Diesel engine performance and emission study using soybean biodiesel blends with fossil diesel

Biodiesel is an ecofriendly and renewable source of energy which can be used as a sustainable alternative fuel fordiesel engine. The study investigated engine performance and emission using soybean biodiesel blends with fossildiesel. The physio-chemical fuel properties of the biodiesel were determined using ASTM and EN standards. Thebiodiesel was blended in different proportions like 5% biodiesel and 95% diesel (by volume) denoted as B5, similarlyB10, B20 and B50. The biodiesel blends were tested in a multicylinder, diesel engine coupled with electromagneticdynamometer, under ISO 8178-4 test procedure. The study found that the biodiesel blends produces less brakepower, brake torque and relatively higher brake specific fuel consumption compared with diesel fuel. However, thesefules significantly reduces exhaust gases namely, CO, CO2 and HC but emits a bit more NOx compared with diesel.The reduction in emissions were different for each biodiesel blends. The study concluded that both B5 and B10blends are the optimum blends that produce more consistant and expected results compared with other blends.

The effect of triacetin as a fuel additive to waste cooking biodiesel on engine performance and exhaust emissions

This study investigates the effect of oxygenated fuels on engine performance and exhaust emission under a custom cycle using a fully instrumented 6-cylinder turbocharged diesel engine with a common railinjection system. A range of oxygenated fuels based on waste cooking biodiesel with triacetin as an oxygenated additive were studied. The oxygen ratio was used instead of the equivalence ratio, or air to fuelratio, to better explain the phenomena observed during combustion. It was found that the increased oxygen ratio was associated with an increase in the friction mean effective pressure, brake specific fuel consumption, CO, HC and PN. On the other hand, mechanical efficiency, brake thermal efficiency, CO2, NOx and PM decreased with oxygen ratio. Increasing the oxygen content of the fuel was associated with a decrease in indicated power, brake power, indicated mean effective pressure, brake mean effective pressure, friction power, blow-by, CO2, CO (at higher loads), HC, PM and PN. On the other hand, the brakespecific fuel consumption, brake thermal efficiency and NOx increased by using the oxygenated fuels. Also, by increasing the oxygen content, the accumulation mode count median diameter moved toward the smaller particle sizes. In addition to the oxygen content of fuel, the other physical and chemical properties of the fuels were used to interpret the behavior of the engine.

Influence of fuel-borne oxygen on European stationary cycle: diesel engine performance and emissions with a special emphasis on particulate and NO emissions

Exploration of sustainable fuels and their influence on reductions in diesel emissions are nowadays a challenge for the engine and fuel researchers. This study investigates the role of fuel-borne oxygen on engine performance and exhaust emissions with a special emphasis on diesel particulate and nitric oxide (NO) emissions. A number of oxygenated-blends were prepared with waste cooking biodiesel as a base oxygenated fuel. Triacetin, a derivative from transesterified biodiesel was chosen for its high oxygen content and superior fuel properties. The experimental campaign was conducted with a 6-cylinder, common rail turbocharged diesel engine equipped with highly precise instruments for nano and other size particles and other emissions. All experiments were performed in accordance with European Stationary Cycle (ESC 13-mode). A commercial diesel was chosen as a reference fuel with 0% oxygen and five other oxygenated blends having a range of 6.02–14.2% oxygen were prepared. The experimental results revealed that the oxygenated blends having higher a percentage of fuel-borne oxygen reduced particulate matter (PM), particle number (PN), unburned hydrocarbon (UBHC) and carbon monoxide (CO) emissions to a significantly low level with a slight penalty of NO emissions. The main target of this study was to effectively utilise triacetin as an additive for waste cooking biodiesel and suppress emissions without deteriorating engine performance. The key finding of this investigation is the significant reductions in both particle mass and number emissions simultaneously without worsening engine performance with triacetin-biodiesel blends. Reductions in both particle mass and number emissions with a cost-effective additive would be a new dimension for the fuel and engine researchers to effectively use triacetin as an emission suppressor in the future.

Comparison of static and dynamic engine models on the transient performance of a passenger vehicle powertrain

This paper presents experimental and computational results obtained on the Ford Barra 190 4.0 litres I6 gasoline engine and on the Ford Falcon car equipped with this engine. Measurements of steady engine performance, fuel consumption and exhaust emissions were first collected using an automated test facility for a wide range of cam and spark timings vs. throttle position and engine speed. Simulations were performed for a significant number of measured operating points at full and part load by using a coupled Gamma Technologies GT-POWER/GT-COOL engine model for gas exchange, combustion and heat transfer. The fluid model was made up of intake and exhaust systems, oil circuit, coolant circuit and radiator cooling air circuit. The thermal model was made up of finite element components for cylinder head, cylinder, piston, valves and ports and wall thermal masses for pipes. The model was validated versus measured steady state air and fuel flow rates, cylinder pressure parameters, indicated and brake mean effective pressures, and temperature of metal, oil and coolant in selected locations. Computational results agree well with experiments, demonstrating the ability of the approach to produce fairly accurate steady state maps of BMEP and BSFC, as well as to optimize engine operation changing geometry, throttle position, cam and spark timing. Measurements of the transient performance and fuel consumption of the full vehicle were then collected over the NEDC cycle. Simulations were performed by using a coupled Gamma Technologies GT-POWER/GT-COOL/GT-DRIVE model for instantaneous engine gas exchange, combustion and heat transfer and vehicle motion. The full vehicle model is made up of transmission, driveshaft, axles, and car components and the previous engine model. The model was validated with measured fuel flow rates through the engine, engine throttle position, and engine speed and oil and coolant temperatures in selected locations. Instantaneous engine states following a time dependent demand for torque and speed differ from those obtained by interpolating steady state maps of BSFC vs. BMEP and speed. Computational results agree well with experiments, demonstrating the utility of the approach in providing a more accurate prediction of the fuel consumption over test cycles.

