Diesel exhaust particulate matter induces multinucleate cells and zinc transporter-dependent apoptosis in human airway cells

The cellular effects of biodiesel emissions particulate matter (BDEP) and petroleum diesel emissions particulate matter (PDEP) were compared using a human airway cell line, A549. At concentrations of 25 µg/ml, diesel particulate matter induced the formation of multinucleate cells. In cells treated with a mixture of 80% PDEP:20% BDEP, 52% of cells were multinucleate cells compared with only 16% of cells treated with 20% PDEP:80% BDEP with a background multinucleate rate of 7%. These results demonstrate a causal relation between the formation of multinucleate cells and exposure to exhaust particulate matter, in particular diesel exhaust. Exposure of A549 cells to PDEP induced apoptosis, seen by active caspase-3 expression and the presence of cleaved pancytokeratin. PDEP exhaust was a much stronger inducer of cellular death through apoptosis than BDEP. There was an eightfold increase in the expression of SLC30A3 (zinc transporter-3 or ZnT3) in cells exposed to 80% PDEP:20% BDEP compared to untreated cells. The increase in ZnT3 expression seen in apoptotic cells following PDEP suggests a role for this zinc transporter in the apoptotic pathway, possibly through controlling zinc fluxes. As exposure to diesel exhaust particles is associated with asthma and apoptosis in airway cells, diesel exhaust particles may directly contribute to asthma by inducing epithelial cell death through apoptotic pathway.

Major grass pollen allergen Lol p 1 binds to diesel exhaust particles : implications for asthma and air pollution

Background Grass pollen allergens are known to be present in the atmosphere in a range of particle sizes from whole pollen grains (approx. 20 to 55 μim in diameter) to smaller size fractions < 2.5 μ (fine particles, PM2.5). These latter particles are within the respirable range and include allergen-containing starch granules released from within the grains into the atmosphere when grass pollen ruptures in rainfall and are associated with epidemics of thunderstorm asthma during the grass pollen season. The question arises whether grass pollen allergens can interact with other sources of fine particles, particularly those present during episodes of air pollution.

Objective We propose the hypothesis that free grass pollen allergen molecules, derived from dead or burst grains and dispersed in microdroplets of water in aerosols, can bind to fine particles in polluted air.

Methods We used diesel exhaust carbon particles (DECP) derived from the exhaust of a stationary diesel engine, natural highly purified Lol p 1, immunogold labelling with specific monoclonal antibodies and a high voltage transmission electron -microscopic imaging technique

Results DECP are visualized as small carbon spheres, each 30–60 nm in diameter, forming fractal aggregates about 1–2μ in diameter. Here we test our hypothesis and show by in vitro experiments that the major grass pollen allergen, Lol p I. binds to one defined class of fine particles, DECP.

Conclusion DECP are in the respirable size range, can bind to the major grass pollen allergen Lol p I under in vitro conditions and represent a possible mechanism by which allergens can become concentrated in polluted air and thus trigger attacks of asthma.

Distilled technical cashew nut shell liquid (DT-CNSL) as an effective biofuel and additive to stabilize triglyceride biofuels in diesel

We report distilled technical cashew nut shell liquid (DT-CNSL) as a non-transesterified biofuel and also as an additive to convert triglycerides to biofuel, without the need for the formation of methyl esters. DT-CNSL blends of diesel obey physico-chemical parameters of diesel. DT-CNSL offers stability to blends of straight vegetable oil (SVO) and tallow oil in diesel. Fluorescence studies using charge transfer probes show that the blend of DT-CNSL, triglycerides and diesel is a uniform solution, and fluorescence behavior is similar to that of diesel. The economics for the cultivation of cashew (Anacardium occidentale), its industrial use and rich carbon sink properties indicate that DT-CNSL could complement or replace traditional biodiesel crops like Jatropha and improve income for farmers. © 2014 Elsevier Ltd.

Inter-cycle variability of ignition delay in an ethanol fumigated common rail diesel engine

An experimental study has been performed to investigate the ignition delay of a modern heavy-duty common-rail diesel engine run with fumigated ethanol substitutions up to 40% on an energy basis. The ignition delay was determined through the use of statistical modelling in a Bayesian framework this framework allows for the accurate determination of the start of combustion from single consecutive cycles and does not require any differentiation of the in-cylinder pressure signal. At full load the ignition delay has been shown to decrease with increasing ethanol substitutions and evidence of combustion with high ethanol substitutions prior to diesel injection have also been shown experimentally and by modelling. Whereas, at half load increasing ethanol substitutions have increased the ignition delay. A threshold absolute air to fuel ratio (mole basis) of above ~110 for consistent operation has been determined from the inter-cycle variability of the ignition delay, a result that agrees well with previous research of other in-cylinder parameters and further highlights the correlation between the air to fuel ratio and inter-cycle variability. Numerical modelling to investigate the sensitivity of ethanol combustion has also been performed. It has been shown that ethanol combustion is sensitive to the initial air temperature around the feasible operating conditions of the engine. Moreover, a negative temperature coefficient region of approximately 900{1050 K (the approximate temperature at fuel injection) has been shown with for n-heptane and n-heptane/ethanol blends in the numerical modelling. A consequence of this is that the dominate effect influencing the ignition delay under increasing ethanol substitutions may rather be from an increase in chemical reactions and not from in-cylinder temperature. Further investigation revealed that the chemical reactions at low ethanol substitutions are different compared to the high (> 20%) ethanol substitutions.

