively. The band at 1617cm -1 was considered to be consistent with the characteristic Raman peak of h-BCN.

High-temperature laser-scanning confocal microscopy as a tool to study the interface instability during unsteady-state solidification of low-carbon steel

Solidification microstructure is a defining link between production techniques and the mechanical properties of metals and in particular steel. Due to the difficulty of conducting solidification studies at high temperature, knowledge of the development of solidification microstructure in steel is scarce. In this study, a laser-scanning confocal microscopy (LSCM) has been used to observe in situ and in real-time the planar to cellular to dendritic transition of the progressing solid/liquid interface in low carbon steel. Because the in situ observations in the laser-scanning confocal microscopy are restricted to the surface, the effect of sample thickness on surface observations was determined. Moreover, the effect of cooling rate and alloy composition on the planar to cellular interface transition was investigated. In the low-alloyed, low-carbon steel studied, the cooling rate does not seem to have an effect on the spacing of the cellular microstructure. However, in the presence of copper and manganese, the cell spacing decreased at higher cooling rates. Higher concentrations of copper in steel resulted on an increased cell spacing at the same cooling rates.