Performance and gaseous and particle emissions from a liquefied petroleum gas (LPG) fumigated compression ignition engine

In this study, an LPG fumigation system was fitted to a Euro III compression ignition (CI) engine to explore its impact on performance, and gaseous and particulate emissions. LPG was introduced to the intake air stream (as a secondary fuel) by using a low pressure fuel injector situated upstream of the turbocharger. LPG substitutions were test mode dependent, but varied in the range of 14-29% by energy. The engine was tested over a 5 point test cycle using ultra low sulphur diesel (ULSD), and a low and high LPG substitution at each test mode. The results show that LPG fumigation coerces the combustion into pre-mixed mode, as increases in the peak combustion pressure (and the rate of pressure rise) were observed in most tests. The emissions results show decreases in nitric oxide (NO) and particulate matter (PM2.5) emissions; however, very significant increases in carbon monoxide (CO) and hydrocarbon (HC) emissions were observed. A more detailed investigation of the particulate emissions showed that the number of particles emitted was reduced with LPG fumigation at all test settings – apart from mode 6 of the ECE R49 test cycle. Furthermore, the particles emitted generally had a slightly larger median diameter with LPG fumigation, and had a smaller semi-volatile fraction relative to ULSD. Overall, the results show that with some modifications, LPG fumigation systems could be used to extend ULSD supplies without adversely impacting on engine performance and emissions.

The influence of fatty acid methyl ester profiles on inter-cycle variability in a heavy duty compression ignition engine

With the advent of alternative fuels, such as biodiesels and related blends, it is important to develop an understanding of their effects on inter-cycle variability which, in turn, influences engine performance as well as its emission. Using four methanol trans-esterified biomass fuels of differing carbon chain length and degree of unsaturation, this paper provides insight into the effect that alternative fuels have on inter-cycle variability. The experiments were conducted with a heavy-duty Cummins, turbo-charged, common-rail compression ignition engine. Combustion performance is reported in terms of the following key in-cylinder parameters: indicated mean effective pressure (IMEP), net heat release rate (NHRR), standard deviation of variability (StDev), coefficient of variation (CoV), peak pressure, peak pressure timing and maximum rate of pressure rise. A link is also established between the cyclic variability and oxygen ratio, which is a good indicator of stoichiometry. The results show that the fatty acid structures did not have a significant effect on injection timing, injection duration, injection pressure, StDev of IMEP, or the timing of peak motoring and combustion pressures. However, a significant effect was noted on the premixed and diffusion combustion proportions, combustion peak pressure and maximum rate of pressure rise. Additionally, the boost pressure, IMEP and combustion peak pressure were found to be directly correlated to the oxygen ratio. The emission of particles positively correlates with oxygen content in the fuel as well as in the air-fuel mixture resulting in a higher total number of particles per unit of mass.

Effect of noise factors in energy management of series plug-in hybrid electric vehicles

It has been demonstrated that charge depletion (CD) energy management strategies are more efficient choices for energy management of plug-in hybrid electric vehicles (PHEVs). The knowledge of drive cycle as a priori can improve the performance of CD energy management in PHEVs. However, there are many noise factors which affect both drivetrain power demand and vehicle performance even in identical drive cycles. In this research, the effect of each noise factor is investigated by introducing the concept of power cycle instead of drive cycle for a journey. Based on the nature of the noise factors, a practical solution for developing a power-cycle library is introduced. Investigating the predicted power cycle, an energy management strategy is developed which considers the influence of temperature noise factor on engine performance. The effect of different environmental and geographic conditions, driver behavior, aging of battery and other components are considered. Simulation results for a modelled series PHEV similar to GM Volt show that the suggested energy management strategy based on the driver power cycle library improves both vehicle fuel economy and battery health by reducing battery load and temperature.

Modelling and testing of long range battery electric vehicle performance

There are two significant issues facing road transport in the medium to long term: the depletion of cheap oil reserves and the need to reduce carbon emissions. A long term solution for passenger cars could be the introduction of battery electric vehicles (BEVs). However, one of the main problems associated with the current generation of BEVs is their short range relative to conventional internal combustion engine (ICE) cars.

To investigate this issue, a long range battery electric vehicle, the UltraCommuter (UC), was constructed by the University of Waikato in partnership with HybridAuto Ltd. This paper describes the development, modelling and testing of the UC and its performance in the 2007 World Solar Challenge.