Drying and denaturation characteristics of α-lactalbumin, β-lactoglobulin, and bovine serum albumin in a convective drying process

Drying and denaturation kinetics of aqueous droplets of α-lactalbumin (α-lac), β-lactoglobulin (β-lg), and bovine serum albumin (BSA) were measured in a convective drying environment. Single droplets having an initial droplet diameter of 2 ± 0.1 mm and containing 10% (w/v) protein concentration were dried using conditioned air (65 and 80 °C, 2-3% RH, 0.5 m/s velocity) for 600 s. The denaturation of these proteins was measured by using reversed-phase HPLC. At the end of 600 s of drying 13.3 and 19.4% α-lac was found to be lost due to denaturation at 65 and 80 °C, respectively. Up to 31.0% of β-lg was found to be denatured, whereas BSA was not found to be significantly (p > 0.05) denatured in these drying conditions. The formation and strength of skin and the associated morphological features were found to be linked with the degree of denaturation of these proteins. The secondary structure of these proteins was significantly (p < 0.05) affected and altered by the drying stresses. The β-sheet and random coil contents were increased in α-lac by 6.5 and 4.0%, respectively, whereas the α-helix and β-turn contents decreased by 5.5 and 5.0%, respectively. The β-sheet and random coil contents in β-lg were increased by 7.5 and 2.0%, respectively, whereas the α-helix and β-turn contents decreased by 3.5 and 6.0%, respectively. In the case of BSA the β-sheet, α-helix, and random coil contents were found to increase, whereas the β-turn content decreased.

Structure retention in cross-linked poly(ethylene glycol) diacrylate hydrogel templated from a hexagonal lyotropic liquid crystal by controlling the surface tension

Retaining hexagonal lyotropic liquid crystal (LLC) structures in polymers after surfactant removal and drying is particularly challenging, as the surface tension existing during the drying processes tends to change the morphology. In this study, cross-linked poly(ethylene glycol) diacrylate (PEGDA) hydrogels were prepared in LLC hexagonal phases formed from a dodecyltrimethylammonium bromide (DTAB)/water system. The retention of the hexagonal LLC structures was examined by controlling the surface tension. Polarized light microscopy, X-ray diffraction and small angle X-ray scattering results indicate that the hexagonal LLC structure was successfully formed before polymerization and well retained after polymerization and after surfactant removal when the surface tension forces remained neutral. Controlling the surface tension during the drying process can retain the nanostructures templated from lyotropic liquid crystals which will result in the formation of materials with desired nanostructures.

Retention of the original LLC structure in a cross-linked poly(ethylene glycol) diacrylate hydrogel with reinforcement from a silica network

Cross-linked poly(ethylene glycol) diacrylate (PEGDA) hydrogels with uniformly controlled nanoporous structures templated from hexagonal lyotropic liquid crystals (LLC) represent separation membrane materials with potentially high permeability and selectivity due to their high pore density and narrow pore size distribution. However, retaining LLC templated nanostructures is a challenge as the polymer gels are not strong enough to sustain the surface tension during the drying process. In the current study, cross-linked PEGDA gels were reinforced with a silica network synthesized via an in situ sol-gel method, which assists in the retention of the hexagonal LLC structure. The silica precursor does not obstruct the formation of hexagonal phases. After surfactant removal and drying, these hexagonal structures in samples with a certain amount of tetraethoxysilane (TEOS) loading are well retained while the nanostructures are collapsed in samples without silica reinforcement, leading to the hypothesis that the reinforcement provided by the silica network stabilizes the LLC structure. The study examines the conditions necessary for a sufficient and well dispersed silica network in PEGDA gels that contributes to the retention of original LLC structures, which potentially enables broad applications of these gels as biomedical and membrane materials.

Physicochemical and functional properties of protein isolate produced from Australian chia seeds

Protein was isolated from Australian chia seeds and converted to powders using spray, freeze and vacuum drying methods, to investigate the effect of drying methods on physicochemical and functional attributes of chia-seed protein isolate (CPI). It was found that there was no significant difference in the proximate composition; however vacuum dried CPI (VDCPI) had the highest bulk density and oil absorption capacity, whereas spray dried powder (SDCPI) demonstrated the highest solubility, water absorption capacity and lowest surface hydrophobicity. Solubility of all powders was higher at elevated temperature and alkaline pH. Foaming capacity and foam stability of CPI were found to increase with increasing pH and protein concentration. SDCPI was the least denatured and VDCPI the most denatured, demonstrating the poorest solubility and foaming properties of the latter. These findings are expected to be useful in selection of a drying process to yield chia seed protein powders with more desirable functionality.

Solar thermal drying of canarium indicum nuts

Many situations exist in rural areas of developing countries where the help of simple technology can make substantial positive impacts on living conditions, finance, and in this case; sustainability. In the Melanesia region, there are numerous areas identified as needing improvement, including indigenous food preservation which will be addressed with a proposed solar thermal solution utilizing locally available materials as much as possible for low cost local construction. The current knowledge of the drying requirements for the product chosen in this study is quite limited. However, it is believed that solar thermal drying might be feasible for the remote sunny regions as in Melanesia. This paper describes the processes involved in determining the drying parameters of the Canarium indicum nut, and the proposed solar dryer designs that have been considered for the particular environmental conditions and product specifications. Through the selection process, a mixed mode, low-tunnel solar dryer was chosen as the best match to satisfy the different parameters.

Excellent electrochemical performance of LiFe0.4Mn0.6PO4 microspheres produced using a double carbon coating process

Composite LiFe0.4Mn0.6PO4/C microspheres are considered advanced cathode materials for electric vehicles and other high-energy density applications due to their advantages of high energy density and excellent cycling stability. LiFe0.4Mn0.6PO4/C microspheres have been produced using a double carbon coating process employing traditional industrial techniques (ball milling, spray-drying and annealing). The obtained LiFe0.4Mn0.6PO4 microspheres exhibit a high discharge capacity of around 166 mA h g-1 at 0.1 C and excellent rate capabilities of 132, 103, and 72 mA h g-1 at 5, 10, and 20 C, respectively. A reversible capacity of about 152 mA h g-1 after 500 cycles at a current density of 1 C indicates an outstanding cycling stability. The excellent electrochemical performance is attributed to the micrometer-sized spheres of double carbon-coated LiFe0.4Mn0.6PO4 nanoparticles with improved electric conductivity and higher Li ion diffusion coefficients, ensuring full redox reactions of all nanoparticles. The results show that the advanced high-energy density cathode materials can be produced using existing industry techniques.