A statistical model for combustion resonance from a DI diesel engine with applications

Introduced in this paper is a Bayesian model for isolating the resonant frequency from combustion chamber resonance. The model shown in this paper focused on characterising the initial rise in the resonant frequency to investigate the rise of in-cylinder bulk temperature associated with combustion. By resolving the model parameters, it is possible to determine: the start of pre-mixed combustion, the start of diffusion combustion, the initial resonant frequency, the resonant frequency as a function of crank angle, the in-cylinder bulk temperature as a function of crank angle and the trapped mass as a function of crank angle. The Bayesian method allows for individual cycles to be examined without cycle-averaging|allowing inter-cycle variability studies. Results are shown for a turbo-charged, common-rail compression ignition engine run at 2000 rpm and full load.

Diesel engine performance and emission study using soybean biodiesel blends with fossil diesel

Biodiesel is an ecofriendly and renewable source of energy which can be used as a sustainable alternative fuel fordiesel engine. The study investigated engine performance and emission using soybean biodiesel blends with fossildiesel. The physio-chemical fuel properties of the biodiesel were determined using ASTM and EN standards. Thebiodiesel was blended in different proportions like 5% biodiesel and 95% diesel (by volume) denoted as B5, similarlyB10, B20 and B50. The biodiesel blends were tested in a multicylinder, diesel engine coupled with electromagneticdynamometer, under ISO 8178-4 test procedure. The study found that the biodiesel blends produces less brakepower, brake torque and relatively higher brake specific fuel consumption compared with diesel fuel. However, thesefules significantly reduces exhaust gases namely, CO, CO2 and HC but emits a bit more NOx compared with diesel.The reduction in emissions were different for each biodiesel blends. The study concluded that both B5 and B10blends are the optimum blends that produce more consistant and expected results compared with other blends.

Inter-cycle variability of in-cylinder pressure parameters in an ethanol fumigated common rail diesel engine

The effects of ethanol fumigation on the inter-cycle variability of key in-cylinder pressure parameters in a modern common rail diesel engine have been investigated. Specifically, maximum rate of pressure rise, peak pressure, peak pressure timing and ignition delay were investigated. A new methodology for investigating the start of combustion was also proposed and demonstrated—which is particularly useful with noisy in-cylinder pressure data as it can have a significant effect on the calculation of an accurate net rate of heat release indicator diagram. Inter-cycle variability has been traditionally investigated using the coefficient of variation. However, deeper insight into engine operation is given by presenting the results as kernel density estimates; hence, allowing investigation of otherwise unnoticed phenomena, including: multi-modal and skewed behaviour. This study has found that operation of a common rail diesel engine with high ethanol substitutions (>20% at full load, >30% at three quarter load) results in a significant reduction in ignition delay. Further, this study also concluded that if the engine is operated with absolute air to fuel ratios (mole basis) less than 80, the inter-cycle variability is substantially increased compared to normal operation.

Influence of fuel-borne oxygen on European stationary cycle: diesel engine performance and emissions with a special emphasis on particulate and NO emissions

Exploration of sustainable fuels and their influence on reductions in diesel emissions are nowadays a challenge for the engine and fuel researchers. This study investigates the role of fuel-borne oxygen on engine performance and exhaust emissions with a special emphasis on diesel particulate and nitric oxide (NO) emissions. A number of oxygenated-blends were prepared with waste cooking biodiesel as a base oxygenated fuel. Triacetin, a derivative from transesterified biodiesel was chosen for its high oxygen content and superior fuel properties. The experimental campaign was conducted with a 6-cylinder, common rail turbocharged diesel engine equipped with highly precise instruments for nano and other size particles and other emissions. All experiments were performed in accordance with European Stationary Cycle (ESC 13-mode). A commercial diesel was chosen as a reference fuel with 0% oxygen and five other oxygenated blends having a range of 6.02–14.2% oxygen were prepared. The experimental results revealed that the oxygenated blends having higher a percentage of fuel-borne oxygen reduced particulate matter (PM), particle number (PN), unburned hydrocarbon (UBHC) and carbon monoxide (CO) emissions to a significantly low level with a slight penalty of NO emissions. The main target of this study was to effectively utilise triacetin as an additive for waste cooking biodiesel and suppress emissions without deteriorating engine performance. The key finding of this investigation is the significant reductions in both particle mass and number emissions simultaneously without worsening engine performance with triacetin-biodiesel blends. Reductions in both particle mass and number emissions with a cost-effective additive would be a new dimension for the fuel and engine researchers to effectively use triacetin as an emission suppressor in the future.